Search Documents

By R. G. Grieves, G. Thodos

A method is presented for the accurate calculation of the cricondentherm and cricondenbar pressures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain six and quite possibly any number of components including paraffins, isoparaffins, olefins, acetylenes, naphthenes and aromatics. The approach is similur to that used for calculating critical pressures and cricondentherm and cricondenbar temperatures. The critical pressure, the normal boiling point and the approximate vapor pressure behavior of each component are all that art required. A stepwise culculation procedure is necessary for mixtures containing more than two components. From an analysis of 22 binary systems and 118 mixtures, the average deviation of calculated cricondentherm pressures from reported values is 2.4 per cent. For nine multicomponent mixtures the average deviation is 1 per cent. Considering 19 binary systems and 108 mixtures, the average deviation of calculated cricondenbar pressures from reported values is 1.7 per cent. For 15 multi-component mixtures, the average deviation is 2.2 per cent. INTRODUCTION A knowledge of the phase behavior in the critical region of multicomponent hydrocarbon mixtures is of value both in industrial processing operations and for the optimum operation of gas condensate reservoirs. Accurate methods of calculating the critical temperatures and critical pressures4,6,7,8,9,23 and cricondentherm and cricondenbar temperatures6p10 of multicomponent hydrocarbon mixtures are available in the literature. If the cricondentherm and cricondenbar pressures could be calculated with equal accuracy, the entire phase diagram of a multicomponent hydrocarbon mixture could be well approximated. The work of Etter and Kay6 is limited to systems containing the normal paraffins and has not been tested on systems containing a heavier component than heptane. In addition, the development of their multicomponent equations is based upon a limited number of mixtures containing from three to six components. Silverman and Thodos have considered systems containing both paraffinic and non-paraffinic hydrocarbons, but their correlation is limited to binary systems and is highly inaccurate for methane systems. Eilerts has done extensive work on the cricondenbar pressure; he has produced an excellent correlation for binary systems. However, his procedure for multicomponent mixtures is chiefly useful for highly complex mixtures requiring a knowledge of the vapor-liquid equilibrium behavior of the mixtures; he has not considered the cricondentherm pressure. The objective of this study was the development of an accurate and rapid method for the calculation of the cricondentherm and cricondenbar pressures of multicomponent mixtures containing all types of hydrocarbons and having a wide volatility range. The approach that was adopted is similar to that used by Grieves and Thodos for cricondentherm and cricondenbar temperaturesl0 and for critical pressures.9 However, methane systems had to be considered separately and a modified stepwise calculation procedure was utilized for the cricondertherm pressure. The correlations were developed in a manner similar to those for critical pressures and cricondentherm and cricondenbar temperatures. Based upon binary data reported in the literature it was observed that the ratios of cricondentherm and cricondenbar pressure to the pseudocritical pressure (molar average), pt/ppc and pp/ppc, respectively, in two-component systems depended upon the mole fraction of the low-boiling component and upon the diversity in properties of the two components. A dimensionless boiling-point parameter Tb,/Tb was chosen to represent the diversity in properties of the components. For a binary system, Ti,'is the molar average of the normal boiling points of the two components involved. For a multicomponent system it is either the molar average of the normal boiling points of all of the components involved or the molar average of the normal boiling point of the pure low-boiling component and of the atmospheric boiling point of the low-boiling-free mixture of

Jan 1, 1965

By B. B. Kunkle

The history of this refinery has been one of expansion. It now has the capacity to produce 240,000 tons of cathodes annually. A general flowsheet and descriptions of the plant layout, operations involved, and equipment used at one of the world's largest and most modern electrolytic copper refineries are presented. THE El Paso copper refinery of Phelps Dodge Refining Corp. was originally constructed by the Nichols Copper Co., in association with Phelps Dodge Corp. and the Calumet & Arizona Mining Co., in order to refine anode copper produced at the smelters of the two latter companies. Initial production was obtained from the plant in January 1930 and its annual refining capacity was 100,000 tons of anodes. In order to keep pace with Phelps Dodge Corp.'s increasing copper production in the Southwest, it became necessary in 1937 to increase the El Paso plant's refining capacity to 160,000 tons of cathodes annually. This was accomplished by adding two sections to the electrolytic tank house, increasing the number of anodes placed in each commercial electrolytic tank from 33 to 37, and making changes in the dc circuits which made it possible to put three generators on each of the two circuits instead of two, thus increasing the amperage on each circuit from 10,000 to 14,800 amp. The capacity of the two furnaces from which refined shapes were cast was increased by raising the sidedoor bays on the furnaces 6 in. An increase of 70 pct in the productive capacity of Phelps Dodge Corp.s Morenci Branch in 1942 again made it necessary to expand refining capacity. In order to accomplish this, Defense Plant Corp. set up a project to increase the capacity of the El Paso plant to 240,000 tons of cathodes annually. This project consisted of enlarging the tank house approximately 50 pct, the construction of another wire- bar furnace, and corresponding increases in other departments where necessary. The engineering work on this expansion was begun in March 1942. Actual construction was under way by August 1942, and the work was completed by March 1944. These additional facilities were purchased from Defense Plant Corp. by Phelps Dodge Refining Corp. in August 1949. The plant is in El Paso about eight miies east of the center of the city and near Highway 80 and the main lines of the Southern Pacific and Texas & New Orleans railroads. The plant site covers approximately 494 acres of company-owned land that is ideally adapted for its use, being well-drained sandy soil and having enough slope so that a minimum amount of excavation was required when the plant was constructed. There is still ample room on the plant site for any future plant expansion. The plant is constructed on four different ground levels and so arranged that the unrefined copper is unloaded on the highest level at the north side of the plant and the refined copper is shipped out from the lowest level on the south side of the plant. The receiving or unloading platform, weighing and sampling rooms, main floor of the tank house, acid and condensate storage tanks, and the slimes and copper sulphate plants are on the first or highest level. The tank house basement, yard scales, charging and furnace bays, balloon flue and stack, brick-storage building, substation and power house, boiler feedwater treating plant and pump house, water storage tanks, and change houses are on the second level. This second level also contains ample yard area for setting-up furnace charges, and for storage of custom scrap, cathodes, scrap anodes, blister, coke, and poles. The casting wheels, inspection conveyors, cathode shears, wire-bar scalping machine, slag

Jan 1, 1952

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors' results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. ' The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

By H. Van F. Furman

As the cyanide-method for the extraction of gold from ores is extensively used in the United States and elsewhere, and appears destined to prove a factor of increasing importance in the metallurgy of gold, a description of the latest laboratorymethods may prove of interest. The history of the development of the process in the United States has been analogous to that of all new processes. Many failures are to be recorded and a few successes. It is the opinion of the writer that, had the following simple tests been better understood, many of the failures would not have occurred, and we should probably have a larger number of successful plants in operation. While the process is not simple, but requires a high degree of chemical and engineering skill, the determination of the adaptability of an ore to the method is generally not difficult. While the laboratory-results will not always coincide with the actual results obtained in the mill, they will serve as a guide and control on the working of the mill, and mill generally suffice to determine if the ore can be

Jan 1, 1897

By H. W. Seamon

THE data here given were obtained by 1500 tests made, by the United Verde Copper Co. to determine the most economical air pressure for the operation of hammer drills under the varying conditions of use, and to investigate the variation in drilling speed at different air pressures Twelve models of drills were used at gage pressures ranging from 40 to 130 lb. No effort was made to harmonize theory and practice; but rather to formulate empiric rules that would cover the. average variation of the results obtained. These rules on the performance of hammer drills, based on the air pressure as the main variable, however, are not necessarily of universal application, but they apparently satisfy the results obtained in this series of tests. The drilling conditions at this property vary widely; an average of twenty-one machine shifts to a 3-ft. (0.9-m.) round has been found necessary in some of the development work, while an, advance of 56. ft. has been made in seven shifts in the "oxide" ground. This range pre-eludes the adoption of one type of drill as a standard; consequently almost every kind of hammer drill sold in this country has been tested. At present, sixteen models are in use, of which two types of the heavy (150 to 160 lb.) mounted drills, one of the light mounted drill, one stoper, and two hand plugging drills are considered as standard.

Jan 1, 1921

By William P. Blake

The occurrence of siderite in beds of considerable thickness in the clay formations of Martha's Vineyard, Mass., may have some economical importance, and is at least interesting in a scientific point of view.

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

By H. M. Howe, E. C. Groesbeck

That the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First, each particle of any composite liquid, whether it be an aqueous solution or a molten metal, in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the existing temperature, and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already solidified; A, Fig. 1. The other part is fusible at the existing temperature and hence remains molten. In the case of carbon steel, the part of each drop which actually solidifies is poorer in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying half-drop enriches the other half-drop in carbon, and thus makes it unfreezable at the existing tern- By this mechanism there arises during solidification a "littoral" or shore layer of liquid B, Fig. 1, bathing the already solidified walls, and more fusible than either those walls or the great remaining central mass of liquid or " deep sea " C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal could get past this littoral layer and come into contact with the solid walls, it would in turn solidify, and like its predecessors would split up in solidifying into a less fusible half-drop which would attach itself to those . walls and a more fusible one which would remain molten. Thus we see

Jan 1, 1920

By A. Q. Tool

THE necessity of accurate temperature measurements in the glass-making industries is today being much more widely appreciated than in the past. The introduction of the modern simplified and perfected pyrometric methods in connection with exact regulation of furnace temperatures has caused a marked improvement in the glass product with a quickened rate of production. An example of the processes in which much improvement has been and still can be made is that of annealing or heat-treating the glass. This is one of the most delicate processes in glass manufacture and one that requires a most careful furnace control. The heat treatment is undertaken to decrease the possibility of breakage and, in glass for fine optical instruments, to prevent serious warping of accurately ground and polished surfaces and to make the glass more uniform throughout to the passage of light waves. These objects are accomplished by removing all the harmful stresses that exist in a piece of glass when it has been cooled too quickly or unevenly. Such stresses exist, for example, after it has been pressed, cast, or otherwise worked. Thus the process of annealing consists of heating the glass evenly to the temperature at which it softens just enough to relieve these stresses in a reasonable time and then cooling slowly and uniformly until the glass hardens again. Accordingly, the things that must be investigated and determined in order to anneal glass without loss of time are, the annealing temperature, the time that the glass should be held at this temperature while the stresses relax, and the quickest cooling procedure that will give satisfactory results. After these characteristics of the glass are known the problem is one of pyrometry and temperature control entirely. In cases when it is known that a glass article will be required to withstand some definite type of heat or mechanical shock it is often possible, by a proper heat treatment, to produce such a distribution of the stresses in the glass that it will be enabled to resist these shocks more effectively.

Jan 9, 1919

By R. A. Breitrick, J. N. Swinderman, J. J. Cooper, H. L. Bauer Jr.

The Robinson Mining District, near Ely, Nev., is one of the major porphyry copper districts in the world. Within the district is an eight mile long east-trending zone of altered porphyry, metamorphosed sedimentary rocks, and sulphide mineralization surrounded by Paleozoic limestone, dolomite, shale and sandstone, Tertiary volcanics, and Quaternary alluvium. Six major disseminated ore deposits have been exploited in this zone. About 20% of the district production has come from disseminated ore in metamorphosed sedimentary rocks found adjacent to altered quartz-monzonite porphyry. The following brief statements summarize some of the relations between porphyry alteration, metamor-phism, and mineralization: 1) Disseminated copper ore does not occur in unaltered porphyry or in m-metamorphosed sedimentary rocks. 2) Sedimentary rocks have been only weakly metamorphosed where intruded by unaltered porphyry. 3) Intensely metamorphosed sedimentary rocks are found only adjacent to altered porphyry. 4) Many hydrothermal minerals are common to both altered porphyry and adjacent metamorphosed sediments. 5) Disseminated ore is found in altered porphyry and adjacent metamorphosed sedimentary rocks. 6) In general, there is a direct correlation between grade of ore in porphyry and copper content in the adjacent rocks. 7) Chemical changes in the altered porphyry and metamorphosed rocks appear to be related. The foregoing relations support a hypothesis that the porphyry alteration, the metamorphism of the sedimentary rocks, and the ore deposition were all part of a continuous hydrothermal process which probably closely attended the porphyry intrusion. The Robinson Mining District, most often referred to as the Ruth or Ely District, is located in eastern Nev. and is one of the major porphyry copper districts of the world. Production from 1908 through 1962 was nearly 250 million tons of ore averaging a little over one percent copper with a total metal value of nearly one billion dollars. The ore has been produced from six major disseminated-type deposits with the Liberty Pit deposit accounting for 70% of the total district production. Less than one million tons of base metal and gold ores have been produced from the replacement-type deposits of the district. Approximately 20% of the district production has come from underground mining operations; the pit ore has been mined with shovels and removed by train haulage, truck-train haulage combinations, truck haulage, and presently by a combination truck-skip system. Many of the ore deposits formerly worked by underground methods have been and are being exploited by open pit methods. (See Fig. I.) Two co.&apos;s have accounted for virtually the entire production from the district. In 1958 Kennecott Copper Corp. acquired the district assets of Consolidated Coppermines Corp. and is now the sole ore producer in the district. Present operations are confined to the Liberty Pit where 22,500 tons of ore averaging a little less than 0.8% copper is mined per day. Cutoff grade is 0.4% copper, and the stripping ratio is three to one. The ore is hauled by rail 23 miles to the McGill Reduction Plant where it is concentrated to about 20% copper. Molybdenite is recovered as a by-product in the mill. The copper concentrates are smelted in McGill, and the blister copper is shipped for refining to Balt. where gold, silver, platinum and palladium are recovered. The Robinson Mining District has been well known as a porphyry copper district for the past fifty years, but many geologists are unaware of the fact that a large portion of the production has come from disseminated ore found in metamorphosed sedimentary rocks. The scope of this paper describes the occurrences of disseminated ore in the various metamorphosed sedimentary rocks, and presents evidence for the hypothesis that these ores are genetically, spacially, and coevally related to the disseminated ore in the porphyry rocks. Publication of this paper was granted by the management of Kennecott Copper Corp. A. H. James suggested and encouraged the writing of the manuscript. Special mineralogical and spectrographic analyses were performed by the Kennecott Research Center. The deposits of the district have been studied by many geologists since the turn of the century, and

Jan 1, 1964

By Don L. Kendall, Martin G. Buehler

A simple physical model has been developed to fit carrier-removal data in silicon irradiated near room temperature with reactor spectrum neutrons. Commonly observed donor and acceptor defect energy levels are assumed to be introduced linearly with neutron fluence. The donor levels (in ev) are Ev + 0.16, Ev + 0.27, and Ev + 0.31 and the acceptor levels are Ec - 0.55, Ec - 0.40, and Ec - 0.1 7, where Ev and Ec are the valence and conduction band energies, respectively. The introduction rates of each level are adjusted to fit literature initial carrier-removal rate data. When normalized with respect to the Ev +0.27 level, the relative values of introduction rates are 5.3, 1.0, 3.1, 1.0, 2.0, and 20.0, respectively for the six levels indicated above. To fit p-f (hole concentration vs neutron fluence) and n-f (electron concentration us neutron fluence) data, the introduction rates are multiplied by a factor which preserves the relative values given above. This factor depends upon irradiation temperature, reactor energy spectrum, neutron fluence calibration, and oxygen content of silicon. An extensive study of the effect of neutrons on carrier-removal in silicon irradiated with reactor spectrum neutrons (E > 10 kev) has been given by Stein and Gereth1 (SG) and Curtis, Bass, and Germano&apos; (CBG). They measured initial carrier-removal rates for both p- and n-type silicon over an impurity range typical of silicon devices. In this work, we attempt to fit a simple theory to this data to establish a usable relationship between hole and electron concentration, p and n, respectively, and neutron fluence f. The p-f and n-f relations are needed to assist in the design of neutron tolerant silicon devices and are needed to clarify presently used empirical resistivity-fluence relationships.3 Neutron damage in silicon produces a variety of defects ranging from simple point defects to defect clusters. For the purpose of this treatment, we assume that simple point defects dominate carrier-removal effects. In contrast to this view, stein4 has proposed that defect clusters are responsible for a significant portion of carrier-removal effects. In the following section, it is shown that the carrier-removal effect in n-type silicon with an electron concentration less than 1015 cm-3 can be explained adequately by assuming that the divacancy is the dominant defect and that its introduction rate is independent of the electron concentration. For electron concentrations greater than 1015 cm-= an additional acceptor defect center is needed, and for simplicity the A-center (vacancy-oxygen pair) has been chosen. Although the E-center (vacancy-phosphorus pair) can account for some of the results, the A-center was chosen because the E-center requires a more involved treatment which the presently available data do not justify. In p-type silicon three radiation-induced donor levels are assumed, namely the divacancy and two other centers of unspecified nature located at Ev + 0.16 ev and Ev to 0.31 ev. The donor divacancy at Ev + 0.27 ev is assumed to be introduced at the same rate in p-type as in n-type. However, this rate is too low to fit p-type initial carrier-removal data. The dominant centers in p-type silicon are assumed to be the Ev + 0.16 ev and Ev + 0.31 ev levels where the latter is not the divacancy. The introduction rates are chosen to fit initial carrier-removal rate data. Assuming that the introduction rates are independent of Fermi level, the ratio between them is fixed for subsequent p-f and n-f calculations. Using the same ratios, the initial carrier-removal rate data1,2 as well as p-f and n-f data1,5 can be fit provided the absolute value of the introduction rates are adjusted to account for irradiation temperature, reactor energy spectrum, neutron fluence calculation, and the oxygen content of silicon. THEORETICAL ANALYSIS This analysis is basically the same as that used by Hi116 to analyze electron damage in silicon except we express the degree to which an impurity level is ionized not in terms of the Fermi level, but in terms of carrier concentration. Landis and pearson7 have used the latter approach to analyze y-damage in silicon. Neutron-induced defects responsible for carrier-removal at room temperature are assumed to be simple point defects with no interaction between defects so that they may be represented by discrete energy levels. It is also assumed that no constituent of a defect complex is used up and defects stabilize shortly after irradiation. Defects are assumed to be introduced linearly with fluence according to the product Rtf where Rt is the defect introduction rate and f the neutron fluence. Taking into account the ionization of defects according to Fermi statistics, and considering charge neutrality where minority carriers are neglected, the n-f relation is where no is the preirradiation electron concentration. The parameter Nt is the electron concentration at which the ionized defect concentration is one-half the total defect concentration (Rtf) or where Et is the defect energy level. For silicon at 300°K, ni = 1.45 X 1010 cm-3 and Ei = Ev+ 0.542 ev which was determined using Ec — Ev = 1.11 ev and me* = 1.07 mo and mh* = 0.558m0. The spin degeneracy factor, which usually appears as a number multiplying the Nt/n term of Eq. [1], is taken as unity. In effect, this factor has been incorporated into the defect en-

Jan 1, 1970

By H. R. Froning, R. O. Leach

In wertability alteration flooding, a chemical agent is rnoved through a reservoir by the flood water to increase oil recovery by decreasing the degree of wetting of the rock by the oil. Substantial amounts of the chemical may be lost during movement through the reservoir. The extent of the loss, and therefore the economics of the process, depends in some cases on factors which are difficult to reproduce in the laboratory. Therefore, a short-duration, low-cost field test method is needed to permit evaluation of chemical requirements under actual field conditions. This paper describes a small scale rest conducted at a single well for measuring chemical requirements, thereby giving a more reliable evaluation of this important factor in the applicability and economics of the process. In the rest a small wafer slug containing the chemical agent and a nonadsorbed tracer is displaced into the reservoir by a known volume of wafer. The well is then placed on producrion. Chemical loss per barrel of pore volume contacted is calculated from [he fractional recoveries of the agent tested and the nonadsorbed tracer. The method has been used to determine within the actual reservoirs the chemical requirements for both a sandstone and a dolomite reservoir. Several chemical agents are potentially available for wettability alteration flooding, although none is universally applicable. For some applications of the method, chemical costs per barrel of additional oil recovered can be substantially less than one dollar. INTRODUCTION Wettability alteration flooding provides a means of increasing oil recovery from reservoirs by decreasing the degree of wetting of the rock by the oil and increasing the displacement efficiency of the flood water. Earlier studies demonstrated a relationship between oil recovery during waterflooding and the degree of wetting of a rock surface by an oil. The application of wettability alteration flooding to the Harrisburg field of Nebraska provided a field test&apos; of this recovery process. Subsequently, additional laboratory and field tests have developed additional procedures for evaluating wettability alteration flooding, and have indicated where the process may be applicable. Applicability of this process to specific reservoirs is determined by a progression of tests to determine sus- ceptibility of the reservoir to alteration of its wettability, to indicate the degree of recovery improvement and to estimate the amount of chemical required to process the reservoir. The economics of applying improved oil recovery processes depends not only upon the degree of improvement in oil recovery achievable by the process but also upon the process costs and the timing of the income and the investment. Emphasis in this paper is on the expenditure aspects of the process. The work reported in this paper indicates that the chemical investments required for wettability alteration flooding are substantial. For evaluating the economics of a potential flooding application it is imperative that a sound estimate of the chemical requirements be made for the reservoir. Generally, true reservoir conditions are not adequately simulated in laboratory chemical propagation tests. Because of wide well spacings, many years might be required to obtain chemical propagation data from conventional pilots or inter-well tests. Consequently, n short-duration, low-cost method is needed to determine chemical requirements in the field. The potential applicability of wettability alteration flooding is discussed, as well as the economics of wettability alteration with respect to the inherent and imposed restrictions on the timing of income and investments. DETERMINATION OF CHEMICAL REQUIREMENTS In the process of moving a chemical bank through reservoir rock, some of the chemical agent lags too far behind the flood front to be effective or is otherwise lost to the reservoir system. The extent to which these losses occur overshadows the reductions in chemical concentration due to diffusion and to mixing with the reservoir fluids. Experience indicates that almost without exception, chemicals which induce a wetting change undergo either sorption reactions or chemical reactions with mineral constituents of the pore surfaces. Other reactions may occur between the added chemical and the reservoir oil and water. Even in limiting consideration to reactions of the relatively inexpensive inorganic salts, bases and acids, the reactions may be exceedingly complex. Reservoir pore surfaces consist of more than silica in sandstone reservoirs, and more than calcite or dolomite in carbonate reservoirs. Many mineral species are present, each exhibiting specific tendencies to react with an injected chemical. The reactions which occur can consume enough of the agent to have an important effect on economics. These reactions can cause a change in pH of the chemical bank, or may remove some of the active chemical by precipitation, adsorption or reaction to form a new chemical which may or may not be effective in

By C. E. Lundin, M. Hansen, D. J. McPherson

PRIOR work on the Zr-Cu phase diagram by Alli-bone and Sykes,&apos; Pogodin, Shumova, and KUGU cheva,&apos; and Raub and EngeL3 as confined largely to copper-rich alloys. The investigations of Raub and Engel were the most recent and seemingly the most complete of these. Alloys from 0 to 68.3 pct Zr were studied principally by thermal analysis and microscopic examination. These authors reported an inter metallic compound ZrCu, (1116°C melting point) and two eutectics, one at 86.3 pct Cu (977°C mp) and the other at 49 pct Cu (877°C mp). The solubility of zirconium in copper was reported to be less than 0.1 pct at 940°C. The zirconium melting stock consisted of Westing-house "Grade 3" iodide crystal bar (nominally 99.8 pct pure). It was treated by sand blasting and pickling (HF-HNO, solution) to remove the surface film of corrosion product, resulting from grade designation tests. The crystal bar was cold rolled to strip, lightly pickled again, and cut into pieces approximately 1/32 in. thick and 1/4 in. square. These were cleaned in acetone, dried, and stored for charging. The high-purity copper (spectrographic grade) was supplied by the American Smelting and Refining Co. with a nominal purity of 99.99 pct. These copper rods were rolled to strip, cut into squares the same size as the zirconium platelets, cleaned in acetone, dried, and stored. Equipment and Procedures The equipment used for melting and annealing the zirconium binary alloys and for the determination of solidus curves has been described in connection with previous work on the Ti-Si system&apos; and in recent papers in this series describing the studies on eight binary zirconium systems.5-&apos; Techniques employed for preparing and processing the alloys were also similar to those used in the above references. Ingots of 20 g were melted under a protective atmosphere of helium on water-cooled copper blocks in a nonconsumable electrode (tungsten) arc furnace. The ingots were homogenized and cold-worked prior to isothermal annealing to aid in the attainment of equilibrium. The specimens were heat-treated in Vycor bulbs sealed in vacuo or under argon, depending on the temperature of the anneal. Quenching was accomplished by breaking the Vycor bulbs under cold water. Temperature control was within ±3OC of reported temperatures. Thermal analysis was primarily relied on to determine eutectic levels, peritectic levels, and compound melting points. The induction furnace incipient melting technique was also used but did not provide the accuracy obtained by thermal analysis in this system, which involves much lower solidus temperatures than the other zirconium systems. A special technique for the determination of characteristic temperatures was employed in the case of several intermediate phases and their eutectics which displayed very small differences in melting temperatures. Specimens were sealed in Vycor bulbs and annealed at a series of very accurately controlled temperatures. Metallographic examination was then employed to reveal incipient melting. Furnaces and techniques in general were described previously.&apos; The echant used was 20 pct HF plus 20 pct HNO3 in glycerine unless otherwise stated. Results and Discussion The chemical analyses of the majority of alloys prepared for the determination of phase relationships in this system are given in Table I and a brief summary of the equilibrium anneals employed is given in Table 11. In a preliminary program, alloys containing 1, 4, and 7 pct Cu were annealed for three different times at each of the temperatures 700°, 800°, and 900°C. No change in the relative amounts of phases present was detected after 350, 150, and 75 hr at the above temperatures, respectively. The times listed in Table II were accordingly chosen as a result of these preliminary tests. Zirconium-rich alloys containing from 0.1 to 10 pct CU were reduced by cold pressing from 58 to 8 pct, depending upon thk alloy content, homogenized for 7 hr at 900°C, and then reduced 80 to 13 pct by cold rolling, again depending upon copper content. Other alloys were studied in the cast, or cast and annealed conditions. The contracted scope of investigation for this system included the range 0 to 50 atomic pct Cu. This approximate region is shown in Fig. 1. Due to evidence of phase relationships departing considerably from those proposed by Raub and Engel" in the 50 to 100 atomic pct range, the investigation was extended to cover this composition area rather thoroughly also. Fig. 2 is a drawing of the entire diagram. The labeling of some phase fields was omitted in Fig. 2 for the sake of clarity. An expanded view of the zirconium-rich region, with the experimental points necessary for its construction, is given in Fig. 3. The generally accepted value of Vogel and Tonn8 or the allotropic transformation a + 862&apos; ±5OC, was employed in the construction of these diagrams. A careful study revealed that the "Grade 3" crystal bar used in this investigation actually transforms over the approximate range 850" to 870°C, due to impurities. It must be expected that this two-phase field in unalloyed zirconium will cause some departures from binary ideality in the very dilute alloys. Zirconium-rich Alloys: The a + ß transformation temperature is decreased from 862" to about 822°C by increasing amounts of copper. Thus, a eutectoid reaction, fi ß a+ Zr,Cu, occurs at a composition of about 1.6 pct Cu. The eutectoid level was determined to lie between the alloy series annealed at 815" and 830°C. The placement of this eutectoid temperature

Jan 1, 1954

By V. F. Hollister, M. Bernstein

The Copaquire porphyry copper deposit lies in an island of pre-Upper Tertiary rocks surrounded by Quaternary and Upper Tertiary formations. The pre-Upper Tertiary appears to be a horst block in a typical basin-range setting. Major right lateral faults have been mapped within the range from Chuquicamata north to Copaquire. All of the major porphyry copper deposits known in the block (e.g., Quebrada Blanca, El Abra, Chuquicamata, and Copaquire) are on or are very close to one of these major right lateral shears. In the Copaquire district, an epizonal igneous complex with diorite, quartz diorite, quartz monzonite, and intrusive dacite (in that intrusive order) invade folded Jurassic shale. Mineralization appears spatially and temporally associated with the quartz monzonite porphyry and dacite. Alteration zoning shows two separate core phyllic (quartz-sericite-pyrite) zones within one large argillic (clay-pyrite) zone. A propylitic (chlorite) zone is peripheral to the argillic zone. No potassic zone has been recognized yet at the surface. The intrusive petrology together with the phyllic, argilic, and propylitic alteration zoning as well as the chalcopyrite-molybdenite ore mineralogy characterize this deposit as being typical of the Lowell and Guilbert model. Copper and molybdenum minerals appear to be most strongly developed in the phyllic zone, in either a breccia or a zone of veinlets and stockwork which trend dominantly northeast, conjugate to the district&apos;s largest fault, the Sulfato fault. The setting is basically similar to that found in some other porphyry copper deposits in this block, in that the ore body is a zone of veinlets which appear to be genetically related to movement on a major north-south trending right lateral fault. The presence of the major fault in each deposit, and the speculative hypothesis that paleo-subduction zone operated at the time of mineralization, suggest the possibility that mineralization took place when a major fault permitted escape to the surface of cal-calkalic magma generated in a subduction zone as proposed by Ericksen. A hypothesis such as that proposed by Ericksen explains the near linearity of porphyry copper deposits in Chile, since the source of calc-alkalic magma would exist at about the same distance from a paleo-trench throughout the length of the paleo-subduction zone.

Jan 1, 1976

By Morris Cohen

It has been known for several years that in certain age-hardenable alloys precipitation of finely divided particles occurs simultaneously with the changes in physical properties; while, in other alloys, these changes take place prior to, or without any, precipitation. The silver-copper alloys are generally considered to be the classical example of the first group, and the aluminum-copper alloys (duralumin) are typical of the second group. The two types of aging are explained by the precipilation theory and the knot theory respectively.‡ It is well recognized now that these theories do not conflict with each other; the one used for a given aging system depends upon which way the alloy in question happens to age-harden. However, previous work on the aluminum-copper al1oys1,2 has shown that if the aging temperature is raised sufficiently the hardening will be accompanied by actual precipitation. In fact, it is quite probable that all of the so-called knot-hardening alloys will harden by precipitation at elevated temperatures. Therefore, a combination of the knot and precipitation theories is necessary to give a complete picture of the agehardening of these alloys, and indicates that knot formation and precipitation are not independent processes. To test the generality of this concept, it is necessary to show that the alloys that commonly harden by precipitation will harden prior to precipitation if the aging temperature is sufficiently lowered. For this reason, it would be well to carefully re-examine the aging characteristics of the silver-copper alloys at aging temperatures somewhat below those used by previous investigators. If hardening can be detected prior to precipitation in these alloys, it will lend great weight to the idea that knot forma-

Jan 1, 1937

By Fred Allison

THE magneto-optic method of analysis had its origin in experiments1 which were designed to detect and measure a time lag in the Faraday effect and later to study this time lag as a function of the wave length of the light.2 Faraday discovered in 1845 that a beam of plane polarized light, when passed through a transparent, isotropic medium traversed by a magnetic field of force parallel to the direction of the light, suffers a rotation. The direction of rotation is reversed with the reversal of the magnetic field and its magnitude depends upon the strength of the field, the length of the path of light in the substance and the nature of the substance. This phenomenon of magnetic rotation is known as the Faraday effect. A question which had been of some interest for years was whether this power of a liquid to rotate polarized light is acquired instantly with the application of the magnetic field, that is, whether it is a case of instantaneity or whether there is a very small interval of time which intervenes between the application of the magnetic field and the consequent rotation of the light by the liquid; in other words, whether there is a time lag in the Faraday effect. Efforts to measure such a lag previously had met with failure. It was recognized at the outset&apos; that since a time lag had escaped detection it must be extremely small, if to a measurable extent it exists at all. It became necessary therefore to adopt a timing device capable of making measures of almost infinitesimally small intervals. The velocity of light served as this timing device, a modification of a method originally employed by Abraham and Lemoine3 being adapted to the requirements of the problem. Since light travels about 30 cm. in a billionth of a second and since settings in our observations may be repeated with deviations not exceeding 3 mm.,

Jan 1, 1932

The 128th meeting of the American Institute of Mining and Metallurgical Engineers constituted a two weeks trip through the Great Northland of Ontario and Quebec and was a most memorable occasion. The last visit of the Institute to Canada was made in 1907 when the mines, which now have brought world wide fame to some of the camps, were not yet dis-covered. The party reached its greatest numbers at Porcupine where 167 visitors and nearly one hundred local members participated. Five members of the party from the States were on the previous trip in 1907. They were Mr. and Mrs. L. D. Huntoon, John Stevenson and son and E. F. Eurich. The Minister of Mines for the Province of Ontario attached his private car to the "Mining Engineers&apos; Special" and made the complete trip through Ontario. This was a happy incident in many ways and gave the visitors an opportunity to discover a spirit of mutual accord between the Minister and mining industry that might well be emulated elsewhere. Two compartment cars and one standard Pullman with the Institute members from New York and the metropolitan district were attached special to the 6.15 p.m. Lehigh Valley train from New York, Sunday, Aug. 19, en route to Toronto, where was held the first session of the Institute&apos;s 128th Meeting.

Jan 9, 1923

[RECEIPTS Magazine, Advertising $ 32,823.60 Sale of Magazines 3,933.29 Total Magazine $ 36,756.89 Dues, Arrears 5,866.97 Dues Current 100,223.80 Dues of New Members 6,143.29 Dues in advance 1,586.32 Initiation fees 6,820.00 Sale of Transactions 5,464.99 Sale of Binding 5,618.90 Sale of Pyrometry Volume 336.30 Sale of Indexes and Emmons 106.10 Sale of Pamphlets 575.32 Miscellaneous Receipts 105.60 Interest on Bank Balances 1,217.67 Interest on Life Membership Investment 512.18 Interest on James Douglas Library Fund 5,678.67 Total Receipts $177,013.00] [ ]

Jan 1, 1925

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944