Search Documents

JAMES A. BARR Consulting Engineer Mt. Pleasant; Tennessee Washington, D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia LENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.

Jan 1, 1952

[JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Montieello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

JAMES A. BARR Consulting Engineer Mt. Pleasant. Tennessee Washington. D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Callf.

Jan 1, 1952

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By S. C. Borah

Graphite, a mineral form of pure carbon, is one of the most versatile minerals in industry, because of its varying physical properties and characteristics. The mineral occurs naturally in the form of tubular crystals or microcrystalline earthy lumps, or it is disseminated in rocks, which have undergone intense metamorphism. India has a large deposition of graphite minerals out of which about 43% are found in Arunachal Pradesh. However, compared to the rest of the country, the North-East Region and particularly Arunachal Pradesh has not attracted attention till date for detail investigation for characterization, beneficiation, prospecting and/or exploitation of the mineral resources including graphite. Bulk graphite sample were collected from upper Subanshiri district of Arunachal Pradesh. Chemical analysis of the representative samples were carried out and found that 7.29%, 19.60% and 6.07% of fixed carbon (FC) is present in graphite sample collected from La-Lamdak, Bopi and Taliha, Arunachal Pradesh, respectively. Chemical analysis of the ash of the graphite sample shows presence of impurities such as silica, Al2O3, Fe2O3, Ca, Mg etc in the graphite sample which are also supported by XRD and SEM-EDX investigation. The graphite samples of Arunachal Pradesh are low grade and do not fulfill the market requirement for the industrial applications. Therefore, low-grade graphite is subjected to beneficiation for the upgradation of the graphite for industrial applications. We have adopted the dispersion?cum-settling technique for the beneficiation of the graphite sample collected from Arunachal Pradesh. The FC of 40.21% with 41.17% raw graphite recovery which is equivalent to 71.02% carbon recovery have been obtained by gravity separation technique using only distilled water without any chemical reagent in case of graphite sample collected from Bopi, Arunachal Pradesh. The graphite sample is upgraded up to 47.75% FC with 41.91% raw graphite recovery, which is equivalent to 85.85% carbon recovery with the pH adjustment at 9 with NaOH. Keywords: graphite, beneficiation, gravity separation, arunachal Pradesh

Sep 1, 2012

By Warren E. Morrison

The first major evaluation of the nation's raw materials prospects after World War II was completed by the President's Materials Policy Commission (Paley Commission) in 1952 and submitted to the President in June of that year, as a five-volume study entitled Resources for Freedom. The bulk of the report was devoted to an analysis of the past, present, and probable future of the Nation's mineral supply industries. The Commission's evaluation of the future situation regarding minerals was derived from its forecasts of the probable domestic demand for the major minerals in the 1970's. This demand analysis was made in the context of probable worldwide demand. Several crucial assumptions were made by the Commission's fore-casters. It was assumed in 1950 that the next 20 to 30 years would see no major wars and be a period of sustained economic growth. Another assumption was that the anticipated demand for raw materials must be supplied at essentially no increase in real cost in order to avoid crucial supply problems. The Commission's forecasts were derived within the context of the country's expected future rate of economic activity. The gross national product (GNP) growth to 1975 was derived from projections of the number of people in the labor force, hours of work, and an index of probable production measured per unit of labor input. It was believed labor hours would decrease and labor productivity would increase. The result was a forecast GNP growth rate of 3 percent.

Jan 1, 1970

By Frank Pepe, Nestor Garavelli

The 2023 Rapid Excavation and Tunneling Conference (RETC) will be held in Boston, MA and will include the presentation of 133 papers divided into 20 technical sessions during the 3 day conference that were selected from over 200+ papers that were submitted to the committee. The selected papers are included within this book to provide a comprehensive recap of the conference while also providing a source of reference for contractors and engineers in the future. The selected papers will include contributions from all divisions of the tunneling industry plus risk management and best contract practices. Boston is known to the tunneling industry for its complex and difficult tunneling history, specifically of recent memory the Central Artery/Tunnel Project also know as the “Big Dig” of the 1980s and early 1990s. The selection of Boston as a host city was fitting from a historical perspective and as avenue for the city to present its upcoming tunnel projects. RETC began in 1972 with the idea of sharing ideas, design and project construction experience, and new technology, between contractors, designers, owners and suppliers. The ability to provide a single location every other year for all facets of the tunneling industry to gather and discuss the aforementioned was and still is viewed as a way to help the tunnel industry grow. The lessons learned from completed projects, the advancement of technology which could be implemented into design and the presentation of new projects by owners/designers and contractors allows for the limits and complexity of upcoming projects to be expanded beyond our current capabilities. Our industry has never been as busy as it currently is, and we are seeing more future projects coming out for solicitation across all business sectors. With the good fortune that all of us have been blessed with one of the biggest challenges that we have been faced with is the shortage of future management on all levels for our projects including the labor force. We all want our industry to continue to grow and succeed, our most important assets are the people that we employ. Investing in the education and continued training of our work forces to be up to date with the latest technology and methods is the key to our success. This also includes develop, recruiting and mentoring of young students graduating college to join our industry so that we can all continue to grow. We hope that all those attending the conference will have the ability to attend as many sessions as possible and to expand their network within our industry. As in past years, scholarship students will be in attendance and we encourage all to offer these students an opportunity to visit jobs, attend learning sessions or future internships to expand their interest in our industry that needs an injection of young engineers to contribute and lead our future Rapid Excavation and Tunneling Conferences. The program chairs wish to thank the session chairs, co-chairs, authors, and other members of the RETC Executive Committee for their dedication to this conference. Last but certainly not least, we give special thanks to the SME staff for their hard work and enthusiastic support in making this conference possible.

Dec 1, 2023

By César Bernal M

El presente trabajo busca establecer el mejor plan de explotación de la mina Cobriza a través del nuevo proyecto de expansión. El plan de explotación señala que los ciclos de explotación, el número de tajeos requeridos por el método de corte y relleno, la selección del equipo de mina, así como los servicios auxiliares para suministrar el tonelaje necesario de mineral a la nueva planta de Coris.

Nov 8, 1982

U.S. Bureau of Mines contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment", was an investigative effort involving: ? Study of the fire problem on large mobile mining equipment ? Identification of equipment most prone to fire, to serve as a design case example ? Design of an improved fire protection system ? Demonstration of the developed system This effort was performed during the period June 1972 through May 1973, and was conducted in two phases. Phase I, June through November 1972, was devoted to identifying the fire problem and developing and evaluating design criteria. Phase II involved translating the design into hardware and demonstrating its effectiveness during actual fire tests, first on a wooden mockup of a truck, then on an operating truck at a working mine site.

Jan 1, 1973

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

Law of the Sea. - The Ninth Session of the Law of the Sea Conference resumed July 28 at Geneva and will run for 5 weeks. The 160-nation Conference began in 1973. Two of the major factors to be discussed are the transfer of technology to the UN-controlled Enterprise or mining authority, and how the 36-member Council will make decisions. As the session completed its third week, delegates expressed little hope of completing a treaty text this year. There was a feeling, though, that substantive issues might be settled so that a treaty text can be completed next year. The Deep Seabed Hard Mineral Resources Act signed by the President on June 28, provides an interim regulatory procedure for ocean mining activities conducted by U.S. nationals that may be superseded by a law of the sea treaty.

Jan 1, 1980

On November 9, the Reynolds Metals Company cut production by 12 at its primary aluminum smelters at Troutdale, Oreg., and Longview, Wash., as a result of an earlier 25% power cutback by the Bonneville Power Administration due to lower than normal stream flow in September, the Aluminum Company of America had closed one potline at its Vancouver smelter because of the power cutback. Nearly 700 union workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., walked off the job when their contract expired or, November 15, after rejecting a proposed 3-year contract. The smelter has an annual capacity of 180,000 tons mid accounts for 50% of Anaconda's aluminum production. No talks are scheduled.

Jan 1, 1979

By M. Ataee-pour, S. E. Jalali

So far, a large number of algorithms have been developed for the optimization of pit limits, most of which follow deterministic rules. In this paper, a new algorithm is introduced, which follows a probabilistic logic using the Markov chain process. The algorithm is implemented on a transition matrix that corresponds to the 2D conventional economic block model of the mining area. The probability of mining a block is proportional to the desirability it may provide. Applying this algorithm, the probability of mining each block is obtained, and finally, the optimum pit limits are defined as the pit, which provides the highest probability of mining. In order to validate the proposed model, a numerical example is given and the results of the algorithm are compared to those of a dynamic programming algorithm. A 2D analysis of the problem is discussed in this paper. Although dealing with 3D problems requires larger size matrices, the optimization method is the same and the algorithm does not need any smoothing.

Jan 1, 2006

By Michael A. Piepenburg

The East Side Access (ESA) Project will extend Long Island Rail Road (LIRR) into midtown Manhattan via 11 km of tunnels, a new terminal station and associated support facilities. In addition to the hard-rock tunneling currently underway in Manhattan, soft-ground tunnels in Queens will traverse beneath Amtrak?s Sunnyside Yard and Harold Interlocking, the busiest rail interlocking in North America. This paper details ESA?s coordinated approach to interfacing with both Amtrak and LIRR with regard to the planned tunnels, shafts and related construction beneath or adjacent to the operating railroads. This interface includes integration of railroad staff, extensive presentations, reviews and agreements with the railroads regarding settlement mitigation, real-time automated geo-instrumentation monitoring, ground improvement, and geotechnical/environmental controls.

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting, and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power input over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge that was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified 'chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2012

By Hazel J. Stratton

IN THE HALF-CENTURY that has passed since the Bureau of Mines was established in July 1910, the research and technologic investigations conducted by the Bureau's scientists, engineers, and other personnel have helped significantly in improving health and safety in the mineral industries and have contributed substantially in conserving the Nation's mineral resources through improved techniques in the mining, treatment, and use of mineral commodities. From Bureau laboratories have come new materials for industry and better methods of extracting and processing minerals and mineral fuels. Bureau safety investigations-complemented by equipment testing and by programs of mine inspection and education-have brought about safer and more healthful working conditions.

Jan 1, 1960

By Luís Marcelo Tavares, Marko Hilden, Malcolm Powell, Grant Ballantyne, Lian Liu

The t10 relationship developed by Narayanan and Whiten has underpinned a number of the JKMRC models and the characterisation of ore competence through impact testing with the drop weight tester. This usefulness is based on a consistent relationship between the t10 value and the overall size distribution that was noted for brittle rocks. However, like all characterisation tests this should be used only when the controlling conditions apply, which in this case is single impact breakage between two metal platens and within the range of sizes in which fragment sizes are normalizable. For any other mode of breakage the relationship should be confirmed before being applied. Soft ores or bimodal ores with widely different competence between dominant components have non-typical breakage signatures. Breakage via single point impact abrasion, compressed-bed breakage, low-energy surface breakage and incremental breakage, to name some of the other breakage modes, do not obey the general t10 relationship, so their outcomes cannot be used to provide a direct comparison. Inappropriate use of the t10 parameter can result in misleading conclusions about efficiency of energy use. These issues and alternative comparison techniques are presented and discussed in terms of choosing appropriate measures of efficiency of breakage, ore competence and energy required for comminution.

Jan 1, 2014

By Silvio Hernández Aquije

El presente texto señala el descubrimento del yacimiento vanadífero de Minasragra a través del reporte de Yeatman-Berry en 1916 y el de Kett-Sproul en 1931. Así también señala los tipos de mineralización como la mineralización primaria y por impregnación.

Jul 1, 1955

By A. R. Barnes, N. Stubina

Increasingly, gold producers are forced to treat ever more refractory ores. While ores containing pyrite, arsenopyrite and carbonaceous material have been subjected to complete pressure oxidation (PDX) as the standard process for such ores, recent improvements in fluid bed roasting technologies have led to a resurgence of interest in roasting as a viable alternative. The lower capital and operating costs of roaster installations add further impetus to this trend. The Extractive Metallurgy Group at Xstrata Process Support operates four fluid bed reactors of various sizes which have been utilised on a large number of projects to treat highly refractory ores. Preliminary mineralogical modelling of both the physical and chemical aspects of the roasting process and subsequent testing under carefully controlled conditions has allowed clients to obtain gold recoveries approaching or matching those achievable by PDX. The flexibility of the units to operate in various modes- " bubbling bed", circulating bed, two stage, sub-stoichiometric and combinations of these, and the range of sample sizes accommodated, from a few kilograms to a few tons, has enabled XPS to accommodate clients with a wide variety of gold bearing refractory ores from all over the world. This paper outlines the key challenges of fluid bed roasting of refractory gold ores, describes the methodology used to design the testwork program and provides some results from select test campaigns.

Jan 1, 2011

By Marcello M. Veiga

Informal gold mining operations in the Amazon emit about 100 tonnes of mercury annually because of poor amalgamation practice. Lack of information and the complexity of mercury transformations hinder effective action to prevent such pollution and/or monitor its extent. In the past, mathematical equations have been formulated to deal with the correlation of natural variables and mercury in biota but often, the error range is too great to provide useful models. Projection of physico-chemical variations in an environment subjected to mercury emissions onto the extent of bioaccumulation is fraught with many uncertainties and unknowns such as internal correlations between variables and the site-specific nature of biota contamination. Often assumptions about closed systems are invalid when applied to natural environments. This work presents a heuristic approach to this problem in which amalgamation methods and natural variables are dealt with using an IF-THEN rule-based system that concludes about levels of emission and risk of bioaccumulation. The system is able to handle uncertain or vague data and yet still provide useful output. Belief in mercury oxidation or dangerous conditions are examined using Fuzzy Logic techniques and Inference Equations. These belief levels are derived from thermodynamic equilibrium data together with field observations of natural variables. This procedure can reduce the need for sophisticated analytical equipment and can provide information and diagnosis to non-technical people.

Jan 1, 1994