Search Documents

By C. A. Garzonio, A. M. G. Affuso

The paper describes the analyses and the tests carried out on representative slabs of white Carrara marble which have highlighted the correlation between the micro fabrics and physical and mechanical parameters. The aim is to determine the conditions which indicate the triggering and evolution of the deformation phenomena. La note écrit l’analyse et les epreuves effectuée sur un echantillon représentatif de nombreuses dalles en marbrede Carrara. Les études montrent la correlation entre la minéralogie et les paramètres physiques et mecaniques. Le but est déterminer les conditions qui indiquent l’amorçage et l’evolutions des phénomènes de déformation. Diese Arbeit gibt eine Beschreibung der experimentalen Untersuchungen und der Analysen über die Marmorplatten von Carrara. Daraus resultiert, dass die Charakterisierung der Mineralogie und die Porosität der Gesteinsmaterialien die physikalische mechanische Degradation beurteilen und die Krümmungen bestimmen.

Jan 1, 2003

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By N. Patel

Many factors, from engineering and design to supply, installation, and operation affect the service lifespan of cast refractory linings. If a shortcoming occurs at any of these stages, the lining lifespan can be drastically reduced. Although not every aspect that can affect a cast refractory lining?s lifespan is outlined here, a few key points are highlighted, with an emphasis on the various installation parameters. Keywords cast linings, refractory lifespan, lining engineering and design, lining supply, lining installation, curing, dry-out.

Aug 1, 2013

By D. J. de Clerk

Global trends stipulate the need to optimize existing assets while reducing environmental impacts. This paper illustrates the procedure that was followed to achieve such goals at one of the coal burning flash dryer units at an Anglo American smelter. An in-depth study of the process and related literature led to the development and installation of a revised control philosophy. This system includes modifications to the existing regulatory control structure as well as a hybrid rule-based and model-predictive advanced process control (APC) layer. Since commissioning of the APC, this flash dryer?s average throughput has increased by more than 6%, despite higher feed moistures. Furthermore, even though coal consumption has increased slightly, operating efficiency has improved by close to 5%. This was made possible by improving stability of the drying column outlet temperature by approximately 40%, which in turn enabled selection of a more optimal setpoint. Recent data has shown that APC utilization now exceeds 95%. This is indicative of a successful controller installation with good site acceptance. The same philosophy has therefore since been rolled out to most of the other flash dryers in the group.

Jan 1, 2012

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS© Expert system together with three VisioRockTM online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS© is the first installation to incorporate Metso Minerals Process Technology-Asia Pacific's (MMPT AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS© logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007

By T. Wallmach

Heavy mineral deposits are a source of the economic important element titanium, which is contained in minerals such as ilmenite, pseudorutile and rutile. In the Ranobe heavy minerals deposit these minerals occur not only as primary unaltered minerals but also display various degrees of alteration resulting in an increased titanium content of the deposit. The presence of the various FeTi-oxide minerals? textural relations is a reflection of geological processes and may ultimately be used to unravel the geological history of the deposit. These minerals have different chemical and physical properties that influence metallurgical tests and the quality of products produced from various mineral beneficiation streams. It is therefore of metallurgical importance that the minerals are well characterized, defined and monitored during preliminary beneficiation tests.

Jan 1, 2007

By John Taylor

?Introduction to Black Mountain ?Historical metal accounting practice ?Metal accounting audit ?Feed measurement ?Sample precision ?Concentrate measurment ?Current metal accounting practice ?Further refinements to the metal accounting practice

Jan 1, 2005

By D. Francois-Bongarcon

The ?Poisson effect? is defined and characterized. It takes place even when the material to sample is not liberated. Gy, Pitard, Ingamells, and others, including the author, recommend that a minimum average number of particles of mineral of interest characterize the recommended sample size. How many? Recommended numbers range from 6 to 40 particles depending on authors, corresponding to standard deviations of 41% to 16%. Some guidelines are proposed, and the often alleged ?double-Poisson? effect is examined.

Jan 1, 2009

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

While some of the practical details of ilmenite smelting are not well documented, there is a substantial body of literature on the principles of ilmenite smelting, and the behaviour of solidified titania slag. This information is summarized, focusing on the basic reactions, departure from equilibrium, the behaviour of impurities, and reactions of solidified slag. The emphasis is on the South African operations.

Jan 1, 2007

Nowadays, fully encapsulated rockbolts have become a key element in the design of ground control systems. The main reason is that they offer high axial resistance to bed separation. In this research, the load transfer capacity of a fully grouted bolt is evaluated analytically in an elastoplastic rock mass condition. The research considered the effect of bolt end-plate on load transfer capacity. Bolt and surrounding materials were assumed to be elastic and elastoplastic materials respectively. The load transfer mechanism of a fully grouted bolt is a function of parameters such as bolt length, shear stiffness of interfaces, in situ stress, presence of face-plate and distance along the bolt. These factors were analytically evaluated. Finally, the load along the bolt was predicted in different surrounding rock mass characteristics.

Jan 1, 2011

By B. M. Kunar

It is well known that job-related hazards and individual factors influence occupational injuries. However, research involving coalminers has been limited. This case-control study assessed the relationships of job-related hazards and individual/life style factors with injuries among underground coal miners. It compared 245 cases with at least one injury during the previous two-year period with 245 matched controls with no injury. The data were gathered via personal interview and analysed using the conditional logistic model. The significant risk factors were materials handling (adjusted OR 5.15), poor environmental/working conditions (2.63), geological/strata control-related hazards (2.35), lack of formal education (3.00), sleep disorders (1.86), alcohol consumption (2.32), disease (2.23), having a large family (5.40), and risk-taking behaviour (9.40). Machine-related hazards, sleep disorders and alcohol consumption primarily affected workers aged less than 45 years; whereas, environment/working condition-related hazards, presence of disease, smoking, risk-taking behaviour and large family size were more likely among workers aged 45 or over. Keywords: Occupational injuries, sleep disorders, job hazards, alcohol, coal miners

Jan 1, 2010

By C. Rodrigues

This investigation compares the gas adsorption behaviour and capacity of three bituminous coals from South Africa, of similar rank, by assessing the characteristics of the raw coal, as well as the resulting float and sink fractions (at 1.80 cm3/g) obtained by density separation of crushed coal samples. Calculations were also made to obtain the raw coal gas storage capacity from the weighted contribution of both float and sink fractions results, thereby permitting comparison with the analysed results of the raw coal. The study demonstrated that the clean fraction of a coal has the highest capacity to retain gas in the sorbed state, followed by raw coal, and lastly the sink fraction, and re?confirmed previous investigations that showed minerals to be inhibitors of gas adsorption and retention.

Jan 1, 2008

By Y. -L. Chiang

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) The generation and control of manganese sulphide particle size distribution using various mixing configurations were investigated. Specifically, this paper discusses how varying mixing intensities on a macro and micro scale affect the resultant manganese sulphide particle size distribution (PSD) at a constant concentration. The mixing variations were achieved using various Y- and T-mixers as premixing devices into a jacketed, agitated vessel. The reagents used to generate the seeds were aqueous manganese sulphate and sodium sulphide solutions. The results showed that the absence of micromixing resulted in very poor control of the particle size distribution, the particle size and the number of particles produced. This was due to the fact that the macromixing time is much greater than the corresponding precipitation time, resulting in different mixing regions existing within the reactor. From the micromixing experiments, the T?mixer was found to be the most effective mixing device at lower concentrations due to the T-mixer providing a faster mixing time than the other mixing configurations, thereby effectively localizing the supersaturation and hence controlling the precipitation. The results obtained from the direct addition without the extension pipe (i.e. short mixing time) indicated a general increase in mean particle size and decrease in total particle number at reagent concentration of 0.007 mol.dm-3as compared to the corresponding micromixing experiments. The phenomenon may be due to incomplete crystallization at the immediate exit of the mixing device. Further experiments need to be conducted before any conclusions can be drawn about the precipitation mechanisms.

Jan 1, 2007

By E. J. McLean

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

By R. Tabanrad

This article examines the stability analysis of intake tunnels of Karun III dam & power plant. The tunnels have been excavated with a 3-dimensional and fairly complicated geometry in Pabdeh weak formation rocks at Zagros region. Due to the particular excavation geometry and inapplicability of plane-strain status, the stability of these excavations has been analyzed using both the 3D elastic software Examine 3D and the 2D non-elastic software UDEC simultaneously. The geomechanical parameters have been estimated by back analyzing the measured displacements from instruments, which were installed in the tunnels, and the parameters have been used in non-elastic numerical model. The results of the analysis show that the strains occurred in surrounding rock mass are less than the allowable failure strain and that the tunnels are stable. In addition, considering the results of non-elastic 2D analysis, the areas with unstable potentiality were identified and after the instability occurred at the areas predicted by the model , it was stopped up to the allowable strain limit through installing additional support . Bei diesem Artikel handelt es sich um eine Analyse der Festigkeit der Eingangstunnel des Damms und Elektrizitätswerks “Karoon III”.Die Tunnel haben drei Dimensionen und eine sehr schwierige Form und sind in brüchigen Felsen in “Pabedeh ,in Zagrossgebirge”eingebohrt.Aufgrund besonderer Form der Bohrung wurde ihre Festigkeit durch elastische dreidimensionale Soft-ware analysiert,die gleichzeitig die drei-und zweidimensionale unelastische Soft-ware UDEC benutzt hat.Die geometrische Parameter sind mit Ausnützung der Analyse berechneter eingesetzter Versorgungen,die in Tunnel aufgebaut sind,bewertet.Und diese Parameter sind in Zahlen-Analyse benutzt.Die Ergebnisse dieser Analyse zeigen,dass die Drücke an Felsen weniger als problematischer Grad der Drücke sind und die Tunnel fest sind.Ausserdem wurde mit einem Einblick auf die Ergebnisse der unelastischen zweidimensionale Analyse die eventuellen unfesten Teile bestimmt.Nach entstandener Unfestigkeit an diesen Teilen wurde die problematischeDrücke für Aufbau mehrere Anlagen gestoppt. Cet article examine l'analyse de la stabilité de tunnels de la prise de Karoun barrage III et centrale électrique. Les tunnels ont été excavés avec une 3 dimensionnel et compliqué géométrie dans Pabedeh que la formation faible balance à région Zagros équitablement. Dû à la géométrie de l'excavation particulière et inapplicabilite de statut de tension plane, la stabilité de ces excavations a été analysée en utilisant les deux le 3D logiciel élastique Examen 3D et le 2D logiciel non - élastique UDEC simultanément. Les paramètres du geomechanical ont été estimés en analysant le déplacement mesuré d'instruments qui ont été installés dans les tunnels et les paramètres en arrière a été utilisé dans les modèles numériques non - élastique. Les résultats de l'analyse montrent que les tensions se sont produites dans masse du roc environnante est plus petit que la tension de l'échec admissible et que les tunnels sont stables. De plus, les régions avec potentialité instable ont été identifiées étant donné les résultats de 2D analyse non - élastique, et après que l'instabilité se soit produite aux régions prédites par le modèle, il a été arrêté jusqu'à la limite de la tension admissible à travers installer du support supplémentaire.

Jan 1, 2003

By K. R. Noble

The planned extraction of the No. 1 shaft pillar at Blyvooruitzicht Gold Mine highlighted a number of potential problems. In spite of the relative shallowness, careful thought had to be given to stope phasing owing to the detrimental effect of the anticipated geology and the fact that uninterrupted hoisting was necessary. Extensive use was made of computer modellig to design the stope phasing, determine the influence of regional support and to predict the direction and magnitude of displacements in the shaft. The paper describes the success of this design approach, and measured displacements in the stoping horizon and shaft barrel are compared to those obtained from the original computer model

Jan 1, 1987

By D. C. Andersen, G. L. Smith, A. M. Marsh, J. Pearson-Taylor

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2006

This paper presents the development of a regrind facility design at BHP Billiton's Leinster Nickel Operations (LNO) in Western Australia. The recovery opportunity was identified from an analysis of plant operating data together with scanning electron microscope (SEM) measurements on relevant tailings streams from LNO. A laboratory procedure was developed to determine the potential recovery improvement of installing a regrind facility at LNO. The last step in formulating the process flow sheet and defining the process design criteria was to construct and operate a pilot plant, which incorporated four banks of flotation cells and an Xstrata M20 Isa Mill. Pilot plant on/off trials were used to define the expected metallurgical benefit. A prefeasibility engineering design and cost estimate was completed. Following a successful internal business evaluation, a feasibility study is currently underway.

Jan 1, 2007

By R. G. B. Pickering

The South African narrow reef hard rock mining industry has been stuck in a time warp with relatively little change in the mining process in the last century. This paper presents a methodology on how to implement change in narrow reef hard rock mining. It then explores a number of technologies that have been introduced into this mining industry and the impact that they have had on the mining process. The author then presents his view on whether the defined change process has been followed and sets out to identify the most critical aspect of ensuring that change is successfully implemented. Future demand will also be speculated on.

Jan 1, 2007