Search Documents

Despite the media's use of the mining industry as a whipping boy over its perceived attitude towards the environment, the facts remain that the only legislated requirement in the SA Statute Books for any form of environmental impact-assessment prior to development is to be found in the Minerals Act in the form of an EMPR. Not only is our industry complying with this requirement, but moves are afoot to set up environmental management systems for existing operations in preparation for seeking accreditation under ISO 14001 when published towards the end of this year. On how broad a front are we advancing? ? Is the industry equipped to handle these challenges? ? Does it have the determination to overcome its problems? ? Do we realise that failure may mean the loss of markets overseas to competitors who can meet the international standards? ? Where are the shortcomings and when must our efforts be focussed?

Jan 1, 1996

By H. Kenworthy

"INTRODUCTION ..Although the occurrence of iron ore in Missouri was recognized by Marquette as early as 1673, the first known mining and smelting operation was conducted in 1815. This operation was near Arcadia, Iron County, the first of its kind west of the Mississippi-Ohio River system. Several small furnaces of short life were erected in Missouri in the ensuing 30 years. However, until the extensive deposits of Iron Mountain and Pilot Knob were opened between 1843 and 1850, the state remained a minor producer of iron. It was this district which was chiefly responsible for the prominent position Missouri held in the iron industry until the late 1880's. At this time the easily minable high-grade ores became exhausted and the discovery of the immense Lake Superior deposits depressed the raw-ore price to such an extent that any mines ceased to operate. 3/Small yearly production of iron ores continued in Missouri to the present. Owing to war demands for hard ore suitable for open-hearth steel, the M. A. Hanna Co., through its subsidiary, the Ozark Ore Co., reopened the Iron Mountain, deposits and installed new equipment in an old concentrator to handle the low-grade ores left from previous operations. At present, ore production is from open pits, but underground mining is contemplated in the future. About 2,000 tons a day of iron ore is treated by gravity concentration of material from the open pits in the immediate vicinity. The concentrate is shipped to the Birmingham, Ala., district and to Granite City, Ill., for smelting. The coarse tailing is sold for ballast and concrete aggregate. The iron requirements of the concentrate stipulated by the purchaser are not difficult to meet, but the phosphorus is frequently higher than desired. For 1946 the concentrates averaged 54.18 percent iron and 0.235 percent phosphorus with low sulfur. The Ozark Ore Co. concentrate, however, sometimes contains as much as 0.40 percent phosphorus. The phosphorus in ores from those portions of the deposits wherein the phosphorus occurs with siliceous gangue is readily rejected in the milling, but in much of the ore the phosphorus is associated with the iron and concentrated with the iron minerals. Selective mining is impossible owing to the spotty occurrence of the phosphorus mineral. Often within 5 feet the ore will change from low phosphorus to high phosphorus, and it would be expedient to find a method of rejecting enough phosphorus at the mill from the latter type of ore to meet the phosphorus specification."

Feb 1, 1948

Two years ago I was sitting in a big lecture theatre at the School of Mines in Kalgoorlie at the annual New LeadersÆ Conference listening to a guy tell us all how much he loved his job, travelling the country ælegallyÆ blowing stuff up à and getting paid to do it. I would have paid to see and do the things he spoke of à now IÆm that guy. From finishing a mining engineering degree at the University of Ballarat, through the job hunt, to firing environmental blasts in Tassie and designing and implementing construction blasts in the middle of the Gold Coast. My name is Rohan Stevens and IÆm a blast-o-holic. While the æjob huntÆ we all embark on toward the end of our degrees is a stressful time, itÆs also very exciting in the current climate. There are a number of things I have learnt through both my hunt for the job that best suited me and working for the worldÆs largest explosives manufacturer. If at least you donÆt benefit from my learnings IÆm certain you will enjoy hearing about (and viewing) some of the work I have had the opportunity to be involved with over the last 18 months with Orica Mining Services.

Jan 1, 2008

This Bureau of Mines report and its companion report (Information Circular 9143) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of mining of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the casts for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mining unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. Coverage for surface mining includes dredging, quarrying, strip mining, and open pit mining. The underground mining includes individual development sections for drifting, raising, shaft sinking, stope development, various mining methods, underground mine haulage, general plant, and underground mine administrative cost. This system can be used for estimating cost data for an undeveloped deposit or for checking or verifying mining costs from a developed deposit, with a minimum amount of background information.

Jan 1, 1987

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in more intensified efforts in inspections of coal refuse sites. Inspections, however, are mainly qualitative and time consuming. In August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photointerpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Bibliographies of literature reviews in the area of past coal refuse embankment failures, monitoring instruments and methods, and photogrammetry are included.

Jan 1, 1977

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modelling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. Three-dimensional numerical direct shear tests were conducted on the coupled FD-DE model of the combined rock-cemented rockfill (R-CRF) specimens with the frictional-bonded interface. With the microstructural parameters determined, the macro-mechanical properties of the interface of the coupled model were calibrated to well fit with the theoretical values of the combined specimen under the direct shear condition assumed according to the Mohr–Coulomb strength criterion. Evident elastoplastic shear behaviour was observed on the interfaces, and excellent agreement was attained between the shapes of the theoretical and simulated shear stress-displacement curves of the coupled models at different servo-controlled normal stresses. Particulate-scale force chains inside the DE model of the CRF specimen were highly consistent with the force contour on the FD model of the rock specimen, demonstrating the shear stress evolution of the coupled model at different shear displacements. Parametric studies verified the effects of the deformation properties of the interface parallel bonds on the shape of shear stress-displacement curves of the coupled models. The test results validated the feasibility and rationality of the coupled FD-DE method for modelling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modelling experience for investigating the shear behaviour at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

Nov 2, 2021

By N. Iverson, E. Haft, V. T. McLemore, M. Woodard, E. Owen

Present and emerging technologies are renewing interest in domestic rare earth elements (REE) production. REE deposits throughout the North American Cordilleran alkaline-igneous belt are being re-examined for their economic potential. In New Mexico, the mineral deposits found in this belt are associated with Eocene–Oligocene alkaline to calc-alkaline igneous rocks. Four areas in New Mexico have been examined for their REE potential. The chondrite-normalized REE patterns are similar for all four districts, even though different REE minerals are found. Crandallite, xenotime, bastnäsite and brookite are found in fluorite veins and carbonatites at Laughlin Peak. Bastnäsite was extracted during fluorite processing from 1954-1980 from the Gallinas Mountains, where samples as high as 8% total REE are found in fluorite veins. Other REE minerals include agardite, parasite, xenotime, and monazite. Allanite, thorite and as much as 8133 ppm total REE are found in fluorite veins in the Capitan Mountains. In the Cornudas Mountains, exploration along the outer edge of the Wind Mountain nepheline syenite laccolith and within phonolite dikes, plugs, skarns and carbonate-replacement deposits in Chess Draw contain as much as 3110 ppm TREE, hosted in eudialyte, monazite, bastnäsite, and calciocatapleiite.

Feb 1, 2023

By B. J. Moore

This publication contains analyses arid related source data for 274 natural gas samples from 20 States. Of the total samples, 269 were collected during calendar year 1985; the reminder were collected earlier, but releases granting permission to publish were not received before 1986, All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1987

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

Large scale mining of Mesabi taconites may have moved nearer to realization with the arrival of the latest model Linde Jet-Piercing machine at Reserve Mining Co.'s Babbitt, Minn. property. When the machine is placed in operation it is expected to pierce blast holes in the hard taconite beds up to 10 times faster than is possible with existing drilling equipment. The new primary blast hole drilling machine has been designated the JPM-3, and is the successor to the JPM-1, in operation at Erie Mining Co.'s taconite mines at Aurora, Minn. The size of primary blast holes which can now be pierced has increased from a nominal 61 in. diameter to 71 in. diameter and maximum hole depth has increased from 35 ft to 47 ft. Development has progressed to where 71/2 in. holes can be pierced with the same speed as 61/2 in. holes. Piercing progress is controlled by electronic blowpipe descent controls. Other features of the JPM-3 include: automatic burner ignition from the operating cab; heated and air conditioned operating cab designed for all-year operation; mechanical improvements for sub-zero operation common to the Mesabi, and redesign of wearing parts for longer service with minimum maintenance. The 40-ton machine is self-propelled. Power, oxygen, and cooling water lines trail from the machine. Jet piercing is based on combustion products of oxygen and a liquid fuel such as kerosene. The flame, jetting from a burner at speeds of about 6000 ft per sec, disintegrates layers of spallable rock. The burner is cooled by water which is then directed through orifices around the periphery of the burner. The water changes to steam and carries the spallings out of the hole. The equipment used in Jet-Piercing is essentially a tractor-mounted blowpipe containing a combustion chamber and nozzle, which is in effect a miniature rocket motor, from which the supersonic combustion gases emerge to do their work.

Jan 1, 1952

By V. Labiouse, R. Gärber

The paper aims at clarifying the up-to-now misappreciated role taken by pore water on the design of deep tunnels in saturated porous media. Numerical simulations with a non-dimensional FEM-model emphasise the influence of pore water characteristics (in situ pressure and compressibility) and boundary conditions (lining permeability) on the short and long term underground-structure equilibrium states. These results cannot be achieved by means of monophasic total stress analyses. Dieser Beitrag untersucht den Einfluss des Porenwassers auf die Dimensionierung von tiefen Tunnelbauwerken in wassergesättigtem Untergrund. Numerische Simulationen mittels eines dimensionslosen FEM-Modells betonen den Einfluss der Porenwassereigenschaften (in-situ Druck und Kompressibilität) und der hydraulischen Randbedingungen (Tunnelausbaudurchlässigkeit) auf Kurz- und Langzeitverhalten des Untergrund-Ausbau Gleichgewichts. Diese Ergebnisse können nicht ermittelt werden anhand von Einphasen- und Totalspannungsmodellen. L’article s’intéresse au rôle méconnu de l’eau interstitielle dans le dimensionnement de tunnels profonds creusés dans des milieux poreux saturés. Des calculs adimensionnels par éléments finis soulignent l’influence des caractéristiques de l’eau interstitielle (pression in situ et compressibilité) ainsi que des conditions aux frontières (perméabilité du revêtement) sur les équilibres court et long terme de l’ouvrage. Ces résultats ne peuvent pas être obtenus par des calculs en contraintes totales.

Jan 1, 2003

The Pittsburgh (Pa.) and Spokane (Wash.) Research Laboratories are among the world?s foremost mining research establishments. Once a part of the former U.S. Bureau of Mines (USBM), which was abolished by the U.S. Congress in fiscal year 96, health and safety research at these laboratories was transferred to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is the Federal agency responsible for conducting research and making recommendations for the prevention of work-related illness and injury. The Institute is part of the Centers for Disease Control and Prevention within the U.S. Department of Health and Human Services. Over the past two decades, the Pittsburgh and Spokane Research Laboratories have produced sustained technological achievements in mining health and safety, including? ? Development of novel respirable coal dust control technologies and more effective monitoring techniques to reduce worker exposure to hazardous mine dusts. ? Improved ground control technologies to warn and protect miners from the dangers of coal mine roof collapses and other hazardous strata conditions. ? Improved ergonomic design criteria and training methods to protect mine workers from injuries and fatalities associated with equipment and manual tasks. ? Development of enabling technologies that allow miners to control their mining equipment from a physically safe, protected work area away from respirable dust, harmful noise levels, and roof collapses. ? Improved mine fire detection and extinguishment techniques. ? Development of smaller, lighter, and safer emergency breathing devices.

Jan 1, 2007

By Zara Hosseini

?Microseismicity ?Seismic Systems ?Intrinsically Safe and Explosion Proof Seismic System ?Case studies: ?Gas Drainage Optimization ?Fault Identification ?Conclusion Seismic Event ?Occurrences in which energy is released in the rockmass creating a series of seismic waves propagating throughout the rockmass ?Can cause a Fall of Ground or CoalBurst Factors creating Seismicity: ?Mining at Depth ?High stress zones ?Major geological structures ?Mining practices and strategies ?Mining activities i.e. drilling and blasting

Aug 1, 2013

By R. H. Bedford

"The El Dorado copper mine is situated in the foothill copper-zinc belt of California, which traverses the western slope of the Sierra Nevada with unusual persistence from Butte County to Kern County, a distance of more than 300 miles. Although this area contains such important past producers as the Penn mine, Union, and others, a great part of the current production has been derived from smaller properties, which depend largely on premium metal prices for economical operation. The El Dorado mine is in the latter group, which constitutes an important source of metal in a national emergency.Exploration by the Bureau of Mines by means of eight diamond-drill holes Indicated narrow, intermittent lenses of copper ore along structures boo feet in length. The copper occurs in massive sulfides composed of chalcopyrite, pyrite, pyrrhotite, and minor quantities of bernite. The sulfides have evidently replaced tuffs, which are interbedded with the Mariposa slates and shales.H. A. Weiler and Hal T. Hall, owners of the El Dorado copper property, requested an examination by the Bureau during the latter part of 1914. In December of that year an engineer of the Bureau of Mines visited the mine and recommended the project work undertaken. The purpose was to aid the owners in bringing the property into production of copper and zinc, which at that time was critically essential to the war industries.Complete factual data obtained by the exploration are embodied in this report.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G, Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Acknowledgment is made to A. O. Johnson, chief, Reno Division, Mining Branch, and Lowell B. Moon, chief, Mining Branch, for their aid and direction."

Jun 1, 1946

By Oliver Bowles

"Simple systematic accounting that adequately records all transactions has long been regarded as essential to the welfare of any business enterprise. Some of the defects that detract from the prosperity of the slate industry are attributable to a lack of effectiveness in cost keeping. This condition has prompted the United States Bureau of Mines to make a detailed study of accounting methods for the slate industry, and to present for consideration a system of accounts, which it is believed would enable the industry to attain more economical management and operation if accepted by a fair proportion of its important units.The method of accounting presented herein has been worked out with the assistance of leading slate producers and the recommendation are tentative and are submitted in this form as a means of developing constructive criticism. Believing that cooperative effort in this, as in many other problems, will bring the most enduring benefits to the industry as a whole, the writer urges that the most earnest consideration be given to this vital problem now facing the slate industry.Grateful acknowledgment is made of the helpful assistance rendered by R. E. Eckert of the accounting firm of Eckert, Degan, and Palmer of Easton, Pa., in compiling the charts and the explanatory text. He has brought to this work a wide knowledge of accountancy, supplemented by a background of direct contact with the slate industry, and his presence at the various conferences has been of great advantage in clearing up difficulties. The National Slate Association sponsored the cost study and chiefly through the efforts of President W. H. Smith and Secretary W. S. Hays, has aided greatly in conducting it. Acknowledgment is also made of assistance rendered by William F. Marsh of the United States Bureau of Mines."

Nov 1, 1929

By Y. C. Kim, F. Szidarovszky

G.M. Philip and D.F. Watson The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write : "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accu¬mulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common. ? References Journel, A.G., 1986, "Geostatistics: models and tools for Earth Sciences," Journal of Mathematical Geology, Vol. 18, No. 1, pp. 119-139. Philip, G.M., and Watson, D.F., 1985a, "Theoretical aspects of grade-tonnage calculations," International Journal of Mining and Geological Engineering, Vol. 3, pp. 149-154. Philip, G.M., and Watson, D.F., 1985b, "A deterministic approach to computing ore reserves. I, Grade Estimation," Earth Resources Foundation, Occas. Paper 2, The University of Sydney, 24 pp. Philip, G.M., and Watson, D.F., 1987a, "Neighborhood discontinuities in bivariate interpolation of scattered observations," Mathematical Geology, Vol. 18, No. 1, pp. 69-74. Philip, G.M., and Watson, D.F., 1987b, "Estimating interactions of topological functions," Mathematical Geology, Vol. 18, (at press). Reply by Y. C. Kim Before replying to the comments by Philip and Watson, it is desirable to establish the original perspective of our paper, which was intended primarily for the practitioners of mining who possess a working knowledge of ordinary kriging. The paper tried to convey the following practical points: (1) there are circumstances in which one observes negative weights, (2) illustration of circumstances under which one can expect negative weights, (3) should one obtain a negative estimated grade, one can resort to elimination of negative weights using the technique outlined in the paper, and (4) one could normally select only the first layer of surrounding assays to estimate the block grade. Under such a perspective, most of the comments by Philip and Watson are irrelevant and misdirected. For example, the practitioners do not find it difficult to "interpret" the results of ordinary kriging, as evidenced by the fact that they have been using the results for nearly a decade. Nor are the practitioners concerned with discontinuities in estimated block grades due to changing neighborhood of assays during kriging. What matters to the practitioners is the fact that kriging does provide the best estimate among all the estimation tools available to them as of today. ?

Jan 2, 1987

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

By David Schlain

"IntroductionThe purpose of this investigation was to study the characteristics of the high-acid electrolytic manganese cell with the idea of fitting it into one of the flow sheets being worked out by the Metallurgical Division of the Bureau of Mines for the recovery of manganese from low-grade domestic ores.In construction, the high-acid cell 3/ differs from the low-acid type in that the cathode and anode compartments are separated by a diaphragm of relatively low porosity, such as alundum. This is necessary because in the high-acid cell the two electrolytes are circulated separately. The anolyte is 15 to 30 percent H2SO4. The catholyte consists of a solution of ammonium sulfate and manganese sulfate with a OH of 4 to 3. The only mixing of electrolytes is that resulting from flow through the diaphragms. In the low-acid cell the two electrolytes are not circulated separately and do not differ so widely in hydrogen-ion concentration. Hence, the canvas diaphragm is sufficient.During operation of the cell, manganese is deposited on the cathode, and sulfuric acid is produced in the anode compartments. Various other reactions take place in the cell. There is considerable decomposition of water; hydrogen is evolved at the cathode, and oxygen is liberated at the anode. When lead anodes are used, some hydrated oxides of manganese are formed at the anodes. The quantity of oxides formed is not as great as it is in the low-acid cell, because fewer Mn++ reach the vicinity of the anodes."

Jul 1, 1942

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

By N. Arbiter

The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter ratio. This is in spite of the fact that practice varies substantially in this area: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia; historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to/the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills; on the occurrence of the overload phenomenon; and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape face or is of major importance in this area; and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type.

Jan 1, 1990