Search Documents

By D. Hartley

United States Steel Corp's. Minntac mine is located at Mt. Iron, Minn. on the Mesabi Iron range. The taconite pit is two miles wide, with a maximum depth of 170 ft. Millions of tons of crude ore, waste rock, and surface overburden are handled annually at the mine. All crude ore plus some of the lower-grade rock are rail-hauled; other materials are trucked. Length of rail haul averages 3.5 mi, with a lift of 140 ft. The maximum grade against the load is 1 ½ %. Nine 1200 hp diesel-electric locomotives handle trains of 40-and 50-cu yd side dump cars in crude ore and lower-grade rock service. In addition to this continuous operation, locomotives handle coarse tailings disposal and switching duties on an intermittent basis. All railroad equipment operates under the supervision of a mine control foreman through voice radio communication. The pit foreman also has this frequency available, quickly accommodating any changes in operation that may be required.

Jan 1, 1970

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By T. D. Yensen, N. A. Ziegler

The elements aluminum,' arsenic,2 silicon,3 tin2 and vanadium,~.~ when used in relatively small amounts as alloying elements, seem to have a beneficial effect on the magnetic properties of iron—i. e., they increase the maximum permeability and decrease the coercive force—whereas there are definite indications that boron,5 carbon,6 nitrogen: oxygen," phosphorus16 sulfur6 and titaninum,~ as well as the metals of and adjacent to the ferromagnetic group, nickel,~ cobalt,1° copper," and manganese,% have a detrimental effect on these properties. The effects of calcium4 and magnesium4 are small, if any, while the effect of chromium12 in small amounts is unknown and in large amounts is generally detrimental. WeveR's Classification13 All chemical elements may be divided into three classes based on their effect on the allotropic transformation points of iron. Class 1 contains the nonmetallic elements (except phosphorus) and these lower the A3 point and raise the A4 point. Class 2 contains the common metals and

Jan 1, 1931

By J. F. Shirley, H. K. Burke

In January, 1964, three years of laboratory and pilot plant test work reached its culmination. The San Manuel Div. of the Magma Copper Co. switched its molybdenite extraction circuit from the sodium hypochlorite-ferrocyanide process to the new process described in this paper. The San Manuel Div. Concentrator of the Magma Copper Co. is located near San Manuel, Ariz., approximately 45 miles northeast of Tucson. The concentrator treats approximately 35,000 tons of ore per day containing about 0.85% copper and 0.025% molybdenite. The San Manuel ore body is a disseminated copper deposit in quartz monzonite and quartz monzonite porphyry. The primary copper mineral is chalcopyrite; minor amounts of chalcocite, bornite and covellite are also present in varying degrees. Pyrite makes up somewhat more than half the sulfide content of the rock. The molybdenite is nearly always found on fracture faces or associated with quartz veinlets.' On January 9, 1964, the sodium hypochlorite-ferrocyanide process that had been used for molybdenite recovery was replaced by the following process: 1) A conditioning step with hydrogen peroxide, sulfuric acid, sodium cyanide and zinc sulfate. 2) A two stage rougher flotation step with stove oil and sodium ferrocyanide. 3) One cleaning step with sodium ferrocyanide. 4) One cleaning step with sodium hypochlorite and potassium ferricyanide. 5) Four cleaning steps with an anti-foam Exfoam 636 and potassium ferricyanide. COPPER CONCENTRATOR Since molybdenite recovery is closely allied with previous steps in the operation, the copper concentrator will be briefly described first. The ore is ground to approximately 5% plus 65-mesh and 65% minus 200-mesh in a two-step grinding circuit consisting of rod mills in open circuit and ball mills in closed circuit with rake classifiers. A straight forward rougher circuit producing only one concentrate is used. The rougher concentrate is combined with the discharge from the regrind ball mills and is then cycloned, with the overflow going directly to the cleaner circuit and the underflow going to the regrind mills. The feed to the cleaner circuit is approximately 90% to 94% minus 325 mesh. The cleaner circuit consists of two stages in which the tailing from the final cleaner stage is returned to the primary cleaner and the primary cleaner tailing is returned to the rod mill discharge at the head of the circuit. Approximately 0.013 lb of the allyl ester of amyl xanthate (S-3302) per ton of ore is added to the rod mills and approximately 0.006 lb of sodium isopropyl xanthate (2-11) per ton of ore is stage added down the rougher banks. The frother used is methyl iso-butyl carbinol (MIBC) and it is added at various points in the grinding and the rougher flotation circuits. Lime is added to the ball mills and/or to the rod mills to maintain the desired pH in the rougher flotation. The rougher flotation has been operated at various pH levels between 10.5 and 11.5. Fuel oil is added in the regrind mills at a loading of approximately 0.01 lb per ton of ore. Factors Which Directly Affect Molybdenite Recovery: It has been found at San Manuel that, to obtain maximum molybdenite recovery, an oily type flotation collector must be added in the grinding circuit. When molybdenite is crystallized in the characteristic platy form, which appears to be the case almost all of the time at San Manuel, its surface has a greater tendency to adhere to oils than water. 2 Of the several oily type collectors available on the market, the allyl ester of amyl xanthate seems to be the best molybdenite promoter. The floatability of San Manuel's molybdenite does not appear to be affected, at least up to a pH of 11.5, by lime. It has been reported that at several plant operations high lime alkaline circuits have adversely affected the molybdenite recovery.3,4 It has been found through microscopic studies that the bulk of the chalcopyrite will float before the molybdenite in both the rougher and cleaner circuits. It is necessary to add fuel oil to the regrind mills to enhance the

Jan 1, 1965

By S. F. Turcotte, B. J. Grierson

At the Q. I. T. ilmenite smelter, nine electric furnaces produce titania slag and iron At high power levels, a furnace requires either a slag or an iron tap approximately once an hour, using rail cars as slag receptacles and ladles for iron. The correct scheduling of taps is an important operational tool due to peak power load and operational considerations. Over recent years, large increases in furnace capacity have imposed severe strains on the product handling facilities. This situation results in loss of production when several taps are bunched, because of an in- ability to handle many taps simultaneously. An on-line computer program has been developed to generate schedules for tapping a single furnace. By improved scheduling, this program can en- large the tonnage of each tap and minimize the number of taps, while reducing traffic congestion and unit cost s. Future plans call for extension of this technique to all nine furnaces with addition of a master scheduling program to optimize the overall traffic flow in the smelter aisle.

Jan 1, 1969

By R. M. Hudson, P. E. Perry

Weight-gain data obtained by nitriding low-carbon sheet steel in an amrnonia CNH,) atmosphere indicated that the process obeyed a parabolic rate law. The calculated actization energy for nitriding in the range 964" to 1268°F agreed reasonably well with published data. At 1358"F, rate data indicated that the activation energy decreased. Weight-gain data obtained by uszng mixtures of NH3 -Nz at 1268°F containzng jrom 10 to 100 zol pct NH3 also obeyed a parabolic rate law. The rate of 'nitriding increased with an increase in the NH3 content of the gas Mixture. It is well-known that steel heated in gas mixtures containing ammonia (NH3) takes up much larger quantities of nitrogen than steel heated in nitrogen, both gases having a total pressure of 1 atm;' this phenomenon can presumably be attributed to the catalytic decomposition of NH3 on the steel surface to furnish nascent (monatomic) nitrogen. This process was studied bv Brunauer. Jefferson, Emmett, and Hend-ricks at furnace temperatures of 752" and 831°F2 using mixtures of NH3 in Hz. Englehardt and wagner3 reported that, at a furnace temperature of 914°F and under their experimental conditions, both nitriding and denitriding were controlled by the rate of gas-metal reactions at a steel surface rather than by the rate of diffusion of nitrogen in iron. The present study was undertaken to obtain information on the kinetics of nitriding low-carbon steel strip at higher temperatures so that practical rates for short-time strip-annealing treatments could be estimated. Variables studied included time: temperature, and NH, content in the annealing atmosphere. Mechanical and chemical characteristics of steel nitrided in this manner will not be considered in the present article. MATERIALS AND EXPERIMENTAL WORK The samples used were from a commercial low-carbon steel, 0.0244 cm thick, in the cold-reduced condition. The chemical composition of this steel is given in Table I. Panels were cut to 5.1 by 17.8 cm, degreased in toluene, and weighed just before treatment. Four specimens were nitrided under each of the experimental conditions. A study was made of the nitriding rate of steel in a 100 vol pct ammonia atmosphere, 740 mm pressure, at five specific temperatures within the range 964" to 1358°F. The nitriding rates of steel in ammonia-nitrogen gas mixtures containing 10, 18, 26, 50, and 100 vol pct ammonia, 740 mm total pressure, at 1268°F were also determined. All atmospheres used were dried by successively passing them through drying towers packed with soda lime and with Linde Molecular sieve Type 4A. Quoted gas compositions refer to those entering the furnace. Specimens were held in the constant-temperature zone of a vertical annealing tube furnace for times of 14, 3, 5, 10, or 15 min. Gas flow rates were maintained at 3.8 cu ft per hr, which was nineteen volume changes per hour for the system used. The rate of flow was selected to provide a high level of free NH3 for cracking on the steel surface where the ammonia gas is most effectively used as a nitriding agent. The vertical annealing tube furnace consisted of a Hevi-Duty tube furnace with a 2 1/2-in.-ID mullite ceramic high-temperature tube. The constant-temperature zone (controlled within 10°F) was about 10 in. long. After each specimen was degreased, a hole was punched in one end, for attaching the specimen by hook to a chain so that it could be lowered into or raised from the high-temperature portion of the tube by means of a power-driven winch. A stainless-steel access port with O-ring seals was connected by suitable glass-to-metal seals to the cool upper portion of the furnace tube. After the weighed specimen was placed in the access port, the furnace tube was evacuated to approximately 10"3 torr, and then the system was flushed thoroughly with the atmosphere under study. When the gas flow rate and constant-temperature zone of the furnace were established, the specimen was lowered into the constant-temperature zone. The atmosphere flowed from the top to the bottom of the vertical furnace tube and was then vented. For all these runs, during the first 3 min of the time the specimen was in the constant-temperature zone of the furnace the specimen was heating up to the tempera-

Jan 1, 1970

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick's law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring's rate theory equation and Sheibel's correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique' with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By James R. Holden, Frederick E. Wang

Through both single-crystal and powder X-ray diffraction methods, ten A6B23-type compounds have been confirmed to exist between lanthanides (A) (plus scandium and yttrium) and manganese (B); A = Y, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm, and Lu. The formation of a compound of this type is shown to he extremely atomic size-sensitive; hence it can be classified as a "size-factorH compound. The "enveloping effect", a geometrical consideration observed in its crystal structure, is proposed as the reason for the A6B23-type compound being size-sensitive. The approximate ideal geometrical ratio of the radii R/r is 1.31 while experimentally A6B23-type compounds have a radius ratio lying within the range 1.2 to 1.4. FLORIO t al.' characterized the structure of Th6MnZ3 as fcc, space group Fm3m, with 116 atoms in the unit cell. Since then, a number of isotypic binary compounds, and recently Gd n,,' have been confirmed to exist. The fact that strontium and barium form A6Bz3-type compounds with magnesium strongly suggested the possible existence of Ba6Liz3. However, investigation3 showed the compound Ba6LiZ3 to be absent. Since both strontium and barium are group 11-a elements and are therefore "open metals",6 the nonexistence of Ba6LiZ3 can hardly be explained satisfactorily by valence-electron considerations. On the other hand, the consistent atomic-radius ratio, (R/r),* observed for the known A6Bz3-type compounds,3 strongly suggests that the formation of compounds of this type is atomic size-sensitive. Therefore, one is tempted to explain the nonexistence of Ba6LiZ3 entirely on the basis of the atomic-size difference between strontium and barium. However, this approach is not entirely without objection. Atoms are not rigid spheres and are known to vary in size within certain limits.7 Since the atomic-radius difference between strontium and barium (0.07 to 0.09A) is within these limits, it is reasonable to assume that the size difference would have a negligible effect on the formation of Ba6LiZ3. This view is further supported by the fact that the radius ratio, R/r, in other known "size-factor" compounds is observed to range widely—for example, from 1.08 to 1.45 for ABz-type compounds (C15, MgCuz type)' and from 1.37 to 1.58 for AB5-type compounds (D2d, CaZn5 type).g The present investigation was undertaken in order to find a more satisfactory explanation for the non-existence of Ba6LiZ3 and, consequently, a better understanding of the nature of the A6Bz3-type compound. The primary objectives are to confirm the previous conclusion3 that the A6B23-type compound is indeed a "size-factor" compound and subsequently to determine the atomic-radius ratio range in which the A6Bz3-type compound can exist. In order to achieve these objectives, stoichiometric A6Bz3 alloys, where manganese (B) was alloyed with various lanthanide elements (A), were selected for investigation. The atomic-radius ratios of lanthanide elements with manganese range from 1.26 for Lu/~n to 1.46 for Eu/Mn. This radius ratio range includes and exceeds the range of all previously reported A6Bz3-type compounds—1.32 for Th/Mn' through 1.38 for Sr/Li. Furthermore, the atomic-size difference between successive elements of the lanthanide series in order of atomic number) is of the order of 0.01A (europium and ytterbium are exceptions). The series of lanthanon-manganese alloy systems is ideally suited to a precise determination of the limits of allowable atomic-radius ratio for A6Bz3-type compound formation. EXPERIMENTAL PROCEDURE The lanthanide metals, in ingot form, supplied by Michigan Chemical Corp. (St. Louis, Mich.) and Nuclear Corp. of America (Burbank, Calif.), were guaranteed by the suppliers to be at least 99.9 wt pct pure (traces of silicon, calcium, and other minor constituents present on occasion, not to be more than 0.05 wt pct) as shown by spectrographic analysis. Manganese metal, in polycrystalline form, was redistilled from the commercial, chemically pure grade and was analyzed to be at least 99.95 wt pct pure. In all cases, the atom ratio between the two elements in each charge was A (rare-earth meta1):B (manganese) = 6:23 and a constant weight, 3 g, of

Jan 1, 1965

By H. M. Chance

Jan 1, 1887

By Frederick G. Tickell

Petroleum engineers are displaying considerable interest in those fundamental properties of matter and energy that control the phenomena of oil and gas production. The subject is a difficult one to investigate by laboratory experiments for two reasons: (1) it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist in the underground reservoir; (2) if we attempt to scale down the dimensions we are unable to reduce all proportionally. It is as if we tried to construct a model blast furnace for the reduction of iron ore, and reduced all lineal dimensions. We should find that the interstices between the miniature chunks of ore would not permit rapid transfer of gases, that combustion and heat transfer would not take place as in the full size furnace and that, in short, the contraption would not work. Just so, when we attempt to make a reduced scale oil field we find we must have, not only miniature reservoir and miniature wells, but "miniature" sand, 011, gas, etc. Much valuable work, however, has been done along these experimental lines and more will no doubt follow, but investigators should bear this point in mind and strive to attain dimensional homogeneity and dynamical similarity in order that their conclusions may be translated into terms applying to the oil reservoir. As Gibson says,' "These conditions are attained when all terms of the physical equation have the same dimensions, . . . when all corresponding particles of the two systems trace out similar paths and when the velocities are such as to make all corresponding forces acting on two such particles in the same ratio." It is the purpose of this paper to discuss the mechanics of fluid movement as it pertains to the oil pool and to point out the complexity of the laws of fluid delivery under the conditions often found. We have to do, fundamentally, with confined fluids, possessing potential energy whose expenditure is restricted by certain properties of the confining media and of the fluids themselves. The equation of motion and time is completely stated when we can assign values to the propulsive

Jan 1, 1929

By AIME AIME

WEST TEXAS, New Mexico and Northern Mexico form one of the most interesting regions in America for geologists and mining men and are full of points of historical and human interest for others. Including as the region does, a representative portion of the high plateau of Mexico, the front range of the Rocky Mountains and the great down-dropping plains of Texas, there is variety as well as interest in the geological and mining problems there to be studied. Gold and silver mining were the pioneer industries and are yet of high rank in importance. Among the papers to be presented at the El Paso meeting of the Institute this month will be two dealing with silver mining and ore treatment at the Shafter mine in Texas, that most un- usual property which has for so many years been the largest mining enterprise in its region. West Texas is now better known for its petroleum and gas, and in another paper will be described the problems involved in uding natural gas for smelting at the well-known El Paso smelter of the American Smelting and Refining Co. In still other papers, presented at the session sponsored by the West Texas Geological Society and cooperating organizations, the general geology of the region, the potash and the sulfur deposits will be de- scribed. At El Paso the refineries of the great com- panics will be available for visits.

Jan 1, 1930

By A. H. Daane, J. F. Haefling

The limits of miscibility in some of the uranium rare-earth alloy systems have been determined in the temperature range 1000°to 1250°C. The solubilities of lanthanum and cerium in uranium are greater than those of the remaining rare earths by a factor of more than two. The solubility of uranium is greater in cerium, braseodymium, and neodymium than in the other rare-earth metals studied. The values found in this study are in qualitative agreement with those which might be expected if the solubility rules of Hildebrand and Scott are applicable. AS interest in nuclear reactors intensifies, many new types of fuels are being suggested in attempts to improve the economics of some of the proposed reactor schemes. To remove some of the difficulties inherent in the use of solid-fuel elements and their reprocessing, many types of liquid-metal reactors have been suggested. One of the more attractive features of several of these reactor concepts is that they include a continuous or semicontinuous process for the extraction of fission products and "bred" fissionable materials from the fuel, utilizing immiscible metal extractants. This would enable a much higher burn-up of fissionable material to be achieved and would present a very attractive economic picture. Several studies have been reported on equilibrium systems in which there exists a high degree of immiscibility between uranium and another metal that might be used as an extractant in such a processing scheme.' Two of these systems in which a high degree of immiscibility exists are those of uranium with the two rare-earth metals, lanthanum, and cerium. Since the rare earths constitute a significant fraction of the fission products, their removal is of prime importance. It is reasonable to believe that this might be accomplished by equilibrating a rare-earth phase with the contaminated uranium fuel in the liquid state. In order to make a more complete study of those systems which would be of interest either as extractants in a liquid-liquid extraction process, or as fission products formed in the fuel, the alloy systems of uranium with lanthanum, cerium, praseodymium, neodymium, and samarium were studied in some detail in the temperature range 1000" to 1250°C; less detailed studies were made with the other rare earths. In addition to being of value to the reactor program, the data obtained in this study should be of help in making a study of the role played by the electronic structures of metals in determining the nature of metallic solutions. The unique electronic structures of the rare-earth elements make them particularly interesting in this respect. EXPERIMENTAL The usual procedure for a solubility determination was to seal equal volumes of uranium and the particular rare earth in a tantalum crucible under an atmosphere of helium; this crucible was then sealed in a stainless steel jacket in an atmosphere of helium. These samples were equilibrated by repeated inverting of the crucibles in a furnace for 15 min at the desired temperature, left in an upright position for 15 min to permit separation of the two phases, and then quenched under a stream of water. In some runs the temperature of the furnace was held 50' to 100°C above the desired quenching temperature while inverting in order to insure good mixing. However, it was found that above 1200°C the crucibles were subject to failure and for these runs the furnace temperature was not raised above the desired quenching temperature. A small amount of tantalum was dissolved in the uranium and the rare earths in these runs, a maximum of 3 wt pct in the uranium phase at 1250°C and up to 1 wt pct in the rare-earth phase at this temperature. On cooling, the major portion of this tantalum precipitated as primary tantalum crystals. Any residual tantalum would probably have a negligible effect on the mutual solubility of uranium and the rare earths in each other. Samples for analysis were cut from each phase with an abrasive cutting wheel; the region near the interface between the two metals was carefully avoided. In the case of the rare earths with melting points above 1250°C no solubility data were taken on the rare-earth phase since this phase could not have achieved equilibrium in a reasonable length of time. (For the same reason no data were taken on the uranium phase below its melting point of 1132°C.) Equilibrium appeared to have been reached in the uranium phase in these cases although the rare-earth phase had not melted. To verify this, samples were melted together in an arc furnace similar to that described by Kroll.2 These samples were sub-

Jan 1, 1960

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921

By Francois Clerf

IRON ORE fields are situated in both the East and West of France (see maps). The eastern deposit is by far the most important from a tonnage point of view, not only in France, but in all Europe. The ores of this region are known as minette, and are situated in the Lorraine ore fields and the Briey plateau. The iron ores of the West are those of Normandy, Anjou and Brittany. Before the war, a large number of important German companies had acquired considerable interests in these western fields and a heavy trade with Westphalia had begun. Recently, however, conditions have changed and some of the mines of Brittany and Anjou are now idle. From a geological point of view, in Anjou and Brittany, a series of synclines extends from the northwest to the southeast, containing a number of seams of varying thickness and generally intercalated in Silurian and sometimes in Devonian formations. The ore is generally a hematite or a magnetite. The composition varies from 48 to 52 per cent of iron and from 8 to 12 per cent of silica. Con¬servative estimates indicate a con¬siderable tonnage of workable ores (150,000,000 metric tons).

Jan 1, 1936

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse grained specimens of high purity aluminum in the temperature range 800' to 1150°F, permitted the formulation of a theory explaining the formation of kink bands. The X-ray Laue back-reflection technique was used in conjunction with metallographic studies to determine the crystallographic elements involved in kinking and to measure the rotations of the bands. THAT metals deform by the formation of kink bands was first shown by Orowan1 in 1942. He manually compressed cadmium single-crystal wires, the basal planes of which were parallel to the wire axis and to the direction of compression. He found that kink bands formed quite suddenly. Similar experiments were performed by Hess and Barrett2 on zinc with a hydraulic testing machine to permit slower more careful compression. They observed that kink bands formed progressively with increasing compression. Recently Washburn and Parker3 observed the formation of kink bands in zinc single-crystal specimens during tension creep experiments. Each of these authors observed the formation of kink bands but did not make a complete analyses of the crystallographic relationships. In addition to these studies on hexagonal metals, extensive investigations of kink bands formed during deformation of aluminum in tension at room temperature have been reported. Two types of deformation bands have been observed during the deformation of aluminum at room temperature. These are: 1—kink bands: these exhibit a sharp curvature of the lattice along certain surfaces, and 2—bands formed by secondary slip along certain regions. As has already been shown by Honeycombe,4 it is important to point out the difference characterizing the two types of deformation bands. In the first case. for moderate deformation, only one system of slip planes normally is active; in the second case, however, two slip systems are active in the deformation bands. The latter have a rumpled surface because of the action of the two slip systems. In the present work only the first type of band was studied and to avoid any confusion the term kink band will be used exclusively in the discussion which follows. Honeycombe' observed that very narrow kink bands (width, 0.01 mm) formed along the (110) planes during the deformation of high purity aluminum at room temperature. He observed narrower ones in commercially pure aluminum and found also that their width decreased with decreasing temperatures. Chen and Mathewson5 reported the formation of kink bands during tensile testing of single crystals of high purity aluminum at room temperature and pointed out that some rotation occurred about a [211] direction. The influence of the bending moment on the formation of kink bands was illustrated by the experiments of Rohm and Kochendorferl0 who used a Polanyi apparatus to obtain pure shear during tensile testing of high purity aluminum single crystals. Under such conditions only one slip system was active and no kink bands were observed; consequently, no noticeable asterism was detected after deformation. The influence of the bending moment will be discussed later. Calnan8 gave a detailed account of the work performed on kink bands obtained during deformation of aluminum at room temperature. Because no explanation of the process of kink band formation in creep was given in the previous investigations and because some of the above observations are vital to the following discussion the brief review of the literature has been given. It is proposed in the present work to provide an explanation of kink band formation during creep deformation at elevated temperatures. Results and Discussion Kink bands were observed to form during tensile creep testing of high purity (99.995 pct) aluminum specimens, having a very large grain size, in the temperature range 800" to 1150°F. These observations were made in grains which occupied the whole cross section of the specimen. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled to permit easier metallographic and X-ray observations. The final

Jan 1, 1954

By S. H. Penn

One of the more challenging aspects of the unfolding age of space travel centers about the opportunity for man to use the natural resources of other worlds. The first of the extraterrestrial worlds to be exploited will be the moon. After only a scant few thousand years of scratching the earth's crust, man will embark upon a venture that for centuries has excited the imagination of many (while staggering that of most) and may become a reality within the next decade. There has never been a time when so much money and effort will have been expended to exploit an area about which so little is known. Paradoxically, this effort combines much of the detached objectivity so typical of our analytical time with the proverbial optimism of the indefatigable prospector. As the earliest manned lunar missions will be brief and exploratory in nature, astronauts will not be expected to attempt to exploit any of the possible lunar natural resources. In later missions, with a more extended period of time available for the astronauts to stay on the moon, it may be desirable or even necessary to "live off the land". The resulting exploitation of lunar resources will be intended primarily to reduce the dependence of manned missions upon terrestrial logistic support and to reduce the cost of maintaining lunar bases.

Jan 3, 1966

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,' the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

By Fred C., Bond

DETERMINATIONS of circulating load in a classifier operating in closed circuit with a grinding mill are usually made from screen analyses of the mill feed and classifier products. The percentage remaining on someone selected screen size must be used in the calculation, and, because of the wide variation in average particle size between the mill feed and classifier overflow, an accurate and representative result at the selected mesh is often difficult to obtain. To overcome this difficulty and reduce the time required in making the determination, I have devised a method which uses the liquid-solid relationship in the circuit rather than screen analyses. The quantities required for the calculation include only the usual dilution and feed tonnage measurements, which should be made regularly in the course of ordinary mill operation and, in addition, the amount of new water added to the classifier, or to the head of the mill with the new feed. If measurements are obtained on both of these quantities it is possible to check the calculated circulating load, and to calculate the percentage of moisture in the new feed to the mill; or, if the latter is known, to check the feed tonnage.

Jan 1, 1937

By H. R. Peiffer

Composite alloys of silver and alumina are shown to resist flow above the melting point of the continuous matrix. The ability to resist flow depends on the fineness of the dispersion and the oxygen content of the silver. It is believed that the oxygen influences very strongly the bond between the molten silver and the finely divided alumina. RECENT needs for materials with high strength and creep resistance at high temperatures initiated mechanical property studies on dispersed phase materials to near the melting point of the continuous matrix material. Results' of these investigations have shown that certain of these materials do have promise for high-temperature applications. Experiments performed on composite materials of silver and alumina by the author have resulted in the discovery of an interesting effect above the melting point of the silver. In these materials the silver was continuous and the alumina very finely divided (Linde B). It was observed that these materials exhibited strength and resistance to flow above the melting point of the silver matrix. The purpose of this paper will be to describe these properties. METHOD OF PREPARATION The materials were prepared by mixing the proper amount of Linde B alumina and high-purity silver oxide. The alumina content was varied from 5 to 20 wt pct alumina in silver in 5 pct steps. The materials were mixed by blending the constituents in an ordinary food blendor using ethyl alcohol as a vehicle. Enough alcohol was added to the powders to form a mixture with the consistency of a thin mud. After blending for about | hr the material was dried and the silver oxide reduced by heating to 450 OC. The material was then pressed at 25 tsi into a -in. billets 3 in. long. EXPERIMENTAL PROCEDURE The specimens were horizontally supported at either end by knife edge supports of cold-rolled steel. This holder was then placed in a "globar" furnace and a chromel-alumel thermocouple placed very close to the specimen recorded its temperature to within 10°C. Each specimen was heated rapidly to 900°C initially. The specimens were held at temperature approximately 30 min and then the temperature was raised 50 deg. The procedure was repeated until deformation was noted. Photographs were made of the specimens at various temperatures and increments of time using a Polaroid Land camera. RESULTS Fig. 1 shows the 5 pct by weight "Linde B" alumina and silver material after reaching 980 °C. Failure occurred after 15 min at this temperature. There were two points of failure and silver collected at them. No additional flow of the molten silver was noted at any other place. Fig. 2 shows a 20 pct by weight "Linde B" alumina in silver specimen. After 30 min at 1400°C, bowing of this material was observed. Other concentrations of alumina were added to

Jan 1, 1961