Search Documents

By E. F. Jr. Young, H. E. Steinman, G. C. Smith

Through a progressive laboratory and pilot-plant program Jones & Laughlin Steel Corp has analyzed and corrected mine drainage pollution problems at all of its coal mines. In conducting this program, the company found no "typical" drainage discharge. Each discharge point at each mine was unique, so that varied approaches were needed to eliminate stream pollution. To illustrate the variety of these approaches, the treatment of drainage from foul, discharge points at three mines in Pennsylvania will be considered here. The flows and critical analyses of the drainage sources and treated effluents arc shown in Table I. Hydrated Lime Works at Thompson Borehole The discharge stream from the Thompson bore- hole at the Vesta No. 5 mine flowed into a small branch creek where it created a "yellowboy" deposit and affected aquatic life. Investigation indicated that hydrated lime would neutralize the acid and precipitate ferric iron without aeration. Treatment of the 150.000-gpd flow, however, created about 4000 gpd of wet sludge for which there was no nearby accumulation site. With State approval, this sludge was deposited through an unused borehole into an abandoned section of the Vesta No. 6 mine several miles away.

Jan 1, 1970

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By PALMER H. TYLER

WHEN the Mid-Continent Section of the A. I. M. E. met at the roof garden dining room of the Tulsa Club on Monday evening, May 13, most of the members present came prepared with a credulity-stretching yarn of some sort or other, gathered from actual experience. Perhaps it was not realized at the time that such anecdotes would eventually burst into print, but while the excellent dinner was appeasing the inner man the word was passed around that informality and spontaneity of expression would characterize the meeting, with the result that the shackles of convention were eventually cast aside and the meeting waxed better and better until the hour grew ,late, and the chairman, L. G. E. Bignell, originator of the idea, brought to a close what was agreed to be a profitable and entertaining evening. The ball was started rolling by Paul Ruedemann of the program committee, who offered the following:

Jan 1, 1929

James GayleY, New Pork City (communication to the Secretary*) :—The main thing that is sought after in this matter is that all purcliases shall be made by analysis. This is done already in special lines, as in the manufacture of various grades of steel in which phosphorus, silicon and sulphur are specified within narrow limits, and I quite agree with Mr. Cook that specifications, which are over-rigid in unessential particulars, should be avoided, as they defeat their own purpose because unreasonable requirements permitting no variation are practically not fulfilled, and it is impossible to specify grade

Jan 1, 1905

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By R. E. Allen, A. C. Jephson

ELECTROLYTIC zinc plants of the American Smelting and Refining Co. are located adjacent to the present city limits of Corpus Christi, Texas. The original plant commenced operations during 1942, and is designed for the production of special high grade zinc from zinc sulfide concentrates.' Subsequent changes include the erection of an additional acid plant during 1950, and additions for increased generating and production capacity during 1951. New Electrolytic Plant—The new electrolytic plant is a separate unit erected for the treatment of densified fume produced at Asarco plants located in El Paso, Texas and Chihuahua, Mexico. Construction was completed and operation commenced during June, 1953. Decision for the erection of a separate plant for the treatment of densified fume is based on several factors. One of the principal reasons is the assurance of continued production rate of the original plant, which might have been jeopardized by combined treatment of calcine and fume. Of equal importance is the advantage of locating a plant on a site with adequate space for eventual expansion. General Description—The new plant for the treatment of densified fume consists of four main buildings for the following operations: storage and grinding of fume, leaching and purification, electrolyzing and casting, and rectifier units. Auxiliary buildings include a baghouse, reagent storage, and a lunch room. Leaching of ground fume with electrolyte from the cells is a batch type operation in tanks equipped with mechanical agitators and weightometers. Completed leaches are pressure filtered, the resultant residue being recovered for shipment to El Paso by conventional use of thickeners, drum type vacuum filters, and a direct-fired dryer. Filtrates from the filter section are purified in mechanically agitated tanks, filtered after completion through plate and frame presses, and then pumped to an evaporative type cooling tower. Solution discharged from the basin of the cooling tower is collected in storage tanks for use in the cells. The cool purified solutions are pumped as required from storage to the solution circuit for circulation of electrolyte through the cells. Except for the addition of purified feed solution and withdrawal of electrolyte for leaching, the circulating system for the cells is essentially a closed continuous circuit that includes the use of evaporative cooling towers for control of solution temperatures. Aluminum cathodes and Ag-Pb anodes are used for electrolysis, which is maintained at a current density of about 82 amp per sq ft. Cathode zinc produced is melted in a gas-fired reverberatory furnace and then cast into slabs on a straight line casting machine. Unloading and Storage—Fume produced by the Chihuahua plant is shipped in box cars, and fume by the El Paso plant in hopper bottom dump cars. Shipments as received are weighed on a 7 5-ton capacity railroad scale, sampled, and then moved over one of the two unloading hoppers with a car puller. The cars are then unloaded with mechanized equipment, a car scoop being used for unloading of box cars and a car shaker for the hopper bottom cars

Jan 1, 1958

By Donald N. Rosenblatt

I would like to commend the author on his description of Pinto Valley's plant, and its interesting innovations. The author's discussion of 18 ft in diameter by 21 ft long primary ball mills (the largest wet ball mills made to date) is of considerable importance to those who have been engaged in the field of studying ball mill liner wear as it relates to various grinding installations. While it is stated that the mills have operated on a fixed tonnage and therefore it has been difficult to determine the best liner pattern, calculations from the data in the paper indicates that for mills 1, 2, 5, and 6, the tonnage per hour varies from a low of 223 for mill No. 1, up to a high of 314, for mill No. 2, while mills 5 and 6 calculate 285 and 246, respectively. Analysis of the wear patterns for the single wave liners used in mill No. 1 as compared to the double wave liners in mill No. 2, suggests that the author's data may tell more than he suspects about liner wear to be expected and thus what should be a best pattern selection from what may appear to be only limited hours of operation. [Fig. A] is a reproduction of author's [Fig. 10], to which wear forecast patterns [F-1 and F-2] have been added. Forecasts are based on many previous studies of large diameter ball mill operations over many years of field service. Calculations from the first-wear pattern provide an initial wear rate of only 13 lb of liner per 100 sq ft of shell liner surface per day, or 0.031 lb per to: ground. However, the second wear pattern is ac-

Jan 1, 1978

By Ralph Hultgren

Few phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups lIIa to VIIIa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjewl determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or quptbr-lattice near the composition FePda. Jellinghausz found that annealing at 500" C. greatly increased 111 magnetic coercive force of an alloy of composition FePd. X-ray diffraction photographs showed that a tetragonal ordered phase had formed during the anneal. Hocart and Fallot made magnetic measurements over the entire range of composition. They found that less than 5 atomic per cent Pd

Jan 1, 1939

By Ralph Hultgren

Few phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups lIIa to VIIIa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjewl determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or quptbr-lattice near the composition FePda. Jellinghausz found that annealing at 500" C. greatly increased 111 magnetic coercive force of an alloy of composition FePd. X-ray diffraction photographs showed that a tetragonal ordered phase had formed during the anneal. Hocart and Fallot made magnetic measurements over the entire range of composition. They found that less than 5 atomic per cent Pd

Jan 1, 1939

By E. C. Robertson

Observations of faults in mines, at outcrops, and in the laboratory lead to the conclusion that the displacement d of a fault increases irregularly but monotonically with the thickness t of its associated fault gouge and breccia, not including adjacent undisplaced jointed rock. The general trend of data points has a slope d/t of about 100. (The correlation coefficient of a logarithmic regression line is r = 0.94.) The rather wide scatter of the points can be accounted for by inaccuracies in measurement of d and t, and by variation in the conditions at faulting of confining pressure, rock type, water pressure, and deformation history. Limestone is an exception to the relation. Until the data can be corrected and refined, the relation should be used only qualitatively for estimating displacement of ore bodies in mines. The suggested relation is based on observations of 48 steeply- dipping normal and reverse faults and nine small flat-dipping thrust faults, with displacement less than 5 km (3 miles). It does not apply to large strike-slip and low-angle overthrust faults because their large displacements are poorly determined and their breccia thicknesses are widely variable.

Jan 1, 1984

By C. S. Yust, C. S. Morgan

ThIS note reports the observation of masses of dislocation etch pits around the weld necks of small single-crystal particles of calcium fluoride sintered to a cleaved face of a larger CaFz crystal. Crystal particles in the -50 +I00 mesh size range were placed on freshly cleaved CaFz surfaces and heated at 1250°C for 30 min in a tantalum container in an argon atmosphere. The sintered specimens were then etched at room temperature for 40 to 50 min in a 2 pct sulfamic acid solution which is a selective etch for dislocations in caF2.' Figs. 1 through 3 show the masses of dislocation etch pits observed around weld necks after etching. In some cases, particles were gone after removal of the specimens from the furnace although weld necks were readily visible. In other instances, no etch pits formed around a weld neck. A possible cause of concentrations of dislocations on the crystal surface is mechanical deformation of the base crystal when particles are dropped on it. If such a deformation does occur, it would be much smaller than that caused by the light punching of a crystal with a sharp instrument which results in large concentrations of etch pits. However, crystals deformed by punching with the sharp instrument and annealed at the conditions of these experiments (1250°C for 30 min) before etching showed no concentrations of dislocation etch pits. It is obvious that dislocations from the much smaller deformations, possibly created when particles are placed on the surface, would also anneal out. Etching of large crystals which had particles placed on them in the usual manner but which were not heated showed no dislocation concentrations such as shown in Fig. 1. The magnitude of dislocation etch-pit concentrations did not vary with extensive variation of the cooling rate. The appearance of many of the etch-pit clusters is typical of a well-annealed condition, indicating that the dislocation concentrations formed before the specimen temperature was lowered. Therefore, it is evident that thermal stresses in the neck area did not create the deformation indicated by the presence of the dislocations. The possibility exists that the etch-pit concentrations at places where particles had been removed may be the result of deformation accompanying the fracture of the sintered bond. That this is not so was demonstrated by breaking off particles around which no etch pits occurred. Re-etching never resulted in the large concentrations observed at sintering sites. The stress available to effect material movement during sintering of two particles will depend on the geometry at the contact point but can easily exceed the macroscopic yield stress in CaFz systems. It appears that the plastic deformation observed results from sintering or simply from the weight of the small particles. It has been previously argued that plastic flow makes an important contribution to the initial densification of oxides having the fluorite crystal structure.2p3 If plastic deformation occurs, it would begin as soon as the temperature is sufficiently high

Jan 1, 1967

By K. D. Jacob

IN the decreasing order of the tonnages involved, the uses of phosphates can be grouped conveniently into three general classes, namely, fertilizer; chemicals for military, industrial, and technical purposes; and mineral feed for livestock. The quantity of phosphate used as fertilizer, principally in the form of superphosphate, has always exceeded by far that used for all other purposes, though in recent years a marked increase has occurred in its consumption for the other two general classes of uses. Prior to the present century large quantities of superphosphate, as well as a considerable portion of the production of phosphorus chemicals, score made from bone materials which were plentiful and cheap in some areas and which could be more easily processed than phosphate rock for the manufacture of chemicals. Today, however phosphate rock has almost completely displaced bone as a raw material for the manufacture of chemically processed phosphates in nearly all countries of the world.

Jan 1, 1944

By William B. Plank

RECENT interest in the character of employment of young mining engineering graduates has been stimulated by my studies, during the past ten years, of student enrollment and employment of graduates of the mineral technology schools of the United States and Canada. Enrollment data in the following article are taken from these studies and information about the kind of work engaged in by mining engineers is assembled from my professional experience, sixteen years of which have been as professor of mining engineering.

Jan 1, 1938

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

By AIME AIME

C. H. BENEDICT, chief metallurgist of the Calumet and Hecla Consolidated Copper Co., has pioneered for nearly half a century. Noted for his ammonia leaching process, lie has Iong been responsible for all Calumet and Hecla mill, concentrator, and reclaination plant flowsheets. His influence has spread far beyond his own organization. lie is dean of Lake Superior metallurgists and has contributed greatly toward raising his specialty-the country over-to an honored profession; not merely an honored profession but a profitable one for industry and the public. The leaching process which he developed in 1912 has, since 1915, produced for Calumet and Hecla 250,000 tons of copper from waste tailings at a cost per pound, in 1929, below five cents. It has yielded profits of $35,000,000. In the war just ended, this process proved the only one adaptable to the recovery of copper from gilding-metal¬clad steel strip, and Calumet and Hecla treated more than 50,000 tons of such scrap for the Government.

Jan 1, 1945

By AIME AIME

BLANDFORD. C. BURGESS, the new Chairman of the Industrial Minerals Division, took the advice of Horace Greeley in reverse-he turned his hack on San Francisco and the Golden Gate, and after a few side excursions toward Alaska and Arizona, hit the trail eastward, not for the lonesome pine, but for Spruce Pine, N. C. Born Aug. 10, 1893, in San Francisco. Burgess found his first job, shortly after finishing high school at 19, as axeman for a surveying party of engineers working for the Southern Pacific Co. in Oregon. Later he moved on up with them into Alaska. He liked the engineering profession, and decided to equip himself further so he entered the University of California in the fall of 1913. and for the next two years devoted himself to acquiring an education in civil engineering.

Jan 1, 1945

By B. D. Saklatwalla

FOR the proper understanding of the inclusion of certain elements in this review it seems necessary to state the meaning of "rare metals." Certain elements occur in deposits limited in extent or concentration, so that the extraction of the element in relation to market conditions becomes uneconomical. Others may occur in extensive and rich deposits but the reduction of the metal may be difficult and costly. Both these conditions effect the same result, namely, make the metal rare and costly. As an example of the first kind may be mentioned radium and of the second, calcium.

Jan 1, 1939

By OTTO HERRES

UTAH has enormous deposits of high-grade bituminous coal. The United States Geological Survey estimates that there are 13,130 sq. mi. of land in Utah known to contain workable coal and these extensive fields contain 196,000,000,000 tons of coal. Growth in population and development of industry in the intermountain and Pacific coast regions will in time give Utah a place with the great coal producing states of the country. Even today, faced by adverse conditions in competition with cheap fuel oil from southern California, water-power throughout the western states in general, and comparatively high freight rates to its distant markets, the Utah coal industry is notable in many respects. In recent years, Utah has led the United States both in the percentage of its mines in class 1, mines producing more than 200,000 tons a year, and in average production per man per day, which was 6.01 tons in 1921. In Mineral Resources of the United States, 1921, Part

Jan 1, 1925

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

The following advertisements show the contemporary view of the value of coal on a tract, usually as compared with farming advantages of several kinds. Fayette Gazette and Union Advertiser, February 10, 1798: "For Sale in Washington twp., Fayette Co., 211 acres of land whereon is a good new grist merchant mill, a good stone dam, and a house for the miller, about two acres of bottom, cleared and fenced, an excellent coal bank and saw-mill seat unimproved." Pittsburgh Gazette, March 19 and 26, 1802: Ads. offering for sale two properties, one of 38 acres, "together with a Coal Pitt and Lime Quarry, lying on the Monongahela side of Grant's Hill, and within one mile and a half of Pittsburgh," and the other two tracts of 700 acres on "Racoon creek, contiguous to which is a valuable limestone quarry, and a quarry of building stone, also plenty of stone coal." Pittsburgh Gazette, Oct. 8, 1802: A farm between Pittsburgh and Greensburg "with house, barn and a Smith shop-also, a fine sugar camp, and a Coal Bank within sight of the house," was offered for sale. The Farmers Register, Greensburg, Pa., March 13, 1802: An advertisement of a "plantation, six miles from Greensburg, there are two coal banks on it, one at each end of the place." The Commonwealth, Pittsburgh, Aug. 4,1805: A number of lots were laid off on Saw Mill Run, nearly opposite the first opening made on the Pittsburgh seam. They were from two to twenty acres each "and a great quantity of Limestone and stone coal." Pittsburgh Gazette, Aug. 9, Sept. 6, Sept. 27, Oct. 4, 1811; The Commonwealth, Aug. 19, 1811: Five tracts were advertised that contained coal. One had "fine springs and an inexhaustible mine of coal;" one, "excellent sugar camps, coal banks and limestone and a good mill seat;" one, "good sugar camps, an excellent coal bank and an elegant seat for a distillery;" another, a tract of 45,000 acres in Allegheny and Butler Counties affording "stone coal and iron ore, and seats for water works;" and the last a tract on Beck's Run, four miles from Pittsburgh "and a coal pit opened about one fourth of a mile from the river." The Mercury, Pittsburgh, April 8, Jan. 14, Feb. 11, 1813; Pittsburgh Gazette, April 16, Dec. 3, 1813: These tracts were advertised during the year in the vicinity of the city. One had "a good sugar camp, woodland and plenty of coal;" another, "a sugar camp and a coal bank on the premises;" while the others were "well timbered or well watered and had excellent stone coal." The Mercury, Pittsburgh, Feb. 2, 1814: A farm was offered for sale on the headwaters of Robinson's Run, in Washington County, four miles from Burgettstown, containing 60 acres, "a young bearing orchard,... a coal bank and a good sugar camp." Genius of Liberty and Fayette Advertiser, Uniontown, Pa., March 2, 1814, carried an advertisement of a sale of lots in the new town of Perriopolis; "the quantity and quality of the clay, sand and salt licks, near the premises, together with the timber and abundance of .stone coals The town of Perriopolis was situated upon a . farm at one time belonging to Washington.

Jan 1, 1942