Search Documents

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017

By Kyle Kittle, Kyle Knaeble, Albert Ruiz, Gregory Raines, Ryan Gewargis

The Chimney Hollow Reservoir Project (CHRP) is located southwest of Loveland, Colorado. CHRP is a component of the Windy Gap Firming Project, operated by the Municipal Subdistrict of the Northern Colorado Water Conservancy District. The inlet/outlet tunnel (IOT) for CHRP contains a reinforced concrete lined alve Chamber with PC membrane waterproong that was ecavated via seuential ecavation method to a diameter of feet. The IOT was ecavated using both drill and blast and road header with ground support consisting of steel sets, rock bolts, wire mesh and shotcrete. The IOT will withstand 300 feet of water head and rock ll surcharge load from the dam embankment constructed over the tunnel.

Jun 23, 2024

By Paul T. Allsman, Paul F. Yopes

17.1--CURRENT AND FUTURE STATUS OF SURFACE MINING PAUL T. ALLSMAN AND PAUL F. YOPES 17.1.1--CURRENT The history of surface mining essentially is one of mining coal, copper, iron and aluminum ores, of placer mining gold and tin, and of pits and quarries producing clays, gypsum, phosphate rock, sand, gravel and stone. Table 17-1 is a summary of the estimated world and United States production of crude metallic and non¬metallic ores and coal in 1969. It includes estimates of the quantities produced by surface-mining methods. Two-thirds of the 10 billion tons are mined from the surface, ranging from a third of the coal. 57% of the metallic ores, and nearly all clays, stone, sand and gravel. Production by surface methods in the United States, parallels that of the world with one exception: about 90% of the copper and iron ore is mined from the surface, whereas elsewhere only about half the copper ore is surface mined. In Canada, surface mining of the Athabasca tar-sand deposits is a recent large-scale unique operation. In surface mining of coal and, to a lesser extent, metallic ores, much waste is stripped, but in nonmetallic pits and quarries the ratio between waste and ore usually is small. Assuming that the stripping ratio for surface mining in the

Jan 1, 1973

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

By DIONISSIOS T. HRISTOPULOS, JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Zach Agioutantis

Explosions in underground mining due to methane gas have been the leading cause of incidents and fatalities in the mining industry. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the United States. The AMS data were preprocessed and statistically evaluated to explore the potential autocorrelation of methane gas. It was concluded that the autoregressive integrated moving average (ARIMA) time series model used in the one-step-ahead forecasting mode provides accurate estimates that match the increase or decrease of the methane gas emission data.

Feb 1, 2023

By W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of freshwater whose origin can be traced to the present and historical courses of the River Indus. In the past the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water-table has risen to within a few feet of the surface. The river system itself is being progressively developed for irrigation and very shortly a situation will arise where the entire low winter flow will be utilised. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilise the water-table at safe depths. This paper discusses some of the methods used to ensure optimum-economic development of the fresh groundwater and describes the general design philosophy evolved by the authors firms for both irrigation and drainage wells, with respect to both well configuation and operation. Water quality standards are discussed in as much as they affect subsequent use of the groundwater. A few particular aspects are considered, including that of the values of the relevant aquifer constants, the construction of wells and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to-produce fresh water from layers overlying saline water. This solution is also discussed.

Jan 1, 1967

By Diogo Peixoto Cordova, Italo Gomes Gonçalves, Andre Cezar Zingano

The top-down extraction sequence in the sublevel open stope method relies on rib pillars to support excavations, making pillar and stope stability crucial for controlling dilution. This study introduces an integrated methodology using a genetic algorithm to optimize the layout of open stopes and rib pillars while considering both economic and geomechanical performance. The methodology incorporates user-defined parameters such as the minimum size of stopes and pillars, maximum accepted dilution and acceptable percentage of pillar failure. A profit function that attributes economic value to the geometric configurations, including geomechanical performance, is employed. The geomechanical performance, assessed using numerical models in FLAC3D, includes the average percentage of pillar failure and potential dilution. The study was tested on a mining panel from an underground gold mine using a top-down mining sequence. The optimization achieved an 8 percent increase in net profit compared to the traditional engineer’s design when 70 percent hangingwall support efficiency was assumed, and a threefold reduction in pillar failure percentage. When no hangingwall support was considered, the net profit increase reached 22 percent. These results demonstrate that the proposed methodology enables integrated optimization, balancing mining costs with geomechanical performance and reducing the need for secondary support compared to traditional methods

Nov 1, 2024

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By R. L. Eppley

The Blacklick Creek Watershed Association was awarded a $158,000 Growing Greener grant from the Pennsylvania Department of Environmental Protection in 2002 for the design and construction of a sulfate reducing bioreactor (SRBR) cell to treat acidic discharge from the Judy 14 abandoned underground coal mine near Indiana, PA. The vertical flow SRBR was designed to treat 38 liters per minute of MIW containing elevated concentrations of aluminum and iron. Other treatment systems at this site plugged due to aluminum precipitates; this problem did not occur in the SRBR. The bioreactor has been periodically overloaded with flows up to six times the design rate. To date, the only maintenance performed on the unit has been the addition of hay to the surface of the unit in response to less than expected performance. The periodic hay additions appear to have restored the SRBR to nearly post-construction levels. Since construction, the SRBR has treated about 136,000 cubic meters (36 million US gallons) of MIW.

Jan 1, 2010

By P. Brooks, W. LaRochelle, J. M. Tranquilla

EMR's recently commissioned Pilot Plant in Fredericton, N.B. Canada, the latest and largest in the company's sequence of prototype and demonstration systems, is being used as a process development facility for mining clients worldwide. Fitted with two microwave reactors and 75 kW generators, this plant is designed as a two-stage continuous processor with a throughput in the 5-10 tpd range depending upon the material feedstream. This facility has been used principally to calcine pyrite and arsenopyrite gold concentrates although it can readily accommo­date carbonaceous materials as well as a wide range of other ore types. Engineering details of the plant and the results of the first nine months of operation are presented. The plant has proven very successful as an advanced process development facility as well as a basic production unit module.

Jan 1, 1998

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By A. Kalogeropoulos, T. Michalakopoulos

The DEM has been used in several studies to numerically simulate the response of rocks to the cutting action with drag tools. In this research, the aim is to realistically simulate the rock material and the cutting process by controlling the grain interlocking of the numerical assembly and streamlining the calibration process while focusing on the cutting force and the failure mechanism.

Apr 1, 2023

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015

By Donald R. Simon

Money... not many subjects are as personal or as emotional. Hessiod said it well in 700 B.C. "Money is life to us wretched mortals". Are you getting paid enough? Does your company reward its top people? Does coal or copper pay more? Production or engineering? How is the synfuels industry going to influence mining salaries? Do high salaries attract and retain the best people? Do modern compensation systems ensure fairness or destroy entrepreneurial spirit? With our tax system and high standard of living why are we so salary conscious? Salary is not only important for what it can purchase but it is also a yardstick, measuring how well we are doing. We all need money to pay the bills and maintain our standard-of-living, but once we reach a certain point the psychological ramifications become more important than the purely practical side. Even necessary payments like the mortgage and the car are a function of our egos. Are our choices of cars and homes based on simple transportation and shelter?

Jan 1, 1980

By Richard E. Ray

Conventional concrete block plastered with a cemantitious coating is the most common material used in the construction of perma¬nent stoppings to direct airflow in underground mines in the U.S.A. All mines experience various degrees of strata convergence depending upon depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting in significant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating "Max-Seal" polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased several-fold in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1984

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

With the depletion of mineral resources and the growing demand for metal resources from industrial development, the recovery of metal resources from secondary resources has attracted increased attention. Among all secondary resources, spent catalyst is one of the most important as it contains valuable metals such as vanadium, nickel, molybdenum, cobalt, and aluminum. Compared with the extraction of metals from minerals, the recovery of valuable metals from spent catalysts has the advantages of a simple process, a short production cycle, lower investment cost, and less environmental impact.

Apr 1, 2023

By J-P Strydom, J P. Z, S. Schafrik, M. Beck, Z. Agioutantis

Developing a method to accurately determine the weight and distribution of the load within a shuttle car bed eliminates the need for manual activation of the flight chain. Accordingly, this experimental study characterized the thermo-mechanical response of two unique load cells in force shunt, implemented as an engineering control to quantify load position and distribution without human intervention. The influence of environmental and installation conditions on the measurement accuracy was quantified and determined to be indirectly dependent on the characteristics of the material load cells that are mounted to.

Feb 22, 2026

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By Paul Kents

The Canadian Javelin Limited Cerro Colorado copper-porphyry deposit in Panama, possibly the largest known copper-porphyry, contains between 1350 and 450 meter elevations, drill proven and probable ore in excess of 3.0 billion tons averaging 0.65% of copper equivalent. The deposit is located in the Central Cordillera Range, straddling the Continental Divide at 1500 meter elevation. Local topography is very steep. Accessibility is difficult, all logistics made by helicopter, and only recently a 52 km. road from the Pan-American highway was completed into the area. The deposit was discovered in 1969, and since then 75 shallow exploratory holes and 98 deep holes, the deepest 1340 meters, totalling 45,000 meters have been drilled. Deep holes were drilled at the corners of a regular rectangular 150 meter grid.

Jan 1, 1975

By W. C. Dailey

The Groveland Mine. Concentrator and Pellet Plant are located in Dickinson County in the Upper Peninsula of Michigan. The construction of the Groveland Mine in 1959 was the first United States operation for the Hanna Mining Company in mining and beneficiating low grade iron formations. (1) The plant produced concentrates at 675,000 lt/yr. (746,600 mt/yr.) which was used as sinter feed in the steel industry from 1959 to 1963. Upon completion of a pelletizing plant in April, 1963 production increased to 1.6 million lt/yr (1.77 million mt/yr) of pellets. After the plant expansion, mill capacity increased to 2.2 million 1t/yr (2.43 million mt/yr.), producing 2.0 million It/yr (2.23. million mt/yr.) of pellets assaying 63.0% iron and 7.0% silica. (1) Prior to April, 1971 the concentrator operated with a flowsheet consisting of spirals and a petroleum sultonate iron notation circuit. This was presented in a paper by R. R. Smith and E. E. Sougstad, "Flotation at the Groveland Mine" in the 50th Anniversary Volume entitled "Froth Flotation". The ore body at the Groveland Mine consists basically of two types of iron formation (34% total iron, 20% magnetic iron head), the most abundant of which is a bedded magnetite-chert-silicate rock. This is intermingled to varying degrees with non-bedded to poorly bedded hematite-clastic quartz-chert rock. (1) In developing the Groveland flowsheet, Humphrey spirals were used because of their ability to produce a coarse size concentrate at a low cost. Tests run in the lab and pilot plant on the Groveland ore showed a. spiral weight recovery in the 27 to 33% range. (2) However as the ore body was opened up, it became evident that the most abundant ore type did not liberate at the coarse size fraction needed for spirals. Plant recoveries for the first five years operating the spirals only averaged from 10 to 15% weight recovery. In 1971 the weight recovery on the spirals had dropped to a low of 5%. To increase iron recovery and at the same time increase plant capacity with the least effect on the present operations the mill flaw-sheet proceeded from a spiral-notation circuit to an all flotation circuit to a magnetic separator-flotation circuit. During this changeover the concentrate grade also had to be improved to meet market demands. To do this the following changes evolved

Jan 1, 1978