Search Documents

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By M. Khandrika, B. K. Parekh

Column flotation has proven to be the most effective technique for the flotation and recovery of ultrafine coal. The commercial application of columns in the coal industry is steadily increasing (Parekh et al., 1990; Yoon et al., 1992). For the flotation of coal or mineral air is used for generating bubbles. Using a conventional flotation cell, Miller and Mishra (1985) compared froth flotation behavior of fine coal using air, nitrogen and carbon dioxide gas. They concluded that carbon dioxide gas provided a higher rate of recovery and a lower ash content. The objective of the present study was to investigate the effect of various gases such as compressed air, nitrogen, argon, and carbon dioxide on the column flotation of fine coal.

Jan 1, 1999

By A. K. Bakshi

In cold regions, rinsing of spent cyanide from leach heaps is stopped during winter and is resumed again after the snow melts. The effect of this idle time on the overall removal process was studied in this experiment. Samples were collected for rinsing tests from one heap at a gold mine near Fairbanks, Alaska. Continuous and interrupted rinsing of this sample were carried out in test columns. The rinse solution was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that total cyanide concentration per rinse cycle for interrupted rinsing test was higher than for the corresponding continuous rinsing test. As a result, interrupted rinsing required less rinsing cycles than continuous rinsing.

Jan 1, 1995

By John D. Nelson, Clint L. Strachan

Drainage of tailings impoundments is a key issue for impoundment stability, water control, seepage control, and reclamation. Drainage control is an established operating practice where climate and site conditions permit, such as in South Africa and various mines in North America. In these areas, drainage control is primarily used to maximize tailings densities and to provide adequate impoundment stability. Drainage practices during operation also become an important issue when tailings impoundments are reclaimed. Time required for cover placement and post- reclamation seepage control depends greatly on the ability for tailings to drain and consolidate. This paper discusses drainage issues associated with gold tailings impoundments in terms of mechanics of saturated and unsaturated flow and experience with design and reclamation of tailings impoundments.

Jan 1, 1988

By L. Xu, R. Bhaskar

While a NIOSH accepted procedure exists for determination of quartz in the respirable dust samples from coal mines, no specific procedure has been defined for quartz determination in bulk samples. In this study, the effect of particle size on the estimation of quartz using the infrared technique was evaluated. Several laboratory tests were performed to determine the dependence of the infrared absorbance peak height on the different sizes of quartz particles. The significant dependence observed between quartz particle size and the measured peak height indicates the potential for erroneous interpretation of the quartz in bulk samples depending on how the samples are prepared. A procedure to reduce the effect of size in the determination of the quartz content is suggested.

Jan 1, 1994

By B. K. Parekh, R. H. Mehta

Handling of fine coal is an importance issue for coal as well as the utility industry. Reconstitution in form of pellet or briquet would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders e.g., asphalt- emulsion, corn starch and Brewex, in forming pellets of ultra-fine clean coal. It was found that asphalt emulsion and corn starch were not effective binders for ultra-fine clean coal, however, Brewex provided excellent quality of pellets, which exceeded all the minimum quasi requirements of coal pellets. INTRODUCTION Advanced coal preparation techniques (physical or chemical) are designed to process ultra-fine (minus 200 mesh or 74 pm) coal. The average particle size of the clean coal product is about 25 pm. Currently available dewatering techniques are effective in providing a 25 to 30 percent moisture product of this size coal slurry (Parekh et al. 1989). Handling and utilization of this dewatered ultra-fine size coal is difficult. Reconstitution, which includes pelletization, briquetting, extrusion, etc., of the dewatered coal product provides an ideal answer to handling and transportation problems. However, reconstitution of fines in the coal industry has not been successful due to various reasons. The most important criterion for its unsuccessful application in the coal industry is the cost of the binder (Capes et al. 1965). Various methods of reconstitution, such as briquetting, disk pelletization, extrusion pelletization and roller and die-pelletization, have been tested for fine coal agglomeration (Conkle et al., 1991) (Richards, 1990). Conkle et al., (1992) have provided a detail analysis of each technique in terms of moisture and operating cost requirements. According to Conkle, briquetting requires a product containing very low moisture, whereas pelletization can be done with coal containing up to 30 percent moisture. Currently available dewatering technique provides about 25 percent moisture product, thus, pelletization appears to be an ideal route for reconstitution. In this paper, results are presented on the comparison of three different binders i.e., asphalt-emulsion, corn starch and Brewers condensed solids (BCS or Brewex), for fine coal pelletization.

Jan 1, 1995

By Wenhua Li, Tsuyoshi Adachi

Resource nationalism is essentially mandatory government intervention in natural resources businesses by political or economic means in order to benefit the nation and the people. It is attacking the mining industry more and more rampantly by all kinds of means since the twenty-first century. Poor countries who count on a resource-led economic growth usually find themselves trapped into “resource curse”. The harmfulness of resource nationalism for investors is that one event can quickly escalate and lead to a chain of events which make projects commercially unavailable. In spite of historical and theoretical social investigations in the causes of resource nationalism, rare studies engaged in quantification of dominant parameters of it. The objective of this study is to find significant factors that dominate the occurrence of resource nationalism for important metal and energy resources producing countries and quantify their marginal effects. The study applies binary choice logit model for panel data using pooled method. One feature of the research is that binary data set of occurrence of resource nationalism are sorted out by authors referencing U.S. Geological Survey’s reports. The results indicate that high-technology export (% manufactured export), ores and metals exports (% merchandise exports), rule of law (world governance indicator), trade (% GDP), and natural resource rent except forest (% GDP ) dominant the occurrence of resource nationalism for high and upper middle income group countries; government effectiveness (world governance indicator), policy perception index (The Fraser Institute), high-technology export (% manufactured export), and mineral rent (% GDP) dominant the occurrence of resource nationalism for lower middle and low income countries. According to our model, probability of occurrence of resource nationalism in 90 countries are predicted. Top 10 risky countries in 2012 are estimated to be North Korea, India, Honduras, Indonesia, Kazakhstan, Burkina Faso, Mongolia, Cuba, Bolivia, and Peru. The study is a primary trial of researching on resource nationalism and provides some insights for theoretical building and simulation on the issue.

Jan 1, 2017

By V. Srajer

This paper deals with the problem of efficiently selecting the most appropriate loading and hauling equipment for surface mines. Problems and factors that affect productivity and operating cost are identified. During the course of collecting the information for this study, mining companies and equipment manufacturers were interviewed to define their selection practices. The majority of mining companies prepare general specifications and ask the suppliers to mate those specifications to their product line. The mining company then evaluates various proposals on the basis of the best available deal. The following 'mines from western Canada provided information for this study: Coal Mountain, Line Creek, Quintette, Westar's Harmer mine from the Province of British Columbia, and Coal Valley, Gregg River, Highvale, Luscar from the Province of Alberta.

Jan 1, 1989

By George H. K. Schenck

Decisions to develop deposits of calcareous materials for cement production are based largely on anticipated markets for heavy construction which utilizes concrete. The geologist should understand the fundamental factors that underlie such management decisions, so that his field work and reports will more effectively relate to the information requirements of managers in the cement industry. The paper examines the relationships that exist between exploration and development of calcareous raw materials for cement manufacture and changing factors in the marketing of cement. Continued overcapacity, improved technology, changing distribution patterns, ease of entry, economics of scale, and the nature of product demand are some of the characteristics of the cement industry that are basic to decisions regarding exploration programs and property development.

Jan 1, 1966

By H. J. Sohn, S. G. Doo

A systematic study was carried out to investigate the reduction reaction mechanism of oxygen on pyrite surface using electrochemical techniques. The polarization curves showed two distinct regions, the Tafel region for superoxide formation and limiting current region for diffusion of dissolved oxygen to form hydrogen peroxide. These results were confirmed with a-c impedance measurements.

Jan 1, 1990

By G. Stephan Derrickson

Any type of agitation within a confined vessel is primarily concerned with two parameters: 1) A level of agitation describing the homogeneity of the constituents (whether it be suspension or mixing) and, 2) the energy efficiency with which this level of agitation is accomplished. The following is an attempt to present a solution to the problem of adequately defining and optimizing these properties. First included is a discussion of the application of good design practices to the determination of a mechanically efficient shape to the blade elements of the propeller. These practices, excluding several appropriate modifications, have been known, but not well understood, in aircraft fluid mechanics for a number of years. Secondly, having optimized the direct impartation of energy to the medium being agitated, attention is turned to one of the more perplexing phenomena of multi-phase systems - definition and prediction of agitation levels. The result of recent study and testing is a method of scaling which the authors feel provides a lucid understanding of governing physical parameters within the agitator itself, allowing one to scale up and down with confidence.

Jan 1, 1982

By B. L. Seegmiller

Regular entry trusses are used in headgates, tailgates, roadways and intensely-faulted areas. These trusses have proven to give the required support and maintain roof stability even under major abutment loading conditions for both the re-treating and advancing longwalls. Areas previously requiring steel arches have been eliminated. A special Continuous Entry Truss? provides permanent support to adjacent tunnel/crosscut zone for more than 300 feet in each tunnel. The continuous nature of the tensioned truss allows sup-port forces to be placed on the roof in not just the two-dimensions of regular trusses, but in a full three-dimensions. A newly developed Roktruss? provides support in an arched 30-foot high rock zone. The Roktruss? allows truss support concepts to be used in an opening with a curved roof.

Jan 1, 1989

By P. Corser

Operational and geotechnical constraints on mining within steeply dipping deposits and historic landslide areas, which are characteristic of subarctic coal deposits in Alaska, will be discussed. The current plan for mining through these areas will be presented, as well as an alternative plan for minimizing the adverse effects of mining through an historic landslide area.

Jan 1, 1988

By Murdoch Mackenzie

"Organic Polymers used as gangue depressants are classified according to their chemical structure. Absorption mechanisms for these reagents at the mineral - water interface are reviewed. The method of selecting these reagents for a particular flotation system is discussed. Details are given of methods of reagent solution make-up and distribution. Plant addition policy is reviewed.”

Jan 1, 1986

By Gordon E. Ager

A technique for the synthesis of mineral processing flowsheets from laboratory batch test data is described and examples of the application of the procedure are given. The procedure requires the collection of kinetic data, the optimization of the flotation time in each separation stage, then simulation of the material balance for a continuous circuit.

Jan 1, 1989

By Steve Lloyd, Mary Anne Antonioli, Byron Darnton

The Pegasus Gold/Montana Tunnels Mine is a high­tonnage, low-grade, base and precious metal operation in Jefferson City, Montana. Gold heads are typically 0.02 opt with the dominant gold mineral being a native metal electrum quite rich in silver. Early research and development indicated the ore to be amenable to gravity concentration at a 10 to 14 mesh grind. Although full flow gravity preconcentration was considered as a flowsheet alternative, flotation was chosen as the main recovery process due to its apparent lower cost for capital and operating. At this early juncture, the option or concept of recovering coarse free gold by gravity was deemed unnecessary or irrelevant. The intermittent loss of free gold has been observed in the flotation tailing since mill start up. A comprehensive research program was initiated in 1990 to identify the magnitude of this loss and investigate alternatives for its recovery. Batch and pilot plant testing has ultimately led to a permanent gravity circuit being installed at the cyclone underflow. The circuit is designed to scalp out the liberated coarse gold contained in the ball mill circulating load. The final flowsheet consists of: a pinched sluice to upgrade cyclone underflow; a Tyler doubledeck screen to remove over­size from sluice concentrate; Knelson concentrators for roughing and cleaning of screen undersize; an Eriez wet drum separator to remove tramp metal from Knelson concentrate; a Sweco screen to size Knelson cleaner concentrate for tabling; and a Wilfley table to produce final concentrate for direct melting.

Jan 1, 1992

By G. E. McCormack

The Development of Water Gel Explosives Water gels are the most recent development in the evolution of commercial explosives. They are replacing dynamite, having proven themselves to be excellent alternatives to this standard explosive. Water gels have steadily displaced dynamite over the past two decades. In 1959, they accounted for only 1 percent of the market they share with dynamite. By 1965, the share taken by water gels had grown to 21 percent. In 1970, it was more than 40 percent, and today it is nearly 70 percent. Black powder, the first widely used explosive, revolutionized mining and quarrying in its day. However, when nitroglycerin dynamite became available about a century ago, it rapidly displaced black powder because it provided greater energy for a given weight, much higher velocity for better rock shattering performance, and water resistance for easy use in wet conditions. During the past 50 years, ammonium nitrate has played a dramatically increasing role in explosives. First, it was used as an ingredient in dynamite, and then as the main component in nitrocarbonitrate blasting agents. About a quarter of a century ago, it began to find use in a simple and inexpensive mixture with fuel oil that has revolutionized the explosives industry and today fills about 80 percent of the requirements for explosives in the U.S., and certainly the bulk of blasting requirements worldwide. Water gels and dynamites share the remaining 20 percent. Water gel explosives based on ammonium nitrate have also been developed during the past quarter century. These explosives contain

Jan 1, 1979

By Ann M. Gosier

Over the past 20 years, diesel-powered equipment has been introduced into the underground mining environment in increasing numbers. While the introduction began years earlier in the metal-nonmetal sector, the exponential growth in coal mining use during this time has been more pronounced. Reasons for the continued use and rapid growth of diesel equipment in underground mines are easily understood. The safety and operational advantages afforded by this equipment in production and support systems are demonstrable. As other mine operators witness the advantages enjoyed by their competitors, they too move to introduce an increasingly diverse array of such equipment into their underground mines. As with any industrial technology, the use of diesel-powered equipment entails potential safety and health concerns. Existing Mine Safety and Health Administration (MSHA)approval regulations (30 CFR Parts 31, 32 and 36) apply only to diesel locomotives and mobile diesel-powered equipment for noncoal mines. In the absence of specific regulations, MSHA has required the use of equipment approved under Part 36 (gassy noncoal mines) for areas of underground coal mines where permissible electrical equipment is required. However, a considerable amount of diesel-powered equipment without explosion-proof or fire prevention features is in use in areas of coal mines where permissible electrical equipment is not required. It is on the use of this latter class of equipment that MSHA is focusing much of its regulatory attention relative to coal. The agency also is focused on revising existing occupational exposure limits for gaseous emissions and instituting limits on diesel particulate emissions for both coal and metal-nonmetal mines.

Jan 1, 1993

By T. L. Heisler

The Cigar Lake project, located in northern Saskatchewan (Figure 1), is one of the world?s largest high grade uranium deposits, with reserves of 150 million kilograms of uranium in a deposit averaging 430 metres below the surface. The Cigar Lake project is being developed by Cigar Lake Mining Corporation (CLMC) which is owned by Cameco Corporation (48.75%), Cogema Canada (36.375%). Idemitsu Uranium Exploration Canada Ltd. (12.875%) and Korea Electric Power (2%). Mining the Cigar Lake orebody is presenting a very real challenge due to the high grade and the ground conditions in and around the orebody. Presently, an underground test of various mining methods is underway.

Jan 1, 1992

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016