Search Documents

By C. Hellar

A new dual-boom remotely controlled roof bolter was designed, fabricated, and then tested in an underground coal mine. Remote-control functions allowed complete bolting cycles to be performed on two booms with both operators located within protective cabs. Capabilities included 3-to 6-foot-long bolts in 5-to 8-foot seams, limited to bolts 20 inches shorter than seam height. Machine was in compliance with all regulations including dust collection, machine lighting, and permissibility.

Jan 1, 1979

The contract for the Water Jet Chock Mounted Miner Feasibility Study was awarded to FMC Corporation's Advanced Products Division on 18 November, 1974. The program was divided into four phases as follows: ? Phase I - Planning ? Phase II - Conceptual Design ? Phase III - Budgetary Cost Estimate and Economic Feasibility Study ? Phase IV - Final Report During Phase I, which lasted 1 month, most of the necessary information and data for the conduct of Phase II was obtained. To accomplish this, arrangements were made for personal visits to the University of Missouri at Rolla, Illinois Institute of Technology Research Institute, USBM TCMRC, Alpine Equipment Co., Mining Progress, Inc. and Eastern Associated Coal Corporation's Harris No. 1 Mine. Also, a list of manufacturers of high pressure equipment was compiled to be contacted during Phase II. Finally, the objectives to be accomplished during Phase II were outlined. The Phase I Report was submitted on 23 December, 1974. At the beginning of Phase II, personal visits were made to the research centers and firms mentioned above. Later an additional visit was made to the Harris Mine, and to the Pittsburgh Mining Research Center at Brucetun to observe a test of a water jet mounted on an Alpine Mining Machine. Equipment manufacturers of high pressure components such as hoses, tubing, valves, pumps, and intensifiers were contacted to obtain item performance data, availability, and cost.

Jan 1, 1975

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 196'), under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures Dr. Henry R. Linden, Director, Institute of Gas Technology and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 1965, under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures. Dr. Henry R. Linden, Director, Institute of Gas Technology, and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

The treatment plant at Martha Mine was upgraded from a nominal throughput of 110tph (O.93mtpa) to 150tph (1.25mtpa) late 1999. Post-upgrade performance did not meet expectations when treating either the competent primary ore or the clay-rich oxide ore.   ò Plant throughput is constrained by milling capacity when treating the competent primary ore. This is not an issue at present as current plant feed is oxide ore from the top of the open-pit, but will become so in future years as the pit deepens. To counter this future threat, ball mill power has been restored to 1100kW through modifications to the drive train. The addition of a crushing circuit may also be necessary.   ò Plant throughput was originally constrained by thickener and leach/adsorption tank issues when treating the oxide are. Changes to plant equipment and operations has seen the removal of these constraints and throughput on this material is no longer a problem.   The most significant issue facing plant staff at present is the high silver grade and its impact on gold recovery. These high grades impact upon recovery through losses caused by insufficient leach and adsorption capacity. To counter this, the geology, mining, and milling teams are working together to blend the high grade silver zones with lower grade ores - this is seen to be the quickest and most cost effective way to deal with the issue. The plant design has also been evaluated with a view to modifying it to cope with the higher silver grades. The viability of these modifications will depend on cost and time (that is, the length of time to implement any modifications versus the length of time to mine out the high silver zones).

Jan 1, 2001

By A. Karadogan, G. Tuncer, A. Kahriman

Determination of optimal blast parameters have been the priority act for blasters on the field due to financial and technical properties of the operation. Therefore many researchs were done to establish a general formula for many years. These intends could reach some empirical and numerical design frames consisting the rock, geology and explosives properties. Blasting parameters have to be adjusted according to the desired fragmentation rate especially on the mines where particle size distrubition after blasting has a great importance. Therefore the blast designs have to be evaluated considering the particle size distribution after the blasts. The Kuz-Ram model which was modified by Cunningham is one of the tools for estimating the particle size. Although it doesn’t give an accurate result, it can be very succesful on modifying the blasting design parameters by establishing a back correlation between the blasting parameters and the exact particle size distribution results which can be easily achieved by digital image processing system. Within the scope of this study, the particle size distribution after blasting was assessed by Split-Desktop digital image processing system and bench blasting parameters were studied considering the desired particle size distribution at Espey colemanite mine using Kuz-Ram and digital image processing system combination to determine the specific blasting parameters for this site.

Jan 1, 2005

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By L Barrere, J P. Sykes, A Trench, R S. Davies

Western Australia (WA), alongside Brazil, has remained at the forefront of the global seaborne traded iron ore market for over 40 years. Despite this apparent stability and strong market position, WA continues to face strong external international supply-side competition, mainly from Brazil, but also periodically from often marginal, non-traditional sources of iron ore. Additionally, WA iron ore supply has undergone significant decadal change internally, both of an evolutionary (brownfields expansion) and revolutionary nature (major new greenfields projects). Since 2006, a new generation of WA-focused iron ore explorers, developers and producers have emerged.The majors, BHP Billiton and Rio Tinto, have expanded mine production to record levels and the Roy Hill project is now approaching nameplate capacity. Fortescue Metals Group (FMG) is, however, the largest new market entrant of the last decade, delivering upon their vision of becoming the ‘new force in iron ore’. Unlike most of the other new WA market entrants, FMG’s operations are substantive. Most of the other smaller, new WA iron ore miners have struggled during the period of falling prices, though it is worth noting that collectively they have made a material supply-side impact during the price boom – typical of marginal supply. Finally there have been some contributions from new magnetite projects, however, the delivery and economics of these projects have not met expectations.In this paper, we touch briefly upon the key global market changes of the last decade, namely China-driven demand growth and the changes to the pricing mechanisms for iron ores – before reviewing the rise in WA iron ore supply in response to these markets. We finish by focusing on the most significant WA-focused supply-side development of the last decade, the rise of FMG as a major new supplier and the strategic situation that facilitated its rise. The unprecedented China-led rise in iron ore prices felled many traditional barriers to market entry into an oligopolistic industry, allowing many new market entrants (in WA and around the world). However, the downturn in iron ore prices resurrected these barriers to entry, with only FMG (thus far) breaking the entry barrier with significant scale. Difficult corporate decisions have been forced upon the smaller WA iron ore miners who, in some cases, will now struggle to further expand, or indeed continue to operate in the longer run.The changes that have taken place over the last decade of WA iron ore production hold insights for other emergent mineral commodity exports from the state. Successful market entry, even when industry barriers are high, does not always require an immediate low-cost production assumption alongside a strong balance sheet. FMG could see a new market, within an established commodity market, target an appropriate and new product at it, overcome temporarily-felled barriers to entry in infrastructure and finance, then innovate and aggressively cut costs ensuring it was behind the barriers to entry when they rose again after the price boom.CITATION:Barrere, L, Trench, A, Sykes, J P and Davies, R S, 2017. New generation Western Australian iron ore – strategic insights far beyond the Pilbara?, in Proceedings Iron Ore 2017, pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Gerald Whittle

What is Enterprise Optimization? Releasing value through better planning decisions: Philosophy, Methodology, Software The key to 5% -35% increase in enterprise value (NPV) The culmination of 25 years development in optimization for the mining industry ?Jeff Whittle Simultaneously optimizing: ?all steps in the value chain ?all assets in the enterprise portfolio ?all periods together

May 1, 2010

As far as is known at the present time, important ore occurrences at Mount Isa are restricted to the Urquhart Shale. These occur at Mount Isa itself, and some 13 miles north along strike at the Northern Leases.The primary silver-lead-zinc and copper orebodies occur as adjacent but discretc entities in lithologieally distinct host rocks. The copper orebodies occur in an envelope of "Silica Dolomite", whereas the silver-lead zinc orebodies occur in shale typical of the Urquhart Shale in general.At both Mount Isa and the Northern Leases, secondary lead orebodies occur at thc surface representing primary stratiform silver-lead-zinc sulphide accumulations in the fresh rocks at depth.Secondary copper orebodies are known only at Mount Isa, where they have formed in favourable environments, but unlike the secondary lead orebodies, not in the positions of the former primary mineralization that gave rise to them. The secondary copper is localized in shale remote from the point where the copper was released into solution by weathering. It was derived from very low grade fracture fillings and disseminations of chalcopyrite in the outcropping or suboutcropping crest of the "Silica Dolomite".Primary silver-lead-zinc orebodies arc oxidized without significant transport or secondary enrichment, but secondary copper orebodies arc characterized by considerable transport and extreme secondary enrichment.The original water table stood at approximately 1,150 ft (mine datum) and for the majority of the mine area controlled the base of complete oxidation fairly closely.An oxidized zone approximately 175 ft deep is general in the Urquhart Shale.Structures affecting ground conditions have influenced oxidation and leaching of the silver-lcad-zinc orebodies, and have had effects vital to the formation of secondary copper orebodies.

Jan 1, 1966

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000

By B Crossley

Self-cleaning fluidised bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. Recent advances in equipment design have increased the scope of application to include indirect heat transfer in slurry environments, including fouling, scaling and viscous slurries. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve heat transfer problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials may be used.

Jan 1, 2004

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014

By Donald Strickland, Peter Kresin, Dave Hall

"Have your parents or grandparents ever tried to share with you their wisdom and you ignored it because it did not relate to you‘? I have been ignorant and inevitably grew older and wished I had listened. The result: learning the hard way. As British Astronomer Fred Hoyle once said. “It is the true nature of mankind to learn from mistakes not from example.“ Hopefully we will continue to learn from the examples shared by our fellow mineral processors in these conference proceedings. It is the intent of this paper to share wisdom from the Musselwhite Mine that you may apply to your own operation.This paper is divided into three sections:1. Feasibility3. Operation3 . DesignKey points of the Feasibility and Design stages are summarized. followed by an analysis of actual operating statistics. An attempt is made to relate these statistics back to the feasibility and design with emphasis on areas of success and those with potential for improvement."

Jan 1, 1999

By K. P. Fournier

This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of vis cosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090-1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers. l-6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment. 1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7'8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverettg equation for a radial system:* This is sometimes referred to as the Lagrangian form of the displacement equation. If the injection water is at some temperature Ti which is above reservoir temperature TR, then lw, the flowing fraction which is water, is a function of both water saturation and fluid temperature at any given time and position in the reservoir. The temperature dependence of lw results from the temperature dependence of the viscosity ratio µo/µm of which lw is a function. Thus:

Jan 1, 1966

Drilling in the south of the Rapahoe Sector at Greymouth Coalfield has demonstrated the existence of thick coal seams in the upper Rewanui Member. Seam correlation is handicapped by complex lithostratigraphy and laterally variable geophysical log profiles. An integrated investigation of coal measure stratigraphy, coal petrology, and proximate analyses, suggests a feasible model whereby most of the major seam intersections belong to a single horizon. Coal properties vary laterally in response to original swamp conditions, which are believed to have ranged from well-drained to ponded. A new model of peat accumulation is proposed for the northern Rapahoe Sector, whereby Upper Rewanui peat accumulation occurred on a flood plain between the levees of a major south southwest-flowing fluvial system in the east and the toe of a western alluvial fan.

Jan 1, 1985

The interaction between ore-bearing fluids and the siliciclastic rocks typically hosting orogenic gold deposits in Phanerozoic metamorphic terrains result in the development of a distinctive alteration halo. Along with petrological changes such as the replacement of chlorite by carbonate and the growth of sericite, characteristic geochemical modifications take place within this alteration envelope. These include variations in elemental abundances and more or less pronounced shifts in the H, C, N, O, and S isotopic signature of the ore system. æFingerprintingÆ these isotopic trends can provide exploration with additional vectors towards the ore zone, and yields valuable information regarding the source of the hydrothermal fluids and the solutes contained therein. Data from radiogenic isotope systems such as Sr-Rb, Ar-Ar, Xe-Ra, Pb-Pb, Re-Os, Sm-Nd, and U-Pb can constrain the kinematic history of ore-hosting structures, provide important clues concerning the absolute timing of gold emplacement, and enable the detailed characterisation of associated intrusives with respect to their magma source(s) and crystallisation age. Although high analytical costs, long turn-around times and the potential for misinterpretation prevent isotope systems from offering a æquick & dirtyÆ analytical method that would provide a significant advantage in exploration for orogenic gold mineralisation, the development of integrated four-dimensional ore genesis models depends heavily on constraints obtained from isotope mass spectrometry.

Jan 1, 2002

By W. C. A. van Niekerk, M. H. Fourie

The carcinogenic potential of chromium (VI) has been the subject of numerous environmental and occupational studies, from which many regulatory efforts emanated. Besides the regulation of levels of known toxic substances (e.g. Cr (VI)), the classification of dusts for regulatory purposes has thus far depended on broad definitions of particle size, mainly used to distinguish only between inhalable and respirable particles. In the past, ultrafine particles (less than 0.1 µm diameter) (PM0.1) were often regarded as a non-issue, because it was believed that significant doses would not deposit in the lungs. A growing body of scientific data is indicating that ultrafine particles are more toxic than their coarse counterparts. Increased toxicity can be related to the unique dosimetric aspects of the deposition and disposition of inhaled ultrafine particles. Secondly, ultrafine particles have a larger surface area per given mass. The increased surface area can act as a carrier for co-pollutants, specifically transition metals (including chromium) that could form a coat on the particle surfaces during particle formation. This suggests that the presence of ?inert? ultrafine particles in the environment may enhance the potential for exposure to reactive airborne compounds, including Cr (VI). These factors are particularly important when information on occupational epidemiology is interpreted. It is desirable to consider the particle size distribution, for example when occupational exposure to hexavalent chromium compounds is assessed. Since ultrafine particles are more toxic than coarse particles with the same chemical composition, it could be speculated that cancer slope factors might be related to particle size distribution. This is relevant not only to carcinogenic chromium compounds, but also basically for any particle-associated toxicants. In general, the probability of developing health effects associated with occupational toxicants is likely to be higher when these are associated with the ultrafine particle range.

Jan 1, 2004