Search Documents

By Thornton L. Neathery

A small area in the Alabama Piedmont was studied to determine if metallic enrichment was associated with local magnetic anomalies. Cores from two holes in these magnetic anomalous areas have sulfide (pyrite, pyrrhotite, chalcopyrite) film on slicken-side and fracture surfaces. Two hundred and fifty soil samples were collected from the top of the "B" horizon on 1, 000 foot centers over the general trend of magnetic anomalies. Soil samples were leached with a 1:2. 7 mixture of HF and H2SO4 and the dilute filtrate analyzed for Cu, Pb, Zn, Ni, Co, Cr, Mo, and Cd, using atomic absorption methods. Concentration-value maps were prepared for each element. Small areas of anomalous concentrations were defined for Cu, Pb, Zn, Mo, and Ni. Some of these areas generally coincides with magnetic anomalies. Concentration values (ppm) range from: Cu 165.0 - 0. 5; Pb 265. 0 - 0.0; Zn 1386.0 - 43. 0; Ni 187.0 - 10.0; Co 207.0 - 6. 5; Cr 117.5 - 2.0; Mo 95.0 - 0.0; and Cd 32. 5 - 2.0. Studies of other magnetic anomalies appear warranted.

Jan 1, 1972

By Paul M. Godlewski, Roberto J. Guardia

Hundreds of highway and rail transportation tunnels in North America have been rehabilitated in the last two decades. Tunnel rehabilitation is usually dictated by an owner’s need to extend the working life of the structure, but typically has the added benefit of increasing capacity (greater speed or increased clearance) and enhancing safety. Not only has rehabilitation proven to be an economical alternative to new tunneling, but it can be safely accomplished by working during short work “windows” without taking the tunnel out of service. This paper presents methodology for planning and designing of tunnel rehabilitation projects, and case histories illustrate successful excavation and support technologies.

Jan 1, 2003

By S. Bassignani, D. Ippolito

In Italy at the moment there is a program which involves for the future the exploitation of two uranium mines which are now in the research stage. About one hundred and fifty workers are at present employed in those facilities. An health physics surveillance program is under way and has been designed to fulfill the requirements due to the future exploitation of the two mines. A complete evaluation of the total dose (external + internal) received by the workers will be given together with a detailed analyses of the technical methods employed for such evaluations. The external doses are evaluated on the basis of individual TLD dosimeters, while the evaluation of the internal doses is mainly due to an enviromental survillance program of the radon and radon daughter air concentration inside the mines. The criteria established for the assessment of the sampling procedures, sampling intervals and dose evaluation related to the radon doughter exposure are reported. The external dose received by the workers are lower than 0.2 m Sv~month and the internal exposure less than 6.4 IO-3 J.h.m-3 /year or using the old units 2 WLM/year.

Jan 1, 1981

By John Carson

Belt feeders are commonly used to meter the flow of bulk solids from bins and hoppers. If the interface between the hopper outlet and belt feeder is not designed correctly, flow from the bin may be severely compromised, resulting in problems of no-flow, segregation, flooding, etc. By knowing the flow characteristics of the bulk solid being handled and applying proven design techniques, such problems can be avoided. Relevant bulk solids flow characteristics are identified, along with measurement techniques. Design procedures for correcting problems with existing feeders as well as proper design of new feeders are presented, along with case histories of successful application of these procedures.

Jan 1, 2008

MULSIM/NL and La Model are displacement-discontinuity programs which have been used quite successfully in the past to provide detailed structural models of various single and multiple-seam mining situations. However, both of these programs required fairly complex details of the mine plan and topography to be manually input into the program, often taking several days of work. Recently, automatic mine and topographic grid generation capabilities have been added to the MULSIM/NL and La Model programs, reducing the input time requirements from days to hours. This paper discusses the algorithms used for the automatic grid generation and demonstrates the utility of the new capabilities with a case study.

Jan 1, 2003

By S. P. Singh

In order to understand the intricate nature of blast damage mechanism and to counter the associated problems, small scale blasting experiments were performed on hydrostone, concrete and granite. This was followed by a 2.4 m x 2.7 m (8'x 9') drifting operation in a quartzite quarry. Interior as well as exterior damage was assessed by different techniques. On the basis of the experimental results, the effect of explosive characteristics on the damage was examined.

Jan 1, 1992

By J. Pang, S. Chander, A. Briceno

The mechanism of sulfur oxidation in pyrite is a function of the rate and driving force for oxidation. New evidence is presented to show that, at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Pyrite is hydrophilic under these conditions. In the presence of iron-chelating agents or iron sequestering ions, an iron layer might not form. Under these conditions, the sulfur layer is exposed, and the pyrite might become hydrophobic. Stronger oxidizing conditions decompose the sulfur layer, thereby making the surface hydrophilic.

Jan 1, 1994

By Tuncel M. Yegulalp

In this paper we revisit the well known "Ultimate Pit Limit Problem" and suggest an alternative approach for fast and efficient solution. We follow the approach originally proposed by Johnson and Barnes (1988), but utilize the "Excess Scaling Algorithm" in solving the equivalent maximum flow problem. This algorithm provides significant increases in speed and reduction in memory requirements over the well known Labeling Algorithm of Ford and Fulkerson (1956), enabling one to solve large problems with relatively small computers. We present results of a series: of benchmark tests using this approach against the well known Lerchs Grossman algorithm as well as a brief description of the new algorithm.

Jan 1, 1992

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum exposit, Eureka County, Nevada, occurs in a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusives. For samples from the 25 000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8:1 at 10-mesh, 8:1 at 70-mesh, 6:1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp is used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of + 25%. The error distribution is not biased. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1992

By R. V. Ramani

This paper is based on the thesis that the demand for computer-oriented mining engineers will continue to sharply increase in coming years. It presents the philosophy behind the development of a mine systems engineering program at The Pennsylvania State University. The paper discusses the current status of mining engineering education and the problems encountered in integrating extensive computer background and education into a traditional mining engineering program. The paper analyzes the interrelated roles of research, graduate studies, and continuing education in developing a comprehensive program of study. It is hoped that this program philosophy will be useful to other institutions which are contemplating new programs and courses in emerging technologies.

Jan 1, 1982

By R. P. King, M. K. McCarter, K. S. Free

Mine plans typically consider the profits and costs associated with extracting and processing minerals into marketable products. Interrelationships between mine and mill costs are often overlooked during the process of mine plan optimization. A simple and quick method for predicting milling costs for a given block would improve the planning process, especially if the procedure could be incorporated as part of routine ore grade analysis of drill core or cuttings. Incorporating milling costs as part of the mine planning process could improve overall optimization of the mine/mill combination. A method developed by the Utah Comminution Center (UCC) at the University of Utah provides a possible answer to the need for quick and reliable grinding cost estimation (King et al., 1996). Using results from single-particle impact tests, a work index, called the Utah Load Cell Work Index (ULCWI), is calculated. The potential for routine use of the new method is explored by comparing ULCWI values with corresponding Bond Work Index (BWI) values for eight mineral materials (Free, 2000).

Jan 1, 2004

By T. A. Toney, L. R. Fish, P. J. Bethell

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers and recirculation have been attempted with some success. This paper reports on a novel (patent applied for) approach to retreating spiral middlings in a heavymedia cyclone circuit.

Jan 1, 2000

By F. H. Mertens

The concentrators of Gecamines are fed by a great variety of ores and produce different types of oxide and sulfide concentrates. It is therefore important to translate the performances of each circuit in terns of dollars in order to reach cost optimization in each mine to product line. A new system has been recently implemented for achieving this objective. Technical data and expenses are collected, allocated and analysed on mainframe applications. On the other hand, optimization and simulations are carried out on microcomputers which are linked with the mainframe files. Various kinds of auditing reports can be produced, including those leading to investments and cash-flow pattern which are

Jan 1, 1991

By Robert J. Wise, Mark Alspaugh

Underground longwall coal mines depend on conveyor haulage to transport large volumes of coal from the longwall face conveyor to the mine portal. In the last few years, the need for longer and larger longwall panel conveyors has become very significant. In order to keep conveyor equipment to a minimum and still transport higher tonnages over longer lengths, intermediate drive technology has been developed. The use of DC motors and controls in conjunction with load sharing techniques have a1 so proven effective. A case study of a new longwall panel conveyor at Utah Fuel's Skyline Mine incorporating these design techniques will be presented.

Jan 1, 1993

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By Fred J. Fleischauer

Industry requires higher speed sheet stacking. High speed sheet stacking requires equipment and techniques to solve several inherent difficult problems, such as the tendency for sheets to sail, and the need for a means to absorb the kinetic energy of the sheet without damaging the sheet. Accurate alignment of the sheets on the stack is another problem difficult to solve. The paper first analyzes the process of sheet handling into its basic elemental steps. It then describes equipment and techniques presently used for moderate sheet handling speeds, with emphasis on how each step in the stacking process is accomplished by the present equipment. The limitations to speed-up of present equipment is discussed. New high speed equipment, either recently introduced to the market, or in the process of development, is described. Magnetic, air float and vacuum conveyor stackers are compared.

Jan 1, 1973

By Peter I. Brooker

The turning bands method for the simulation of spatially correlated data in two or three dimensions requires that the relation- ship between the covariance obeyed by the realizations first generated on lines, and the covariance of the two or three dimensional process must be solved. In three dimensions the solution is immediate, but in two dimensions the integral equation relating the covariances of the one and two dimensional processes is more complex. This is solved in this paper and is applied to the most common model used in ore deposit description, the spherical covariance.

Jan 1, 1984

By A. M. Gaudin

In the first place, let me thank you for inviting me to appear before you today to speak to you on "Mineral Industry Problems - Present and Future". It is a distinguished honor for me to have this opportunity, and I am highly appreciative of this distinction. The beautiful surroundings of Gatlinburg and the pleasantness of a summer occasion are a wonderful tonic for all of us, yet they should not blind us to the seriousness of our Industry&apos;s problems No doubt, because of my past appearances before members of the Society of Mining Engineers, at which I discussed wholly scientific topics, or research in the Applied Sciences, you may be expecting me to revert to these subjects. But I intend to venture in a field that is new to me, yet old to all of us, the field of Economics.

Jan 1, 1962

By A. L. Hannaford

Previous production at Spektakel was undertaken during the periods 1854 - 1888 and 1892 - 1901. During this period a total of 41,7 kt of ore grading 32% Cu was hand-sorted from 270 kt to 360 kt of ore mined. Initial open-pit mining was followed by underground mining, access being by means of an inclined shaft to the 85 fathom level. During the period 1946 - 1952 cement copper equivalent to 5,452 kt of blister was produced by leaching of oxidized ore. The Spektakel ore-body branches and coalesces both in plan and in cross-section which accounts for its remarkably complex configuration. Constituent rock-types are andesenite and various varieties of biotite diorite and of ?norite? (biotite-hypersthene diorite). Closely related spatially, and possibly genetically, but predating the above-mentioned basic rocks are bodies of biotite-bearing monzoritic rocks, locally termed shonkinita.

Jan 1, 1981