Search Documents

By J. D. Zhou, F. Yang, X. G. Bi

"In this investigation, the phosphorus distribution ratios in the CaF2 system and B2O3 system dephosphorization slags for high-phosphorus hot metal pretreatment were measured by an indirect method under laboratory conditions. Firstly, the phosphorus distribution ratio between liquid slag and solid iron was measured, and then the phosphorus distribution ratio between liquid slag and hot metal was calculated. Phosphorus capacity was calculated in terms of the composition and optical basicity of the slag. Dephosphorization slag was also studied by scanning electron microscopy, energy dispersive analysis, and X-ray diffraction analysis. The experimental results show that the phosphorus capacity of the B2O3 slag system is much greater than that of the CaF2 system. It is demonstrated thatB2O3 can completely replace CaF2 as fluxing agent for high-phosphorus hot metal pretreatment. With CaF2 as fluxing agent, the phosphorus capacity increases with increasing CaO content in the slag, but the phosphorus distribution ratio decreases. B2O3, when used as fluxing agent, can react with high melting point phases such as 2CaO·SiO2 and 3CaO·P2O5 in the slag to form new phases with low melting points such as 11CaO·B2O3.4SiO2, 2CaO·B2O3.SiO2, and Ca9.93(P5.84B0.16O24) (B0.67O1.79), thereby acting as a fluxing agent. When the ratio of w(B2O3)/w(CaO) is 0.16, the phosphorus distribution ratio reaches its maximum value, that is, the dephosphorization ability of the slag is at its maximum. IntroductionAs international iron ore prices continue to rise, the development of China's steel industry is facing a lot of pressure. Against this background, development and utilization of domestic high-phosphorus iron ore resources is particularly important. When highphosphorus iron ore is used in ironmaking, the phosphorus content in the hot metal can reach 0.35% or more, and the hot metal must be pretreated. For hot metal with 0.08–0.10% dissolved phosphorus, the traditional hot metal dephosphorization pretreatment technologies are relatively mature. However, when using these methods to dephosphorize hot metal containing 0.35% P or more, the amount of dephosphorization slag can reach 100–150 kg per ton of hot metal. Furthermore, the traditional dephosphorization methods require the addition of large amounts of CaF2 as fluxing agent, and this results in high fluoride levels in the dephosphorization slag. The fluorine in the slag can partially dissolve in water and thereby causes high fluoride concentration in the water and soil. Once the fluoride is absorbed by humans or animals, it can result in toxic effects on the central nervous system and myocardium. In addition, fluoride can accumulate in the environment, and thereby pose a health risk to animals and humans through the food chain (Li, 2007; Liu, Wang, and Dong, 2011, Diao, 2013). The objective of this research is to replace CaF2 with B2O3 as fluxing agent while achieving the expected goals of hot metal pretreatment."

Jan 1, 2016

By J. O. Claassen

"SynopsisMining value chains are dynamic systems and should be managed according to systemic flow-based principles. This includes a detailed focus on the impact of variable geological conditions on material flow, product quality, and production cost, visibility of the total mining system to operators and managers, as well as the synchronization of resources and activities in downstream processes. Thirty mining operations across the African continent were studied to establish to what extent systemic flowbased principles are applied in day-to-day operations. The study indicated that although most mining operations have identified the relevant geoprocessing variables, only a small number apply this information in a flow-based management approach. Most mining operators do not focus on developing a clear flow view of the mining value chain and on making it visible to operators and managers to enable them to optimally set and reset operations. Daily synchronization of geoprocessing variables is limited to a small number of variables, e.g. synchronizing ore hardness with drilling or milling requirements, in less than 30% of the operations evaluated. Operations where these principles have been adopted reported a noteworthy improvement in performance. The study indicates that notable potential exists in most of the operations evaluated to implement flowbased management principles, including geometallurgical principles. This can significantly improve value chain performance without exorbitant capital layouts and enhance ROCE. IntroductionObjective of the studyThe study seeks to establish to what extent systemic flow-based principles have been adopted in the southern African mining industry and the implications thereof. Specific attention is given to the importance of defining and managing geoprocessing dependencies (geological variables directly impacting mining and plant performance – the geometallurgical approach), establishing a flow view of the mining system, which typically includes a dashboard of the flow of ore/product quality and cost from the mining face to the customer, and limiting the impact of dependencies through synchronization of activities and resources, e.g. ensuring that a continuous miner does not wait for a roofbolter, or that reagent addition rates are matched with a specific ore/concentrate composition."

Jan 1, 2015

By N. Duda, P. Śliwiński, P. Stefaniak, B. Jachnik

Ventilation and air-conditioning are some of the most energy-consuming processes in deep underground mining. Additionally, the energy consumption of these processes systematically increases along with the expansion of the mine. Therefore, proper energy efficiency assessment and consumption forecasts of these systems are particularly important in modern mines for ongoing tracking and planning of the likely costs. In the article, a short-term prediction model for surface air–conditioning stations is described. This model takes into account dependencies that were identified, based on the data from the supervisory control and data acquisition (SCADA) systems. These dependencies between the response value and the external conditions are then incorporated into the model. This way, for example, the ambient temperature or the total number of specific days of the week (with sometimes significantly lower or higher than the weekly average energy consumption levels) are included. Taking into account these dependencies, and e.g. forecasted average monthly temperatures allow us to include the seasonality of energy consumption in the presented model. In the article, a sample energy efficiency analysis of the A/C system based on an example of the KGHM Polish Copper Polkowice-Sieroszowice mine is performed. The results of the solution proposed in the article are then evaluated, and compared to the currently functioning, more basic forecasting methods. However, given the general nature of the dependencies used in the model, similar solutions could be used in other case studies.

Sep 1, 2021

By Mike de Wit

Of the approximately 6,500 kimberlites known to date, less than 3% are diamondiferous and less than half of those are economically viable. Admittedly, this is a global figure and varies from area to area much depending on geological, logistical, and political circumstances. The number of diamond-bearing kimberlites is an important geobarometer, and an age-frequency profile has been compiled in order to identify diamond metallogenic epochs and provinces. Four primary diamond clusters have been recognized: Siberia (332-370Ma), Kaapvaal South(114-144Ma), Kaapvaal Southwest(84-95Ma), and Slave (52-55Ma). In addition, three secondary clusters are the Kaapvaal Central (S06-S38Ma), the Man Craton (139-lS3Ma) and the Kasai Craton (120-130Ma). The Kaapvaal is the only area where kimberlites with diamonds were discovered between 1870 and 1925, except for the Prairie Creek discovery in North America in 1906 and Colossus in Zimbabwe in 1907. Between 1906 and 1940 no major diamondiferous kimberlites were discovered, but many of Africa's alluvial deposits were found and exploited in that period. Advances in scientific prospecting in the 1940's rapidly accelerated the discovery rate that peaked in the 1990's; 39 diamondiferous occurrences were found in the 1980's, of which 8 became mines and 5 are in feasibility, and nearly 450ha of kimberlite was added to the global resource base. Despite the accelerated exploration expenditure, the last decade (e.g. 2000-2009) has been the leanest since the 1940's. The most important reason for this decline in exploration success is that any undiscovered deposits are largely buried by younger cover. Understanding complex and geophysical noisy basement geology, as well as decomposition of path-finder minerals are major challenges to further exploration success. Major investments in basic geological expertise and field research will have to be made in order to secure future diamond resources. Integrated geophysical studies, geochemistry diamond forensics, and improved imaging of Earth's upper mantle are perhaps foremost in this requirement, but the costs of these activities are such that government support will be required if countries are to sustain their diamond mining industry.

Jan 1, 2010

By O. O. Ogunmodimu, D. K. Weatherley, M. S. Powell

Discrete element methods (DEM) have provided the ability to resolve the complex phenomena experienced by ore within comminution devices such as tumbling mills. The new developments in DEM techniques and the corresponding increase in computational power have made it more feasible to study the movement of individual ore particles as they traverse a tumbling mill. A range of information can be extracted on individual particle impact histories, such as kinetic energy at the time of collision, velocities of individual particles, per-particle stress tensors, impulse, and collision energy. DEM codes have been modified to provide required information that can be analysed in associated software to investigate the impact of varied operational parameters on the resultant granular dynamics. This paper explores the reaction of individual ore particles to the breakage environment within a tumbling mill using DEM techniques and studies the stressing conditions that would lead to either impact or abrasive breakage. Keywords: DEM, comminution, tumbling mill, breakage

Jan 1, 2020

By K. Cole, D. Mesa, P. R. Brito-Parada, M. R. van Heerden

Turbulence in stirred tank flotation vessels determines the bulk transport of particles and has an important role in particle-bubble collisions necessary for attachment. Positron emission particle tracking (PEPT) produces quantitative measurements of the kinematic motion of different particle classes inside flotation vessels. This paper presents flow profiles of the vessel, residence time distributions, flow profiles through the mesh and macroturbulent kinetic energy distributions as experienced by valuable (hydrophobic) mineral particles in a laboratory scale flotation vessel. The results highlight the impact of the rotor-stator design and a retrofit mesh modification at the upper part of the vessel which improve recovery by decreasing turbulence in the quiescent zone and at the interface. Keywords: Flotation machines, turbulence, PEPT

Jan 1, 2020

By S. A. Villalobos, F. A. Villalobos, and L. E. Aguilera

Rockburst events have been a serious problem for many years in many mines worldwide, and in particular at El Teniente mine in Chile. El Teniente is the largest copper mine in the world, located in the Andes Cordillera where high stress levels are present due to intensing mining activity in addition to complex geology. Consequently, the study and management of the rockburst threat are necessary. In this work, the case of the Diablo Regimiento (DR) mine within El Teniente is studied. The energy capacity of dynamic support systems is determined for different tunnel geometries based on two kinetic methodologies, using data from DR. Initially, rockburst potential is determined by means of a stress analysis around different tunnel geometries through the boundary elements method. In the first methodology a yielding zone (YZ) is estimated for each excavation geometry using the finite element method FEM. The second methodology involves the definition and determination of a critical strain energy (SE) around each excavation geometry using a FEM numerical analysis. In both cases, peak particle velocity PPV is estimated by a scaling law, which is subsequently adjusted due to tunnel amplification effects. According to the results, and knowing the working energy capacity applied in DR mine, it was found that the values of energy capacity for the rock dynamic supports were better estimated by the YZ-PPV approach than by the SE approach.

Sep 1, 2022

By M. Stachowiak, M. Nowicki, K. Walas, A. Skoczylas, P. Stefaniak

In this paper the authors present a walking robot dedicated to the inspection of a belt conveyor’s transportation system in an underground mine. The developed robot can independently diagnose all of the key rotating elements of the belt conveyor (pulleys, bearings, drums, gears, engines) based on vibration and acoustic signals as well as typical RGB (red, green, blue) and thermal images. The article presents key diagnostic procedures applied to real industrial data obtained during robot testing.The work was developed as part of the ‘THING–subTerranean Haptic INvestiGator’ project. The authors presented the main assumptions of the research methodology developed for the needs of technical diagnostics of conveyor elements typical of inspection work performed by mining staff. Based on industrial data, the use of algorithms for elements such as rollers, drive stations, and the conveyor belt were shown. The main assumption of the research is to develop a robot adapted to the conditions of a deep mine, capable of carrying out an autonomous inspection of mining infrastructure. The conducted tests and the developed fault detection algorithms were aimed at preparing the robot for underground tests in the operating conditions of the mine.

Sep 1, 2021

By M. Royker

Gold has been demonstrated as a possible catalyst for oxidation reactions. Some evidence for a possible promotion effect of platinum has also been recorded. The influence of platinum as promoter for Au/?-Al2O3 prepared via anionic ion-exchange for the oxidation of glycerol was investigated in a batch reactor at 60°C. It is inferred that the addition of platinum reduces the catalytic activity and the rate of deactivation, resulting in an overall higher final conversion of glycerol with increasing platinum loading. The addition of platinum to the catalyst favours the formation of the desired product, glyceric acid.

Jan 1, 2012

By W. C. Joughin

The science of soil mechanics is 100 years old, and rock mechanics is about 80 years old. While methods of analysis and design have been developed and have evolved over time, these are relatively young sciences. The rapid increases in computing power and new technologies have enabled more sophisticated modelling and monitoring. However, there are still many aspects of soil and rock mechanics that are not well understood. Geotechnical failures, which have major consequences, still occur. These consequences may include environmental damage, major production holdups and associated loss of revenue, damage to infrastructure, and loss of life. High-consequence events, which are rare, are more difficult to anticipate and to design for, because by their nature they involve extraordinary circumstances or conditions, often geological in nature. The risks are usually mitigated by conservative designs and monitoring. Detailed geotechnical investigations help us to understand the natural variability of soil and rock masses and identify unusual or unexpected conditions. Investigating and researching major geotechnical failures is essential to enable these unusual circumstances to be anticipated. In the past, severe unanticipated events may have been treated as natural events or ‘acts of God’. However, society now has much greater expectations and it is essential to have policies and procedures in place that enable appropriate management of these rare, high-consequence risks. A good example is the Global Industry Standard on Tailings Management (GISTM), which was introduced after the catastrophic dam collapse at Vale’s Corrego de Feijao mine in Brumadinho, Brazil. The address will explain the concepts of uncertainty and variability, and how they should be taken into account in geotechnical design. The challenges facing geotechnical engineers, mine owners, and managers will be discussed. referencing a number of real case studies.

Sep 6, 2023

By J. Engelbrecht

Understanding the deportment of minerals in size fractions has already led to improvements in the flow sheets for platinum minerals beneficiation. There are, however, more potential changes in the flow sheets that may improve the recovery of platinum group metals or reduce the costs of beneficiation before refining. Based on known technology of pre-concentration, milling, gravity concentration, flotation, and magnetic separation a number of potential alterations or additions can be considered and motivated based on the mineral deportment in size fractions.

Jan 1, 2012

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By I. O. Ondicho, E. K. Mutinda, B. O. Alunda, E. Agyekum

Driven by the necessity to improve blast performance regarding fragment size distribution in limestone mines, this paper introduces the prediction and measurement of blast fragmentation distribution through the modified Kuz-Ram (MKR) and Kuznetsov-Cunningham-Ouchterlony (KCO) models. Precise prediction and measurement of rock fragmentation resulting from blasting play a critical role in hard rock ore extraction. This is due to the substantial influence of post-blast ore size distribution on the efficiency of all subsequent downstream rock handling and processing operations. Additionally, employing secondary breakage of boulders, when necessary, leads to an unjustified rise in production costs. In this paper, the MKR and KCO models were utilised to identify the most appropriate model for application in Bisil and Simba quarries situated in Kajiado County, Kenya. Split-Desktop was used for blast fragment measurement by processing digital images obtained after blasting and computing the fragment size distribution of the blasted rock. As per the investigation, the recorded percentages of boulders generated at the sites ranged from 7% to 12.3% for the Simba quarry and from 11.2% to 23.9% for the Bisil quarry, respectively. Regression, correlation, and root mean square error (RMSE) were employed as the primary performance indicators. The study concluded that KCO outperformed MKR in accurately predicting blast fragment sizes in the examined quarries.

Mar 5, 2025

By E. Spicer

X-Ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems in XRD creates the opportunity to use this technique in modern process control. In the analysis of heavy mineral sands, XRD can identify the main mineral phases, such as ilmenite FeTiO3, rutile TiO2, Zircon ZrSiO4and quartz SiO2, and any other minor components present, such as anatase TiO2, magnetite Fe3O4, haematite Fe2O3or monazite (Ce, REE)PO4. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis (Bish and Howard, 1988) are attractive alternatives, as they do not require any standards or monitors. These methods offer impressive accuracy and speed of analysis. The Rietveld method compares calculated versus experimentally derived X-ray powder diffraction patterns for the sum of all crystalline phases. Another analysis technique offering great benefit to mining industries is cluster analysis. Enormous amounts of XRD measurement data are generated during the process control and material evaluation. New ways of handling such vast amounts of data are required to produce meaningful information for the end users. Cluster analysis greatly simplifies the analysis of a large amount of data from different processes or different raw materials, and automatically sorts closely related scans of an experiment into clusters and marks the most representative scan of each cluster as well as outlying patterns. The use of cluster analysis to evaluate the XRD data allows fast and reliable tracking of the process. It is the most economical procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimization methodologies, results, data precision and limitations will be discussed. The approach has potential as a relatively inexpensive, reliable tool, useful in the characterization of heavy minerals sand materials.

Jan 1, 2007

By G. Mahieu, L. Perez-Barnuevo, P. Barbeau-Verreault, O. Gravel

Raglan mine is a copper-nickel mining operation, part of Glencore, and located at the northern border of the province of Quebec, in Canada. The concentrator is fed by a mix of four different underground mines, thus it must accommodate periodic variations in run-of-mine mineralisation and composition. In order to concentrate nickel and copper sulphides, the flotation circuit also includes a regrind step at the cleaner stage. This leads to challenges in maintaining optimal recoveries and in diagnosing potential disturbances. This paper advocates for the combination of automated mineralogical analyses, reconciliated mass balances from diagnostic sampling campaigns and innovative multidimensional visualisation to assist in tackling these challenges. Through this approach, it has been possible to quantify the regrind step influence on the liberation of valuable mineral particles in the final flotation concentrate. The methodology also allows for virtual sieving of the products in order to track unit loss in the flotation process. The proposed analysis scheme presents an opportunity to easily diagnose flotation circuit performance based on mineralogical information. Keywords: Flotation diagnostics, multi-dimensional visualisation, mineral liberation analysis

Jan 1, 2020

By G. Akdogan, P. Mutimutema, M. Tadie

The South African gold mining industry has a legacy of abundant tailings dams, which have attracted the attention of investors because of their potential as a cheaper secondary gold resource. In this we investigate study gold recovery from a refractory calcine tailings dam. Bulk mineralogy of the tailings silicates and iron oxides to be the most abundant phases. Scanning Electron Microscopy (SEM) showed gold to exist in submicrometre and micrometre sizes, as free gold, and associated with arsenic, sulphur, and silicates e.g. quartz and talc. Gold recovery by direct cyanidation was low at 17.3%. Mechanical (ultra fine grinding P80 -16μm) and chemical (alkaline, NaOH) pre-treatment and microwave roasting and microwave-assisted cyanide leaching were investigated to increase gold recoveries. Ultrafine grinding was the most effective, producing recoveries of 66.5%. NaOH pre-leaching of ultrafine milled material increased recovery to 71.5%. Alkaline pre-leaching overall increased recoveries for non-pretreated material, making this process the most preferred because it is less costly than ultrafine grinding. Microwave roasting and microwave-assisted leaching did not achieve higher recoveries than alkaline pre-treatment or fine grinding. The investigation highlights and confirms that chemical treatment with NaOH is a powerful tool for gold extraction from refractory tailings.

Oct 1, 2022

The October General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 21st October, 1970, at 4.30 p.m. V. C. Robinson (President) was in the chair. There were also present 25 Fellows, including J. K. E. Douglas, Prof D. D. Howat, D. G. Maxwell, Dr R. E. Robinson, P. A. von Wielligh (Council Members). D. Ayres, G. Burrow, E. H. D. Carman, D. L. Carson, M. E. E. Douglas, S. A. Finney, W. R. Flook, A. J. Freemantle, W. A. Gilbert, E. B. Gordon, B. W. Gray, J. M. Jacobs, P. H. Kitto, C. H. Kruger, Dr P. J. D. Lloyd, D. G. Malan, W. Pilkington, W. G. Pyne-Mercier, K. S. Rae, W. T. Ruhmer, D. J. Tutt and D. T. Watt. Seven Members, including E. J. Dominy, S. I. du Preez, L. V. Grobler, D. R. Lings, G. D. Louw, J. S. A. Oelofse and O. B. Prentis. Fifteen Visitors, including J. R. Coppin, Dr A. Faure, P. E. Franzl, G. P. Hart, D. van Heerden, A. W. Hunt, A. R. F. MacDonald, B. G. Meyburgh, P. H. Radcliffe, J. M. Shirley, T. H. Tunley, A. D. Vellema and R. E. Wheeler. Secretary, D. C. Visser. Total present: 49. OBITUARIES The President: "It is my sad duty to announce the death of the following: Sir George Arthur Davenport, Honorary Life Fellow, who joined the Institute in 1930 and passed away on 17th September, 1970. The late Sir George was also, for many years, our corresponding member for Rhodesia. Andrew Malcolm Carmichael, Associate, who joined the Institute in 1944 and passed away on 22nd August, 1970. Cyril John Douglas Veal, Life Fellow, who joined the Institute in 1929 and passed away on 27th August, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." CONFIRMATION OF MINUTES The President: "May we confirm the minutes of the Annual General Meeting held on 26th August, 1970, and the minutes of the monthly general meetings which were held on the 20th of May and the 17th of June, 1970, as published in the August Journal." Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5.2.2., Council has elected them to membership of the Institute in the following grades: Members: Nikolaos Lalakakis, Gordon Phillips Rundle. Associates: Henry du Preez, James Robert Forbes, Johannes Stephanus Albertus Oelofse, Casper Vorster van Heerden. Graduates: Michael Harold Crosbie, Graham Robert Wallis Walker, Gary Walker Braithwaite. Students: Mohammad Ali Kazemzadeh, Gerhardus Petrus Benade. APPLICATIONS FOR TRANSFER From Graduate to Member: James Wormald. From Student to Graduate: Peter John Cook, Pieter Willem Greeff. "I welcome the newly elected members to the Institute and congratulate the members who have been transferred to a higher grade." PAPER FOR PRESENTATION The President: "This paper is entitled 'The Design, Erection and Operation of a Purlex Plant at Buffelsfontein Gold Mining Company Limited'. It is presented to the Institute by Mr B. G. Meyburgh, a visitor to our Institute. He is a graduate of the University of the Orange Free State and is the Uranium Plant Superintendent at Buffelsfontein and he, therefore, is in a very strong position to describe this very excellent job which is being done as he has been associated with this plant from the inception." After the presentation of the paper the President said: "Gentlemen, the paper you've heard from Mr Meyburgh is a very concise and interesting account of an important piece of work, and I think the title is so completely descriptive of the subject, which is admirably set out in the paper which you have heard. You probably haven't all had the opportunity of reading it, but you very soon will. I found it interesting to note that the results predicted were surpassed in the operation of the plant to date. The actual results obtained are significantly good, I think. Any process which, in this country, increases production and decreases costs, is to be welcomed, particularly when it is so necessary for South Africa almost to bend over backwards to utilise every avenue available in order to increase the scope of the production for overseas' markets, of her metallurgical and mineral potential. In lighter vein-and there is no reason why we should always be so serious-I am glad to see that, in a scientific journal like this, such words as the American word 'crud' which I have been picked out about so often, because my grandchildren use it, is now given an aura of respectability. Thank you very much, Mr Meyburgh, for an interesting paper. We have a long list of contributors, and I am not going to waste any more time. I am going to call on Mr Tunley of the N.I.M. for the first contribution." T. H. Tunley, P. de Bruyn (read by A. D. Vellema), E. J. Dominy, E. H. D. Carman, A. R. F. MacDonald D. C. Streicher (read by P. H. Radcliff), Dr A. Faure and Dr P. J. D. Lloyd then contributed to the discussion. (This discussion will appear in a later issue of the Journal.) The President: "I wish to thank members and visitors for their attendance, and now declare the meeting closed." The meeting closed at 6.05 p.m.

By K. Barani, F. Moradpouri, M. Godarzi

A sampling campaign carried out on the lead flotation circuit at Lakan lead-zinc processing plant demonstrated that the Pb recovery was only about 68-69%. Characterization of the Pb flotation tailing showed that 61.4% of the Pb is in the –37 μm size fraction, which is difficult to recover by flotation. Batch flotation experiments were carried out on a plant sample of the lead flotation feed and high-intensity conditioning (HIC) was used to improve flotation recovery. The results showed that increasing the collector conditioning time from 1 to 3 minutes significantly increases the Pb recovery from 42.5% to 57.3%. Further increases in conditioning time to 5 to 7 minutes decreased the Pb recovery. With a collector conditioning time of more than 3 minutes, due to the surface cleaning effect, increasing collector and frother dosage improved the flotation selectivity and recovery, even at higher collector dosages. The Pb recovery increased from 69.1% to 79.8% with increasing impeller speed from 600 to 1250 r/min. HIC increases the flotation kinetics and greatly improves the flotation recovery and concentrate grade.

Apr 2, 2022

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives have several potential pitfalls. These are outlined in the present paper. The main findings are as follows:•,Coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate •,For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where, ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition •,Significant errors could be made if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen) •,For elemental analyses, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range •,For representation of sulphur in coal, double-counting due to SO3 in the ash analysis should be avoided •,Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2; however, use of some of these species without considering the experimentally determined gross CV results in significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy (up to 6.9% error for a set of South African coals). Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than the abovementioned four, provided the enthalpy is corrected •,It is recommended that an ‘enthalpy correction value’ is incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to the form of carbon being different than graphite should be used, as that would imply doublecounting some effects."

Jan 1, 2014

By E. K. Mutinda, D. K. Maina, R. M. Kasomo, B. O. Alunda

Assessment of blast fragment size distribution is critical in mining operations because it is the initial step towards mineral extraction. Different empirical models and techniques are available for predicting and investigating the consequences of blasting, one of which is the Kuznetsov Cunningham-Ouchterlony (KCO) model. In this paper we summarize the advances in the empirical models from inception until now, and explore the improvements that have been made so far with particular emphasis is on the most recent KCO model. Utilization of the model and the errors that arise between expected and the actual outcomes are analysed. The results indicate that the KCO model remains useful for predicting the blast fragmentation at limestone mine sites, despite the availability of other advanced prediction models. It is also a valuable instrument for pre-surveying the impact of varying certain parameters of a blast plan.

Mar 1, 2021