Search Documents

By Madan Kumar Annam, Hari Krishna Y

"Basement construction is one of the challenging geotechnical concerns in the urban environment. Several types of retention systems are practiced to support the earth which is suitable for restricted access, rapid mobilization, fast excavation and cost-effective designs. A thorough understanding of geotechnical engineering as well as the structural mechanics is important for the earth retention systems. This paper discusses a project with various types of foundation solutions including monitoring of deflections during excavation stage of a retention system.A multi storeyed residential building (3B+Stilt+18F) in Chennai having structure foot print area of 1500 m2 has to be constructed on large diameter pile foundations and also to support the proposed basement excavation. Ground water table was encountered at about 6m below the existing ground level (EGL). In order to support heavy structural loads, large diameter bored cast-in-situ piles were chosen and installed. Further, complete retention system was economically designed and built, which includes installation of Contiguous Bored Piles (CBP) in combination of vertical grout columns behind CBP wall to seal the gap between the CB Piles, installation of inclined ground anchors, construction of capping beam, stressing and locking of installed ground anchors. A detailed monitoring program was in place and continuous monitoring of wall deflections is being measured at the time of publishing this paper. This paper describes the design and construction aspects adopted for foundation and retention system including the monitoring results during excavation stage of the project.INTRODUCTIONIn general, stage wise open excavation will be opted for basement construction where plenty of space is available. Due to urbanization and restricted space, open excavation became a difficult task nowadays. To overcome this problem, suitable retention system need to be selected to retain the soil mass. Selection of suitable retention system for multi-level basement excavation is a great challenge in geotechnical industry, especially when the proposed site is located within the minimum set back distance from the existing structures. This in turn calls for the advanced and innovative methods of retention system.Several earth retention systems such as Diaphragm Walls, Secant Pile Walls, CBP system, Soldier Pile Walls, Sheet Piles, Deep Soil Mixing (block walls) etc. with or without inclined ground anchors are being practiced worldwide. Considering the advantages and disadvantages of the available retention systems in practice locally and keeping in view of present site conditions, the developer has chosen CBP system with inclined ground anchors so that all foundation related works of the project will be handled in a single package. The main advantage of such packaged solution will ease the coordination between design consultants and foundation contractor resulting in faster construction of foundation works which in turn reflect savings in time and cost."

Jan 1, 2015

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner's belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By Richard Morland

Some simple and fundamental objectives To challenge and inspire our people to embrace safety as a value ?A stand for safety as a value ?A stand for our people ?A stand by our people ?Prevent harm to our people ?Eliminate suffering for individuals, families, friends, colleagues

May 1, 2010

By Q. X. Yun

This paper provides a new approach to optimize the production planning in underground mines by means of evolutionary algorithms. Firstly, genetic algorithm is used to reach the global optimization in planning. Then, evolutionary programming is employed to obtain the partial optimization for each year. The application proves that the new approach is reasonable and useful. Keywords: Evolutionary algorithm, Genetic algorithm, Evolutionary programming, Optimization, Mining engineering.

Jan 1, 2003

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006

The functional design of a pavement relates to the selection of appropriate wearing course materials which optimise the trafficability of a pavement. Trafficability is dictated to a large degree by the choice, application and maintenance of locally available wearing course materials. Poor functional performance results in decreased safety and operational efficiency and increasing road and vehicle maintenance requirements. An optimal functional design will include a certain amount and frequency of maintenance (watering, grading etc.) and thus maintenance itself can be planned, scheduled and optimized within the limits of required road performance and minimum vehicle operating and road maintenance costs. Since no wearing course material selection guidelines, tailored to the specific needs of surface mines, were available, there was the need to identify appropriate selection guidelines for the range of materials commonly encountered for road building on South African mines. The aim of this paper is to present an overview of the functional design method for mine haul roads and, through an analysis and quantification of existing wearing course material performance, to recommend appropriate wearing course material selection guidelines. The functional design technique has been applied at a number of mines and is illustrated by an application case study which demonstrates the potential reduction in total transportation operating costs associated with the optimal functional design.

Jan 1, 2000

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By D. K. Chibwe, P. Taskinen

"This investigation consists of a numerical and physical modelling exercise on flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a 0.2-scale cold model of an industrial Peirce-Smith converter (PSC). Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The 2D and 3D numerical simulations were carried out using volume of fluid (VOF) and realizable k-e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions. Measurement of mass transfer indicated that fluid flow in the PSC is stratified. Blowing configurations and slag volume both had significant effects on mixing propagation, wave formation, and splashing.As a potential process alternative to increase conversion efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined as well as lateral blowing conditions, and the results of the combined concept are encouraging."

Jan 1, 2015

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By Stephen C. Tadolini, Thomas M. Barczak, Paul McKelvey

A new generation of hydraulic mine support prestressing devices has been developed. These thin-walled steel shells are machine-welded and can be inflated with water or any liquid to provide prestressing for a wide variety of roof support products ranging from Can supports to props and cable bolts. With an expansion capability of several inches, depending on the geometry and size of the unit, they can also establish roof contact eliminating the need for wooden wedges or crib blocks that are commonly employed with several standing roof support products. Capable of withstanding pressures from 1,000 to 6,000 psi, these cells are able to transfer roof loading into the support structure without rupturing. A recent development has been the addition of an inexpensive yield valve that provides control of the maximum pressure and load development on the support. This paper examines the performance capabilities of these inflatable prestressing units and the impact they have on the performance of various support systems, including an evaluation of the overall stiffness of the support system and the load control during yielding of the prestressing unit. Recommendations are made regarding the design requirements of the prestressing unit to optimize the support performance. A summary of mine applications using this technology is provided with general comments regarding their impact on ground control.

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990

By Z. Zhang, R. G. Reddy

Experimental and thermodynamic modelling studies on the structure of alkali borate melts and properties are discussed. A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of composition. A qualitative interpretation for the boron anomaly in viscosity has been proposed, which regards the boron anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosity of alkali borate melts increases or decreases according to the changes in rigidity and spatial connectivity of the glass network structure, which is the function of temperature and composition. These concepts with some key examples are discussed in relation to their usefulness and practicality in industrial slags. Keywords: alkali borate melts; structural model; activities; structural groups; viscosity;

Jan 1, 2004

By Marco Antonio Falquete

A novel spark-generating tube, containing no explosive in its composition, is evaluated and compared with conventional shock tube. The product overcomes a series of problems found in conventional shock tube technology. The technologic development had multiple aims: to avoid transport and storage costs associated with explosives, to be more environmental-friendly, to obtain a high-velocity, hightemperature spark whose thermal performance could overcome poor heat transfer to the delay charge by gas convection at shock tube end, and that could cross barriers such as tight kinks, close knots, cuts, extreme environmental conditions, and long-term hot explosive emulsion exposure. The product of this development is evaluated and compared with conventional shock tube in a series of aspects and performance tests, including spark thermal performance (ignition of tougher, low sensitive delay columns, spark gap test), propagation in critical conditions of use (kinks, knots, cuttings), extreme environmental conditions (long-term exposure to hot emulsion explosive, extremes of cold, heat, moisture, underwater exposure), safety features (ignition through flame, open fire), and security against terrorist acts. Due to the safe characteristics of the tube, a series of demonstrations will be performed during the presentation. In nearly all tests and aspects, the spark-generating tube exceeds conventional shock tube, and in the rest equals shock tube, making it a more reliable alternative.

Jan 1, 2005

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

U.S. Minerals Coordinating Council Advised. -The Critical Materials Act of 1981, H. R. 4281, introduced on July 27, would create a Council on Critical Materials in the White House Executive Office to oversee Federal materials programs involving $1 billion committed to research by 14 agencies, and to serve as the President&apos;s focal point to evaluate materials policy. It was introduced by Congressman Fuqua (D-Fla.) whose Committee on Science and Technology has over-sight over the implementation of P. L. 96-479, the National Materials and Minerals Policy, Research and Development Act of 1980. Bulgaria&apos;s Mineral Bank. -Recently Bulgaria established a mineral bank to facilitate receipt of foreign credits for exploiting Bulgaria&apos;s mineral raw materials. The bank has wide powers to enter into business arrangements with foreign creditors. Bulgaria&apos;s main interest in trading with the West is to import the technology for developing energy and mineral resources.

Jan 1, 1981

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995

By Pierre Lacombe

"The operation of the Louvicourt Mine will have to rely on stringent grade control and on the optimization of the amount of blocked ore made available per given development effort. All of the above being necessary to obtain the highest throughput at the lowest mining cost.To assist in achieving these objectives, the need for production of a competent fill with short curing time was recognized early by the project partners. As well, operating costs associated with the selected method should be as low as possible while meeting the technical criteria.A feasibility study comparing filling methods showed potential benefits in all aspects of the paste fill use, except for its higher capital costs and increased operational complexity. This last consideration was tackled by the conservative design approach adopted in the flowsheet development of the paste fill plant.Since commissioning of the plant has just been completed at this time, the paper will focus on the feasibility study and its background, the design of the plant and testwork results at pilot plant and plant scale.RésuméLe succès de l 'opération de Louvicourt Mine dépendra d' un contrôle serré des teneurs du minerai et de la maximisation de la quantité de minerai développée par effort uni ta ire. Ces critères devant etre respectés afin d'obtenir le taux de production le plus élevé au coût le plus bas.De façon à satisfaire ces contraintes, les partenaires du projet ont reconnu tôt la nécessité de produire un remblai de qualité tout en maintenant un temps de curage court. De plus, les coût d'opération associés a cette opération se devaient d'être des plus avantageux sans sacrifier l'atteinte des objectifs techniques.Une étude de faisabilité comparant différentes méthodes de remblayage a démontré que le remblai en pâte offre des aspects positifs sous taus les angles, si ce n'est de son coût en capital initial élevé et de sa complexité relative d'opération. Ce dernier point fut considéré de près par l'adoption d' une approche conservatrice lors de la conception de l'usine de rernblai.Puisque la mise en service de l'usine n'a été faite que les détails de l 'étude de faisabilité et ses fondements, 1 'usine et des résultats d' essais obtenus a l'échelle de l'usine seront discutés."

Jan 1, 1995

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931