Search Documents

By C. A. Mitke

During September, 1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft mere found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2, CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97", and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were tested for air circulation and air tightness and the injector mas tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering these different tests, are illustrated in the catalogue and circulars of the company. After the above tests had been made on the oxygen apparatus, the men still complained about leaky helmets. Small quantities of gas entered the helmets and could not be detected by these methods. The

Jan 1, 1914

These pages may be used as order sheets. Mark the number desired opposite title of pamphlet wanted, add your name and address, tear out the sheets and mail them to us. Single orders 25 c. Pamphlets 10 c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlets of the same or different titles, when cash accompanies order. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long, as the supply lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets-that have been published by the Institute. Any other paper published by. the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare. The, Institute is still selling back volumes of Transactions at reduced prices, but some of these volumes are becoming rare. and members who desire to complete their sets of these very important books on mining and metallurgy are advised to send in their orders as soon as convenient. The attention of members is also called to the bibliographical index of the science of ore deposits contained in the Emmons Volume which is selling at $3 in paper and $4 in half morocco. The Posepny Volume is already exhausted and members who do not get in their orders for the Emmons Volume at the present reduced price may soon find themselves unable to obtain it on such favorable terms.

Jan 7, 1917

By J. B. Clark, A. S. Yue

IN recent years, zone melting1 has been applied extensively to the purification of metals having a very low vapor pressure.2-4 This note describes the zone melting of a high vapor-pressure metal, magnesium, where the melting takes place inside a refractory surface skin. The effects of zone speed and the number of passes of the molten zone on the purification have been determined and the effective distribution coefficients for the principal impurity elements were calculated. A schematic diagram of the zone-melting apparatus is given in Fig. 1. The Vycor tube containing the graphite boat with its magnesium charge (an extruded rod—3/8 in. in diam, 10 in. long) is pulled through the stationary furnaces. A molten zone approximately one-fourth the length of the charge is produced under each of the two central furnaces. Two grades of magnesium were studied—electrolytic magnesium and magnesium with a very low alloy content. The spectrographic analyses of these materials, within * 5 pct of the values stated, are given in Table I. Molten magnesium will vaporize severely if protected only by an inert atmosphere such as argon. Consequently an enveloping container is required. In zone melting, a rigid opaque container surrounding the charge is inconvenient because visual control of the zone length is prevented. A more satisfactory container is a strong flexible skin on the surface of the metal charge which is capable of supporting the molten zone. SO2 reacts with magnesium to form a thin coherent surface film of MgSO, and MgO. An atmosphere of SO, of commercial purity was maintained during the zone melting. Enough oxygen was present within the system and the commercial SO, for the satisfactory formation of the protective skin, so that any rupture of the skin during the zone refining was healed immediately.

Jan 1, 1959

By William L. Fink, Dana W. Smith

Many investigators have attempted to determine the true nature of the internal changes taking place during aging. Merica, Waltenberg and Scottlt were the first to propose a theory of age-hardening. They attributed the age-hardening of duralumin to the precipitation of minute particles of the compound CuA12. Later Zay Jeffries and R. S. Archer2 augmented the above theory by suggesting that the small CuAl2 particles acted as "keys" causing "slip interference." Many other investigators3 have devoted much time to the mechanism of age-hardening, some corroborating the "precipitation" and "slip interference" theory, others coming to different conclusions because of effects that to them seemed unexplainable by the early theories; e.g., the increase of electrical resistance upon aging, the fact that no change in lattice parameter could be detected during the early stages of aging even at elevated temperatures, and the fact that the density did not change as would be predicted. In 1932, Merica revised4 his earlier precipitation theory to take care of these presumably anomalous effects. This revised theory, the "knot" theory, assumes that substantial age-hardening occurs before actual precipitation of solute as discrete particles. The assumed mechanism is one of diffusion of solute atoms into groups forming distorted regions which act as "hard" spots and cause slip interference. These "knots" are assumed to have approximately the same lattice arrangement as the solvent. The anomalous behavior of lattice parameter, density, and electrical conductivity, require a modification of the simple precipitation-hardening theory, only if it is assumed that the precipitation of minute particles during aging has the same effects on these properties as the formation of large particles under equilibrium conditions. Data obtained by the authors in the study of the aluminum-magnesium system5 indicated that

Jan 1, 1936

By Charles Barrett

PLASTIC flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following funda-mental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the lattice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals -"grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by vari-ous investigators for more than 25 years, ? yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of mate-rial that was used in the earlier compression experiments1-hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Sidney Siegel, J. Gardner Brooks, Irvin R. Kramer

IN 1942 Grossmann1 proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigators2-5 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent [ ] upon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a hite quench than predicted by Grossmann's factors for an infinite quench (Table I). [ ] Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Grossmann's grain-size correction curves, deter- mined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1946

By D. A. Martin, Laird Crocker, W. I. Nissen

The Federal Bureau of Mines has developed a process for removing SO2 from stack gases. The process comprises absorption of SO2 in an. aqueous solution of sodium citrate, citric acid, and sodium thiosulfate, followed by reaction of the absorbed SO2 with H2S to precipitate sulfur and regenerate the citrate solution for recycle. A pilot plant was operated at The Bunker Hill Co. lead smelter in Kellogg, Idaho, to assess the feasibility of using the process for flue gas desulfurization. Nominal capacity of the pilot plant, which treated .tail gas from the lead smelter sintering furnace, was 1699 standard meters cubed per hour (15 degrees celsius) of 0.3- to 0.7-percent-SO2 gas yielding about 272 net kilograms of sulfur per day. The pilot plant was operated for about 4500 hours and produced more than 45 net tonnes of sulfur. The operation demonstrated that (1) more than 95 percent of the SO2 could be removed from the lead smelter sintering furnace tail gases, (2) regeneration of the citrate solution with H2S and precipitation of sulfur in conventional stirred vessels was readily controlled and highly efficient, (3) the precipitated sulfur could be continuously recovered as a 99.5-percent-pure product by kerosine flotation and melting, and (4) the 77- to 79-percent-H2S gas used for sulfur precipitation could be readily produced from pilot plant product sulfur, natural gas, and steam. Projected operating costs, including capital charges, for a citrate plant, installed at a 118 000-tonne-per-year lead smelter and treating 49 271 standard meters cubed per hour of lead smelter sintering furnace tail gas, are estimated to be $384 per tonne of sulfur.

Jan 1, 1976

By Nicholas J. Grant, Laszlo J. Bonis

Two dilute nickel alloys in each of the systems Ni-Al, Ni-Ti, Ni-Cr, and Ni-Si u:ere internally oxidized at 700° to 900°C for time periods up to 100hr to establish the oxide particle size, depth of oxide penetration, and the change in oxide particle size with depth. Fine (-270) mesh alloy powders were then intevruzlly oxidized, hydrogen sintered, compacted, and extrmded, yielding bar stock for tensile tests at room temperature and creep-mpture tests at 815° to 1093°C. Recrystallization studies were made up to 1400OC. ReCENT studies have clearly indicated that oxide dispersion strengthened alloys exhibit outstanding elevated temperature properties, espe- cially in long-time tests. Certain structural parameters must be observed to achieve optimum properties, namely, micron or submicron interpar-ticle spacing, submicron oxide particle size, and a high level of stored energy.'-5 A number of processes have been utilized to obtain the desired structures, but certain of them appear to offer greater promise. Thus far the most promising method is the internal oxidation of dilute alloys consisting of a relatively noble solvent metal and a readily oxidizable solute element.3'6)7 Several important principles governing internal oxidation have been established in earlier studies;' however, these principles are as yet not adequate to permit alloy development studies. Much of the earlier work was performed on relatively coarse wires or in idealized systems. As a result, there are still a number of unanswered questions which require considerable additional work: a) How does oxide particle size change with depth of penetration of the oxide? How does this vary with the specific type of solute element? b) What is the effect of solute content on the average oxide particle size?

Jan 1, 1962

By Frederick Laist

(Butte Meeting, August; 1913.) WHILE remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the -treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was, decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the MacDougall type, specially adapted to the work of roasting for leaching; two leaching tanks, 32 ft. in diameter by 12 ft. deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation; for example, by electrolysis and by hydrogen sulphide.

Jan 7, 1913

By Oscar A. Glaeser

The purpose of this paper is to present specific applications of the fundamental principles of mine ventilation and the means that are at our disposal to accomplish the task of maintaining a healthful atmosphere in small mines and prospect openings. Need for Ventilation The range between the maximum oxygen content of normal air and the minimum safe content is extremely narrow, approximately 5 per cent. Furthermore, normal air must not be contaminated with irrespirable gases beyond definite limits, and mineral dusts are equally dangerous, although health impairment is slower. Tables 1 and 2 present the more common respiratory hazards encountered in mines. Adequate ventilation is the most effective means available to reduce or eliminate these hazards. Mechanical ventilation has reached varying stages of perfection in coal mines and in many large metal mines. The small mines and prospects rarely have a definite plan of ventilation. As a consequence underground workers are frequently exposed to health and accident hazards. The annual reports of fatalities in mines in the Western States record yearly many deaths due to asphyxiation and deaths caused by men falling down shafts and raises after being overcome by gas. At times mining operations are slowed up because there is no means of driving out the gas after blasting. For that reason only one shift is worked, or men wait from one to several hours for the "smoke" to clear out. Methane gas in varying quantities is widely distributed throughout California. It has been encountered in explosive concentrations in the coast range. It has been found on the Mother Lode and in quicksilver mines near the coast. Methane explosions have not been uncommon in underground operations and in tunneling jobs. These conditions and records indicate that there is room for improvement in mine-air conditions.

Jan 1, 1937

By Carl R. Davis, J. L. Willey, S. E. T. Ewing

The first tube-mill on the Rand was put into operation in May. 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell, 22 ft. 0 in.; diameter, 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.' By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a ha1 product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; — 90 mesh, 69 per cent.; and the slime grading +200 mesh, 2 per cent.; —200 mesh, 98 per cent. It was recognized comparatively early that the tonnage of — 90-mesh product produced by a tube-mill per 24 hr. was a convenient measure of

Jan 1, 1925

By Philip W. Simmons

THE Colorado Plateau uranium province is in a mining boom rivaling the most colorful days of the early West. The application of scientific skills and the use of modern and novel mechanical equipment, however, is unique. No metal has ever received such concentrated effort from geologists and mining engineers. Moreover, no other metal has had the variety of tools available for finding and mining ores. Radiation detection equipment, bull- dozers, truck-mounted wagon and core drills, jeeps, airplanes, helicopters, tractor loaders, self -propelled 3-wheeled dump cars, front-end loaders and fleets of modern trucks are some of the present-day tools of the uranium prospector and miner. Because uranium is so vital to our national defense, the Atomic Energy Commission has offered many incentives for its mining. Through a series of circulars, the AEC has established base price schedules and various incentive payments. The incentive payments for acceptable ores from domestic mines are: (1) a guaranteed base price of $3.50 per Ib for ores assaying 0.20 pct U3O8 and more; (2) premiums based on grades above 0.20 pct U3O8 as for example, ores assaying above 0.50 pct U3O8 receive $1.00 per lb premium; (3) a development allowance of 506 per Ib of U3O8 contained in ores assaying over 0.10 pct U3O8 (4) an ore haulage allowance of 64 a ton mile for a maximum of 100 miles; and (5) an initial production bonus which may amount to as much as $35,000 in addition to all other payments. The producers have been guaranteed this policy until Feb. 28, 1957. The other four will continue until April 1962.

Jan 4, 1954

By Charles W. Bauer

Most of the aluminum produced in the United States today is derived from foreign bauxite deposits. Earth Sciences, Inc. initiated a program to evaluate domestic non bauxite sources for alumina in the 1960's. In the initial evaluation of alunite, domestic resources were not sufficient to support development. An exploration program led to the discovery of large deposits of alunite in Utah and several other western states. Identification of alunite is difficult as both its physical and chemical characteristics are similar to the minerals with which it is associated. Most of the significant alunite deposits in the western United States are replacement type deposits. These deposits have formed as a result of hydrothermal alteration of volcanic, sub-volcanic, and igneous rocks. Typical alunite deposits contain between 30 and 50% alunite and 50 and 70% quartz, with minor amounts of other minerals. Four mineralogical zones are common in these systems. They include a siliceous zone, a quartz-alunite zone, a kaolinite zone, and a chlorite-montmorillonite zone. Total US reserves of alunite were estimated at 20 Mt fat 30% alunite) by the US Bureau of Mines in 1941. More recent work by the US Geological Survey estimates reserves of 252 Mt and potential resources at 1.4 Gt. Reserves and resources estimated for 23 properties on which field work has been done by ESI are considerably higher. Most of these properties have reserves and potential resources of several hundred million metric tons. The combined demonstrated reserves of these properties are estimated to be about 650 Mt. Inferred reserves are estimated at 2.5 Gt and potential resources at 8 Gt. It appears that the US has sufficient reserves and resources for alunite to be considered as a potential nonbauxite source of alumina.

Jan 1, 1982

By Gerhard Derge

THE introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be described. For most of the additions, solutions containing 0.001 and 0.01 .moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-bonate as follows: pH 0.1 M NaHCO3 8.4 2 parts 0.1 M NaHCO3, 1 part 0.1 M Na2CO3 9.5 1 part 0.1 M NaHCO3, 2 parts 0.1 M Na2CO3 10.0 0.1 M Na2CO3 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves-sulphate, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only-fluoride, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also-phosphate, perborate, and chromate.

Jan 1, 1939

By William C. Brice

Minnesota is involved in planning controversies related to taconite and potential copper-nickel mining. Mine facility planning includes the Reserve dining on-land tailings disposal issue and the potential for a new copper-nickel mining district. Both provide a unique opportunity for innovative planning in the attempt to be responsive to public and private interests. Concerns that emanate as a result of mineral resource activities include environmental protection, land use competition, land exchanges, highway and utility extensions, and legal constraints on public or private lands. The purpose of this newly-developed planning approach is to anticipate such issues and provide a rational information base for dealing with them. The result will be a framework plan for guiding public planning, and an impact assessment for reviewing the implications of industrial project proposals. The approach uses a computer-stored resource inventory of natural and cultural information. Geographic data is mapped and entered into a computer storage and retrieval system. This enables systematic analysis of mineral resources along with environmental and land use considerations. Computer mapping describes the relationship of each activity and allows identification of potential conflicts; it also shows geographical extent in the form of statistical compilations. Resource data is being collected and compiled using a standard metric grid (Universal Transverse Mercator). Individual cells are 100 m. squares and represent areas of about 2.5 acres. The study area contains about 145,000 cells. Data inventories are being compiled in 25 natural and cultural resource categories. Geologic variables include Bedrock Geology, Taconite Reserves and Potential Resources, Depth to the Duluth Complex Contact and two soil inventories. Topographic and hydrologic variables include elevation, slope, slope orientation, surface hydrology, and watersheds. There are also 6 biological data variables and 7 land use inventories.

Jan 1, 1977

By J. J. Gilman

WHEN a cleavage crack that is moving through a crystal intersects a screw dislocation, a jog is created in the crack front. As the crack continues to move, the jog leaves behind a cleavage step. This mechanism was proposed by Amelinckx and Votava,' Pratt, bnd Gilmanh t about the same time. At that time the evidence for the mechanism was largely indirect. Other evidence has been presented by Low, Bilby and Smith,5 and Forty.' It is the purpose of this paper to present more direct evidence of this mechanism and to show that observations of cleavage steps can be used to detect screw dislocations. Experimental Lithium-fluoride crystals that were purchased from the Harshaw Chemical Company, as well as natural mineral crystals and metal crystals, were used in the experiments. Although cleavage steps can be observed on transparent crystals with a metallurgical microscope, the contrast is poor. Marked improvement in the contrast is obtained by depositing thin (1000A) films of silver or aluminum onto the surfaces. The contrast also can be improved by using a phase-contrast microscope, but the simpler silvering method gives just as good results. Tolansky interferometric microscopy, and electron microscopy were used to measure the heights of cleavage steps. The etching techniques developed by Gilman and Johnstonh ere used to detect dislocations in the LiF crystals. Results The dislocations that create cleavage steps can originate in three ways: a) They can be grown into crystals b) They can be introduced by plastic deformation prior to cleavage c) They can be formed just in front of the tip of a propagating cleavage crack.' These three situations will be considered in turn. Grown-in Dislocations—It is not possible to see the individual monomolecular cleavage steps that emanate from isolated screw dislocations in crystals.

Jan 1, 1959

By James W. Burns

Thin, heavily doped n-type layers of GaSb have been grown on p-type GaSb substrates. Techniques have been developed for the growth of the n-type layers from a tellurium-doped gallium-rich solution. The solution used consists of 95 at. pct Ga and 5 at. pct Sb. The process consists of immersing the p-type wafer in the solution at a temperature slightly above the liquidus temperature, holding briefly to permit dissolution of the substrate surface, then decreasing the temperature to a value slightly below the liquidus to obtain 1 HE resistivity of n-type GaSb varies linearly with applied hydrostatic pressure, while the resistivity of p-type GaSb is insensitive to such pressure.1,2 The growth. Growth from a solution of GaSb in tin will also be described. In either case the substrate is clamped to a shelf at one end of a graphite boat, and immersion of the wafer and subsequent decanting of the solution is accomplished simply by tilting the furnace. The process is useful for the formation of p-n junctions in III-V compounds and has the advantage that the problems normally associated with diffusion of Group VI elements are not present. Layers up to 4.0 mils in thickness have been grown by the process. material therefore should be useful in a hydrostatic pressure-sensing device. A practical hydrostatic pressure sensor, however, requires the fabrication of GaSb sensing elements of several hundred ohms resistance. Attempts were made to prepare such elements by diffusion, taking advantage of the high sheet resistance of the thin diffused layers and depending upon the p-n junction to provide isolation from the base layer. Additionally, thin layers of conductivity type opposite from that of the base layer were pre-

Jan 1, 1969

By J. L. Jones

1. Brinell tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin. BRinell Habdness of Babbitt at Increasing Temperatures Bearings fail because of wiping, or deformation. Hence tenacity is desirable in a bearing metal, especially tenacity at high temperatures. The Brinell test is commonly regarded as a measure of tenacity. In fact, it has recently been proposed to substitute for Brinell hardness number the expression " tenacity number."l It seemed, therefore, that the Brinell test was especially adapted for the tests described. Disks, 4 in. (101 mm.) in diameter and 1.5 in. (38 mm.) thick, were made of the babbitts to be studied, designated A, B, C. They were poured into metal molds, pyrometer leads being soldered in the center of each disk. The composition of the babbitts was as follows:

Jan 1, 1919

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

An "international gold conference" was held at Spokane, Wash., on Sept. 5, 1918, under the auspices of the Northwest Mining Association, which was attended by a large number of engineers, mine operators, and bankers, representing the northwestern states, as well as Alaska and British Columbia. The principal subject under consideration was the doleful condition of the gold-mining industry, gripped between the diminished purchasing value of its product, and the increased cost of its operation. Two resolutions were adopted by the meeting. The first approved the resolution adopted Aug. 12 by the American Gold Conference, a permanent organization formed at Reno, Nev., in which it is stated that relief by the United States to the gold producers of this country should he made to correspond with the increased cost of production, the extent of the relief to be fixed from time to time to Meet changing conditions. The second resolution, adopted after serious and long-continued discussion, was introduced by F. A. Ross, mining engineer, of Spokane, and a member of the Institute, and was as follows: WHEREAS, it is now clearly understood and agreed by the allied nations that national gold reserves must be augmented without delay if rapidly expanding credits are to be secured; and WHEREAS, at this time, the production of gold is daily decreasing to an alarming extent because of well known conditions that, render the mining of gold-bearing ores unprofitable; and WHEREAS there is no way by which the mining of gold-bearing ores may be made profitable except by the direct' aid and influence of the government; and WHEREAS the government has appealed to the mining industry for practical information and practicable suggestions upon this subject; therefore, be it

Jan 10, 1918