Search Documents

By M. Machina

Anew approach to the use of projectiles for rock fragmentation uses recently-developed technology to optimize projectile shape and composition to achieve the desired type of breakage. Projectiles can also be made of various materials, as determined by the requirements of downstream processes. This paper describes laboratory tests with an 21-mm (8-guage) gun, and field tests with a 60-mm cannon.

Jan 1, 2003

By Edwin Itzig-Heine, Daniel Traylor, Bernard Tarralle, Michael McKenna

This paper discusses the challenges associated with the design and construction of a dual-cell, “figure eight” shaped shaft in saturated, soft ground for the Northeast Interceptor Sewer project in Los Angeles. The shaft will be excavated to a depth of41 m and used to launch two EPB TBMs. The specifications required concrete diaphragm walls, embedded below the shaft invert, and a grout curtain beneath the wall. To control water pressure and basal stability without a grout curtain, wall panels were embedded deeper than required into a stiff, cohesive deposit. Details of wall panel excavation using a Hydrofraise are presented.

Jan 1, 2003

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By F. F. Peng, S. S. Peng, V. Z. Sun

A detailed study of ponding phenomenon relative to surface subsidence due to longwall mining was conducted for various surface stream conditions. Based on field monitoring, the stream-ponding process and three forms of stream water are described. Also discussed are the criteria of stream ponding and the influences on the ponding process by two key factors: the angle of stream flow and the change in the stream-bed gradient. A numerical (mathematical) model, which combines trend surface technique that describe the topographical features in the vicinity of a stream and the modified influence function, which represents the profile of the surface subsidence trough (or basin), is constructed to predict the formation characteristics of stream ponding in terms of location, boundary and accumulated water volume of migratory and stationary ponds produced by the stream-ponding process. Three cases are analyzed using the model to predict the interaction of the underground operations and the environmental impact due to stream ponding. The feasibility of various mitigative measures are assessed.

Jan 1, 1997

By Carl (Original by) Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb e earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled.

Jan 1, 1981

By Molood Saeedi, Nima Sadeghi, Eskandar Keshavarz Alamdari

This study showed the kinetics of gold chlorination leaching from an anode slime complex containing copper, silver, barium, selenium, and tellurium. AgCl and BaSO4 control the rate of gold leaching, and the interface transfer and diffusion across the product was selected as the desirable kinetic model. The concentration of hydrochloric acid, chlorine gas flow rate, pulp density, and temperature have been precisely studied. The results showed that temperature and hydrochloric acid have a favorable influence on the leaching rate. However, the chlorine gas flow rate is inactive in the reaction rate. Furthermore, the leaching rate decreased with an increasing pulp density. The leaching process was controlled by the interface transfer and diffusion across the product, and the activation energy was determined to be 13.66 kJ mol–1.

Oct 19, 2021

By Betty L. Gibbs

Before the first shovelful of dirt is removed from a developing mining property, a wide range of data must be collected, organized and analyzed. Among the key steps in this process are: • Visualization of the deposit from drill hole data and geologic interpretation, using all available information, including surface geology, geochemistry and geophysics. • Drawing of vertical and horizontal sections. • Construction of a 3D solid model of the deposit. • Contouring of deposit outlines and geological structure until the model represents best estimate of reality. • Estimation of grade and quality distribution. • Calculation of reserves. • Examination of possible mining methods. • Determination of economic feasibility. Many techniques are available to aid in this process of mine project feasibility analysis, from quick pencil calculations to sophisticated computer methods. However, time races faster in the complex modem business world than it did 50 years ago. Tried and true pencil methods take too much time. Opportunity may pass a mine developer by while a property is still in the first stages of analysis. In the days of hand techniques, initial analysis of the economic feasibility of a mining project usually stopped with reserve calculations and broad mine planning. Further planning was not done or was done only for the short term. Manual techniques require too much time and manpower to evaluate a longterm mining program. Mining-industry recognition of computer utility has increased. Most companies now use computers in technical applications and could not conceive of working without them. Building initial computer models of a deposit may take nearly as long as hand techniques. But the payback comes when changes are needed and a variety of mine plans are quickly tested.

Jan 1, 1990

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2009 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on industry exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2009: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2009 and were compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2009, primarily for base metals (copper, lead, nickel and zinc), diamond and precious metals (gold, platinum-group metals and silver). Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis prior to 2008. The MEG survey methodology was changed in 1999 to include companies with exploration budgets greater than $100,000, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2009 survey is reported by MEG to cover an estimated 95 percent. Companies who chose not to participate in the MEG study, private companies that do not publish data and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 86 more companies in its 2009 survey than it did in 2008.

May 1, 2010

By M. Springett

Organization of teams for rapid and effective evaluation of international mining properties requires special considerations beyond those needed for domestic activities. Experience, technical ability, a sense of perspective, humor and self-discipline are vital characteristics to look for in the selection of individuals for forming an efficient and productive team.

Jan 1, 1994

By A. Mertzanis

The way and methods used for the surface mining of bauxite until the end of the twentieth century in the area of Ghiona, resulted in a significant burden to the natural environment, especially in the cases where it covered extended parts of forests and forest areas as well as important geomorphological formations. The impacts from the surface mining of bauxite which in fact constitute the object of this study relate mainly to the interruption of the natural continuity of the land relief and the alteration of the natural geomorphological activities and are due to: a) the alternating excavations with fronts of great heights, b) the depositions of large volumes of waste materials which originate from the revealing of the ore and c) the dense road network constructed in order to get access to the mine locations.

Jan 1, 2006

By A. Haghighat

The Missouri University of Science and Technology?s (Missouri S&T) Experimental Mine is a teaching and research facility which has been excavated in limestone by mining engineering students over almost 100 years. The mine is currently being extended to a second level. Available fans for ventilation are two surface fans of 24 kW and two underground booster fans of 12 kW. The design of a ventilation network in conjunction with multi surface fans and booster fans entails a complex procedure. Ventsim Visual software modeling has been used for network analysis to determine the optimum surface and booster fans locations, blade settings, and speeds. Both natural and mechanical induced ventilation pressures have been taken into account. Three working faces on each level have been designated as target points that minimum air quantities are required. The model has been calibrated against a pressure and quantity survey. Design of ductwork, door/stopping positions and different fans characteristics have been examined. The optimum flow rate at identified working faces, efficiency and minimum energy losses and annual network power cost determine the best scenario. The optimum design has been determined for the ventilation network for the next 100 years. The optimum flow rate across working faces is the key criterion selected.

Feb 23, 2014

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020

By Richard R. Klimpel

The purpose of this paper is to summarize some of the author's experiences in applying population balance models to a variety of industrial grinding circuits. Over 26 separate industrial circuits have been studied in detail during the last 10 years, each unique in its equipment type and layout as well as in the material (s) being ground. The success of the population balance approach during these studies was variable. Fourteen of the circuits were shown to be very amenable to such an approach while the remainder had conditions present that sufficiently violated the standard population balance assumptions so that the analysis was of less than optimal utility. Some discussion of the importance of standard population balance assumptions will be given. It is increasingly becoming this author's opinion that the use of population balance models has its greatest utility in defining logically and cheaply (in contrast to actual physical testing), the relative limits and comparisons of different proposed circuit configurations and changes in equipment types and/or operating conditions. As far as specific quantitative predictions and actual optimization of existing plant performance, the results of applying the population balance approach have been often disappointing and need to be coupled at the plant level with other engineering quantification techniques in order to achieve desired improvements.

Jan 1, 1992

By Ma Fangyuan, Li Min, Xu Bing, Xian Yushuai, Zhao Tonglin

The study explored a new combination amine collector (XK-28) that can obtain better flotation index and defoaming rate for magnetic iron ore. A pure quartz mineral test indicates that dodecylamine, XK-I, or XK-II has good collection effect on quartz and their best flotation pH is in the range of 6–7. The experimental results of a combination collector (XK-I:XK-II = 2:8.) show that the separation effect for quartz and magnetite is better than that of a single collector. The single factor for actual mineral test shows that when the combined reagent is used as the collector, the best conditions are pH = 7, 90 g/t dosage, and XK-I:XK-II = 2:8, which is consistant with the pure mineral test. The difference for dodecylamine as a collector is that the optimal dodecylamine dosage is 60 g/t. Under the best conditions of actual ore test, dodecylamine and XK-28 are respectively used as the collector to compare the flotation indexes. Study results indicate the magnetite grade using XK-28 as the collector is higher by 3.02% than that of using dodecylamine, recovery is increased by 1.92% over that of using dodecylamine. Based on the measurement results of zeta potential, uses of XK-28 can slightly increase the zeta potential difference of quartz and magnetite to enhance the flotation effect. The mechanism of action between the XK-28 collector and the actual ore from the Gongchangling plant is physical adsorption, and this adsorption also has hydrogen bond formation. Contact angle results shows that XK-28 improves the hydrophobicity of quartz better than dodecylamine. Compared with dodecylamine, XK-28 is more sparsely arranged on the surface of the foam. The foam produced by the XK-28 collector has better air permeability and it is more likely to merge and disappear with bubbles.

Jul 21, 2021

By W. H. Andrews

DEFINITION OF BAUXITE The term "bauxite" (1) dates back to 1821, when it was assigned to a deposit of red earthy material outcropping near the village of Les Baux in Southern France. Chemical analysis indicated the presence of aluminium oxide, iron oxide and water. Deposits of bauxite are widespread throughout the world although the major developments occur within 30 degrees of the Equator. Essentially bauxite is the product of weathering and leaching of a variety of sediments or rocks, generally in a high-rainfall tropical or sub-tropical climate, resulting in the enrichment of the aluminium oxide content. It is characterised by the presence of one or more of the minerals, gibbsite, boehmite, and diaspore. The other constituents are usually clay, (typically kaolin), hematite and/or goethite (iron-oxides), anatase (titanium oxide), and possibly silica as quartz. A variety of minor elements may be present, such as calcium, magnesium, phosphorus, vanadium, gallium, manganese, and many others in very small quantities. Organic compounds are normally present from development in association with a soil horizon where vegetation may be encouraged by the high rainfall necessary for bauxitisition. The physical form depends upon the geological history of the deposit and correlation also exists with the mineralogy. Older deposits which have been subject to burial are invariably hard and compact with the alumina predominantly occurring as boehmite or diaspore, while the more recent, surface deposits are frequently less compacted and gibbsite is the dominant alumina mineral. In these later deposits, the physical form can vary from the fine red soil (terra rosa) of Jamaica to the Weipa pisolites to the cemented Arkansas type. The presence of concretionary structures is an important aid in identification in the field.

Jan 1, 1984

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are in most cases developed and tested in close cooperation with demanding end users before Being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the Drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, Atlas Copco has placed emphasis on hole straightness and the need for hole logging and positioning. By applying state of the art Technology to today?s computerized drilling rigs, major steps in improving overall drilling and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the Rotary drilling product line.

Jan 1, 2010

By Joe Keane

DOUG HALBE: The kickoff speaker, and my unanimous choice, is Joe Keane. Joe was born in Butte, Montana, and began his association with the mining industry as an under- ground miner at age 16. Currently he is president of KD Engineering and Metcon Research. He had it lucky when he went to school because there were only 44 elements in the periodic table, I understand. [laughter] Here's Joe. JOE KEANE: I'm doing this under protest. Maybe we can start the slides. Mr. Halbe gave me this topic, but I don't like it. I don't like Mr. Halbe either [laughter] because of the way he shanghaied me into this. He called me up on the phone and said this is what you're going to speak about: "Five Things I Never Want to See Again in Plant Design," and I said, "Huh!" Then I started getting stuff from SME about how to make a presentation. I have decided to change the title to "More Than Five Things I Never Want to See in Plant Design," since you can't have a completely negative speech; you have to have other topics. So we will have some other, not completely nonrelated, topics to sort of break the tension. I tried to find a joke to open with. I talked to Omar Mutati. All of his jokes were either about Bill Clinton, our beloved President, or they were too filthy to say in a mixed group. [laughter] So I decided to start this out with a profound statement. The pro- found statement is, "The meek shall inherit the earth, but not the mineral rights," [laughter] by J. Paul Getty. J. Paul Getty was one of my favorite guys because when a real obnoxious reporter asked him one day, "How can I become wealthy?" he said, "Drill for oil and find it."

Jan 1, 1998

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023

By John Keefner, Charles Kocsis, Kyle A. Scalise

Geotechnical modeling of mines is crucial for understanding the many factors that can pose potential hazards or limit production opportunities. The process of back analyses for modeling is often used, but in many instances, the back analyses can be cumbersome and time inefficient.While thesemodels and back analyses may be accurate, these types of back analyses may not be ideal to be used at mines and by engineers because the process is so time-consuming. This paper introduces event-based back analyses that utilize prior events to create more accurate models while eliminating large modeling time because the models are back analyzed from previous events. The completed analyses supply a more detailed insight into the potential hazards at Round Mountain, an open pit operation, as well as provide a better understanding of how improper risk analysis results in missed opportunities. The more we understand about mining activities and processes through modeling, the safer and more productive mines will be.

May 24, 2021

By Wei Victor Liu, Omer Faruk Ugurlu, Chengkai Fan, Bei Jiang

The accurate prediction of truck productivity plays a pivotal role in improving the efficiency and profitability of open-pit mining operations. However, predicting truck productivity is challenging owing to the complex nature of the working conditions of the mine site. This paper proposes a deep neural network model to overcome the challenge of predicting truck productivity in open-pit mines. The prediction model was built using eight variables and was optimized by considering different train-test split ratios, numbers of hidden layers and neurons, and activation functions. The proposed model's performance was evaluated using various metrics and was compared with other commonly used machine learning algorithms. According to the results, the proposed model outperformed traditional machine learning algorithms by achieving higher accuracy and lower error rates, with the best-performing model having four hidden layers with 70 neurons per layer and a scaled exponential linear unit activation function, resulting in a coefficient of determination value of 0.89. This demonstrates the potential of deep neural network models for predicting truck productivity in open-pit mine sites. Moreover, a single variable sensitivity analysis was conducted to investigate the impact of input variables on truck productivity. The results show that haul distance is the most influential variable for the prediction of truck productivity.

Feb 12, 2024