Search Documents

By R. Hogg, P. Bunnaul

Sedimentation in highly, flocculated suspensions of fine particles, such as clays, occurs through individual settling units (flocs) that have very open structures and correspondingly low densities (typically less than 5% solids by volume). Such settling processes rapidly lead to the buildup of a bed of flocs that are essentially close-packed, with an inter-floc porosity of perhaps 50%. However, the overall solids content is no more than about 2% to 3% by volume. Consequently, the thickening process is dominated by the bed consolidation rather than by the simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate, for a given system, that consolidation rates are essentially determined by the solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical, as well as the chemical, conditions of the flocculation process. Furthermore, the extent to which gravity consolidation proceeds depends on the total weight of the sediment (i.e., on the bed height and the solids concentration). The implications with respect to thickener operation and the requirements for the laboratory testing for thickener design are discussed.

Jan 1, 1993

By Peijian Zhang, Yansheng Liu, Yuusaku Tominaga

The directions for ventilation control are often given in linguistic styles such as "if the airflow rate measured is small, a high value of rotation on a local fan should be chosen." In order to control the underground climate using a computer instead of a human being, both the reliability of data values measured underground and the application of human recognition of data values are required. The efficiency of data transmission is dependent on a method of checking a signal which is changed by mixing noises resulting from cases of electrical and mechanical damage to cables. In the study, fuzzy reasoning is adopted to choose a checking method for underground conditions from a normally operating state to an emergency. Fuzzy reasoning is applied to control airflow rate under the linguistic control rules given. It is shown that an effective series of linguistic control rules derived by fuzzy-sets theory is available in ventilation control when used in conjunction with an air velocity sensor, a computer and a local fan with thyristor control. Moreover, a system to make an optimum series of linguistic control rules for ventilation control is introduced.

Jan 1, 1987

By Susan T. Bagley, Linda D. Gratz, Kirby J. Baumgard

The extensive use of heavy-duty diesel engines in underground mines has raised concerns about the potential adverse health effects to miners exposed to diesel particulate matter (DPM) which contains mutagenic and carcinogenic organic compounds. The purpose of this study was to compare the levels of DPM, biological activity, and polynuclear aromatic hydrocarbons (PAH) attributable to diesel engines in underground coal mines and similar data collected in engine laboratory facilities to assess whether laboratory data could be used to predict in-mine levels of diesel emissions. Mean in-mine DPM and SOF concentrations varied from 0.90 to 1.9 mg/m3 and 0.08 to 0.40 mg/m3, respectively. DPM-associated mutagenicity (mean) levels at two of the mines varied from 400 to 970 revertants/m3. Concentations of three PAH differed by up to four-fold between two of the mines, largely reflecting differences in DPM and SOF levels. The laboratory raw exhaust data were divided by 100 to obtain expected or predicted values for in-mine concentrations. The predicted DPM, SOF, mutagenicity, and PAH values based on laboratory samples were not significantly different from many of the in-mine values. Using a potential in-mine dilution ratio range of 20 to 200:1, virtually all in-mine data fell within the predicted range. Therefore, an estimate of in-mine concentrations can be determined by evaluating laboratory data. This will allow for extrapolations from laboratory tests with particulate emission control devices to assess potential health-related benefits due to their in-mine use.

Jan 1, 1991

By Gealy W. Wallwork

The administrative processes of coal mines are becoming increasingly complex. As society evolves into a more complicated structure with greater emphasis on individuality, government regulations reach deeply into every activity in an effort to force individuals into a standardized mold. These contradictory pressures add an extra burden to the administration of a mining operation. Recent years have brought a substantial change in the skills needed by mine supervisors and managers. As a result, a better understanding of the administrative functions is necessary. The mine superintendent has the overall responsibility for the mine; for effective operation he must be sufficiently knowledgeable to oversee all the complex functions that make up the mine. This chapter does not cover all the administrative requirements because of the variation in mine operation and in company policies and organizational structure. It does attempt to identify the administrative functions that would be required at a large mine with a preparation plant. It is assumed that the mine operation is decentralized with very little duplication of functions at the organizational levels above the mine. Thus each function is assumed to be relatively complete at the mine and under the general supervision of the mine superintendent.

Jan 1, 1981

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By W. A. Crosby, A. Bauer

The recent increase in size of open-pit mining operations has resulted in major improvements in efficiency that are beneficial to the mining industry. Higher bench heights, larger diameter blast-holes, and more powerful explosives have played an important part in reducing mining costs. These measures have, however, resulted in increased energy concentrations in the blast area, which can result in severe backbreak problems for final pit walls. If backbreak is not controlled, a decrease in the overall pit slope angle will ultimately be necessary, and consequences, such as decreased recoverable ore reserves and increased waste-to-ore ratios, will result. Greater amounts of loose face rock will be produced, and planned safety berms will be less effective or nonexistent. Hazardous working conditions can also result. Remedial measures, such as scaling large areas and using wire mesh or other artificial support, are very expensive and difficult to implement. There must be a trade-off between the money saved by using larger blasts, and the time spent to maintain pit wall quality. The best approach is to control blasting effects so the inherent strength of pit walls is not destroyed. Presplit and trim blasting are two control blasting techniques used to accomplish this. Both techniques are designed to create a low explosive energy concentration per unit of wall area at the perimeter of the pit. Energy concentration of the main production blast must also be controlled to avoid damaging the final pit wall. A low-energy concentration at the final wall can be obtained by decoupling charges, decking charges, using less powerful explosives, decreasing blasthole diameters, and changing the burden and spacing. Rock properties-fragmentation and the final state of the pit wall-influence the success of a blast. The most important properties to consider are: in situ rock strength, and the nature, frequency, and orientation of structural features. Since these variables cannot be controlled, they must be evaluated by suitable field tests, and then a control blast can be designed using controllable variables, such as spacing, burden, and hole diameter, so the blast will be successful for appropriate rock conditions. One main thrust of this article is to show how control blasts can be successfully designed for larger hole sizes, up to 381-mm-diam. While efforts to produce a good control blast in shovel/truck pits have been ongoing for some time, recent use of a modified presplit technique in dragline operations has helped reduce water problems, improve safety, and increase dragline productivity in a number of surface coal mines. This article presents examples on designing and using presplit and trim blasting for large hole operations in both shovel/truck and dragline mines. Presplit Blasting As introduction to presplit blasting, Fig. 1 illustrates a typical presplit blast layout using 102 mm-diam presplit holes for 381¬mm-diam production holes. For this type of blast, presplit holes would normally be drilled first, ahead of main production holes. The choice can then be made between loading and firing the presplit line or infilling the main blast. In the latter case, the presplit line would be fired instantaneously 100-150 milliseconds before the main blast. As shown in the figure, the presplit line is formed ahead of the main

Jan 2, 1982

The Sandvik Group (Sandvik AB), headquartered in Sandviken, Sweden, continues to expand its worldwide operations growth. After recent acquisitions, including Tamrock, headquartered in Tampere, Finland, the company now has annual sales of more than US$5 billion (SEK 40 billion). With the acquisition of Tamrock, Sandvik has further increased its interests in the mining industry. Sandvik Rock Tools, a familiar name in the mining industry, is one of the world's leading suppliers of rock-drilling tools. And Tamrock is one of the world's leading suppliers of drilling machinery, loaders and equipment for rock-excavation operations. Sandvik believes that the two companies combined offer customers "maximum productivity through total system solutions, including machinery, service and tools." In 1997, Tamrock posted sales of US$940 million (SEK 7.5 billion). In addition to its expertise in drilling tools and equipment, Sandvik is supported by its collective resources in specialty steel and cemented carbide. These resources include extensive research and development capabilities, with annual investments in R&D now at about US$150 million. As a result of the R&D programs, internal expansion and acquisitions, the company has nearly doubled in size during the past four years. From 1994 to 1997, nearly US$1 billion was invested in internal growth and another US$825 million has gone towards acquisitions. Return on net assets is now 22% annually. In addition to Tamrock, acquisitions of interest to the mining community include Drillmaster Inc., Houston, TX. The acquisition of Drillmaster (by Sandvik Rock Tools) has further strengthened Sandvik's position in down-the-hole drilling tools. Other major recent acquisitions by Sandvik include Kanthal, a Swedish manu¬facturer of metal and ceramic-resistant materials for electric heating furnaces, household appliances and elec¬tronics, and Precision Twist Drill, Crystal Lake, IL, one of the leading producers of high-speed cutting tools. With more than 38,000 employees worldwide, the Sandvik Group is divided into six separate business areas. Each area is responsible for its own R&D, production and sales: ? Sandvik Mining and Construction. Including Tamrock and Sandvik Rock Tools, this business area boasts of offering the most comprehensive range of "rock-working" products. These include drilling rigs, loaders, rock-excavation equipment and rock drilling tools. ? Sandvik Specialty Steel. This area includes Sandvik Steel and Kanthal, manufacturers of stainless steel tube, strip wire and bar, as well as high-alloy steel and specialty metals. ? Sandvik Tooling. This business area consists of tools and tooling for metalworking applications. Sandvik Coromant is a market leader in the development, manufacture and marketing of tools using cemented carbide, ceramics and extremely hard materials, such as diamond and cubic nitrite. CTT Tools is the world's largest manufacturer of high-speed steel tools and is now expanding operations into solid cemented-carbide tools. ? Sandvik Hard Materials. This segment produces a full range of "hard materials," ranging from cemented carbide to diamond. This area manufactures and markets a full range of cemented carbide blanks for tool manufacturers, as well as components and rolls. ? Sandvik Saws and Tools. This business area manufactures high-quality handsaws and metal saw blades, as well as hand tools ranging from wrenches to chains for logging machines. ? Sandvik Process Systems. This segment manufactures steel belts, process systems and automatic sorting systems for the chemical

Jan 1, 1998

By Charles H. Grant

Blast design methods generally deal with end points or limits of design such as spacing, burden, stemming depth, etc. Even cratering design deals with limits defined as a function of energy decay to a limit. Although this crater method provides a better method than trial and error judgment it does not take into consideration the distribution of energy throughout the material to be blasted. This paper deals with a method of examining this distribution with the aid of a computer and how changes in blast design affect this distribution. First I would like to explain the equation used to develop the energy summations throughout the blast. As shown in Figure I a series of drill holes are drilled to various depths starting by placing the explosive charge on the surface and then at various depths until a sufficient depth of hole is reached to exceed the ability of the explosive energy effect to reach the surface of the ground. All volumes of explosive are the same, all holes contain the same explosive and the drill hole diameter is the same.

Jan 1, 1980

By Hemendra N. Kalia

The target to double the coal production by 1995 presents a formidable challenge to the coal mining industry. The mines of future, probably will be located in relatively difficult geological environment because of the exhaustion of the well defined bedded and easily minable deposits. To compound the problems of mining industry will be the reliance of power plants need for coal. The coal must reach the power plants on schedule to avoid expensive blackouts and brown¬outs. It will be imperative that the mines operate without interruptions and at designed capacities. The parameters which have been traditionally responsible for the interrup¬tions of production are: breakdown of production machinery, labor management relations and geological anomalies. Of these three problems, solutions for the first two can be arrived at by developing procedures to correct the situation. A planned maintenance and preventive maintenance program will go a long way in minimizing the equipment breakdowns. Labor relations will eventually improve as the miners begin to enjoy long-term employment. However, with the geological problems, the situation will probably continue to deteriorate and would require careful planning to minimize the impact of geological problems on production and safety. Some of the geological aspects which interfere with production are: faults, washouts, slips and slickensides, water bearing overlying strata, impuri¬ties in the coal seam, and presence of expansive clays in the coal floor. The design of large capacity mines will have to incorporate the geological distur¬bances and mine through them it may become very uneconomical to abandon producing sections because of the presence of the geological anomalies. This paper discus¬ses the geological aspects of coal mining which should receive consideration from the inception of the mining ventures. Pertinent geological aspects are discussed to develop the data base which will aid in evolving safe and efficient mine layouts.

Jan 1, 1976

By Ross W. Smith, Xiapeng Zheng, Peggy J. Arps

The adhesion (and de-adhesion) of Bacillus subtilis to dolomite was determined under a number of conditions of initial concentration of the organism, agitation, mineral particle size and temperature. Rate equations curves for both adhesion and de-adhesion were constructed, with the rates of de-adhesion being about half that of adhesion. From the temperature data the energy of adhesion was determined to be about 1.02 kcal/mol. Adhesion of dolomite to B. subtilis follows a Langmuir isotherm. Equilibrium constants, adhesion capacity and Gibbs free energy of adhesion of B. subtilis to dolomite (at pH 6.6) were determined. These values were compared to similar data for adhesion of B. subtilis to apatite and dolomite.

Jan 1, 2002

Cost accounting information is used primarily for (1) planning, control, and performance evaluation; and (2) managerial decision-making. Incremental analysis is a tool for managerial decision-making. It is designed to estimate future financial performance, namely the benefits and costs associated with alternative courses of action. Decisions may be distinguished as pertaining to short-term or long-term activities. Long-term activities frequently focus on capacity decisions and the attendant capital budgeting processes used to quantify the financial effects of these decisions. Short-term decisions typically address short-range production quantity and pricing issues, outsourcing, selection of the optimal mix of products, inventory management, and the acceptance of special orders. This chapter addresses these short-term decisions.

Jan 1, 1999

By Catherine M. Dentan, Yosry A. Attia

The presence of finely divided carbonaceous matter, particularly graphite, in gold ores, adversely affects the adsorption - recovery of gold by activated carbon from cyanide solutions of such ores. Competitive adsorption of gold by graphite and other carbonaceous matter, is thought to be responsible for this deleterious effect In this study, adsorption of gold cyanide complex AU(CN)2- by the activated carbon used in carbon-in- pulp or carbon-in-leach processes, was compared with that by graphite which was chosen to represent the carbonaceous matter. Similar adsorption studies were made with gold chloride complex AuC14-. Correlation of adsorption with surface characteristics and thermodynamics were presented in detail, and a flowsheet for graphite-in-leach was proposed.

Jan 1, 1990

By Eugene E. Hively

The Tower Kill is a vertical "stirred" ball/pebble mill recently introduced in the Western Hemisphere. This device offers a significant power savings on wet fine grinding applications when compared to conventional tumbling mills. This paper describes the laboratory application of this mill wet grinding hydrated alumina to products of 50 percent passing 2 to 6 microns.

Jan 1, 1983

By J. B. Stockton, D. J. Robbins, E. T. Woodburn

Batch flotation data in an equilibrium cell show that beneficiation improves with froth drainage. The limiting lamella thickness in a well- drained 3-phase coal froth appears to be determined for ultra-fine particles (-45µm) by the d90 particle size. The froth stability is considered to depend on the existence of a very thin liquid film between the outer surfaces of the d90 particles and the bounding bubble interfaces of the lamella in which the particle is held. The dependence of the coalescence rate of bubbles in these froths on the residual surfactant concentration in the lamella liquid is then consistent with stability analyses for two-phase foams.

Jan 1, 1988

By Jacques Deraisme

Geostatistics has been applied in many mining feasibility studies throughout the world during the last decade. Recently geostatistics has begun to be applied to the field of mining processes by attempting to aid in the definition of the best mining policy. For a feasibility study the grade-tonnage relationships give a reasonable order of magnitude estimate of the ore reserves within the deposit. But the reserves that will actually be recovered, will vary depending upon the mining methods and the technical means used. The profit earning capacity of the mining project is determined by a great many factors, such as for instance: accessibility of reserves to extracting machines, the haulage distance between the mine and the mill, the variability of produced ore (tonnage and grades) which could necessitate stockpiles or blending areas?

Jan 1, 1979

By N. J. Peberdy, C. N. Moreton, K. C. Garner

Introduction During the past decade a major objective of the process industry has been to use digital computer technology to improve plant operating efficiencies. This objective implied some form of optimization, a concept that has various interpretations depending on the view of the prospective user. For the purpose of this paper, optimization of a process plant is defined as the establishment and setting of plant operating conditions that maximize some mathematical yield function, i.e. maximum profit, minimum residue, etc. Analysis of these objectives and the available design and implementation techniques led to the conclusion that digital computer and optimization techniques are not the stumbling blocks, but rather the development and derivation of the mathematical models of the unit operations and process plants to be optimized. Such models should not only describe the optimized (steady-state) objective, but also how one steers to this state (control algorithm). Due to the multidisciplinary nature of the skills associated with the design and operation of process plants, the development of suitable models by a single discipline, such as the process control engineer, was found to be not only difficult but often impossible, due to budget and human resource limitations. To over-come these limitations, a computer aided design (CAD) tool has been developed. It aims to provide a productivity tool to the various disciplines, at the same time coordinating the technical input from each. The system described is but the starting point in an evolutionary development of a tool that, with use, is becoming more efficient and cost effective to use. Development has become an application engineering activity rather than the preserve of the computer specialist. Project phasing The development of a mathematical description of a process plant requires coordination of information from conceptual design to operation management. The activities required to build and operate a process plant are divided into four basic chronological activities or phases. These activities are often undertaken by different organizations and disciplines. As a result, continuity is often lost with the resultant loss of critical design data. The major activities are considered to be: conceptual and flowsheeting; detailing around the P & ID; building and commissioning; and plant operation. The CAD system described provides a design tool to be used for each of these activities, as well as providing continuity between the activities and the disciplines involved. The heart of the system is the dynamic simulation of the flowsheet. Each of the activities will be discussed, leading to two simple examples that demonstrate the use of the simulator. Figure 1 shows a schematic format of the various activities and the path followed by the dynamic flowsheet simulator in the life of a project. Flowsheet development The prime requirements in the design and develop¬ment of a process flowsheet are • selection of the correct unit operations to achieve the most economic (capital and operating) beneficiation of the specified reserve ; • the sizing of the unit operations to achieve the desired results, as a function of the projected feed rates etc., to handle the time related (dynamics) of the process; and • the production of a set of engineering documents showing the drawn and labeled flowsheet with an equipment list and process specification for each of the unit operations. The question may well be asked at this stage why dynamic flowsheet simulation should be considered when steady state modeling has been found to be adequate to date. With the increases encountered in the cost of capital, one often cannot afford the luxury of designing around the compounding worst case technique. Further, a more accurate design of the control surges can be achieved. No information is lost in that the steady state solution is in fact a subset of the dynamic model. In generalized state space modeling, the differential equations describing the process dynamics are illustrated in the following matrix notation: XDOT=A.X+B.U(1) Y =C.X+D.U(2) where XDOT describes the set of first order derivatives of the system state Vector, and X- is the system state Vector; A - is the system matrix operator which in the general nonlinear case is both a function of X and time ; U- is the process input vector; B - is the input mapping matrix; Y - is the set of observations; C - is the output mapping matrix which maps X - onto Y; and D- maps the input onto the observations. Thus, by time integration of the system dynamic equations, described in (1), the dynamic trajectory away from any set of initial conditions can be deter¬mined. Further, by finding the conditions at which XDOT = 0, the steady state solution can be determined.

Jan 1, 1987

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1987

Conveyor belting-Dunlop Belting Division has published a manual on its Starflex plied conveyor belting. The design section of the manual contains advice on the calculation of tensile strength and horsepower needs while the section on belt selection offers helpful recommendations. Circle 200 on reader service card Hydrostroke feeders-A pamphlet from Kone Corp. highlights the uses and operating principles of its hydrostroke feeders. Circle 201 on reader service card Electric cylinders-A 24-page catalog from Raco International Inc. describes applications for its electric linear actuators in addition to the electronic options for computer - controlled operation. Circle 202 on reader service card High torque drives-T. B. Wood's Sons Co. offers a 56-page booklet providing features and specifications on its high torque drives. Information includes a step-by-step drive selection proce¬dure. (HTD) Circle 203 on reader service card Sludge depth meter-The model 600 sludge-depth meter that locates the sludge bed in clarifiers and settling tanks is described in a four-page bro¬chure from Markland Specialty Engineering Ltd. (600-84) Circle 204 on reader service card Cavity pumps-An eight-page bulletin is available from Robbins & Myers Inc. It features the application of Moyno progressing cavity pumps in handling composite slurry fuels. (400) Circle 205 on reader service card Roller chain-A roller chain catalog shows heavy duty drive chains and other specialty conveyor chains. It is available from Peer Chain Co. (PC200) Circle 206 on reader service card Belt filter-Phoenix Process Equipment Co. has available a pamphlet detailing its belt filter press. The unit is designed to dewater refuse and clean coal, yielding easily handled dry filter cakes. Circle 207 on reader service card Capabilities - Literature from International Mineral Services Ltd. highlights its services and capabilities to the mining industry. Circle 208 on reader service card Motor analysis - How to select the proper electric motor by comparing life cycle costs, power costs, rate of return, and other factors, is described in a brochure from Westinghouse Electric Corp. (SA-11376) Circle 209 on reader service card Cavity pumps - A product application data sheet is available from Robbins & Myers Inc. It details the use of Moyno positive-displacement, progressing cavity pumps in handling ground limestone slurry. (PC-21) Circle 210 on reader service card Dust collectors - "Dust Collector Selection Guide," from American Air Filter, describes dry mechanical collectors, wet collectors, fabric collectors, and electrostatic precipitators. (CAD-1-901G) Circle 211 on reader service card Wet scrubber - A 12-page bulletin from The Ceilcote Co. provides a comprehensive description of its ionizing, wet-scrubber system. (12-19) Circle 212 on reader service card Metric o-rings-Simrit Corp. has published a 16-page brochure detailing its full line of standard metric o-rings. Information includes graphics and dimensional charts, and specific data on materials and application ranges. Circle 213 on reader service card Hearing protection - A 16-page catalog from Cabot Corp., EAR Division, provides information on its hearing protection devices and noise control products. Circle 214 on reader service card Toxic gas detection - Sensidyne Inc. is offering a guide for toxic gas monitoring. A description of the electrochemical sensors, as well as ranges, complete specifications, and interference charts are included. Circle 215 on reader service card Hydraulic bolting systems - Ingersoll-Rand Co. is offering a brochure on its line of hydraulic bolting systems. These systems, hydraulic wrench and power console, are designed for heavy duty bolting applications. Circle 216 on reader service card Temperature monitoring - A brochure describing the Ramsey Engineering Co.'s micromonitor temperature monitoring system is available. Three types of switches are available for monitoring bearing temperatures. (80.300) Circle 217 on reader service card Product catalog - Shadbolt & Boyd Co. has published a product catalog. Among items described are hoist slings and cranes; compressors; hydraulics; wire rope, chains, and fittings; and materials handling and shop equipment. Circle 218 on reader service card Cylinder controls - A 12-page booklet presenting Hanna Corp.'s line of electrical controls for cylinders is available. It features proximity and limit switches for hydraulic and pneumatic cylinders, and standard and 3-amp reed switches for pneumatic cylinders only. (550) Circle 219 on reader service card Slurry pump - Pettibone Corp. has published a 24-page booklet covering its heavy duty pumps made with 'diamond alloy' materials for handling slurries of abrasive materials. Circle 220 on reader service card

Jan 9, 1985

By Slavko Ostojic, V. G. Hill

This paper reviews various bauxite classification schemes with respect to the differences in texture, composition and geological associations of the deposits. It demonstrates that a techno-economic classification, based on: a) associated rock type - lateritic versus karstic, b) content of aluminum ore minerals - gibbsite, boehmite and diaspore, and c) gangue minerals (iron oxides etc.) has a geological basis with natural cut-off points for the bauxite types identified. Thus, this scheme is seen as applicable to bauxite resources. It also provides a basis for their rational exploitation taking into consideration the long-term interests of both the bauxite producing and consuming countries. Against this background, the industrial mineral or non-metallurgical grades of bauxite are seen as localised and relatively rare occurrences. Their consumption should, therefore, be aimed toward the specific (hence more remunerative) products as indicated by the bauxite characteristics.

Jan 1, 1984

By J. R. Stoltz, E. Thompson, S. Pattee

On May 15 and 16, 1999, a mine ventilation survey was performed in the 705-m- (2,312-ft-) deep Cayuga Mine, Cargill Salt Division, Lansing, NY. The purpose of the survey was to develop a numerical model of the existing ventilation system and to perform a computer simulation study for long-term environmental and ventilation planning. Because the natural ventilation pressure (NVP) has significant effects on the ventilation system at the Cayuga Mine, there was a need to assess the NVP acting in the mine. Due to the ventilation arrangements in the Cayuga Mine, the authors decided to use the direct-measuring method to determine the NVP by measuring differential pressure across the automatic fan door. This difference in pressure was measured immediately after the fan was stopped and the automatic door was closed to stop the flow throughout the entire mine. To show seasonal changes in NVP, two additional measurement for NVP were performed, one on Aug. 22, 1999, during the hot (summer) season, and another on Feb. 6, 2000, during the cold (winter) season. The mutual interaction between the natural ventilation pressure and the main fan at the Cayuga Mine is also discussed

Jan 1, 2003