Search Documents

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946

By H. J. Hand

STATISTICAL methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,' written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science,, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should .they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. † Many Useful Statistical Devices Available.-Many statistical methods of attack are available for the analysis of plant data. It is the object of this paper to discuss applications of some of these methods to the solution

Jan 1, 1938

By R. W. Cahn, C. D. Graham

Two predictions of the oriented growth theory of recrystallization textures have been tested by measuring the orientation dependence of the rate of growth of a single grain into a strained single crystal of aluminum, and determining the orientations of artificially and spontaneously nucleated grains growing preferentially into strained aluminum single crystals. Growth rates are found to be insensitive to orientation, except that new grains with orientations similar to the matrix or to a twin of the matrix have very low mobilities. Similarly, new grains growing preferentially into a strained crystal have random orientations, except that orientations near that of the matrix or its twins are avoided. The predictions of oriented growth theory are thus not confirmed. BASICALLY, the oriented growth theory of re-crystallization textures1 rests on the assumption that the rate of growth of a recrystallizing grain depends strongly on the orientation of the growing grain relative to the strained matrix into which it grows. In particular, the theory holds that in face-centered-cubic metals the orientation which corresponds to maximum growth rate is one in which the growing grain and the matrix are related by a rotation about a common <111> direction. The amount of rotation, as derived from several kinds of experiments,2-1 has been assigned various values, generally in the range between 20" and 40". (A <111> rotation of 60" is a twin relationship.) The conclusion that boundary migration rates depend strongly on orientation is based almost entirely on indirect evidence; there have been very few direct measurements of boundary migration rates as a function of orientation.* " The present investigation was undertaken to provide such measurements, to help make possible a decision between the oriented growth and oriented nilcleation theories of recrystal-lization textures. The basic experimental program consisted of measuring the rate of growth of a single recrystal-lizing grain consuming a strained single crystal, with the orientations of both grains preselected so that the effect of orientation on growth rate could be determined. A prerequisite for such an experiment is a strained single crystal which will support the growth of a new grain but which will not spontaneously nucleate new grains on heating. That is, the crystal must support the growth of a grain nucleated artificially, but contain no recrystalliza-tion nuclei which will become active at the testing temperature. Beck was apparently the first to note that such a condition could exist," and to make use of the condition for am experiment of the type described here.&apos; The present work was actually suggested, however, by a report of Tiedema". " that an aluminum single crystal strip, oriented with a (111) plane in the plane of the strip and a < 112> direction parallel to the tensile axis, would not recrystallize after 20 pet extension even when heated almost to the melting point, provided that the strip was heavily etched before being heated. This result could not be duplicated in the present work. In fact, it was found that any crystal which deformed in multiple slip (<100>, <112> and <111> orientations) underwent spontaneous nucleation after 15 pet extension, even if etched. However, crystals which deformed in single slip, and which did not develop heavy deformation bands, could be extended 15 pet without showing spontaneous nucleation at temperatures up to 600°C. Crystals oriented within about 10o of <110> which developed heavy deformation bands could be extended 10 pet without showing spontaneous nucleation. In all cases a heavy etch was required to prevent nucleation. Etching was necessary because of the presence of an oxide layer on the crystal surface at the time of straining, which leads to preferential nucleation at the surface.&apos;&apos; Grain Growth Rates Experimental Procedure and Results—Aluminum strips of 99.6 pet purity (principal impurities 0.19 pet Fe and 0.12 pet Si), 1 mm by 1 cm in cross section, were grown into single crystals of controlled orientation by the strain-anneal method of Fuji-wara.&apos;"&apos; " A sharp temperature gradient was maintained in the strips during growth by lowering them into a salt bath controlled at 650°C. Crystal orientations were determined by the etch-pit method of Barrett and Levenson" to an accuracy of ±2O. The crystals were extended by 10 or 15 pet in a simple hand operated tensile machine. Crystal orientations were rechecked after extension, and were found to be in agreement with the orientations predicted by the formula of Schmid and Boas." After extension, the grip ends of the single crystal specimen were cut off with a jeweller&apos;s saw, and the crystal heavily etched (at least 20 pet wt loss) in hot 10 pet Na or KOH solution. A region of severe local deformation was then introduced at one corner of the strip, usually by cutting off the corner with shears. Heating this end of the strip caused a large number of new grains to nucleate at the sheared edge. One of these grains grew to occupy the full width of the strip. The appearance of the strip at

Jan 1, 1957

By C. G. Maier

COMMERCIAL processes of lead softening directly involve the behavior on fusion of mixtures of the oxides of antimony and lead, and the vapor pressures of these materials. Practically no quantitative data have been available for the discussion of lead softening from the point of view of the fundamental metallurgy of the process. The Pacific Experiment Station -of the United States Bureau of Mines, in cooperation with the University of California, in the course of its program of study of the fundamental properties of oxides and sulfides, recently made vapor pressure measurements upon the various forms of pure antimony trioxide.1 When these measurements were considered in connection with the softening and "fuming" furnaces which are often used for lead purification, an unexpectedly anomalous condition appeared. In brief, this anomaly consisted in the fact that in certain softening furnaces, where lead bullion of approximately 1 per cent antimony content was being treated at a temperature of approximately 1300° F., no appreciable volatilization of antimony occurred, there being produced only a "skim" containing from 15 to 20 per cent Sb, 65 to 60 per cent Pb, as mixed oxides. In the "fuming furnaces," where the temperature was only about 1400° F. and where an accumulation of "skims" from the primary softener was being treated with certain other antimony-containing materials, a considerable volatilization of antimony as oxide occurred; an "impure" skim of some 60 to 65 per cent Sb and 10 per cent Pb was also produced as mixed oxides. The latter material cannot be suitably treated in hearth-type or softener furnaces. The essential chemical difference between the first and second step is the customary use of some reducing material (such as petroleum coke) in the later operation. An obvious interpretation of the effect of coke in facilitating the fuming of the antimony is the supposition that the antimony may be reduced to metal, and volatilized as such. This supposition is improbable, however, when it is realized that a slight extrapolation of the vapor-

Jan 1, 1932

By A. J. Lyon, J. B. Johnson, Samuel Daniels

The wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating at 932&apos; F. (500" C.) for 2 hr., cooling in air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that" considerable improvement in the mechanical properties of copper-aluminum alloys may be obtained from suitable heat treatment applied to castings."&apos; Jeffries and Gibson8 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932" F. in a nitrate bath for 1 hr., quenching in fish oil, and reheating at 300&apos; F. for for 1 hr. Their results disclosed the facts that the ultimate strength and the percentage of elongation of sound alloys were usually, and quite uniformly, improved by heat treatment; that with the iron content ranging between 0.36 and 0.88 per cent. and the silicon content between 0.24 and 0.60 per cent. the effect of increasing the copper content (Tables 10

Jan 1, 1925

By J. W. Walker, G. J. Heuer, E. W. Hough

An improved apparatus is described for the deterrni-nation of interfacial tension* by the pendant drop method in the pressure range from 15 to 15000 psi and the temperature range from 100º td 280°F. The chief characteristics of this apparatus are reliability and ease of operation. Temperature control was accomplished by means of an electrically heated jacket which could he completely removed while cleaning the apptrratus. The cell was designed so that the camera could he placed about I in, from the window without overheating the carnera lens. Separate "0" rings employed to seal each window and corresponding window backup plate gave very reliable window operation at 10,000 psi. An extra pistorr-cylinder combination was added so that a high compression ratio could he attained when gas was employed as one phase in the pendant drop cell. Other essential parts of the system were similar to an apparatus already described.&apos; The interfacial tension for carbon dioxide and water varies from about 69 dynes/cm at 15 psi to about 19 dynes/cm at 1,250 psi for 100°F. For pressure.r between t,500 and 3,500 psi, the interfacial tension is between 32 and 24 dynes/cm at this temperature. The interfacial tension at 280°F varies from about 50 dynes/cm at 200 psi to about 17 dynes /cm at 10,000 psi. The maximum surface excess for carbon dioxide, assuming the surface excess of water to be zero, occurs at about 1,500 psi jor the 100°F isotherni and Itas a value of about -79 X 1014 mol/sq cm. At 160°F this maximum IS shifted to about 2,000 psi and has a value of about 10 X 1014 111ol/.sq cm. Other maxima, us well as several minima, are present at these and other temperatures. Judging from the data on the solubility of water in carbon dioxide at elevtrted pressures2,3, it appears that the principal maxinza natned are in regions of increasing solubility of the water in the carbon dioxide rich phase. INTRODUCTION AND APPARATUS A pendant drop interfacial tension apparatus which would accommodate an opaque liquid in a gas phase was constructed several ycars ago&apos; for industrial purposes. This apparatus was used as a starting point for the present development. The objective of the present development was to enhance reliability and convenience of operation. Other articles&apos;" have described pendant drop apparatus which could not accommodate a gaseous phase adjacent to the windows. A schematic diagram of the apparatus is shown in Fig. 1. The water used followed the path; A, intro-

By R. T. DeHoff, L. J. Buteau, J. Kronsbein

Network topology is introduced and used to describe sinter bodies at various stages of the sintering process. The matrices of incidence, loop-branch. tree-branch, and cut-branch are constructed and their relationship to the three-dimensional void space and the common two-dimensional bounding surface is established. The sintering body is assunzed to remain connected but this is not so with the void space. The topological invariants known as Betti numbers are related to this observed fact and provide parameters which measure the progress of the sintering process. They are extracted from the matrices by means of known algebraic operations. Experimental procedures are given which permit actual construction of the various matrices and determination of the Betti numbers by serial sectioning of the sinter bodies. A sinter body is produced by exposing a large number of metallic particles (0.00001 to 0.3 in. diam) to a temperature that is near but below their melting point. When these particles are maintained at such a temperature for a sufficient length of time, it is found that the interparticle contacts become welded. As time increases, these welds, often referred to as necks, grow. All of the space between the particles constitutes a single connected void; an ultimate consequence of sintering is the breaking up of the void into separated parts. A mathematical apparatus for describing the geometric characteristics of a sinter body at each stage of the process was first proposed by F. N. Rhinesl when he introduced the application of topology to this problem. He described the sinter body in terms of one of its topological invariants, the genus. The most important advantage of a topological description is invariance with respect to continuous deformations. This means that particle sizes and shapes need not be considered, resulting in considerable simplification and generalization of the geometric description. In the case of a sinter body, wherein the internal geometry is particularly complex, the simplification provided by topological concepts is absolutely essential. The important parameters in the Rhines model are the number of particles and the interparticle contacts. The invariant considered called genus is given by Euler&apos;s formula for the connectivity of two-dimensional surface of the sinter body. This surface includes the pore-solid interface. The Euler formula is G = C - P + 1 [1] where C = number of interparticle contacts, P = number of particles, and G = genus of the surface bounding the sinter body. In topology the term genus may be used to mean the number of self re-entrant cuts that can be made on a closed surface without dissecting it into more than one connected surface. Its use is restricted to the surface and does not apply to the three-dimensional volume enclosed or excluded by it. In the case of sintering, the volume enclosed by the surface is defined as the sinter body; the volume excluded will be referred to as the void space. There is an intrinsic reason for using genus as a characteristic number associated with a sinter body. The genus is related to the Gaussian curvature by the integral of the product of the principal curvatures taken over the entire surface of the sinter body, as given by

Jan 1, 1965

By C. C. Furnas, T. L. Joseph

It is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investiga-tion1,2 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper. Importance of Gas-solid Contact One of the authors has pointed out in a previous report? that the operation of the blast-furnace process is entirely dependent on contact between the gas stream and the solid particles in the stock. The gas stream carries the necessary heat as well as the carbon monoxide molecules that do the work of rednction. In the parts of the furnace in which there is little or no contact between the gas stream and the solids there can be little work of reduction. Obviously, the part of the apparatus that is not doing the work for which it is intended is inefficient; the ideal condition is one in which all portions of the stock column are

Jan 1, 1929

By A. B. Wilder

We study the past Because it is a guide to the present and a promise for the future. The struggle for a better world is strengthened By the hopes, ambitions, and deeds Of those who were before us. As we look backward Our attention is directed forward. ONE hundred years ago, the manufacture of steel from molten pig iron without the use of fuel first began. In the earlier part of the nineteenth century the crucible process was the principal steelmaking method. It was a costly process, producing only a few pounds of steel at a time; so, most of the ferrous metal output was in the form of wrought or pig iron. With the perfection of the converter technique it became possible to produce low cost steel by the ton, thereby completely changing the structure, not only of the ferrous metal industry, but also of industrial production in general. This was the turning point from the Iron Age to the Age of Steel. William Kelly (Fig. 2), Sir Henry Bessemer (Fig. 1), and Joseph G. Martien experimented with the process before 1856. William Kelly began in Eddyville, Ky., in 1847 and has been given credit for first discovering the principle of the pneumatic converter process. Several years later in England Henry Bessemer independently conceived a steelmaking process similar to Kelly&apos;s. Bessemer made public his invention at the annual meeting of the British Association for the Advancement of Science held at Cheltenham, England, August 1856. As a result of his paper, "On the Manufacture of Malleable Iron and Steel Without Fuel," and his progressive leadership in the years to follow, the process became permanently identified with the name, Bessemer. Credit for the commercial adaptation of the process must be given two additional persons. Robert Mushet (Fig. 3) in 1856 in England recognized the necessity of deoxidation and recarburization of the converter product and evolved the technique for adding high manganese iron following the blow. In Sweden, in July 1858, G_ F. Göranson [ ]

Jan 1, 1961

By S. Stutz

Coal, like most other minerals, only exceptionally occurs in a sufficiently pare state to he directly available for general manufacturing purposes. And even where this is the case, the small coal or slack is usually more impure than the lump coal, as the slate, clay, etc., from the roof and bottom of the vein become mixed with it in the handling it undergoes. These impurities often exceed ten or more per cent. in addition to the impurities of the coal itself. The most common impurities of the coal are slate, or shale, clay, and sulphur. The latter occurs in different forms, but moat frequently as bisulphide of iron, or iron pyrites, and as sulphate of lime, or gypum. In both cases the impnrities add greatly to the amount of ash, and where they are present in considerable quantities the raw coal, and still more the coke made from it, is unfit for the manufacture of iron. Coke will coutain on an average at least fifty per cent. more ash and sulphur than the ram coal from which it is made. To the manufacturer of iron every additional per cent. of ash which his coal or coke contains is a source of additional expense, seemingly small, and yet very important in the aggregate. In the blast-furnace, for instance, the ash must be heated up to the melting-point, and, since it is composed largely of refractory substances, the consumption of carbon in melting it will be equal to at least one-half of its weight; that is, a certain part of tile coke is consumed for the melting and fluxing of the ash and is lost. Besides this, it is well enough known to the iron-master that coke containing lees ash makes the &lag or cinder more liquid and less incliner1 to stick to the walls of the furnace. Fuel containing much sulphur produces generally a white iron, poor in carbon, while from the same ore arrd flux, with a pure fuel, a good foundry iron might be obtained. The work of separating slate, sulphur, etd, from the coal has as yet only been successfully accomplished by the washing process. This process depends for its success on the differences in the specific

Jan 1, 1881

By John Riegle

To date. utility company underground storage of gas has generally been restricted to depleted dry gas fields. The Playa del Rey project is probably the first to successfully store gas in a partially depleted oil reservoir with the recovery of large volumes of pas at high rates as the main objective. Oil recovery has been a secondary consideration. Problems encountered unusual to those of storage in a dry gas zone were: (1) the removal and retardation of formation of emulsion. (2) the upstructure movement of fluid during withdrawal periods which formed fluid blocks, and (3) reservoir shrinkage resulting from encroachment of edgewater. The solution of these problems as outlined in the paper has resulted in increasing the withdrawal rate from the original design capacity of 4,000 Mcf per hour to the current 10.000 Mcf per hour. Additional increase is anticipated as the operations continue. Migration. reservoir performance. operational procedure and a historical record are included to make this a resume of the project from its war-time inception in 1942 to the first of 1952. INTRODUCTION The Playa del Rey underground gas storage project is probably the first project in which gas has been stored in a partially depleted oil reservoir, with the recovery of large volumes of gas at high rates as the main objective and the recovery of oil a secondary consideration. Problems unusual to those of storage in dry gas zones have made this a pioneer endeavor. The total storage capacity of approximately 1,500,000 Mcf of this reservoir is small in comparison with other underground gas storage projects. However. by study and experiment the deliverability into transmission lines. operating at pressures in excess of 150 lbs., has been nearly tripled in the past three years. to the current 10.000 Mcf per hour late, without the use of compression. It is anticipated this rate will gradually increase as additional fluid is removed from the formation. LOCATION AND HISTORY Playa del Key is located on Santa Monica Bay about two miles south of the beach commuity of Venice and 15 miles southwest of the renter of the City city Los Angeles. Fig. 1. The discovery well was completed at 6,194 ft in 1929. An upper zone at 3,905 ft was found on June 18. 1930. Townlot development was very rapid and by the end of 1930 there were 141 producing wells in the field. The Union Oil Co. completed a lower zone well south of the Townlot Field in May, 1931, which was believed to be an extension, until additional drilling of about 50 wells during 1934 and 1935 indicated this area to be a separate accumulation as shown on Fig. 2. The lower oil horizon, which is now the storage zone, had no original gas cap and is believed to be a continental detrital deposit of conglomerate that accumulated in valleys and depressions of a weathered schist high. which later subsided and was overlain by an impervious nodular shale. This type of formation has rapid variation of porosity. permeability and thickness due to lack of sorting action common to marine deposition. and the uneven surface of the original schist high. Production was limited on the upstructure sides by the pinching out of the conglomerate, and downstructure by edgewater. Unrestricted production, together with high permeabilities, led to large wastage of gas from this new area as facilities were not available for transport of gas to market. The decline was very rapid and by 1942 the portion of the new area south of Ballona Creek was nearly depleted. ACQUISITION OF PROPERTY The rapid increase in industrialization of Southern California during World war 11 forced upon the local gas com-

Jan 1, 1953

By Hans-Jürgen Schaller, Horst A. Brodowsky

Activity coefficients of boron in palladium were determined at concentrations up to PdB0.23 by reducing B2O3 between 870" and 1050°C in a controlled H2-H2stream and measuring the resulting weight gain. The deviations from ideal behavior closely resemble those of the system Pd-H and are interpreted in terms of three principles: 1) The solute atoms occupy octahedral interstitial positions. 2) They donate their valence electrons to the 4 d and 5s bands of palladium, raising its Fermi energy. 3) The lattice strain energy is lower for two nearesl -neighbor interstitial particles than for two farther separate ones. SOLID solutions of hydrogen in palladium are a useful subject for studying thermodynamic aspects of the formation of alloys and of nonstoichiometric systems.1-3 The activity of hydrogen is readily measurable to a high degree of accuracy,4&apos;5 even at low temperatures where the deviations from ideal behavior are more pronounced, and its simple structure facilitates an interpretation of these deviations in terms of a detailed model. Two effects are discussed to account for the non-ideal properties:3 An "electronic" effect, connected with the rise of the Fermi energy, as electrons of the interstitial hydrogen atoms enter the electron gas of the metal, and an "elastic" effect, due to an interaction of the regions of strain around each interstitial atom. The electronic effect is based on the idea that the lowest energy levels of the dissolved hydrogen atoms are higher than the Fermi energy, so that the electron will not occupy a localized state but enter into the electron band of the metal.6 The elastic effect is based on the observation that dissolved hydrogen distorts and expands the palladium lattice. The hypothesis is put forward that the elastic strain energy is lower for two adjacent dilatational centers than for two separate ones; i.e., they attract each other. The resulting pair interaction can be used to calculate an elastic contribution to the thermodynamic excess functions by means of one of the statistical methods. This model permitted a detailed description of the solution properties of hydrogen in palladium3 and in palladium alloys.798 An extension of the approach to describe the excess functions of substitutional palladium alloys is possible.9 In order to further test and refine the model, an investigation of other interstitial alloys was started. Palladium dissolves considerable amounts of boron in homogeneous solid solution.10 The palladium lattice expands linearly up to nB = 0.23 (nB = B/Pd atomic ratio), the highest concentration studied." The expan- sion, extrapolated for 1 mole of interstitial per mole of palladium, is 17 pct of the lattice constant of pure palladium vs 5.7 pct in the case of hydrogen.12 The fact that the lattice expands rather than contracts is a strong indication that interstitial positions are occupied. According to neutron diffraction experiments, hydrogen occupies the octahedral sites of the fcc lattice.13 Unfortunately, this direct evidence is not available for the Pb-B system, mainly because of the high-reaction cross section of boron with thermal neutrons. However, by way of analogy and on the grounds of the rather close similarities between the two systems to be reported here, it seems safe to attribute octahedral positions to the dissolved boron, too. At higher boron contents, compounds of stoichiomet-ric compositions are reported such as Pd3B, which has the structure of cementite,14 so that a close structural relationship seems to exist with the system r Fe-C. In their study of hydrogen absorption in Pb-B alloys, Sieverts and Briining noted that alloys with an atomic ratio of about nB = 0.16 are no longer homogeneous15 This observation was confirmed in an extensive X-ray investigation.11,16 The phase boundaries of two miscibility gaps were established. One two-phase region was stable below a transition temperature of about 315°C and extended from nB = 0.015 to 0.178. The other one extended from nB = 0.021 to 0.114 slightly above the transition temperature and had an apex at nB = 0.065 and 410°C. All phases involved have the fcc structure of pure palladium with lattice expansions proportional to their boron contents. The occurrence of miscibility gaps, i.e., the coexistence of dilute and concentrated phases, points to an energy of attraction between the dissolved particles, in the Pb-B system as well as in the Pd-H system. The filling up of the electron bands seems to be analogous, too, in the two systems, as indicated by the hydrogen absorption capacit15,17,18 and by the suscepti bility of Pd-B alloys.l8 In both types of experiments, boron acts as an electron donor. A chemical method was used to measure the activity of boron in palladium. Boron trioxide was reduced in a moist hydrogen stream: B2O3 + 3H2 = 2B + 3H3O [l] At known activities or partial pressures of boron trioxide, hydrogen, and water, the activity of boron could be calculated from the law of mass action. The equilibrium concentration of boron corresponding to this activity was determined as the weight gain of the sample. EXPERIMENTAL The samples consisted of small pieces of foil of 0.1 mm thickness and about 100 mg weight. The palladium was supplied by DEGUSSA, Germany, and stated to be

Jan 1, 1970

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world&apos;s mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because, not more than one or two per cent of the world&apos;s production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By R. M. Daelen

In recent years many new appliances have been introduced into German steel-works and rolling-mills for the purpose of improving working-methods, and of creating and maintaining increased production, and satisfying the ever-growing demand for metal of closely specified hardness, strength and form. One result of the improvements has been to aid very effectively in demonstrating the real superiority of ingot- over wrought-iron for almost every possible purpose, and in dispelling the last vestiges of prejudice unfavorable to the new metal. If, nevertheless, no marked decrease in the number of puddlingfurnaces has yet been noticed, the cause of their survival must be attributed to the greatly increased consumption of all kinds of ironmanufactures. Several large new works for the production of ingotiron are now, however, in course of erection in the Rhenish-Westphalian district, and upon their completion a rapidly diminishing output of wrought-iron may be anticipated. The present aim of all large works manufacturing ingot-iron is to work the molten blast-furnace pig into a finished product without any further fuel-consumption than is required to furnish steam for the rolling-mill. Though practice has established the feasibility of this principle, no works can yet point to its complete adoption, partly because of the limitations imposed by existing conditions and plant, and partly, also, on account of the highly-diversified character of the finished products. The Bessemer-works were the first to feel the influence of the basic process; but of recent years a similar influence has affected the open-hearth, and the owners of works possessing both a converterand an open-hearth plant are now seeking to arrange them for combined working, in charging as well as in casting. In small works the basic-lined reverberatory furnace is constantly gaining ground over the old puddling-furnace. The small basic converter, on the

Jan 1, 1891

By Robert E. Green, T. Hinton

Expressions are derived for tke orientation factors appearing in the Grana to -Lucke theory of dislocation damping, for fcc crystals. The factors are given as functions of the elastic constants, the direction cosines of the specimen axis, atld the direction cosines of the particle displacemeizts, for darnping due to dislocation motion on each of the twelve possible slip systems as ixell as lor simultaneous dislocation rnotion on all twelve systems. RECENTLY Green&apos; has outlined the general procedure for calculation of the modes of wave propagation in a single crystal possessing a given crystallo-graphic orientation. In addition he has suggested how the results of such calculations along with calculations of the resolved shear-stress factors for slip enable the orientation-dependent factors (orientation factors) appearing in the Granato-Lucke theory of dislocation damping to be calculated. However, reen&apos; assumed that the maximum stress on dislocations was in the direction of the particle displacement of the elastic wave giving rise to the dislocation damping. The present cal&apos;culations show that this is an oversimplified approach appropriate only to special cases of high crystallographic symmetry. The exact calculation of stress on the dislocations can only be obtained by resolving the nine components of stress associated with the elastic wave into the appropriate slip direction and then summing. In this paper the general expressions for orientation factors are derived for fcc crystals in terms of the elastic constants, the direction cosines of the particle displacements, and the direction cosines of the specimen axis, bearing in mind the point mentioned above. Equations are presented which give the orientation factors for damping due to dislocation motion on each of the twelve possible slip systems as well as for simultaneous dislocation motion on all twelve systems arising from elastic-wave propagation. These orientation factors are appropriate to attenuation measurements made by the pulse-echo technique, where the elastic wave is a traveling wave. They will be compared with those for the case of a standing wave as derived by Granato and Lucke which are appropriate to measurements of internal friction by the resonance technique. The expressions for the orientation factors are compared with the five values given by insruch,&apos; based on unpublished work of Granato and Liicke, for positions of highest symmetry in the stereographic triangle. The various equations derived for modes of wave propagation and orientation factors have been evaluated for the case of aluminum crystals at 1-deg intervals throughout the stereographic triangle. These results will be presented in the form of contour diagrams in a subsequent paper3 and their relevance to ultrasonic measurements discussed. ORIENTATION FACTORS The coordinate system used for the calculations is shown in Fig. 1 and all specimen axes are taken to lie in the shaded standard triangle. The twelve slip systems are indexed according to Table I. Following the suggestion of lers, we may define the orientation factor Ok in the Granato-Liicke theory5 by the equation

Jan 1, 1967

By Eric J. Jette, Frank Foote

The unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investigations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrewsl. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treatment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900&apos; to 950&apos; C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points to "scatter" badly about any curve that may be drawn to represent them and it is difficult to interpret such results. In spite of this, McKeehan shows that the lattice constant of nickel increased as the iron content increased. His results for the alpha-iron phase are less conclusive. Osawa4 also investigated the entire system. For alloys slowly cooled from 1150&apos; C. and then filed into samples for X-ray analysis, he found

Jan 1, 1936

By Frank Foote, Eric J. Jette

The unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investigations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrewsl. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treatment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900&apos; to 950&apos; C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points to "scatter" badly about any curve that may be drawn to represent them and it is difficult to interpret such results. In spite of this, McKeehan shows that the lattice constant of nickel increased as the iron content increased. His results for the alpha-iron phase are less conclusive. Osawa4 also investigated the entire system. For alloys slowly cooled from 1150&apos; C. and then filed into samples for X-ray analysis, he found

Jan 1, 1936

By S. F. Emmons

" The obscurity which still veils from us the true nature of veins will become more and more cleared up when they can be considered in connection with the geological structure of the regions in which they occur."* These words, according to Lossen, the biographer of the late Dr. A. von Groddeck, of Clausthal, were the last received by him from that eminent man, perhaps the most far-sighted and carefully progressive of recent writers on ore-deposits. They seem to me to form a fitting text for what I am about to say; since I find that many of the conclusions at which I have arrived by my own study of the structural relations of ore-deposits, or, in other words, of the structural and dynamic geology of the regions in which they occur in this country, have been similarly determined by him within recent years in Europe, and especially in his home field of work, the Hartz. I shall not enter upon a detailed account of how far other workers may have arrived at similar conclusions with myself, since these questions of priority are of little interest, except to those immediately concerned; but will briefly present the methods by which, in my work in this country, I have arrived at certain generalizations, and will point out the practical bearing which they may have upon the work of mining engineers. In my first thorough and systematic examination of an important group of ore-deposits, viz., that of Leadville, Colorado, I was enabled, through the generous facilities afforded me by the then Director of the Geological Survey, Mr. Clarence King, to make a most elaborate and detailed study of the geology, not only of the immediate vicinity of the mines, but of the adjacent mountain regions, based upon accurate topographical and underground maps, and

Jan 1, 1888

By David J. Mack

A survey and critical appraisal of published information about Young&apos;s modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young&apos;s modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young&apos;s modulus. CalculatioX oP YouNg&apos;s Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess&apos;enden4&apos;,~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

By A. W. WALKER

All branches of production engineering showed steady and definite progress during 1941. Most of it has been of the slower and more conservative type rather than the sensational. To a large degree the changes have been influenced by the expanding war economy, and this tendency will probably be even more marked during the coming year. The stress of the times is placing more emphasis on the principles of engineering and conservation, with the object of obtaining the greatest possible recovery with a minimum waste or expenditure of equipment. Also available material supplies are often being turned to new uses.

Jan 1, 1942