Search Documents

By Donald R. Williamson, Edward R. Mueller

Cyprus Pima Mining Co.'s open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. Over the years, a number of attempts have been made to refine and polish the ore reserve figures using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results.

Jan 1, 1978

By Z. M. Zavodni

The stability of waste dumps depends to a great extent on the physical properties of the underlying foundation. These physical properties are evaluated through surface geotechnical surveys, subsurface exploration, and field and laboratory testing. Sufficient information must be obtained to define and assess the strength, consolidation, distribution, topographic and hydrogeologic properties for these materials. Important foundation data collected in the field include: surface infiltration rates, downhole hydraulic conductivities, ground water levels, bedrock structural parameters, soil types and soil thickness. Laboratory testing should identify the classification, strength, moisture content, hydraulic conductivity, attenuation and consolidation characteristics. Summarized in this paper are procedures and typical results of porphyry copper leach dump foundation investigations. Laboratory properties and design recommendations for potenia1 foundation liner materials are described. Back analysis and laboratory foundation strengths are compared. The topographic effect of the foundation on dump behavior is discussed and a foundation pore pressure monitoring experiment at the toe of an active waste dump is described.

Jan 1, 1985

By A. C. Noble, D. E. Ranta

Orebodies with intricate three- dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer- assisted methods. 'The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral de- posits.

Jan 1, 1984

By J. L. Rodda

A large amount of time has been devoted to the microscopical study of the copper-zinc alloys, emphasis naturally being placed upon the commercially important alloys of the system. Suitable methods are available for microscopically recognizing the two phases richest in copper, but none appear to have been developed for the positive identification of the other phases. This is, however, accomplished, for the phases normally encountered, by an electrolytic method described in the following pages. Five phases of the copper-zinc diagram (Fig. I) are considered for the purpose of this paper: the solid solution of zinc in copper, alpha (a); the intermediate phases, beta (ß), gamma (?), and epsilon (e); and the solid solution of copper in zinc, eta (11). Beta prime is not considered a separate

Jan 1, 1937

In the four articles presented on the following pages, a panel of comminution experts offer readers the benefit of their experience with autogenous grinding and forecast some of the future developments to be expected in this fast-growing field. The articles are based on an AIME panel discussion in which the authors participated.

Jan 1, 1970

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for up- grading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching.

Jan 4, 1953

By H. M. Chance

Stretching from New York southwestwardly to Georgia is a great range of hills and mountains consisting of pre-Palæozoic schists, slates, .and gneissic and granitoid rocks, known locally by many different names; in Pennsylvania as the South mountains, the Berkshire or Durham and Reading hills, and in Virginia and farther south as the Blue ridge. To the northwest of this range lies the " Great Valley," underlain by Lower Silurian limestones, and known as the Lehigh valley, Cumberland valley, Shenandoah valley, valley of Eastern Tennessee and Georgia and by other local names, but all these are parts of one valley, geologically and geographically continuous from New Jersey to Georgia. Lying upon and along the northern flank of this range of mountains, and dipping northwestwardly under the limestone of the valley, is the Potsdam formation (Primal or No. 1 of the Pennsylvania Geological Survey), which consists of sandstone or conglomerate overlain by slates. The latter are sometimes arenaceous and occasionally are replaced in part by sandstone. This formation varies from a few feet to several hundred feet in thickness. At the outcrop the slates are completely decomposed, oxidized or disintegrated, forming a belt of clay several hundred feet wide occupying the interval between the outcroppings of the sandstone and limestone. This clay-belt includes a more or less continuous series of iron-ore (brown hematite) deposite, which have been, and still are, extensively worked. The belt is more or less continuously milleralized with iron throughout its length, and hundreds of large deposits of ore have been developed and worked, producing many millions of tons of ore.

Jan 1, 1909

By H. W. Kropholler, L. A. Cramer, E. T. Woodburn, J. C. A. Greene

A generalized mathematical structure is proposed whereby internal species mass flows within a flotation network are defined uniquely by a matrix of enhancement factors. An element of the enhancement factor matrix is defined as the ratio of the mass flow of that species leaving a given cell in the concentrate to the species mass flow leaving the same cell in the tailings. To predict the enhancement factors, knowledge of flotation kinetics effects is required. Recently experimental data has become available relating to the performance of industrial flotation circuits which indicate that the discrete or discrete-distributed kinetic schemes are capable of reasonably effective simulations. These simulations show the importance of including froth effects. The prediction of performance of networks from small-scale batch tests on flotation streams shows that the model for the froth phase used in the simulations does not scale-up well and that aeration effects are also difficult to predict. The network analysis should be useful in differential flotation of complex ores and it is disappointing-in this context that little information on the kinetics of activation and depression is available.

Jan 1, 1976

By J. Poijärvi, J. Rastas

Recently, when increasing attention has been paid to mercury for environmental reasons, the interest of several plants is directed to the removal of mercury from roaster and smelter gases. When Outokumpu Oy built its zinc plant at Kokkola in 1969, intensive development work was started to find an efficient and economic method for mercury removal from roaster gases. A process was developed, after laboratory research and pilot plant tests, to eliminate and completely recover mercury from the roaster gases. The process was commissioned in 1970. The behaviour of mercury in the roasting process and several possible methods of removing it from gases are discussed in this paper. Theoretical investigations and empirical tests show that the removal of elemental mercury from gases by sulphatization is very efficient. Further, it is stated how the technical process was built on this idea. The zinc sulphide concentrates contain small quantities of selenium, chlorine and fluorine. The role of selenium in the process is described. Similarly, the behaviour of chlorine and fluorine in the roasting, sulphatizing and scrubbing units has been discussed. Finally, the recovery of purified mercury and selenium from the precipitates is described.

Jan 1, 1973

By G. R. St. Pierre, L. M. Adelsberg, R. Speiser

The rate of scale fot'~I~ti0n on tantalum held in H20-Hz-Ar gns mixtures at temperatures between 840" and 1250°C is related to gas composition and ternpevature. It is found that water vapor partial pressure determines the oxidation rate at a given temperature and that the oxygen potential as fixed by the water vapor to hydrogen ratio Ins no significant effect on the oxidation rate. The Ta205 scale formed during oxidation is composed of an inner lattice-dijf~ision barrier and an outer layer of- cracked/porous oxide 1 HE oxidation of tantalum at temperatures less than 800°C is characterized by solution of oxygen into the metal,'-' the formation and growth of suboxides into the metal,')2~10-15 and the delayed nucleation of the highest oxide, Above 800°C, Ta205 is found to nucleate rapidly10, 11, 15, 16 except at low oxygen pressures:15 however, there is uncertainty regarding which does not retard the oxidation process. For each gas con~position and temperature investigated, the oxidatioz rate becomes constant after a short adjustment period. It is shozm that a constant oxidation rate nzay pre~?ail even though the tlzickness of the inner lattice-dijjitsion layer of Ta205 is clanging. TFze initial czcrz!ature of the typical 'Paralinear" oxidation curve may result froprz causes other than an increasing thickness of tlze inner protective layer. the detailed mechanisms of the high-temperature oxidation. Peterson, Fassell, and wadsworth17 observed linear oxidation behavior for tantalum in oxygen at temperatures between 600" and 1000°C. They reported that equilibrium adsorption of 0, occurs on a surface prior to the rate-deter mining step of the reaction. Cowgill and stringer1' confirmed the observations of Peterson and his coworkers. They stated that the rate-determining step of the reaction could be either the incorporation of adsorbed oxygen into the anion lattice or the dissociation of 0, at the gas-oxide interface. The relative rates of the two surface reactions were proposed to be dependent upon the reaction temperature and the oxygen pressure. stringerlo subsequently reported that the reaction surface is located somewhere

Jan 1, 1968

By P. P. Reichert, L. S. Gournay, N. T. Burdine

An investigation of equivalent pore entry radii in typical samples of petroleum reservoir rock and the pore volume associated with each value of pore entry radius has been made. Theoretical discussions together with experimental procedures for obtaining pore entry radii and the distribution of pore volume with pore entry radii are presented. Experimental results on a number of core samples, along with typical distribution curves, are shown. Data on the per cent of the pore volume filled by mercury at a pressure of 1500 psi are included. The results of re-runs of samples, made possible by regenerative apparatus, show the repeatability of the data and indicate the amount of physical change in the samples by mercury penetration. Theoretical equations for calculating permeability from pore size distribution data were derived and the results of such calculations are compared with measured gas permeability data. The effect of the shape, surface area, and weight of the sample on the pore size distribution of reservoir rocks was investigated experimentally. Mercury capillary pressure curves are compared with those obtained by the porous diaphragm method using pas to displace water. Standard core analysis techniques, in general, lead to quantities which are statistical averages of the varying properties of the samples under examination. Although such statistical information has real value in predicting the gross performance of porous bodies. it fails to provide fundamental information concerning the properties of the porous medium itself or any processes which may be occurring in it. For example, a gas permeability measurement on a core sample is an indirect way of determining an average pore radius for that particular sample. Since there are many combinations of pore radii that will give the same radius. and, hence, the same permeability, no information is obtained on the pore size distribution. Furthermore, similar values in permeability do not imply similarity in other properties of a porous medium. For instance, it is possible to have two core samples with identical permeability which would have different residual oil contents at the end of an air-oil drive, or even different amounts of interstitial water. It has been recognized for some time by the petroleum industry that a determination of pore size distribution for porous reservoir rocks offered promise of increased understanding of fundamental flow processes in the porous matrix. and therefore of petroleum res- ervoir performance in general. There have recently been published several methods for determination of pore size distribution in porous materials. A report is given here of the modifications in equipment and technique required to adapt one of these methods to measurements on petroleum reservoir core samples. Although only a few correlations or applications of the method are available for presentation at this time, the technique is brought to the attention of the industry so that the opinions and experience of others with this or similar techniques may be exchanged. It seems possible that the method will have wide application in the future. METHOD There are three general methods which may be employed to measure the pore size distribution in naturally occurring rock formations. One method1 is based on experimentally determined adsorption isotherms for calculating the surface area of the porous medium. Knowing the surface area and the pore volume, a rough estimate of the pore radius can be made. Since this method depends on the thickness and uniformity of the adsorbed layer, the validity of the results would be highly questionable. A second method utilizes capillary pressure data obtained by static dis-

Jan 1, 1950

By Oscar Aguilar, Jin-ichi Nakamura, Kazuo Nakamura

Michiquillay deposit is porphyry copper type with over 500 million tons of 0.70% Cu ore. In order to reflect the true nature of the orebody as to shape and value distribution and to compensate for insufficient data in the outer perimeter and lower portion, "Triangular Interpolation Method" is used in the computation, wherein block grades are determined by "Plane Regression". The results thus obtained are compared with the data from additional investigation and are found to match well with each other. Aside of total Cu, assays of Fe, S, MoS2 and geological data such as alterations, rock types, faults, mineralogical compositions are also stored in the computer. By this system, their distribution and relation to alteration become clear and classification of ore into types affecting recovery become possible. The outputs of this system make clear the characteristics of the orebody and furnish valuable geological data on the orebody.

Jan 1, 1976

By D. G. Russell

A simple method has been developed with which flowing bottom-hole pressure data from two-rate flow tests in oil or gas wells can be analyzed to estimate the formation permeability, skin factor and average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized producing rate of the well is changed to another, higher or lower, rate. The new method yields the same information as a conventional pressure buildup analysis, but eliminates the need for closing in the well. The analysis of a two-rate flow test is of the same degree of difficulty and requires about the same engineering time for application as a conventional pressure buildup analysrs. The extended closed-in periods experienced with conventional buildups because of long, low-rate afterproduc-tion periods are eliminated by fIow tests. Other anomalous pressure buildup effects, such as "humping" due to weli-bore phase segregation, can be successfully eliminated with the new method. Generally, flow tests of about 24 hours' duration run with conventional pressure measurement equipment are sufficient for interpretation purposes. Field testing of the two-rate flow test method has established that it is a reliable and economical method which can be used in many instances to complement or even replace conventional pressure buildup methods. INTRODUCTION The principal method for estimating formation permeability and well damage, or skin factor, in a producing oil or gas well is the analysis of shut-in bottom-hole pressure buildup data.' This familiar method has been used quite successfully by reservoir engineers for many years. It is based on the solution of the radial flow equation for constant rate conditions, and requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed t + ?t bottomhole pressure vs log t + ?/?t(where At is shut-in A? time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the permeability, skin factor, and reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. Over the years several drawbacks have become apparent in the use of conventional shut-in pressure buildups for determining permeability and skin factor. The conventional pressure buildup interpretation theory assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing in to the formation. This adjustment period is commonly referred to as the "after-production" portion of the pressure buildup. In the tight reservoirs, long, low-rate after-production periods frequently occur, and the well must be shut in for several days or, in some instances, even weeks to obtain an interpretable buildup curve.' Obviously, such long shut-in times can cause loss in current income, both from reduced oil production and from the fact that personnel and pressure measurement equipment are occupied with a single well for too long a time. In other cases, even long shut-in periods do not seem to be of much aid in obtaining an interpretable buildup." If there is considerable phase redistribution (liquid fallout or bubble rise) after a well is shut in, then curves with no interpretable portion are often obtained during the buildup. In addition to instances in which wellbore effects cause trouble, there are also cases in which the major objection to use of the closed-in pressure buildup is simply the fact that the well must be shut in. When there is no proration and when the well has limited producing capacity. closing in the well means loss of income. From the foregoing discussion it is apparent that it ib desirable to have an alternative method of obtaining the same information as that derived from a conventional buildup without the need of closing in the well. One possible solution which has been offered for this problem is the use of a bottom-hole shut-in tool' which isolates the major portion of the flow string from the formation face during the buildup. In this paper an alternative method which is frequently successful in avoiding wellbore effects and which does not require the use of special equipment is presented. A new, simple method has been developed with which the flowing bottom-hole pressure data from flow tests in oil or gas wells can be used to estimate permeability, skin factor and the average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized production rate of the well is changed to another, higher or lower rate. The need for closing in the well is eliminated, and pressure measurement periods of only 18 to 24 hours arc usually sufficient, even in tight reservoirs. Thus, the new

By Martin J. Conway

DURING the past year, the intense interest shown by the metallurgical industry in the use of relatively pure oxygen has been evidenced by the number of papers dealing with its application and production. The reason for this interest is apparent when it is realized that, weight for weight, oxygen enters into the formation of steel equally with iron. In the manufacture of steel, approximately one ton of oxygen is required to produce one ton of ingots. Until the recent development of plants capable of producing oxygen at far lower costs than had ever previously been considered possible, the oxygen required for steel manufacture was used as it occurs in air, where it is associated with approximately four times its volume of nitrogen. Because of the diluent nitrogen more than 4 tons of total gaseous material per ton of steel must be handled rather than only approximately one ton required when pure oxygen is used. In addition, provision must be made to handle the large quantity of waste, gases resulting from the process. There are cases where the reduction in gas volume alone can justify the installation of an oxygen plant.

Jan 1, 1947

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985

By W. F. Hosford

A quantitative explanation is offered for the peculiar curled grain shapes found in the microstructures of drawn wires of bcc metals and compressed aluminum specimens. It is shown that once an [011] fiber texture is developed, the slip system are so oriented that further slip tends to produce plane strain rather than axially symmetric flow of individual grains. With plane -strain flow, however, compatibility of neighboring grains can be maintained only by a bending of grains about one another. PROBABLY the most obvious microstructural feature of heavily worked metals is the distorted shapes of grains. In the course of deformation, the shape change of each grain must be compatible with that of neighboring grains; otherwise holes would be formed at grain boundaries. In analyses of poly-crystalline deformation by Taylor and subsequent workers it was assumed that grain boundary compatability was maintained by each grain undergoing the same shape change as the polycrystalline aggregate in which it is imbedded. According to this assumption, when simple tension or compression is applied to a random polycrystal or to one with a fiber texture, each grain ought to deform with axially symmetric flow. Initially equiaxed grains should become cigar-shaped during wire drawing and pancake-shaped during compression. While microstructural observations of deformed metals are generally in accord with such a picture, certain striking exceptions may be noted. Peck and Thomas5'8 found that grains in heavily drawn tungsten, iron, and niobium (columbium) wires become shaped like ribbons curled about the wire axis, Fig. 1. At a suggestion from the author, they rationalized the development of these micro-structures by considering the orientation of the slip systems in the [011] texture formed by the wire drawing. It is shown in this paper that marked departure from axially symmetric flow of grains is also observed when polycrystalline aluminum is severely compressed. Again the explanation must lie in the orientation of the slip system in the [011] texture, which is formed in fcc metals by compression.' THEORY A simple quantitative argument will be presented to show that the development of these microstructures is a result of flow on the combination of slip systems for which the minimum amount of mechanical work is expended in producing a unit tensile (or compressive) strain. First it must be realized that the macroscopic strains of a crystal resulting from slip are given by: where d dy, and dc, are normal strain increments parallel to the x, y, and z reference axes; are crystallographic shear-strain increments on slip systems

Jan 1, 1964

By J. O. Lewis, Carl H. Beal

Introduction ............................... 492 Theories Relating to the Recovery of Oil.................. 493 Methods Commonly Employed for the Estimation of Future Production..... 495 Saturation Method........................... 495 Production Curve Method....................... 496 Production per Acre Method.....................: 496 Appraisal Curves.............................. 498 Derivation and Construction...................... 498 Comparison of Appraisal Curves of the Osage and Nowata Fields...... 505 Use of Appraisal Curves........................ 506 Accuracy of the Apprais?l Curves and Their Sources of Error........ 508 Relation Between Future Productions of Wells of Equal Output....... 510 Use of Appraisal Curves for the Derivation of Generalized Future Decline Curves. 513 Theory of Generalized Curves Showing the Decline in Production...... 513 Suggested Methods for Making Closer Estimates.............. 517 Use of Logarithmic Coordinate Paper.................... 518 Summary................................ 520 Introduction Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in production, the rapidity of decline depending on the output of the wells and on other factork governing their productivity. The production curve of a well shows the amount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, will furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property maybe judged, and proper depletion and depreciation charges may be made on' the books of the

Jan 1, 1918

By Lyman Johnson

Single crystals qf copper in "single slip" orientatiorzs have been deformed in compression. During defortnation all of the independent deformation parameters have been measured. These parameters consist of thefive strain components and three components descrihing the lattice rotation. By a finite strain analysis these pararmeters , forrming a deformation gradient martrix, are related to the amounts of slip on each of the twelve slip systems. The results show that the amount of secondary slip is about equal to the amount of primary slip. This is an order of magnitude larger than has been believed previoutsly. ACCORDING to early theory and experiments, when a single crystal of a fcc metal is deformed in tension or compression it should deform by slip on only one slip system until the stress axis reaches a symmetrical orientation.' However. the observation of a large increase in the secondary dislocation density during ..single slip" makes it clear that some slip does occur on secondary systems. Knowledge of the amount and distribution of this secondary slip is essential to a complete understanding of the mechanisms of single-crystal deformation. Ahlers and Haasen 2 and Mitchell and Thornton1 have tried to detect the amount of secondary slip in single crystals of silver and copper, respectively. Each simultaneously measured the angle A, between the tensile axis and the primary slip direction and the length 1 of a gage section of the specimen after incremental amounts of deformation in tension. The measured A, was then compared with the theoretical single slip angle hp. given by sin Ap = j sin . hO where ?o was the initial angle between the tensile axis and the primary slip direction and lo was the initial gage length. In both sets of experiments a small but systematic difference between ?e and ?p was found. This difference must be due to the occurrence of secondary slip. However, as Mitchell and Thornton1 pointed out. nothing quantitative can be said about the amount and distribution of this secondary slip from the measurements that they made. The reason that no quantitative conclusions could be made is because no unique solution for the distribution of slip on the twelve fcc slip systems can be determined from only two measured deformation parameters such as A and 1. There are, in fact, eight independent macroscopic deformation parameters that can be measured when a single crystal undergoes a homogeneous deformation. Physically these can be thought of as the five finite strain components and the three angles describing the crystal lattice rotation. All eight of these parameters were measured by Taylor4,5 for aluminum deformed in tension and compression. At that time the concern was to show that slip occurs on {111 (110) systems in fcc metals, and the mathematics were not available to determine what slip distributions were compatible with the measurements. In this paper the mathematics6,7 are developed that allow the slip distribution to be determined from these measurable macroscopic deformation parameters. The analysis is applied to the measurements of the strain and lattice rotation of copper single crystals deformed in compression. The results show that the amount of secondary slip is an order of magnitude larger than had previously been thought. CRYSTALLOGRAPHIC DESCRIPTION OF A HOMOGENEOUS DEFORMATION The deformation of a solid body can be represented by a transformation matrix F that transforms the un-deformed state into the deformed state. Consider a vector X connecting two material points in the unde-formed material and the vector x connecting the same two material points after deformation, where both vectors are referred to the same set of Cartesian axes. The final vector x is related to the initial vector X by the equation: X = FS. [2] Eq. [2] can be considered as the equation defining F, which is called the deformation gradient matrix. Its components are: If the deformation is homogeneous, the transformation is linear and the components of F are constants. Using subscript notation, if P is the unit vector in the initial direction of a material line, the components of the unit vector p in the direction of the same material line after deformation are given by:

Jan 1, 1970

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250' to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,' and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By J. B. Dilworth

The purpose of this paper is, first, to give a general account of a little-known coal-district of SE. Kentucky, its topography, drainage, and mineral resourcee, for those who may be interested in its economic development; and secondly, so to describe the geologic features of the field as to furnish available data to those engaged on the broader problems of Appalachian coal-geology. The data from which the major portion of the paper has been prepared were obtained, in professional investigations for private individuals and corporations, within the last decade. The area under review, defined by a heavy line on the map, Fig. 1, lies between Little Black and Pine mountains, and extends from Harlan on the west to a N-S. line crossing Looney creek 3 miles from its mouth on the east. This area can be divided for description into a Western and an Eastern Division. The character of investigatioil pursued in the Western Division, below Fugitt creek, was very different from that employed in the Eastern. In the former, only a rapid reconnois-sance was attempted: such coal-openings as had been made by prospectors or by citizens in obtaining fuel were visited, their

Jan 1, 1913