Search Documents

By P. R. McOllough

The Colorado Department of Highways awarded a contract to construct the Second Bore of the Eisenhower Tunnel in August, 1975. The contract was completed June 29, 1979, nine days ahead of schedule, with¬out major claims or delays. The tunneling involved complex construction through difficult ground conditions. The contract, plans and specifications were specifically planned to more equitably share the risks involved and to minimize adversary relationships. The Department produced a detailed tunnel design and maintained responsibility for the design. The contract employed some new provisions; e.g., a review board for settlement of claims and disputes; escrow documents (contractor's bid documents) to determine the contractor's basis of bid when determining adjustments. The tunnel contract, plans and administrative efforts employed by the owner and contractor were very successful in this project.

Jan 1, 1981

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By M. Saunders Macdonald

A number of open pit gold mines in Nevada extract ore from areas below natural groundwater elevations, necessitating dewatering and some method of disposal of the extracted water. These open pits extend well below the water table, with associated dewatering volumes greater than 10,000 gpm. Some mines, with large volumes of dewatering water to manage, have constructed re-infiltration basins to re-introduce dewatering water to the groundwater system some distance from the pits. This paper presents an overview of the state of the art of re-infiltration projects, including the permit process for such projects in Nevada, and the necessary engineering considerations.

Jan 1, 1996

By Brij M. Moudgil, Shoulian Zhu, J. L. Pinault

A new technique, prompt neutron activation probe (PNAP), for analyzing phosphate rock slurry in-situ was evaluated both in the laboratory and at the plant. The technique yielded a high precision in the analysis of Ca, Si and H using 252Cf source. Low accuracy of the direct measurement of P using 241Am/Be in the laboratory tests was attributed to the interference of rare earth elements present in the samples, particularly Gadolinium. No significant effect of variables such as solids loading, particle size distribution, and flotation reagents was observed on the probe performance. The probe can detect the compositional changes of the feed, tailings and the concentrate streams in the plant.

Jan 1, 1993

By J. Gawler

In June 2005 the Minerals Council of Australia signed a Memorandum of Understanding (MoU) with the Australian Government which states an intention ?for mining companies and government to work together with Indigenous people to build sustainable, prosperous communities in which individuals can create and take up social, employment and business opportunities in mining regions?. Implementation of the MoU has begun with demonstration sites established across Australia. All sites are using a Regional Partnership Agreement (RPA) model as a framework for enabling local people to find local solutions to local issues in partnership with mining companies, governments and Indigenous communities. Mining and resources companies can provide important input into regional economic development and capacity building by working through local partnerships. Company benefits include gaining a social licence to operate, access to a reliable skilled workforce, better longterm relationships with Indigenous communities and sustainable regional communities. All levels of government, Australian, State and Local, are working collaboratively to address unemployment and other issues in remote Indigenous communities. The Australian Government has adopted RPAs as one mechanism for implementing its whole-of-government approach to Indigenous affairs. This leading edge work is unique to Australia and the model has applications and significant learning for other countries and industries.

Jan 1, 2007

By Stephen Leslie

A multimedia tutorial illustrating the geology and mineral resources of Gulf Coast salt domes has been developed as a pilot project for a course on Texas geology and resources at the University of Texas at Austin. The principal objective of the tutorial is to educate students with limited background in geological sciences about a major local geologic feature and its geologic and economic significance. The content of the tutorial represents materials generally covered in 4 hours of lecture and laboratory instruction. These materials are presented using a flattened hierarchy of topics, each accessible from a central menu, including salt-dome history, salt tectonics, anhydrite and calcite cap rocks, mineral resources, and geophysical character. Information concerning salt-dome geology is communicated using interactive software; sound and animation are used throughout to reinforce key concepts. Visual aspects include field views, hand specimens, and photomicrographs that were digitized from slides. Illustrations were created using a graphics program or scanned from available archives. Each visual element has an accompanying explanation, which in many cases is linked to other parts of the tutorial. Navigation is accomplished using hyper-links or a set of unobtrusive buttons. The program includes a glossary of the major minerals associated with salt domes available as a pull-down menu and digitized video footage of the Gulf of Mexico sea floor to illustrate the active environment of the formation of the salt-dome cap rock. In addition, a group of interactive questions is presented to assess the level of mastery. Technical aspects were accomplished using a Power Macintosh ? 7100AV and a variety of commercial software. Actual linking of information was done with Authorware? 3.0 Educational, an icon-based, multimedia authoring program. Graphic illustration was done with Adobe Illustrator ?; image processing was accomplished using Adobe Photoshop?; video was cap¬tured, edited, and compressed using Adobe Premiere ?. The interactive nature of the project was designed with regard to future means of dissemination, especially on the World Wide Web. This tutorial serves as a template to build additional modules covering the entire course. A modular approach to the coding of the project and extensive self-documentation should ensure the viabil¬ity of the project by allowing other workers with moder¬ate computer skills to complete other lessons within the curriculum framework.

Jan 1, 1999

By Peter P. Harvey

The Nonel Primadet is a non-electric blasting initiation device. The system incorporates the safety advantages of a cap and fuse system with the precision blasting afforded by electrical blasting caps. Each unit is made up of a delay blasting cap factory-crimped to a Nonel® shock tube lead line. The delay elements in the blasting caps are manufactured in both millisecond and long period series. There are 16 periods available in both series - period 0 through period 15. The units are manufactured in 12', 16', and 20' lead lengths. The hollow shock tube is made of surlyn plastic and it is coated on the inside with a reactive material. The powder train has a density of only 1/10 grain per linear foot of tube. A typical blast round is timed precisely the same way it would be with electrical caps. After the round has been timed and loaded, the tube leads are gathered in convenient bunches and tied into a detonating cord trunkline. The Nonel® tube bunches are initiated by the output of an 18 grain per foot detonating cord trunkline. Once initiated, the Nonel® shock tube will reliably propagate at 1800 meters per second. The energy from this shock front initiates the delay elements in each delay cap. The shock tube is inert to electrical energies, including; stray current from AC/DC power sources, as well as, electrostatic discharges. The tube is also inert to initiation by impact. The system has proven to be particularly advantageous in both tunnel and shaft blasting applications. The major advantages in using the Nonel® system in this type of work are: 1) faster and easier tie-in techniques through the use of bunch-blasting. 2) electrical power can be left on during loading and tying-in. a. electrical lights can be turned on at the working face - better lighting facilitates loading and tying-in. b. electrical pumps can continue to function throughout loading and priming procedures (this is particularly advantageous in shaft work with water problems). 3) down-time due to approaching electrical storms is minimized. 4) increased overall efficiency in the blasting cycle: a. it is easier to train a man in the proper use of the system. b. fewer missed holes per round. c. less time required for tie-in. 5) safety-advantage--The system is not susceptible to involuntary initiation from extraneous electrical energies.

Jan 1, 1979

By F. L. Pierson

Since the discovery of 'potash in the Carlsbad area in 1926 and the start of mining operations in 1931, "first mining," operations have been carried on. This is a room and pillar system in which approximately 62% of the total ore is removed. Or the basis of ore reserves and rates of extraction, the life of the mine in the early; days was estimated to be well over 50 years, however, even with an increase by additional ore reserves, it became increasingly apparent that the life of the mine was being shortened considerably by increased production. Further cause for the shortening of mine life was due to the exceptionally weak back over the northeast quadrant of the main orebody which had .caved in on first mining up to a height of 8 feet. Thus, in 1953 the decision was' made to begin pillar pulling, also called, second mining or final mining, and in December of 1953 this program was started after much discussion.

Jan 1, 1965

By P. T. Perdue, F. F. Haywood

INTRODUCTION Monitoring devices used for detecting and measuring airborne radon in mines are limited due to the rugged environment in which they must operate. Personnel monitors now available are either passive or require filters and an air pump. Area air monitors usually have bulky batteries or require electric power service to the instrument. Thus, there are few instruments presently in use in mines capable of discriminating between the various radon isotopes and their daughters. Occasionally it is desirable to determine which radon daughters are the principal dose contributors in mine air. In some areas, such as the Elliot Lake mine in Canada, there exist sizable quantities of 220Rn in the mine air due to 232Th in the ore (Cote and Townsend, 1981). Since there has been recent interest in radon daughters in homes and factories, as well as caves and mines, methods and instrumentation are being developed to address these cases. Some of these methods can be employed in uranium mines. Although there have been very few determinations of the three radon isotopes (222Rn, 220Rn, and 219Rn) and their daughters made in uranium mines, these isotopes have been measured in process buildings and in private homes under circumstances that suggest these isotopes could also be present in uranium mine air (Perdue, Leggett, and Haywood, 1980; Yarborough, 1980) METHODS Cryogenic air sampling was developed about 15 years ago (Rasmussen, 1972) to concentrate various airborne chemicals for later fractional distillation and measurement of various organics using gas chromatography. A version of this technique has been developed to measure tritium, krypton, and other radioactive gases in nuclear power station buildings (Anon, 1980). In this method, fractional distillation is used in conjunction with various detectors to identify the radionuclides present. The cryogenic method to be discussed here was developed at Oak Ridge National Laboratory (ORNL). It uses the liquid air accumulated in a sampling device for a direct analysis of all gamma-ray emitters present. The air sampler (Fig. 1) could be employed in a mine to liquefy air, using the difference between the point of liquefaction of air (~80 deg. Kelvin) and the boiling point of liquid nitrogen (77 deg. Kelvin) to liquefy an air sample. By using a proper orifice at the entry to the sampling vessel, air of any dust concentration and relative humidity [ ] may be sampled. The energy for sampling is provided by the slow evaporation of the liquid nitrogen; no other power source is required. This type of sampler could be used to augment the usual filter and pump, or passive system presently employed to estimate personnel dose from radon daughters. It would also allow measurement of any combination of daughters from the three radon isotopes. Upon completion of sampling, the sampler is closed and removed from the mine. This sampler, with its liquid air contents maintained by the slow evaporation of liquid nitrogen, is taken to the place of measurement. There, the sampler is opened, the accumulation of water and ice in the neck is chiseled down into the liquid air, and the sample is transferred quickly to a precooled counting dewar (Fig. 2). This counting dewar is then placed upon a gamma radiation detector; we recommend a high purity germanium detector. A determination of all the radon daughters can be made in 1 to 4 hours after the sample is taken.

Jan 1, 1981

By Gerald P. Kelton

Over the past quarter of a century, the success of the hydrocyclone as a classifier in closed circuit grinding installations has permitted the introduction of the cyclone into virtually all fields of wet industrial processing. Research and experience gained in these applications have established the optimum cyclone sizes and designs necessary to provide the required performance. Although cyclones are used in widely diverse liquid-solid applications, their use for ultrafine separation clearly demonstrates the importance of a familiarity with previous case studies. Krebs Engineers is firmly dedicated to serving the process industry and has acquired the unsurpassed knowledge and experience to handle all types of separations and classification problems. Cyclones have been used for a number of applications to make what might be considered fine separations. A typical example is in an iron ore grinding circuit where a 381 mm diameter cyclone will classify an overflow product to 85% -44 micron. There is no question that this is a fine separation, but still finer separations are possible, and these are known as ultrafine separations.

Jan 1, 1983

By Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area. Applications in the minerals industries include calcium carbonate, talc, barytes, mica, diatamaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc. The basic principles can be extended to provide continuous drying and delivery of discrete particles from a wet process slurry. The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques. Mean particle sizes in the order of 1 micron are achieveable from pre-milled feeds, or maintained from similar slurries in the drying mode. Aspects of feed preparation and multi-stage processing are discussed.

Jan 1, 1983

By Kevin Fitzpatrick, Carmen Scalise, Patrick Jensen

"The Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) owns and operates the Tunnel and Reservoir Plan (TARP) system which was adopted in 1972. TARP is a network of 110 miles of deep tunnels and ultimately 3 large reservoirs to combat waterway pollution and flooding within a 350 square mile area served by combined sewers. The original TARP concept included additional tunnels to convey CSOs from the largest storms to the reservoirs. With the initial TARP tunnels complete and the reservoirs nearing completion, MWRDGC commissioned hydraulic and hydrologic modeling studies to analyze the benefits of additional conveyance tunnels. These updated studies optimized the configuration of additional tunnels considering integration with potential future local sewer system upgrades. The alternatives considered several routes of 25, 30, and 35 foot diameter tunnels, ranging from 10 to 18 miles. Alternatives were analyzed based on projected reductions to basement flooding compared to the relative costs. TUNNEL AND RESERVOIR PLAN After World War II the Chicagoland area underwent rapid growth and development. With the Metropolitan Water Reclamation District of Greater Chicago's (MWRDGC) service area becoming increasingly impervious, the flat Chicago landscape was increasingly at risk of significant flooding. In the mid and late 1950's, Chicago experienced multiple extreme storm events that had significant impacts on the city and generated the momentum necessary to initiate what would ultimately become one of the world's largest civil works undertakings. In 1957 a Flood Control Coordinating Committee was formed, consisting of representatives of the MWRDGC, Illinois Department of Public Works, Cook County, and the city of Chicago, to review various plans and develop recommendations for a course of action. With more than 50 alternative concepts being identified, the Tunnel and Reservoir Plan (TARP), which itself is a composite of various alternatives, was adopted the by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) in 1972. The need to adopt a long term plan was further influenced by the Clean Water Act, which was enacted only 8 days prior."

Jan 1, 2016

By James J. Scott

Longwall mining has not received a great deal of attention in the United States; however, this system offers many advantages over the conventional room-and-pillar methods now being used. In order to conserve the coal resources of this country, the U. S. Bureau of Mines has investi¬gated the feasibility of adapting European longwall mining methods to American coal seams. Their studies showed longwall mining to be well suited to thinner seams and, greater depths; and, in addition, permitted almost 100 percent recovery of the coal. Most, experiments with this method resulted in higher overall production-costs than were commonly obtained with highly mechanized room-and-pillar techniques This high cost-was largely due to the excessive amount of labor required to maintain adequate roof support with conventional longwall mining techniques. With the substitution of hydraulic-powered, self-advancing roof support systems for conventional supports, this excessive labor cost has been decreased, and longwall mining costs are now competitive with those of modern room-and-pillar mining.

Jan 1, 1964

By R. L. Teseneer

Pyrite samples from twenty-one locations in the North Carolina Slate Belt were analyzed for cobalt, gold, mercury, and nickel by atomic absorption spectrophotometry. The geographic distribution of relatively high values of certain trace elements in pyrite suggests that, in addition to gold, cobalt and nickel metallogenetic provinces are possible in the slate belt. Northwest trends of province boundaries may be genetically related to subsurface features rather than to surface geology. Within province boundaries gold and nickel exploration programs should be concentrated in areas containing intermediate to mafic tuffs, while cobalt may be more concentrated in argillites and phyllites.

Jan 1, 1979

By Edmundo Tulcanaza

Increasing exploration costs and the need to reduce the time-frame from exploration to production presently demand formalized procedures to assist exploration planning and reserve analysis. Exploration planning is basically required to select the most cost-effective drilling/sampling program, and to flag the needs for data of greater relevance and reliability. Reserve analysis is necessary to determine the sensitivity of grade-tonnage relations, and to clarify the economic implications of mining when alternative technical choices are to be considered.

Jan 1, 1982

By L. R. Hossner

Chemical and physical properties of surface soils and overburden materials must be evaluated prior to strip mining activities. This information can be used to assess whether subsurface overburden can be equal in quality to the existing surface soils, especially when these soils are classed as prime farm lands. In Texas, materials from the Carrizo, Calvert Bluff, Simsboro, and Hooper Formations overlie the lignite. The Carrizo Formation consists of thick clean sands with poor water and nutrient retention capabilities. These materials are least suited for placement of the surface of reclaimed land. The oxidized, medium textured overburden from the Calvert Bluff and Simsboro Formations possess adequate water and nutrient properties and are better suited for sustained plant growth. Non-oxidized Calvert Bluff and Hooper sediments generally have acceptable properties for reclamation. However, caution must be exercised in vegetating these materials since they may contain acid forming sulfide minerals.

Jan 1, 1982

By Ross W. Smith, Salim Akhtar

Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collect- ors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By Willard C. Lacy

Discovery of a mine is a complex affair. No mine is simply found but comes about through the efforts of many. It is difficult to establish "credit" when a mine is found and becomes a viable operation, or "guilt" when a mine is lost, goes bankrupt, or remains undeveloped. The story of the Toquepala and Cuajone developments entails various stages of: (1) discovery and recognition; (2) testing and innovation; (3) political and industrial negotiation and intrigue; and (4) finance, development, and operation. The Toquepala and Cuajone projects introduced innovative drilling techniques, were among the first major porphyry copper deposits to utilize induced polarization (1P)geophysical methods, were among the first deposits to undertake complete feasibility studies on drilled- out ore bodies, and were developed by the first large Western Hemisphere copper mining consortium. Many persons have contributed to the development of these two great deposits. Some of the names have been lost and certain contributions have gone unrecognized. I apologize for these omissions.

Jan 1, 1991

By M. Prasad, G. M. Rao, A. K. Majumder, T. C. Rao

Froth flotation was employed to beneficiate a lean-grade siliceous rock-phosphate ore containing fluorapatite, the phosphate-bearing mineral. The main gangue minerals were quartz, iron oxides and aluminum oxides. After the rougher stage, four cleaning stages were required to upgrade the ore. The liberation size of the phosphate mineral was below 200 mesh, The reagent scheme consisted of commercial-grade sodium silicate and sodium oleate. The effect of reagent dosages, number of cleaning stages and pulp density on the efficiences of separation were studied systematically. A flowsheet was proposed for the processing of low-grade siliceous phosphate ore containing 12.1% P2O5, 55.36% SiO2 and 15.45% CaO. The flowsheet provided a useable phosphate concentrate containing 34.18% P2O5 and 14.20% SiO2 with a P2O5 recovery of 70.4% (the weight yield was 25.0%).

Jan 1, 1999