Search Documents

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By G. A. Gamble

Fans used to ventilate subway, passenger rail and vehicular tunnels are similar to the fans used to ventilate underground mines. However, tunnel ventilation fan systems are typically designed to meet NFPA 130 or 502 standards, while mine ventilation fan systems must comply with the appropriate federal mine safety regulations. As a result, fan operation requirements and performance criteria, as well as typical fan and duct configurations differ significantly for tunnel and mine ventilation applications. Variations in environmental conditions in tunnels as compared to mines also result in differences in fan performance and material specifications. The need to enclose tunnel fans within building structures creates space restrictions impacting fan size selection that are not commonly encountered in mine fan installations, resulting in different approaches to selecting fans for the two types of tunnels. This paper discusses the various similarities and differences in design considerations for tunnel and mine ventilation fans.

Jan 1, 2009

By R. Bokotko, J. D. Miller, J. Hupka

Laboratory results from an initial study on the removal of SO2 from gas mixtures are reported using air-sparged hydrocyclone (ASH) technology. Tap water and alkaline solutions were used for absorption and the influence of gas flow rate, water flow rate and length of the ASH unit were investigated. Complete removal of SO2 was possible with very favorable kinetics. The efficiency of sulfur dioxide absorption from air using the ASH is compared with the efficiency of conventional technology.

Jan 1, 2002

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002

By William R. Yernberg

What a difference a year makes. One year ago, the iron mining industry and the steelmaking industry in the United States were in trouble. Many companies were in bankruptcy, and talk of plant and mine shutdowns was rampant. At that time, it seemed difficult, if not impossible, to remain competitive with imported steel. In addition, the World Trade Organization declared as illegal the tariffs placed on imported steel. And many questioned the viability of the ironmining and steel industry in the United States. At that time, global economic conditions were the main contributors to the industry’s problems. However, since last year’s meeting, changes in global economics have actually helped the steel industry in the United States. Heavy global demand for steel has caused raw-material shortages worldwide. Much of the increased demand is a result of the economic boom in China. In addition, because of a weak U.S. dollar and higher international freight rates, steel imports into the United States have been reduced to about 50 percent of recent levels. These factors have contributed to a rebirth of the U.S. iron mining and steel industries.

Jan 1, 2004

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007

By B. Cousins

Copper, nickel, zinc and other ?penalty? metals are found with gold together in nature, and have a similar chemical affinity for cyanide used in leaching operations4. As a result, solutions that come from the heap leach pads contain a significant concentration of penalty metals along with the desired gold. In solution, gold and cyanide form the complex Au(CN)2- that is readily adsorbed onto activated carbon. Penalty metals as individual metal ions also load onto activated carbon and, depending on the concentration of cyanide and the pH of the solution, can form various cyanide complexes. Some of these complexes can also load onto carbon while some are significantly inhibited from loading. Copper, for example, can form the dicyanide complex Cu(CN)2-, the tricyanide complex Cu(CN)32-, and the tetracyanide complex Cu(CN)43-. At a low pH and a low concentration of cyanide, the dicyanide complex predominates. At a higher pH and a higher concentration of cyanide, the tetracyanide complex predominates. Without excess cyanide, however, individual copper ions can remain present. Activated carbon is used in gold extraction because it is highly selective for gold and less so for other metals, such as copper3. However, copper has the ability to adsorb (?load?) onto activated carbon and block the adsorption of gold when it is in the dicyanide form and in a high enough concentration. When copper is in the tetracyanide form, copper loading is significantly inhibited, allowing for the maximum gold recovery. In order to ensure the tetracyanide complex is formed, a combination of both available cyanide and elevated pH must be present. In the South Area of Newmont Mining Corporation?s Gold Quarry mine in Carlin, Nevada, copper and nickel loading becomes a problem when certain acid generating zones of the heap are leached. Copper, nickel, zinc and other penalty metals become leachable and the lower pH uses up more of the cyanide and creates carbon loading conditions for the metals. This decreases the carbon?s ability to extract the gold from solution, decreasing the recovery and increasing the concentration of gold in the barren solution that leaves the carbon columns. In this study, operational data from March through to May of 2007 is presented to show how Newmont developed a quick fix to lower pH and elevated metal concentrations that were causing low gold loadings on activated carbon at their South Area Leach (SAL) heap leach operations. Laboratory tested were also conducted to examine the chemical kinetics of metal loading and the individual effects of increased cyanide concentrations. THEORY Copper I ions form four different complexes with cyanide in solution: the monocyanide species CuCN, the dicyanide species Cu(CN)2-, the tricyanide species Cu(CN)32-, and the tetracyanide species Cu(CN)43-. The species are formed from the following reactions: [Cu)(?+-+ K1 (1) Cu ß2 (2) --+?+23)(3CNCuCNCu ß3 (3) --+?+34)(4CNCuCNCu ß4 (4) ] where K1 equals 1019.50, ß2 equals 1024.03, ß3 equals 1028.65, and ß4 equals 1030.35. Along with these complexing reactions, hydrogen cyanide and water also dissociate in solution, as per the following reactions: [H?+-+ KH (5) OHOHH2?+-+ KW (6)] where KH has a value of 109.24 and KW has a 1014 value2. These six chemical equations compete with each other, with domination of one over the others dependent on the CN- and H+ concentrations. Each complex also has different properties when it comes to its loading behavior on activated carbon. The dicyanide copper complex and the monocyanide copper complex have an affinity for adsorption onto activated carbon that is greater than the affinity of gold cyanide for adsorption. They also have a lower solubility in water, which enhances adsorption. The tricyanide copper complex and the tetracyanide copper complex are water soluble and have an affinity for loading adsorption on activated carbon that is less than the affinity of gold cyanide for loading adsorption1. There are three prime reasons for this phenomenon. First, the extra cyanides mask the metal ion more, which blocks the main adsorption characteristic of the complex. Second, the complexes are also larger, making it harder to physically fit into the active sites on the carbon. This helps make the latter two complexes kinetically inhibited from adsorption, freeing carbon active site to load with gold cyanide complexes. Third, it is also important to consider the expressions of the mass and charge balance. These balances describe all the overall concentration of copper and cyanide in solution, as well as marking overall charges of the ions in solution4. This is important because significantly changing the charge from positive/neutral to more negative is another reason for activated carbon to reject adsorbing the higher cyanide complexes. The speciation of copper and other penalty metal cyanide complexes in solution is dependent on the pH. At lower pH values, increased hydrogen ions (H+) can out-compete metals for cyanide ions. Lower free cyanide in the system leads to the lower cyanide species of copper cyanide predominating, with a noticeable concentration of the free metal, monocyanide and dicyanide species of copper cyanide. At higher pH values, hydrogen ions are significantly reduced, reducing the kinetics of HCN formation. More free cyanide remains in the system, allowing for more complexing. With this higher amount of cyanide in the system, the tetracyanide species of copper cyanide predominates, also with a noticeable concentration of the tricyanide species of copper cyanide. Higher copper concentrations, however, require more

Jan 1, 2009

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By Juan P. Camus

Mining is one of the oldest industrial activities. Its products are essential to modern civilization. Paradoxically, and despite a deep-rooted belief to the contrary, mining is not a lucrative industry— at least not in the aggregate. This assertion is true not only for recent years, one of the weakest periods in terms of metal prices, but also for a long time past. In 1776,Adam Smith said in The Wealth of Nations: “Of all those expensive and uncertain projects, how-ever, which bring bankruptcy upon the greater part of the people who engage in them, there is none perhaps more perfectly ruinous than the search after ... mines. It is perhaps the most disadvantageous lottery in the world... Projects of mining, instead of replacing the capital employed in them, ... commonly absorb both capital and profits.”

Jan 1, 2002

By Don F. Macfarlane

This paper describes the field application of the NTH fracture classification to rock encountered in the construction of the 9.6 km long, 10m diameter, Second Manapouri Tailrace Tunnel. Excavation of the tunnel was undertaken by TBM between 1997 and 2002, in gneisses, granitic and diorite rocks. The paper outlines an adaptation of the NTH fracture classification used during the geological logging of this tunnel. The NTH fracture classification was primarily applied to assess discontinuity spacing for tunnel support requirement decision-making. The paper includes some general comparison of NTH classes with overall penetration rate.

Jan 1, 2008

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Russell Miller, Fun-Den Wang

High Pressure Water Jet Assisted Tunneling The high pressure water jet assisted tunneling project was conducted in a granite quarry near Skykomish, Washington, approximately 90 miles east of Seattle. A 7-ft diam tunnel boring machine was modified and equipped with high pressure water jets. The concept that tunneling rates can be improved by using high pressure water jets was validated, with an average increased advance rate of 50% to 60%. For some tests, the advance rate was more than doubled. A comprehensive economic analysis has shown that very significant savings are possible. At a 50% increase in advance rate, cost savings of 14% and 24% were projected for 10-ft and 20-ft diam tunnels respectively. These benefits were seen to be relatively insensitive to water jet equipment costs.

Jan 1, 1976

By Rolland R. Mates

This paper describes the use of post- tensioned rock anchors to reduce the risk of future damage to a residential structure as a result of coal mine subsidence. The project described in this paper was performed by the Office of Surface Mining Reclamation and Enforcement (OSMRE) of the U. S. Department of the Interior. The OSMRE was created to administer Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. The responsibilities of OSMRE include "reclamation and restoration of land and water resources, adversely affected by past coal mining including prevention, abatement, control of coal mine subsidence. ?('l) Consequently, OSMRE has been addressing mine subsidence problems since its initial subsidence stabilization project in 1979. Stabilization activities have primarily consisted of supporting the overburden material by injecting materials through drilled bore holes into the underground mine voids. Injection of various materials into mine voids, including fly ash mixtures, coal refuse, cement grout, and gravel has proven to be a successful method of reducing mine subsidence-related surface movements, and has been extensively utilized in mitigating mine subsidence problems. However, the cost of drilling for injection can be extremely high in areas where the depth to the coal seam is great.

Jan 1, 1986

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011

By Joseph J. Zaluski, J. Steven Gardner, Marco M. Rajkovich

The telephone rings at 3:20 a.m. An exasperated voice on the other end says, “There has been a mine explosion at Mine No. 5 and we have not heard from three units of men.” Twenty-three minutes later, the phone rings again and another panicked voice says, “There is something wrong at the slurry impoundment, the pool level has just dropped five feet and we are trying to figure out what is wrong” Thirty minutes later, the mobile phone rings. An excited security guard says, “We have reports of thick black water running down the right fork and left fork of Straight Creek and both seem to be rising in the banks.” If this is not enough excitement, the mobile phone rings again. A stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Co. No. 2 Mine, which is adjacent to our No. 5 Mine.” Is this all some kind of dream or nightmare? More importantly, though, if this happens, what do you do? Most people think: “It can’t happen to me.” But mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. A mine’s response must be quick, cool-headed, calculated and effective. This article examines the issues, concerns and ramifications of this hypothetical disaster. The authors then present a systematic crisis-management response.

Jan 1, 2004

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

By K. Oraee

Mining of copper ore and the related industries play an important role in Iran?s economy. Copper ore production in Iran accounts for 75% of the total production in the Middle East. All activities related to copper, that is, exploration, production, refinement etc are owned and managed by state owned companies. Decisions have been made to privatize all these activities. To assess the success of this privatization process, different components of the industry must be subject to economic analysis. In this paper, the cost estimation of all operations has been carried out. The total potential and attainable revenues have also been estimated using historical data available from the industry. Risk is a major factor in all mining activities and the copper industry of Iran has been subject to risk factors arising from many internal and external variables. These variables have been recognized and their effects evaluated. The effect of risk on the economic feasibility of the operations in the industry has also been analyzed.

Jan 1, 2011

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008