Search Documents

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By G. Reed Marchant

In 1967 the US Congress passed the "Clean Air Act." This act was amended in 1970. As a result it soon became obvious that American industries were going to have to make significant changes in their methods of operation to be able to comply with quickly developing federal regulations. One of the first regulations developed was on sulfur dioxide. For this reason, the nonferrous smelting industry was immediately affected by these new regulations. This is true because the smelting process produces sulfur dioxide as a natural product of combustion when the sulfur-bearing ore is oxidized to purify the metal. The federal government's approach for setting standards included public hearings at which government, industry, and private citizens were allowed to make comments. For this reason, it was apparent to Kennecott's Metal Mining Div. that it was desirable to make a maximum effort in working with the agency to see that correct input was provided at the hearings to assist the government in setting fair and realistic standards. It was also obvious that more complete monitoring would be required. It soon became apparent that the efforts required input from many levels of the corporation from the chief executive to the plant operators. In order to accomplish both the administrative and the technical needs, an organization was needed that could respond quickly to these needs, obtain information from diverse sources, and bring it to focus in an organized approach to the problem.

Jan 1, 1979

By J. F. Dresser

Managing environmental compliance at a complex facility has the potential to bring a high degree of personal and professional satisfaction to both the corporation and the individuals responsible for day-to-day operations. The decade of the 1990's, however, has seen the emergence of a nationwide trend of aggressive federal and state civil and criminal enforcement for environmental violations. This trend, spearheaded by the U.S. Department of Justice (DOJ) and the U.S. Environmental Protection Agency's (EPA) Office of Enforcement, has the potential to place the corporation, its corporate officers, and compliance personnel at collective professional risk, as well as a growing tendency to place accountability on individuals. Management of environmental compliance has been anecdotally compared to a shooting gallery at a carnival, with the following exception: At the shooting gallery, successfully hitting nine out of ten targets usually brings a reward and recognition of shooting skill; hitting nine out of ten environmental compliance expectations not only brings agency consternation and negative publicity, but the "gallery" will likely shoot back with stiff fines and possible criminal allegations. Faced with the challenges of the new environmental compliance shooting gallery, corporations and professionals are often left asking themselves, "How do we (or more appropriately, can we) win at this game?" This paper examines recent federal enforcement statistics and offers several suggestions for coping with the responsibility of managing environmental compliance in the 1990's.

Jan 1, 1992

By W.J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 from New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be relatively widespread through much of the Tasman Fold Belts of Eastern Australia and production to date is estimated to be some 500 000 carats from a number of 'small alluvial fields. Despite extensive exploration though, no primary rock source carrying significant diamond contents has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia over the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives, of which 180 have been confirmed to be diamondiferous. Only one pipe however, the 1200 Ma high grade Argyle lamproite and associated near-by alluvials, has proved to be economically exploitable with current annual production of 40 million carats valued at approximately US$400 million. Production from the open-pit will be sustainable until at least 2003. This paper briefly summarizes the history of diamond discovery in Australia, principal diamondiferous provinces and deposits, current exploration activities and the potential for future discoveries.

Jan 1, 1995

By J. D. Goodrich

Success of The Carter Mining Company's safety program can be primarily attributed to "total immersion" of all operating and staff personnel in program design and implementation. Currently, the Company operates two surface coal mines in Campbell County, Wyoming. Total employment is about 440 and current annual production is about 15 million tons. The safety program has evolved from one which was administered primarily by staff personnel (the Safety Department) to one which requires active participation by line management and operating personnel. Lost time accident frequencies have declined from a high of 1.86 per 200K hours worked in 1978 to zero in 1982. Reportable accident frequencies have declined from slightly over 5 to slightly over 2 during the same period. Analysis of program results indicates that the most important achievement by the company has been to gain strong commitment to safe operation by all employees. It is important that program format and content be frequently changed and modified so that: 1) The requirement for safe job performance is communicated well and often, 2) The safe job performance message is trans- mitted in new and interesting ways, and 3) Operating personnel participate in design and implementation of the program.

Jan 1, 1983

By Werner Wenzel

Methods to increase the gas penetration through sinter layers. In the field of agglomeration, sintering has gained importance, specially in Europe; in Best-Europe this trend will continue till the year 1980, since it is quite probable that in the blast furnace burdens with 50-60 sinter, 10-20 % pellets and 20-25 % ore lumps will be employed. In order to meet this demand for sinter, new sinter bands with reaction areas between 300-400 m2 will be constructed. Chemical and physical phenomena during the Suction-Draught-sinter process. Iron ore sintering is generally considered as a burning process where the material contains 90-95 % ash i.e. non-combustible ingredients. Sintering represents a heterogeneous exothermic reaction in which the chemical phenomena as combustion, calcination, hydration, reduction and oxydation are superposed by physical phenomena. The physical phenomena are devided into material transport and simultaniously occurring heat transport processes. The velocity of these combined physico-chemical reactions i.e. the change in the reaction site per unit time determine the efficiency of the sinter process. The gas permeability as an important criterion of heat transport during the Suction-Draught sinter process.

Jan 1, 1971

By J. Kalnejais

Discovered in 1896, the Sons of Gwalia orebody was initially mined by unground methods. Euring the mine's uderground operations workings reached a vertical depth of 1080 metres. The same orebody is now being mined by open cut methods. The present operation mines a broad envelope of mineralisation surrounding old stopes, whereas the original underground operation concentrated on mining high grade parts of the Gwalia Lode System. Underground mining continued up to 1963 when operations ceased due to high operating costs and the low grade of ore mined. In 1984 a new company, Sons of Gwalia NL, commenced open cut operations.

Jan 1, 1989

By G. A. Hope, K. Watling, R. Woods, I. Chandra, I. M. Ritchie

This paper presents two aspects of gold leaching research and development. The first section of the paper covers the development of innovative gold leaching processes. The research in this area has concentrated on the development of new thiosulfate leaching systems which use Fe(III) stabilized by ligands as the oxidant in place of copper(II)+ammonia. The second section will cover the development of innovative techniques such as surface enhanced Raman scattering (SERS) to study the leaching of gold in cyanide solutions. It will be shown that the use of in-situ SERS yields information which cannot be obtained using other methodologies.

Jan 1, 2005

By E. Baliktsis

PPC (Public Power Corporation) operates a new power plant at the South-West part of Crete. Recently the extension of the Power Plant started. ATHENA SA the main contractor of the project assigned to EXORIXI SA the implementation of a blast vibration monitoring program and prevention-evaluation of risks caused by construction blastings inside or very close to the operating part of the power station. The blasting parameters and characteristic elements that had been evaluated, the measures that had been taken and materialized, the overall risk management and the results of the whole program are presented in this paper.

Jan 1, 2006

By James N. Grassby

Metal production has traditionally been a cyclical industry. 1977 in the base metals industry has highlighted that fact with a steady decline in the market place for base metals. Corporate aggregate planning is based on good forecasting and when changing conditions make that forecasting inaccurate, alternate analysis of schedules must be accomplished quickly. The computer is the only medium powerful enough to answer management's questions within an acceptable time frame. Worldwide communications networks now make it possible for the many multinational mining companies to arrive at coordinated corporate production plans based on similar basic data from several producing divisions. The Ontario Div. of Inco Metals Co., a unit of Inco Ltd., encompassed during 1977 14 producing mines, 2 nonproducing mines, 1 nonproducing open pit, 5 flotation mills, I smelter, 2 nickel refineries, 1 copper refinery, and an iron ore recovery plant. Several new mines are under development. Mine production approximates 63 500 tpd (70,000 stpd) from some 1000 workplaces. The need for longrange mine planning and scheduling is obvious and until recently has been satisfied by manual methods. However, while manual methods are often quite practical for a small number of mines, or for mines with relatively short lives, or for mines with only one mining method, the situation in the Ontario Div. is too complex and long-term to allow effective, timely planning by such methods. In 1967, a year after the first computer was installed in the division, work was begun on the computerization of the more than 30,000 borehole logs kept in the mines exploration files with a view to speeding up the assessment of mineral resources. Also in 1967 one of the first substantial systems developed on the main business systems computer was the monthly scheduling of development and production for all mines. This system encompassed tons productions per workplace, feet development per workplace, auxiliary and service activities and the requisite labor for each of these. These two dates are mentioned to show that concurrently with the acquisition of computers in the division there was an early understanding of the importance of automating mine scheduling and planning and of the potential for effective and useful computerization of such activities. In 1970, a pilot program was developed in one of the mines containing a large number of workplaces (350) to schedule the production on a network basis. Varying degrees of interest were shown by the individual mine engineers based on the complexity of the production planning problem at each mine. In an evolutionary process, mines were added to the system as its value became obvious in terms of time saving, flexibility, and accuracy. In 1975, the central mine engineering department decided that the system should be extended to all mines so that a complete division-wide long-range scheduling system would be available upon which to base development and production planning. This system would use basic ore data, allow the addition of scheduling commands, and calculate a schedule for the life of the mine. Many reports could be produced for each mine and all-mine summaries would also be available. The significance of the system can be stated in one phrase-speed, accuracy, and flexibility. Whereas in the past a long-range all mines schedule might have been done once a year, taking from two to three months, now it can be done in a day. The chief mines engineer can incorporate changes in input data and external constraints and call for a "new look" at the long-range schedule to assist him and mines production management in their decision-making processes. Using previous manual methods this could not be done quickly enough to be useful.

Jan 1, 1979

By Kurt Zeidler, Vojtech Gall

London Underground Limited are currently constructing an extension of the Jubilee Line. The approximately 16-km long Jubilee Line Extension Project connects the existing Green Park Underground Station with the Canary Wharf area and Greenwich. Being a part of the project, the London Bridge Station (Contract 104) was built using a combination of the New Austrian Tunneling Method (NATM) with Compensation Grouting. NATM was successfully applied in softground and urban areas under restrictive requirements regarding settlement limitation. Information on the flexibility of the method and the influence of Compensation Grouting on ground and tunnels are given.

Jan 1, 1997

By R. H. King, R. E. Cameron

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time-study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index- based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1991

By Odd G. Askilsrud, Steinar Johannessen

New powerplants, tunnels and dams are currently under construction at Meraaker to triple the annual power production of a nearly 100 year old power scheme. A total of 44 km tunnels with cross sections varying from 7 m2 to 32 m2 have been excavated in hard rock formations. Ten kilometers were excavated by a High Performance Tunnel Boring Machine (HP TBM). The remaining tunnels have been completed by the drill and blast method, using modem proven equipment and procedures. This paper gives special attention to the TBM drive and equipment selection, including, planning, site organization and performance.

Jan 1, 1993

By Liang Ruilu, Guo Lihua

In light of the properties on process mineralogy of the old tailings in a certain copper mine in the People's Republic of China, a new process of combined reagent and stepwise flotation is applied in which the flotation of copper sulfides is followed by the flotation of copper oxides. Recoveries of copper and associated gold and silver have been greatly increased. The tailings obtained were subjected to the gravitational separation-magnetic separation process to recover iron minerals. Tailings from iron separation are taken as fillers and sent to the pit underground. Thus, the secondary resources are comprehensively utilized.

Jan 1, 1995

By Victor F. Hollister

The great increase in post-World War I1 use of molybdenum was made possible by discoveries of that metal in porphyry molybdenum and porphyry copper deposits. This section documents significant porphyry molybdenum discoveries of the post-war period. The most important discovery was Henderson in Colorado. It is not only one of the world's largest and richest, but it was found by a team of geologists who defined the hood model and tested it successfully at Henderson. Under the leadership of Stewart Wallace, these scientists established a set of criteria for exploration for Henderson-type de- posits that was copied by the industry. The discovery bf vertical cylinder type porphyry molybdenum deposits was less renowned. Boss Mountain in British Columbia and then Mt. Pleasant in New Brunswick were given relatively scant notice, compared with the Henderson discovery. However, these deposits have geometrics distinct from that found in the typical hood, which directly affects their exploration characteristics. Mt. Pleasant, included in this section, is a well defined, near vertical breccia pipe. Both the Henderson and Mt. Pleasant discoveries were made by relatively small groups operating independently of the bureaucracy that characterizes large corporations. The management role in each case was one of encouragement. In addition, Wallace had the beneficial experience of working for Climax, whose objective was the discovery of porphyry molybdenum deposits. Henderson was the natural outgrowth of the exploration effort by those who studied and understood the Climax deposit.

Jan 1, 1991

By R. H. Mozley

It is not my intention in this paper to review recent developments in the mineral processing industry which might fall under the above heading, but to refer to some of the research that I have done over the past 25 years or so. To begin with then, my student days at the Camborne School of Mines, the year 1952. Equipment from the last century was still in everyday use at the local tin mines. At South Crofty Ltd a steam beam engine 100 years old was pumping mine water from 2000 feet, the motive force being conveyed from surface to the pump at the bottom of the mine by a 14 inch square pitch pine rod joined with forged iron straps, steam winders were still in use, and in the mills, stamps ground the ore, and the cassiterite was recovered by equipment with exotic names like "buddies, kievs, and round frames." And to equip us students for the brave new world, we included in our practical mineral dressing a day's test programme with a Californian stamp -- experience that I am still waiting to put to good use!

Jan 1, 1984

By H. D. Sharma

INTRODUCTION Uranium mill tailings, by-products from the mining and milling of uranium oxide contain all decay products of uranium-238, uranium-235 and all the Th-232. The ore containing all daughter products of the parents U-238, U-235 and Th-232 is ground to approximately 50% under 200 mesh particle size and after extraction of uranium, the residue, described as tailings, is discharged into natural depressions confined by dams. These deposition sites are referred to as tailings ponds. Tailings ponds are located in two mining districts, Bancroft and Elliot Lake in the Province of Ontario, Canada. Some parts of tailings ponds are dry up to a depth of several meters, whereas other parts have a water table very close to the surface and still others are covered with water. The extent to which the daughters of uranium isotopes are in equilibrium with the parents U-238 and U-235 is dependent on the age of the deposit in which uranium occurs and the extent to which the decay products are removed by geochemical processes. In the mining district of Bancroft, the deposit is known to be approximately 1 billion years old, whereas in Elliot Lake, the deposit is considered to be approximately 2 billion years old. The ratio of radiogenic lead isotopes Pb-206 and Pb-207, can provide some estimates concerning the age of the deposits. If the tailings are not affected by geochemical processes, the tailings would contain all the daughters of the 4n+2 and 4n+3 series in equilibrium concentrations. The equilibrium activities of some members of the 4n+2 series are calculated in Table 1. [ ] The amount of radiogenic stable lead isotopes depends on the age of the ore deposits. If the deposit in each district is of the same age, a definite relationship is expected with respect to the activity of Pb-210 and the radiogenic stable isotopes. Approximately 33 million tons of the tailings have been deposited in the early 1960's, approximately 20 years ago. During this period of storage, the segregation of uranium daughters, like radium, the diffusion of gaseous product, Rn-222, and removal of precursors by geochemical processes, can cause dis-equilibrium. Earlier work concerned with the uptake of Ra-226 and Pb-210 by plants (Kalin and Sharma, 1981), indicated that the concentrations of Pb-210,in samples of the tailings taken, were lower than the expected equilibrium. The diffusion of radon from a variety of matrices has been studied (Tanner, 1964). It has been shown that the diffusion coefficient is dependent on the particle size in which its precursor is present, the moisture content and the surface conditions. The direct measurement of radon concentrations in the environment near the ponds is dependent on the metereological conditions. Kramer, Schroeder and Evans, 1964, have examined the variations in the concentration of radon near the ground level with respect to atmospheric variables, such as changes in barometric pressure, precipitation, wind velocities, thermal atmospheric instability. It is difficult to relate the total release of radon from the ponds to the atmosphere over an extended period. Our measurements of Pb-210 and total lead on tailings samples taken from 16 sites indicate that the ratios of the activity of Pb-210 to the mass of total lead can provide parameters which are helpful in the estimation of the total amount of radon and its decay products diffusing from the tailings ponds. In this paper, we present the results of measurements of activities of Ra-226, Pb-210 and total lead in samples from various ponds situated in both mining districts. The measurements were confined to samples taken at 0-25 cm depth from the surface.

Jan 1, 1981

By Harry J. Fitzgerald

During World War II mining machinery manufacturers were limited in the development of their product improvement programs. Following the war, however, the ideas and intentions of both the users and manufacturers of mining equipment became evident. The Coal Industry launched a series of events which indicated their determination to rise to the economic challenge of developing profitable machines which would eliminate the out-dated and back-breaking methods of mining previously used. Two major technological advances were developed as a result of the ambitious goals forecast by the Coal Industry: 1. Coal mining was going "off-track" and concentrated mining operations were to follow in rapid succession. 2. Carbide tools provided the remaining missing contribution to another technological breakthrough....Continuous Mining. Little did the inventors realize the significance of the misnomer they created because twenty-five years later the industry is still striving to secure the results implied by the meaning of the word...."Continuous". Nevertheless, all major manufacturers embarked on programs in an attempt to compete for recognition in this new mechanized-mining endeavor Eventually in 1950 there were three types of boring machines and two types of ripping machines being manufactured. Mining Speed was the desired goal.

Jan 1, 1970

By Hans von Michaelis

Very little has been published about Cia de Minas Buena­ventura. Don Alberto Benavides Quintana, now in his seventies, founded the company in 1953. This venerable gentleman is a Doyon of the Peruvian mining industry and more has been known about him than about his company. Buenaventura is a highly profitable gold producer with excellent potential to expand gold production in joint ventures with Newmont, Southern Peru Copper (ASARCO), and BRGM as well by developing their own new gold mines. On September 15, The Wall Street Journal published an article titled "Peru's Big Rebound Sets Off Foreign Investors' Enthusiasm."

Jan 1, 1995

By Ronald Ludchak

Since coal has been designated as the short-term answer to the threatening world energy crisis, improved surface mining techniques, along with improved extraction and handling equipment, are needed to increase the amounts that can economically be mined by open pit methods. A dwindling supply of low cost oil and gas have dictated a major rethinking of our energy sources and their use. New methods for open pit coal mining have to be found to increase coal production and to meet more stringent reclamation laws. Modern twin-engine elevating scrapers can play a vital role in meeting these needs. They are readily available, with short delivery times, from several experienced manufacturers of earthmoving equipment. Recent developments of the elevator system have extended its working range to include many of the materials commonly encountered in open pit mining. The paper deals with the advantages of using twin-engine elevating scrapers in the performance of various mining tasks. These tasks range from utility work to the major task of using the scrapers as a primary stripping toot and, of even more importance, a stripping- reclamation tool for, with scrapers, the overburden can be moved and redeposited in the same strata sequence or soil horizon as in its natural state. A recap of current applications of the elevating scraper will be presented, along with proposed uses.

Jan 1, 1975