Search Documents

By E. H. Rose

The present symposium on flotation machines provides a unique opportunity for group reappraisal of standard or habitual viewpoints. A symposium is by definition a trading post- for observations that might prove complementary when put together, thus leading to useful thoughts that might not have been evident from the original observations individually. The present paper, pertaining to power consumption in flotation, is deliberately an experiment of that kind. Data were solicited from the operating superintendents of several of the major flotation plants on this continent. The information received, covering a total of 14 separate operations in seven plants, has been collated in terms of power intensity; that is, the total power input per cubic foot of cell volume. This departs somewhat from the conventional expression of power per ton of ore treated, though the latter figure is also given for the plants concerned. Because of wartime restrictions, particularly in Canada, identifying names of plants and machines are withheld. Not as a firm conclusion, but as a tender for symposium discussion, the following points are made: 1. That flotation is a power operation in much the same sense as ball milling. 2. That contact time is the complement of power intensity and may be decreased as the latter is increased. 3. That a decrease in flotation power per ton of ore can result from an increase in power intensity. Analogy with Grinding In grinding, it has become axiomatic that the more the power put into a given operation, the greater the work performance. The analogous view is now proposed that the effectiveness of any flotation operation will be related to the mechanical energy usefully applied to that operation. Under this view, each increment of properly directed input energy should give either an increase in unit tonnage or an improvement in the metallurgical separation (concentrate grade or tailing grade), until either the theoretical limit imposed by mineral constitution or surface condition is reached, or until further increments of power become uneconomic under the law of diminishing returns. Thus, as in grinding, there are two forms of output that greater power input or improved utilization of power can produce. As for the law of diminishing returns, lower unit cost of power through improved generating efficiency in the past decade has pushed the limit back. Over and above this, however, there is strong indication in the operationg data herein presented that higher power intensity results in an actual economy of over-all power consumption. Like crushing and grinding, flotation accomplishes a rupture of the forces of molecular attraction, by taking particles from the common environment and placing them in the two separate environments of

Jan 1, 1947

By S. F. Radtke, J. A. Snyder, R. M. Scriver

An automatic, continuous casting arc furnace employing a nonconsum-able electrode and a direct current arc has been constructed and operated successfully for titanium. A comparison of the properties of arc and induction-melted titanium indicates that where high ductility, formability, and toughness are required, arc-melted metal is preferable. BECAUSE of the reactivity of titanium metal with all known refractories and the common atmospheric gases, melting of the metal presents numerous problems. It is necessary to provide an inert atmosphere in the furnace as well as a crucible material that will not react with the molten metal, if a ductile ingot is to be produced. Two special furnaces have been developed that meet the requirements and one, the induction heated graphite furnace, has been described in some detail.' Little information is available for sizable units wherein power is applied to the melt through an arc, and the dearth of technical information on such a furnace prompted this report. It has been demonstrated clearly that arc melting produces titanium metal with superior toughness, ductility, and formability. To produce titanium ingots with these properties, an automatic, continuous casting arc furnace has been developed and is described herein. The history of arc melting may be traced to 1800, when Sir Humphrey Davy2 first experimented with Volta's electric battery and found that light could be produced and an arc formed between two carbon points attached to the cell. The discovery of the arc was followed by the design and construction of an arc furnace by Napier," in 1845, for the reduction of metal oxides. In 1853, Pichou' described a similar furnace, although it was not until the discovery of the dynamo in 1867 that the arc furnace could achieve commercial significance. In 1878, Siemens- esigned the first arc furnace intended for the melting of metals and by 1882 had melted steel and platinum successfully. . This was followed by Moissan's" classical work with the arc furnace in 1892. W. von Bolton,' in 1905, found that the arc furnace was suited admirably for melting refractory metals. In his work with tantalum, no suitable refractories for retaining the molten metal were found to exist. Together with Otto Simpson, he developed an arc furnace with a water-cooled copper crucible in which tantalum could be melted without contamination. This technique proved eminently successful. In his paper on the preparation of ductile titanium, Krolle first described an application of the von Bolton furnace to the melting of this metal. The

Jan 1, 1952

By E. H. Rose

The present symposium on flotation machines provides a unique opportunity for group reappraisal of standard or habitual viewpoints. A symposium is by definition a trading post- for observations that might prove complementary when put together, thus leading to useful thoughts that might not have been evident from the original observations individually. The present paper, pertaining to power consumption in flotation, is deliberately an experiment of that kind. Data were solicited from the operating superintendents of several of the major flotation plants on this continent. The information received, covering a total of 14 separate operations in seven plants, has been collated in terms of power intensity; that is, the total power input per cubic foot of cell volume. This departs somewhat from the conventional expression of power per ton of ore treated, though the latter figure is also given for the plants concerned. Because of wartime restrictions, particularly in Canada, identifying names of plants and machines are withheld. Not as a firm conclusion, but as a tender for symposium discussion, the following points are made: 1. That flotation is a power operation in much the same sense as ball milling. 2. That contact time is the complement of power intensity and may be decreased as the latter is increased. 3. That a decrease in flotation power per ton of ore can result from an increase in power intensity. Analogy with Grinding In grinding, it has become axiomatic that the more the power put into a given operation, the greater the work performance. The analogous view is now proposed that the effectiveness of any flotation operation will be related to the mechanical energy usefully applied to that operation. Under this view, each increment of properly directed input energy should give either an increase in unit tonnage or an improvement in the metallurgical separation (concentrate grade or tailing grade), until either the theoretical limit imposed by mineral constitution or surface condition is reached, or until further increments of power become uneconomic under the law of diminishing returns. Thus, as in grinding, there are two forms of output that greater power input or improved utilization of power can produce. As for the law of diminishing returns, lower unit cost of power through improved generating efficiency in the past decade has pushed the limit back. Over and above this, however, there is strong indication in the operationg data herein presented that higher power intensity results in an actual economy of over-all power consumption. Like crushing and grinding, flotation accomplishes a rupture of the forces of molecular attraction, by taking particles from the common environment and placing them in the two separate environments of

Jan 1, 1947

By John Norton

FOR many years the copper-bearing steels have been of considerable interest to the metallurgist because of their corrosion-resistant properties. More recently the discovery of their definite age-hardening characteristics has focused attention on them again. In a recent paper, Smith and Palmer(1)? have given an admirable description of the behavior of a considerable number of steels of this type and a study of their results suggests two questions, of a more or less fundamental sort. In the first place, it has been plainly shown that the hardening effect of added copper does not increase up to the maximum solubility of copper in iron as given by earlier investigators, but reaches its greatest value considerably below this point. This fact suggests that either the solubil-ity is not, so great as previous investigators have stated, or that the age-hardening mechanism is not the simple precipitation phenomenon that has been postulated. In the second place, the nature of the aging mechanism in this partic-ular system should be determined. Recent developments in the study of age-hardening processes have shown that the increase of hardness is often, but not always, accompanied by precipitation and the action of a particular system is not predictable on the basis of its components or type of phase diagram. It would be of considerable interest to study the aging of the iron-rich iron-copper alloys in detail. One would like to know whether the aging mechanism is different at high and low aging tempera-tures, and whether the extreme sluggishness of the system may perhaps represent some new type of aging process.

Jan 1, 1934

By Charles J. Haas

The resistance which rock bolts offer to shear movements along fracture planes and bedding planes near a mine opening has been suggested as one of the mechanisms by which bolts contribute to the support of weak rock in the roof or sidewall. That such displacements do occur is a fact fairly well known. Inspections of drill holes that have been drilled for some time often reveal that the holes have been offset at one or more points some time after drilling. Resin grouted bolts are often cited as being better able to resist shear movement in the roof because the annulus around the steel bar is filled with grout, whereas the sides of a conventional bolt will not contact the rock until a rather large shear displacement has occurred. When this project began, there were no experimental data to support or refute the above arguments. A laboratory shear test program was, therefore, devised to evaluate the effectiveness of various types of bolts in resisting shear under various conditions which exist in situ. Research reported earlier (Haas, 1976) included a theoretical analysis of a conventional bolt intersecting a shear surface, and experimental data on the shear resistance of smooth (lapped) shear surfaces, intersected at various angles by conventional and resin grouted bolts. The present paper extends the previous analysis to consider the effect of the initial roughness of the shear surface. Joint roughness is a particularly significant factor since undulations of the shear surface cause dilatation of the joint, which in turn, causes high tensile loading of a bolt intersecting the joint.

Jan 1, 1982

By C. Laird, C. E. Feltner

An investigation into the effect of a material's slip character on its high strain fatigue properties has been carried out using copper and Cu-7.5 wt pct A1 as representative wavy and planar slip mode materials, respectively. In copper, the constant term and exponent in the Coffin-Manson equation, ?EpNf1/2 = const, are unaffected by the temperature of testing or the history of the metal. On the other hand, in Cu-7.5 wl pcl Al, while the exponent is invariant, the constant is increased with respect to copper and increased further with decrease in temperature. The life in Cu-7.5 wt pct A1 is double that of copper at room temperature and about four times at 78°K. Fractoflaphic studies indicate that these diffevences in life are associated with the early stages of cracking. In copper, severe surface rumpling provides crack nuclei at pain boundaries independent of' testing temperature or the history of the metal. In Cu-7.5 wt pct Al, the planar slip mode of deformation prevents grain boundary folding; crack nucleation is therefore mainly transgranular and the increase in life with respect to copper is associated with a prolonged linking-up stage of such transgranulay cracks. At the lower temperature the increased difficulty of cross slip inhibits multiplication of trans-granular cracks and retards the linking-up process, giving a further enhaancement in life. It is expected that such behavior will be found general in materials of wavy and planar slip mode, respectively. STAGE II crack propagation in high strain fatigue takes place by a repetitive process of crack tip blunting in the tension part of a fatigue cycle followed by resharpening of the crack in the compression part.1-3 This mechanism has come to be called the "plastic relaxation process".3 At very high strains (lives to failure less than 103 cycles), most of the life of a specimen is spent in crack propagation by the plastic relaxation process.4,5 Since the differences in the cyclic strain hardening behavior of metals and alloys are comparatively small in this strain range,6,7 the amount of blunting at a crack tip depends primarily on the applied strain amplitude. The rate of crack propagation in this life range is therefore nearly constant with respect to material and temperature of testing. In the longer life portion of the high strain fatigue range (l03 to 103 cycles to failure), a considerable fraction of the lives is spent in crack initiation and Stage I growth. Grain boundaries have frequently4,5,8 been found to be the sites for this growth which is also associated with a surface folding process.4'5 Such folding behavior may also be general in any material having a grain structure and capable of plastic deformation. It has therefore been suggested475 that the universality of the Coff in-Manson law,9'10 constant,* where ?Ep is the plastic strain range and Nf the number of cycles to failure, is reflected in the approximate invariance of both the crack initiation and propagation behavior. It happens that, in most investigations of the phenomena associated with failure,4,5,8 materials with a wavy slip mode have been used as vehicles for the studies, or else "normally" planar slip mode materials have been tested under conditions giving rise to wavy glide deformation, e.g., stainless steels cycled at high temperature.'' The purpose of the present investigation was to determine whether or not different cracking phenomena would occur when the slip mode of a material is planar and if the associated life to failure would be different than that of a wavy slip

Jan 1, 1968

By E. K. Soper

Introduction It has been observed that where veins or other types of orebodies are intersected by cross faults, the continuation of the ore deposit below the fault is often of lower grade than that portion above the dislocation.1 In some mines, the reverse of these conditions has been noted, and the richest ore is found to occur in that portion of the vein beneath the fault intersection. Such instances seem to be less frequent than those where the richest ore is above the offset. The important and widespread influence of fault and vein intersections upon the localization of ore shoots is well known 2 but the factors that govern the position of the ore shoot relative to the fault intersection seem to be less clearly understood. The richest ore may be above or below the fault,. or it may occur at-the point of intersection, or there may be no change. Recent observations made by the writer in mines in Idaho and Montana suggested a possible explanation for the changes in the richness of ore below certain types of fault intersections. These observations have been supplemented by a study of the literature containing detailed descriptions of ore deposits at a large number of mines in North America. The results of these studies are presented herewith in the hope that they may lead to further discussion of this important phase of ore deposition.

Jan 10, 1917

CHAIRMAN (J . E. JOHNSON, J R., New York, N. Y.).-It may be n matter of some interest that sodium cyanide is now being made commercially by melting together in an electric furnace calcium cyanide with a common salt, which produces calcium chloride and sodium cyanide. It seems to me entirely possible that you have here about the same results that would be obtained by melting calcium chloride and ordinary cyanide together, only you obtain it a good deal cheaper. There is no doubt about that reaction once it is being carried on on a large industrial scale for the manufacture of cyanide for other uses. I think probably the same, thing takes place here, with the possible exception of lowering the melting point due to the presence of the calcium chloride.

Jan 5, 1919

By A. M. Mirani

The Mine Planning System consists of two parts: 1. A Sales Forecast (Sales Planning) 2. A Production Planning. The mathematical methods of the sales forecast are the exponential smoothing and a method with Markov-Chains. By these methods the quantity of material (ore, coal) will be calculated for the time planned. These quantities constitute the points in the production-planning. In the production-planning , special kinds of networks are used for calculating the resources-equipment required, labor and costs. A special routine optimizes the sequence of the mining areas within the mine on the basis of the lowest costs. The resources can be limited. The activities will be shifted when the demand exceeds this limit. The basis of the production-planning are computer files, in which the geological data and economical evaluations are stored.

Jan 1, 1969

By T. M. Drown, P. W. Shimer

The precipitation of phosphoric with titanic acid, by boiling an iron solution which had been reduced to the ferrous condition by sulpharetted hydrogen or sulphurous acid, was first noticed by E. H. Bogardus in 1874.* Since that time, as far as we are aware, not much has been published on the relation of these two acids to each other, and to silicic acid, in the ordinary course of analysis of iron ores. The following investigation may perhaps aid in clewing up some of the obscure points in the analysis of titaniferous ores. THE DETERMINATION OF PHOSPHORUS. From two to five grams of the finely powdered ore are weighed into a beaker and treated with about 50 c.c. of hydrochloric acid (sp. gr. 1.12), evaporated to dryness, and heated ih an air-bath for

Jan 1, 1882

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By William B. Stephenson

IN the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. BASIC REQUIREMENTS To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,1 who says, among his conclusions: " ... values of ƒ (friction factor) .. . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. MAINTAINING CONSTANT VOLUME Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping system. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1946

By H. Conrad Meyer

The wizardry of nucleonics has added new and greater dimensions to the almost inseparable "twins"-zirconium and hafnium. So close is their relationship that neither element is found free of the other in any presently known mineral. Although zirconium in the form of its oxide was discovered in 1789 by Klaproth, the metal in an impure, nonductile form was not isolated until 1824 by Berzelius. About 100 years later -1925-van Arkel and deBoer developed and patented a technique for the deposition in vacuo of crystalline, coherent, highly ductile metal of extreme purity on an electrically heated filament through the dissociation of gaseous zirconium tetraiodide. Within the past five years both zirconium and hafnium have been dramatized by the press and in popular science magazines. This has led to the false assumption that practically all of the world consumption of zirconium ores is used in the production of the metals. Recent statistics on the subject show that not over 15 pct of the zirconium ore consumed in 1958 went to ferrosilicon zirconium and zirconium metal. The rest was consumed in refractories, foundry sand and facings and ceramics. The importance of zirconium as a component in compact, relatively lightweight nuclear energy units, such as those now used in the submarine Nautilus,6 is well established. A rival of zirconium metal as a casing for atomic fuels is a newly developed ceramic body. It is claimed to be cheaper than zirconium-to withstand higher temperatures-and to be more resistant to corrosion. Whether such ceramic casings have the required low thermal neutron absorption cross section, high strength and easy formability of zirconium is yet to be demonstrated. Hafnium, because of its low order of abundance and its close chemical relationship to zirconium, was not definitely recognized as a new element until around 1923, despite prior claims. A study of the X-ray spectra of zirconium led to its identification. The circumstances leading to the discovery of hafnium were much less fortuitous than those surrounding zirconium. The more precise tools of arc and X-ray spectrometry lent themselves admirably to the search for elements to fill certain gaps in the periodic table. [ ] Pure, ductile hafnium-a metal similar in appearance to stainless steel-has a specific gravity of 13.3 (zirconium 6.52) and a melting point of 2,200°C. In other respects it closely resembles zirconium except in one important respect which gives it a preeminent position in nuclear energy development, namely, a high thermal-neutron absorption cross section. This explains the necessity of hafnium-free zirconium in atomic piles. The ability of hafnium to capture thermal neutrons makes it an excellent "moderator" of "governor" when used as control rods in nuclear reactors (Table 1).

Jan 1, 1960

By W. J. Taylor

FURNACE-MEN who have not taken advantage of the use of dynamite in certain blast-furnace troubles, as explained by Mr. Witherbee in his valuable papers read before the Institute some years since, cannot appreciate the quick relief and great advantage that may be derived at times from its judicious employment. Before giving my experience in the use of high explosives in blastfurnace troubles of certain kinds, I will record a method I have used with marked success in " blowing down." Had I not understood, however, the use of powder, I would have " salamandered " effectually the first time I tried it. Early in my straight-furnace experiments, last summer, at the Chester, N. J., Furnace, I wanted to blow down to within 3 or 4 feet of the tuyeres. To do this with a down-comer not lined, and without putting in any limestone to keep the gases cool enough to do no harm, was not an easy task. We could keep the bell and hopper cool by filling them with water, say 12 inches deep; but before we got the stock down 15 or 20 feet the pyrometer in the gas-flue on top mas up to 1300°, and the clowncomer was red-hot, with the heat still rising. In this emergency my assistant, Mr. N. M. Langdon, urged the trial of a plan lie had often advocated, viz., the introduction of water in some way under the bell in the proper quantity, in order that its evaporation might absorb and reduce the heat of the escaping gases to a point where it would not do any harm. He thought the bell

Jan 1, 1885

By A. STEPHENSON

EXPERIMENTAL work conducted at the Petroleum Engineering Laboratory of the University of California by L. C. Uren, J. Domercq, Jr., and J. Mejia has shown that small diameter wells offer tremendous resistance to the flow of fluids in their immediate vicinity. This resistance is due in part to the constriction of the area through which the fluids must pass as they approach the wall of the well, but is also accentuated by the increased volume which results from gas expansion. The latter in turn is a function of the deduction in pressure, the fundamental cause of fluid movement. If the diameter of the bore is enlarged several diameters, the capacity of the well, or the volume of fluid passing per unit drop in pressure per unit of time, is greatly increased without necessitating such high fluid velocities. The fundamental features which should be taken into consideration in the design of casing joints were stressed by J. B. Graham and E. E. Smith. These involved such points as correct thread design, high efficiency, and small diameter, together with the insurance that leakage will absolutely be prevented. The practical features of such design were ably discussed by engineers from leading steel manufacturers.

Jan 1, 1935

By G. A. Vissac

In the presentation which follows, wash-ability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. Float-and-sink Tests For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve"—a somewhat misleading term—will be considered; Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. New Form of Graphic Presentation The resemblance of the recovery curve ill Fig. 1, or, for that matter, the recovery curve obtained in common practice! to a Power curve is apparent. The general equation of such a curve is Y = axn, where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis! the recovery graph will be a straight line, using the same variables as in Fig. I; namely, the ash con-

Jan 1, 1942

By G. A. Vissac

In the presentation which follows, wash-ability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. Float-and-sink Tests For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve"—a somewhat misleading term—will be considered; Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. New Form of Graphic Presentation The resemblance of the recovery curve ill Fig. 1, or, for that matter, the recovery curve obtained in common practice! to a Power curve is apparent. The general equation of such a curve is Y = axn, where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis! the recovery graph will be a straight line, using the same variables as in Fig. I; namely, the ash con-

Jan 1, 1942

By H. W. Hitzrot, R. A. Limons, L. V. Fegan

The authors have developed and tested a new method for measuring pellet-bed temperatures in the traveling-grate or the shaft furnace. This method-using silver-palladium alloy wires as indicators-is less costly and less time-consuming than existing methods. Silver palladium wires, having specific melting points in the 2000° to 2500°F range, are enclosed in ceramic capsules. Each capsule is placed in a nichrome wire basket filled with a sample of green pellets, the baskets being the means for recovering the capsule after firing. After the encapsulated wires have been exposed to the firing cycle, the alloy wires are examined to determine the maximum temperatures attained by the pellet sample. This gives accurate, rapid determinations of maximum temperatures attained during pellet induration in either the traveling-grate or shaft furnace.

Jan 6, 1965

By F. H. Ellinger

TI HE crystal structure of neodymium has been re-A ported by Quill1 and by Klemm and Bommer"s to be hexagonal-close-packed, Strukturbericht-type A3, with a, = 3.650.4, c, = 5.890.4, c/a = 1.614. Klemm and Bommer,% owever, pointed out that the observed intensities of the lines of the neodymium powder pattern agreed only in part with the intensities calculated for the type A3 structure, and that the neodymium powder pattern showed extra lines which could not be traced to impurities. They found that these extra lines could be accounted for by doubling the c-axis, but apparently they did not consider their evidence to be sufficiently conclusive to justify reporting the doubled c-axis. In the present work, the structure of neodymium was found to be double hexagonal-close-packed. The neodymium metal used in the present investigation was obtained through the courtesy of F. H. Spedding of the Ames Laboratory. Its major impurity was stated to be 0.03 pct Ca. The author's spectrographic analysis indicated high purity and carbon was determined to be less than 30 ppm. X-ray powder specimens were prepared from filings stress relieved in vacuum at 200°C for 50 hr. Powder photographs were taken in an 114.6 mm diam camera (Straumanis film mounting) at room temperature and in a 19 cm diam Unicam high temperature camera at elevated temperatures. Copper x-radia-tion was used for all the photographs. The powder pattern of neodymium was found to index to a hexagonal unit cell with dimensions, as determined from the high angle Ka doublets, of: a.= 3.655+0.001.4; c, = 11.796+0.004.4; and c/a = 3.227 at room temperature. The measured density of neodymium shows that this cell contains 4 atoms, the calculated density is accordingly D, = 7.02 g per cu cm. The diffraction data for the first 15 lines of the powder pattern are listed in Table I. In a double hexagonal-close-packed unit cell, the 4 atoms would be in the positions (0,0,0), (0,0,%), (1/3, 2/3, 1/4), and (2/3,1/3,%) of space group P 6,/mmc. On the basis of these positions, the relative intensities of the reflections were calculated using the expression: 1+cos2 20 I oc \Frp 1 ' sin2 0 cos 0 where F is the structure factor and p is the multi- plicity factor. Since absorption was not taken into consideration, comparison of observed and calculated intensities should be made only for neighboring reflections. Each atom has 12 neighbors, 6 in the basal plane at a distance of 3.655.4 and 3 above and 3 below at the closer distance of 3.626.4. These distances correspond to an average radius of the neodymium atom of 1.820.4. The description of this structure in terms of A, B, and C close-packed layers of atoms is ABAC ABAC. ...... The structure repeats every fourth layer and the stacking sequence of the second, third, and fourth layers corresponds to cubic-close-packing of atoms. A series of powder photographs taken at successively increasing temperatures up to 680a10"C revealed that the double hexagonal-close-packed structure is stable up to this temperature. Acknowledgments The authw wishes to thank W. H. Zachariasen and A. S. Coffinberry for their helpful comments on this work and also Marion Gibbs for measuring the diffraction films. This work was sponsored by the United States Atomic Energy Commission.

Jan 1, 1956

By John H. Smith, Michael B. Bever

Pure gold was deformed by wire drawing at room temperature and 78°K. After deformation at room temperature, the stored energy and the resistivity increment reached nearly constant levels at high strains, whereas the yield stress continued to increase with strain. After deformation at 78K, the stored energy, the reszstivity increment, and the yield stress were larger than after deformation at room temperature mzd increased continuously with strain. Annealing at THE stored energy and the changes in properties resulting from cold working of Au-Ag alloys by various processes have been the subject of a series of investigations in this laboratory.'-' The work reported here room temperature after deformation at 78°K did not affect the yield stress appreciably. The stored energy, resistivity increment, and Lncrease in yield stress after deformation at room te-lnperature can be explained primarily in lerrns of dislocations while point defects, as well as dislocations, contribute to the changes in these properties after deformalion at 78°K. extends this research to pure gold. The stored energy, the resistivity increment, and the tensile properties after deformation by wire drawing were measured as functions of the strain at room temperature and at 78°K. The effect of the testing temperature and the effect of intermediate annealing at room temperature before testing at 78°K on the tensile properties of gold deformed at 78°K were also investigated. wire drawing made it possible to use a large range of strains, which was desirable because previous work on the deformation of gold had been carried out mainly at relatively small strains.'-l2 Also, wire specimens

Jan 1, 1969