Search Documents

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry as a tool to improve the efficiency of its processes, to reduce costs, but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios: lower ore grades, extreme weather conditions, deeper deposits, harder rock mass, and high-stress environments. This paper discusses the importance of innovation for the mining industry and describes the mechanisms by which it is carried out. It includes a review of the drivers and actors involved and current trends. The digital transformation process that the industry is going through is analyzed, along with other relevant trends that are likely to shape the mining of the future. Additionally, a case study is presented to illustrate the technical and economic implications of developing a disruptive innovation project.

Jul 23, 2020

By M. J. Hrebar

In the summer of 1990, a study was conducted to document large tractor (i.e., Caterpillar Dl1N) utilization in surface coal mining. The tractors were found to be utilized as primary production machines and in combination systems with blast casting and draglines and blast casting and excavator/truck systems. In addition, dozers were used to prebench ahead of a primary dragline system. The study also established ranges and averages for Dl1N operating costs and mechanical availability. Based on simulated production of various tractor dozing applications, the potential for low cost coal stripping was suggested (Hrebar, 1991). A follow-up study, also funded by Caterpillar Inc., was conducted in the summer of 1991 to determine actual production rates in two dozer stripping applications. These actual production rates would then serve as a foundation for estimates of stripping costs. This paper presents the results of the studies in a contour and a cast application.

Jan 1, 1992

By Rihab Guellala

In Tunisia, the Paleocene-Eocene series has an important socio-economic interest. It contains profitable oil and water accumulations. Moreover, it encompasses phosphate reserves. The present study uses seismic reflection prospection and borehole data for the reconstitution of the Paleocene-Eocene deposit structure in the Jerid area (southwestern Tunisia), a crucial step for the phosphate exploitation. Firstly, lithostratigraphic correlations incorporating water and petroleum wells were established according to different directions for a tentative approximation of the Paleocene- Eocene deposit geometry by following their lateral evolution. To give more details, seismic reflection profiles were interpreted in the second step. The Paleocene-Eocene formations were associated with their corresponding reflectors on the closest seismic profile using the relation of time and depth in petroleum wells. Analysis of lithostratigraphic correlations shows notable variations in the Paleocene-Eocene series thickness and depth. Seismic profile interpretation explains these variations by highlighting different buried tectonic features. The results confrontation reveals that the phosphatic deposit geometry in the Jerid area is mainly influenced by the (1) emergence of the Saharan platform and the Chott northern chain since the Late Cretaceous, (2) syn-sedimentary normal activity of E-W and NE-SW faults during the Paleocene-Eocene epoch, (3) reverse-reactivation of these faults, and (4) major Tortonian folding phase. This study can enormously enhance the Jerid area socio-economic development by presenting useful findings that may orientate the phosphate exploration.

Aug 15, 2021

By Peter Riba

Up until ten years ago the industry had arrived at a relatively conventional, and consistent design of coke ovens. Through the years the designers and builders were not being heavily taxed to come up with revolutionary new designs. However, the stimulus for design change was ever present. These stimuli for change are quite important and they are the driving force which produce improvements. The most obvious stimulus to change a design is commercial. To "build a better mouse trap and the world will beat a path to your door" is the well used cliche which best befits this philosophy. As in all businesses, coke oven designs require that all of the considerations, which affect the cost or the desirability of the design, be optimized. One way to increase the desirability of the particular design, 1s to make the design in- expensive to operate. Or, put another way, to increase production for the same operating cost

Jan 1, 1980

By Bob Rautenberg, Luminita Calin

The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, was developed by the Metropolitan Water Reclamation District of Greater Chicago as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer overflows. With only one contract left before completion of the Phase I tunnels—the 12.4 km(7.7 mi.) long Little Calumet leg—the pollution control phase of the 175.7 km(109.2 mi.) long system will be 93% complete, once the Torrence Avenue tunnel project comes to an end. This paper describes the Torrence Avenue tunnel project, currently under construction by the joint venture of Kenny (Sponsor) / Kiewit / Shea. Mining of the10.4 km (34,151 feet) long and 8.3 m (27'-4") diameter mainline tunnel was completed in a record thirty-one-weeks period and the concrete lining is nearing completion. Details on the complete muck handling system, numerous mining and concrete lining records will be given.

Jan 1, 2001

By Jr. Goller

You and I can visit cement plants, inspect the various rotary kiln systems and find some equipment or some burning techniques that waste energy--fuel and power. After we have made such a visit and studied a few ideas, we could recommend ways to eliminate much of this waste. Probably every idea would cost money to bring into action. For our discussion, let us arbitrarily set an upper limit of $1,000,000 on the recommendations that we are allowed to make. Call these "low-cost" or "short-term" measures. They are improvements that do not require more than say, three months to complete; they do not require a major revision to the process. Other recommendations are "high-cost" or "long-term"; they are outside the scope of this discussion. Some of our "low-cost" recommendations would offer a satisfactory return on the money that they cost; the remainder would not. Now, is there some way that we can rather quickly pick out the "low-cost" measures that will show a satisfactory return and spend our time making these improvements first? Can we separate these items from those where the return is less likely to be good? I feel that we can pick some of these items quickly if we have a kiln system that has consistently non-uniform day-to-day operation. If the operation is uniform we probably cannot pick them quickly.

Jan 1, 1977

By Doug Halbe

A number of CIP plants have been built in Western Australia in the past two years. The authors have surveyed several of these new plants and present drawings, data and discussion of operating and design innovations and areas of interest.

Jan 1, 1982

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By Charles T. Steuart

The Arkansas Novaculite of Devonian and Mississippian age is the most distinctive formation in the central Ouachita Mountains of Arkansas from the standpoint of both topography and lithology. The formation typically forms precipitous, narrow ridges (hogbacks) which reflect the steepness of dip and the resistance and thickness of the rock units. The Arkansas Novaculite varies from less than 200 feet thick in the north to locally over 800 feet thick in the south and outcrops over an east-west distance of 360 km (200 miles) in the Ouachita Mountains of Arkansas and Oklahoma. Most of the rocks of the formation are highly siliceous with novaculite predominating, and lesser quantities of chert, siliceous shale, conglomerate and rarely sandstone. Novaculite is commonly defined as a homogeneous mostly white rock, translucent on thin edges with a dull to waxy luster and composed almost entirely of microcrystalline quartz. The word novaculite comes from the Latin word novacula, meaning razor hone. This term was first used by Richard Kirwan in his mineralogy text of 1784. The origin of novaculite remains controversial but we believe it was a primary silica derived mostly from the alteration of submarine volcanic-rich materials, with numerous fine biogenic components and some minor clastics (derived mostly from foreland facies via turbidity currents) and deposited as an amorphous siliceous ooze in the deep Ouachita trough. It was subsequently converted to microcrystalline quartz during diagenesis by the compaction of the overlying rocks and the intense Late Paleozoic Ouachita Mountain tectonism. In the central and southern portions of the region three divisions of the formation have been defined: a Lower Division predominantly of light-colored novaculite; a Middle Division of interbedded dark chert and shale; and an Upper Division of massive often calcareous novaculite. In the northern exposures the formation is thinner and contains more black chert and shale, chert-shale conglom¬erate, sandstone and less novaculite. The massive novaculite of the Upper and Lower Divisions is a source of high purity silica (99+%). Indians were the first to use novaculite. They made their various tools and hunting implements from the weathered broken rock until they learned the quarrying techniques. The first white men in the area recognized the use of novaculite for sharpening their tools and knives: previously whetstones were obtained in small quantities from Europe. To this day whetstone is quarried mostly in areas which the Indians and possibly the Spanish previously worked. Some of the current mining practices have changed very little from those of the early quarryman. In areas where the novaculite of the Upper Division is poorly cemented, this friable tripolitic material has found applications in such uses as an abrasive, as a filler or extender in paints, plastics and other purposes. Some of the dense novaculite is suitable as a filler in fire bricks and also in plastics. Because some of it has the tendency to decrepitate when heated not all novaculite can be used for these applications. Several quarry operators are crushing novaculite for road, concrete, and other aggregate. This use was formerly rather limited due to the abrasiveness of the novaculite on crushing and screening equipment. Further potential uses of novaculite are speculative but include application of high purity silica in the production of silicon metal for solar cells, seed or "growing", and fusing quartz for electronics.

Jan 1, 1985

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese (Mn) ferroalloys are chiefly consumed in the steelmaking process as a deoxidizing agent or as an alloying element to produce high-quality steels. These alloys are typically produced in a submerged arc furnace using coke, fluxes and manganese ores of a specific manganese/Fe (Mn/Fe) ratio. Preferred-grade manganese ores should have Mn content greater than 46 percent and Mn/Fe content greater than 5 to produce commercial-grade, high-carbon ferromanganese [1]. Selective mining of high-grade Mn resources has created a scarcity of these resources, which is emerging as a major challenge for the manganese and steel industry. Manganese ore resources are mainly distributed in South Africa, with about 32 percent; Ukraine, with about 17 percent; Australia, with about 17 percent; and Brazil, India, China, Gabon and Mexico, with lesser amounts.

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By G. A. Munoz

Gold leaching of an auriferous pyrite ore from the Portovelo deposit in Ecuador indicates that noncyanide leaching systems, such as thiocyanate and thiourea, are not as effective as the traditional cyanide system. For example, whereas approximately 95% of the gold can be leached from the ore with cyanide, only about 50% gold dissolution can be achieved with a thiocyanate leaching system. Electrochemical measurements indicate that gold is not cathodically protected by pyrite in these systems. Based on the results of preliminary diagnostic experiments, it appears that gold dissolution in thiocyanate and thiourea systems is limited by passivation due to the formation of either elemental sulfur or sulfur compounds on the gold surface.

Jan 1, 1999

By G. H. K. Pearse

Long range transport of pollutants, particularly of sulphur dioxide and the associated acidic precipitation, has received much attention in the press and in international discussion during the last few years. Studies revealing increasing acidity of lakes and the dying out of fish populations over broad regions of the eastern half of North America have created alarm. In this paper, I will not attempt a description of the acid rain phenomenon. For this r recommend the balanced treatment of the subject by Gene Likens et al (1979) in Scientific Americana For my purposes I accept that the problem is serious and direct my attention to exploring a solution. Ultimately, the key lies in the answer to the question; "What do we do with the enormous tonnages of pollution abatement byproducts, chiefly sulphur compounds, that would arise from pollution control?"' Little thought has been given to this most limiting factor to environmental clean-up. This is symptomatic of a basic flaw in the [philosphy] that under-ins environmental policy. Although this paper is to propose a solution to the abatement byproduct problem, the basic flaw - the firmly entrenched, universally adopted, 'polluter pays [philosphy] as it is currently [understood] - needs some comment.

Jan 1, 1981

By Anastasia Xenaki, Edmundo Laporte, Antonio Nieto, Jesus Castillo Gomez, Oscar Velasquez

It is particularly challenging for the mining industry to create and implement an efficient and adaptable mining innovation model to secure the continuous improvement of processes and products via technology. Human resource departments must play a vital role in shifting the mining culture, enabling these new classes of digitally skilled professionals to manage the mining operations of the future. This paper proposes the implementation of a concept based on the 5S mining innovation model ((a) Nieto, 2019), in a coal mining project in Central Asia, Mongolia. Practical and empirical evidence suggests that the model could serve as a roadmap to developing technologies and methods for the mines of the future.

Feb 1, 2023

By David B. Brooks, Roger L. Williams

Control of the environment is as old as mining. Engineers have always had to consider how best to deal with the surface, and the character of the surface environment always affects mining method in some way. However, if the relationship of the mine to the environment is old, today's approach is new. For one thing, land, air and water formerly could be viewed simply as obstacles to be overcome or resources to be utilized to win ore at the lowest possible cost. Now we have come to realize that these nonmineral components of the environment also are highly valuable. For another thing, environ- mental protection has become a public policy issue. Again, a special public interest in land and land use is old. From the firs(, the crown claimed extra rights in valuable minerals, and to this day a multitude of laws and regulations control-and tax-land use in every country. What is new is the detailed public attention bring given to waste management practices, whether these wastes be in the form of solids, liquids or gases, and regardless of where in the environment they appear. (It is convenient to lump all mining environmental problems, including hank fires and subsidence, together under the term "waste management," for in effect that is what they are.) As a result of these changes, the mining engineer must consider that lie is dealing with two productive resources the minerals and the remainder of the environment-and he must expect that lie will be judged not only on his efficiency in recovering the one but also on his effectiveness in protecting the other. Further, in seeking to protect the environment, the modern mining-environmental engineer has a dual role. First, there is the obvious task of finding better ways for industry to cope with waste-management problems in actual operations. Second, there is the less obvious but equally important task of helping formulate appropriate public policy objectives for the environment. Throughout; the section it is assumed that mining is an acceptable land use for the tracts under consideration. The question of whether mining will be permitted at all on these tracts is a further public-policy issue, ultimately to be resolved politically and thus, since it is beyond the scope of engineering, is not a subject that can be usefully discussed in a mining handbook. Finally, none of the statements in the section are predicated on the assumption that required waste-management measures will be privately profitable in the conventional sense. Indeed, the reverse is more likely to be the case-at least if accounts are kept so as to include all appreciable costs and a normal rate of return on investment in waste-disposal and reclamation equipment.',',' However, it is clear that improved waste management will be required of mining firms and that, to a considerable although undetermined degree, this expenditure is in the best long-run interest of both public and industry. The several studies that have attempted to quantify the impact of mining on the environment are admittedly rough but still provide enough information to indicate that there is a big job to be done. For example, something approaching 7,000 mi of stream in Appalachia alone are continuously or significantly affected

Jan 1, 1973

By William B. Schmidt

In July of 1974 a study team comprised of the authors was formed by the Department of the Interior. It was supported in part by funding from the National Science Foundation. The purpose of this study group was to visit coal mines and research and manufacturing facilities in England and Germany, to review the status of mining in these countries, and to identify mining technology which might have application to U. S. mining conditions. The duration of the visit was 18 days. The first week of the trip was spent in England. Time does not permit a complete recitation of the team's impressions but a few of the more interesting technologic developments will be discussed. These fall into the following categories- High Speed Development Ground Support Chainless Haulage and Face Conveyors Nucleonic Steering of Shearers Miscellaneous

Jan 1, 1975

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By G. W. Heunisch

G.A. Carmody and L.B. Anderson We wish to comment on the paper by G.W. Heunisch (MINING ENGINEERING, January 1987), which raised several important points regarding treatment of acidic waste waters. This paper confirms, in part, tests carried out by Allyn Corp. Allyn is the manufacturer of the proprietary product Alka-Ment, one of the materials that Heunisch tested. The first point is the extreme sensitivity of the sedimentation rate on the nature of the treatment material used. This apparently results from differences in nucleation of the metal hydroxides, and is consistently higher for Alka-Ment. This decreased sludge volume is also observed when Alka-Ment is combined with flocculants, such as organic polymers (see Table 1). Our second point is to emphasize that Heunisch's work shows how dependent the sludge volume is on pH. It is common practice to overtreat AMD by raising pH to 9 or 10. This practice, in addition to being wasteful of material, actually decreases the density of the resulting sludge, probably by creating charged particles that do not readily coalesce. When treating with Alka-Ment, we recommend that the treatment be monitored by testing both pH and dissolved iron. For both tests, it is important to allow adequate time to elapse between treatment and measurement, so that dissolution of alkali, aerobic oxidation of iron, and precipitation of the metal hydroxides are nearly complete. Our tests have indicated that from 30 minutes to one hour is commonly required. Only in this way can a minimum pH be attained, with adequate treatment, denser sludge, and lower treatment rates achieved. Thirdly, Heunisch correctly recognizes that ASTM titration of Alka-Ment does not reflect the true treatment value available in a unit of Alka-Ment. Our work at Allyn indicates this is a most important consideration when evaluating various materials for the treatment of acidic waste waters. While we were unaware of Mr. Heunisch's work, we welcome comparisons between Alka-Ment and any competitive products readily available for field use. Allyn has hundreds of hours of laboratory and field data we are ready to share with interested parties treating acidic waste water.

Jan 9, 1987

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016