Search Documents

By N TassT, J Cyr

At the East Sullivan site, wood wastes covering the abandoned mine tailings impoundment prevent sulfide oxidation by creating an anoxic environment. The addition of coarse ligneous wastes and their high permeability favour infiltration, resulting in a water table rise that maintains most tailings under water saturation and thus provides an additional protection against sulfide oxidation. Moreover, high infiltration allows a more rapid flushing of acid prone groundwater generated prior to the cover placement, which could cause acid mine drainage over a long period of time. Finally, the pore-waters under the cover are characterised by a strong reducing potential, high alkalinity, and near neutral pHs. These conditions favour sulfate reduction and base metal precipitation as sulfides and as carbonates. Pore-water composition monitored from 1992 to 1998 showed a significant Fe2+ decrease, following cover placement. Thereafter, the restoration strategy capitalised on the alkaline and reductive properties of the waters underlying the wood-waste cover. An original treatment of acid effluents, based on the recirculation of water discharging around the impoundment through the organic cover, was implemented. In 2002, the recirculated water from May to October had a mean pumping rate of 240 m3/h, for a total volume of 800 000 m3. Data gathered near the dispersal zone from 2000 to 2002 show that despite the recirculation of acid water (pH ÿ3), the pH decreases by only one unit from 7 to 6, during the recirculation period, ie from May to November. However, alkalinity decreases from 800 to 100 mg/L-CaCO3. Despite this decrease, the alkalinity is back up to 800 mg/L-CaCO3 the following May, thanks to sulfate reduction. From 2000 to 2002, Fe2+ concentration in the pore waters near the dispersal zone is maintained below 2 mg/L. Evolution of surface water quality suggests that the contaminated groundwater flush is completed in the north and north-west area of the impoundment; the east sector is under recovery, while the south sector remains the most problematic. A wood-waste cover, besides limiting sulfide oxidation, can fill the role of alkaline reducing barrier for the treatment of these acidogenic waters, until a balance between acidity and alkalinity in the effluent is reached.

Jan 1, 2003

Cominco Ltd's Polaris Mine in Canada's High Arctic has been successfully mining zinc ore in permafrost since 1981. Mining methods using frozen backfill have been the key to success. The mine is now producing about 60 per cent of the ore from pillars while maintaining high productivities. Annual ore production is just over one million tonnes providing more than 200 000 tonnes of zinc concentrate each year. Cominco Ltd has adapted management and operating practices to suit the harsh environment and the isolated site, and has shown that a profitable development can be carried out in the tough Arctic conditions, with minimum impact on the environment.

Jan 1, 1993

By Houtgraaf M

The Far Fanning gold deposit is situated 60 kilometres south-west of Townsville (Fig. 1). Previous recorded production is 3756 tonnes returning about 1600 ounces of gold. This has been taken from surface and shallow underground workings- scattered over the strike length of the deposit of 1700 metres. The main production period was from 1895 to 1908.Previous exploration involving extensive trenching and sampling has been: carried out intermittently. since the 1930's, by Gold Mines of Australia (1932), Placer (1974), Anaconda (1975), Marathon (1980-8-1), Aberfoyle (1981-82), and The Northern Queensland Company (NQC) (1983-present).In 1980 Marathon undertook an extensive drilling programme to test the oxidised mineralisation. Over 200 percussion holes and- 7 diamond holes were drilled along traverse lines spaced 29 to 103 metres apart covering a strike length of around 1800 metres.

Jan 1, 1986

A number of cooperative studies have been carried out as preliminary work for drafting a standard for application of granulated slag sand for concrete, and the following conclusions were reached 1 The ten kinds of granulated slag sands pro- duced in Japan satisfy the national standard for fine aggregate in terms of physical and chemical properties. 2 Mortar and concrete tests conducted with granulated slag sand revealed that, although with slight differences in the extent, gran- ulated slag sands used in these tests were applicable'as fine aggregate for concrete, 3 The pumpability test by a concrete pump carried out on concrete with two kinds of now commercially available granulated slag sand demonstrated that the pump pressure feeding is applicable in the same manner as in the case of ordinary concrete. These tests permitted' preparation of a draft standard for application of granulated slag sand, and the results formed the first step toward utilizing this material as a sub- stitute for natural sand.

Jan 1, 1979

The cost of constantly extending a decline tunnel that plays a part in the actual extractive process is a revenue cost. The characteristics of such a decline tunnel are that it is dug in a series of relatively small excavations. It follows the ore body and is dug as close to the ore body as practicable. In addition, the decline allows for the extraction of ore in the immediate vicinity, with the ore being extracted in a relatively short period of time.

Jan 1, 1990

Australasian mining companies expect a high standard of professionalism from their metals exploration teams. They also have, increasingly, a global perspective, employing explorationists of diverse cultural backgrounds and operating in diverse environments. Human resource development (HRD) of these professional explorationists needs to address all personal facets of functioning independently and interdependently in a modem working culture, as well as the needed technical competency. Creation of a learning organisation to promote this development is critical. Organisational consultants can support managers and supervisors as mentors facing the wide spectrum of development required by the explorationists; mentorship and guidance counselling can then complement training in the maturing of professionals from technical competence to professional independence and interdependence. Empowerment and clearly stated expectations are keys by which professionals can learn efficiently and effectively.

Jan 1, 1996

By G Chitombo, M Ruest

In surface mining, studies of the kinematics of blasted rocks using high speed film/video image analysis have allowed the estimation of the starting time, direction and magnitude of visible movement of fixed sections of the free face. Horizontal displacement versus time plots from discrete targets at the face generally report changes in slope over very small time intervals. These changes indicate step increases in velocity due to the action of explosive gases. In practice, the onset of rock mass movement, different to localised spalling, has been associated with a response time which exceeds the combined times of detonation, propagation and reflection of stress waves. This time is referred to as minimum response or burden movement time. As an engineering index, burden movement time has been used to provide guidelines for the selection of inter-hole and inter-row delay sequences in production blasting. With respect to improving breakage and fragmentation, it has been demonstrated that the delay interval between adjacent explosive charges should be less than the expected burden movement time. Similarly to reduce confinement between rows, delay intervals should exceed the expected burden movement time. The Hybrid Stress Blasting Model (HSBM) is a modelling framework that dynamically links an ideal and non-ideal explosives detonation code to a geomechanical rock model. This blast simulation tool is aimed at analysing the role played by different explosive formulations in fragmenting and/or damaging various rock types under different degrees of confinement. In the current framework, the rock behaviour under extremely high pressures and loading rates is calibrated from shock tests and the role of the explosive in fracture growth is accounted for and assumes a compressible fluid flowing through the explicit fracture network. The model is being developed as part of an international collaborative research project funded by a consortium of companies comprised of explosive and equipment suppliers and major mining houses. As part of the development and validation of the HSBM project, data from literature addressing the kinematics of the rock mass (ie burden displacement, face velocities and response times) has been collated and used to evaluate the current version of the code. A series of numerical experiments have been conducted with the view to: evaluate the response of the rock mass to changes in burden distance given by the impact of both stress waves and radial gas flow pressure;compare the modelling outcomes in terms of displacement, response time and face velocities to documented field observations; andcompare stress induced and stress/gas induced modes in terms of burden displacement outcomes. Results from these experiments have shown that in its current form the model is able to capture the trends observed and measured in practice. This is with respect to the simulation of burden displacement, response time and average face velocities for different geometries and charging conditions. The experiments have served as consistency checks which form part of an ongoing and comprehensive evaluation and validation of the HSBM code also aimed at addressing some of its current limitations.

Jan 1, 2007

The importance of good winding rope practice is stressed. Details of the ropes used for various duties in the four shafts of The Zinc Corporation, Limited (ZC) and New Broken Hill Consolidated Limited (NBHC) are given. Inspection, testing (including non destructive methods), maintenance and rope discard criteria are discussed. There are sane catments about rope installation methods and an appendix is included which outlines the appropriate statutory requirements for winding ropes in New South Wales (NSW).

Jan 1, 1983

In engineering applications of explosives for rock breaking, the released energy is expended mainly into heat, rock crushing and fracturing, seismic waves, air blast, and noise. Those parts of energy which pass into seismic waves and air wave create environmental problems since they are transmitted away from the blast site. In order to predict the environmental effects accurately, one must be able to predict the energy distribution at the source. The energy distribution at the source is significantly controlled by the blast constriction. Consequently, the accuracy of prediction and control of ground vibrations generated by blasting is affected by various matrices of blasting constriction.

Jan 1, 1986

By Collins D. N

The Olympic Dam Copper Smelter Acid Plant is a hybrid plant capable of producing sulphuric acid from either sulphur burning, metallurgical gases or a combination of both. Commissioning of the Acid Plant on sulphur burning commenced in early April 1988 and commissioning on combined sulphur burning and metallurgical gas commenced in August 1988. During commissioning on sulphur burning a number of acid spills occurred due to balancing of tower flows and control of acid dilution. A number of other significant problems were encountered including failure of boiler gaskets, failure of strong acid pumps seals, the fracture of the teflon dilution water injector and the subsequent failing of the acid circulation pump, tank steel failures and various instrumentation problems. The Commissioning of the Acid Plant on metallurgical gases commenced in August and with the exception of the production of oleum in the boiler economizer was relatively trouble free. Oxygen Plant commissioning commenced in May 1988 and was without significant incident. An outline of the basic equipment for the Acid Plant and Oxygen Plant is presented together with aspects associated with the commisisoning of both plants.

Jan 1, 1989

By Schommarz KH, Dunne RC, Goodall CM

Column cells are widely used today for the recovery of base metals by flotation. Their use for the flotation of iron sulphides has not been as rapid. Australia has pioneered the use of large rougher flotation columns. During the last six years, seven rougher columns have been installed on gold mines treating iron sulphides and the technical viability of this technology has been demonstrated. Laboratory column testwork on a gold bearing iron sulphide ore demonstrated the effects of both physical and chemical parameters. In general the large commercial columns operate over a broad range of conditions depending on the downstream treatment of the flotation concentrate. The addition of wash water to commercial columns is not universally applied and there appears to be a need for a better wash water System.

Jan 1, 1993

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

Porphyry type mineralization of Lower Cretaceous age in eastern Queensland has been recognized only from the easternmost part of the northern New England Orogen (Day, Murray and Whitaker, 1978), within the northern Yarrol Province (Horton,1982). Recent work about the Mt. Suthers (Pb, Zn, Ag, Cu, Au), Lug-e-nor (Cu, Pb, Zn, Ag, Au, Mo), and German Tully (Cu, Au, Bi) prospects suggest that there has been a phase of porphyry type mineralization within the Gympie Province, of Lower Cretaceous age, overprinting earlier Permo-Triassic phases. About the Mt. Suthers Prospect surface samples of shallow, medium to heavy textured soils derived from marine sedimentary rocks of Permian age, and extrusive and intrusive igneous rocks of intermediate composition and Triassic age, were analysed for Cu, Zn, Pb, Co, Cr, Ni, Fe, V, Mn and Ag. Whereas strong iithological control determined the distribu- tion of Cu (diorite) and of Cr, Ni, Fe and V ,sedimentary rocks), the distribution of Pb, Zn, Ag and of Cu, were determined by mineralization of faults by a cavity fill hydrothermal process. Gold is associated with the Pb, Zn, Ag mineralization. Co and Mn showed distributions independent of lithology and structure. The fault controlled style of mineraliz- ation at Mt. Suthers is repeated at other localities to the south; Calgoa, Marodian, and German Gully. Relative dating of structural features and isotopic dating of nornblende porphyrites (134-135 m.y.) near and related to those mineralized at German c;ully suggest a previously unrecognized phase of porphyry copper style mineralization in south-east Queensland of Lower Cretaceous age (Fig. 1).

Jan 1, 1987

By Lu S, Jiang Y

The conventional transportation system in open pit, a to u.* itc:,~> truck., to carry the ore along the ramps. Normally, the transportation distance increases greatly as mining progresses deeper. A new approach to overcome the above disadvantage is to adopt a buried roadway by which ores is transported by conveyors from the mining area to the outside dump in the shortest distance so that the production efficiency is greatly increased. Maintenance of the buried roadway in a good working condition is the key factor that determines the success or failure of the proposed approach. This includes the determination of support load, types and structures of support and other related supporting measures. The crucial problem here is to effectively control the load applied on the buried roadway in a certain range that the ordinary support can stand. Based on the theoretical analysis, numerical modelling and physical simulation testing using equivalent material, this paper studies effects on control of the support load by adopting certain measures, for instance reinforcing the surrounding rock and placing the extendable layer between the support and a rock mass. Furthermore, the influence of the dynamic load induced by the movement of heavy vehicles on the stability of the buried roadway is also investigated.

Jan 1, 1995

By Mallett CW, Rynn JMW, Hammond RH

Geological studies and satellite imagery of the Bowen Basin in Central Queensland, Northeastern Australia, have shown that the significant structural controls are a series of major North East/South West (NE/SW) trending structures, which can be traced as lineaments on Advanced Very High Resolution Radiometer (NOAA-AVHRR) imagery as well as on both Landsat Multi-Spectral Scanner (MSS) and Thematic Mapper (TM) imagery. These linea- ments can be traced offshore and into the Coral Sea by the distribution of offshore reefs and the bathymetery of the Queensland Shelf and the Queensland and Marion Plateaus. The seismic activity in Eastern Queensland seems to be divided into two distinct provinces separated by a seismically quiet area. This apparent seismically quiet area is bounded by two of the large lineaments seen on the satellite imagery. These features could be related to the deep crustal structure of Eastern Queensland and to the opening of the Coral Sea.

Jan 1, 1987

By Felice J. J

The assessment of the face velocity of blasts is important in the analysis and subsequent improvement of blast performance. POWERWAVE RADAR is a new tool which will make the collection of this data easier for blast researchers. The data collection technique ensures that a large amount of face velocity data is collected from a blast, and describes the velocity characteristics of the face at a new level of detail. This results in a greater understanding of the effect of drilling and blasting parameters on blast performance. Several case studies are presented which illustrate the collection technique, the type of data generated and how the data is used.

Jan 1, 1992

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

A study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fel_xS, CuFeS2, Cu2S) has been conducted using a mesophilic strain of T. 6ejtAooLcdcth4. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate ion has been monitored. Partially oxidised sulphide substrates have been characterised at regular time intervals by X-ray diffraction methods and extra-cellular organic compounds reporting into leach solution have been identified by'thin layer chromatography. The results indicate that the S¦/SO4 2 partitioning of the sulphide substrates is independent of cell inoculum size and initial pulp density and varies with solution pH, Eh, leaching time and mineralogical properties of the individual sulphide minerals. The signifi- cance of results for applications in selective flotation, coal desulphurisation and agglomera- tion has been outlined.

Jan 1, 1984

By J R. Kyle

The Deep Mill Level Zone (DMLZ) skarn Cu-Au deposit is the deepest explored part of the Ertsberg East Skarn System extending from the surface at 4200 m elevation to the DMLZ at 2900 to 2600 m. The DMLZ is hosted in an upper Cretaceous to lower Tertiary siliciclastic and carbonate succession adjacent to the 3 Ma Ertsberg pluton. Much of the DMLZ ore is hosted by mixed assemblages of siliciclastic and dolomitised carbonate strata that have been altered to Mg-rich skarn assemblages. Unaltered equivalent strata from a 300 m cored interval in the Yellow Valley Syncline were characterised petrographically and representative samples were analysed for major element compositions. These stratigraphic and chemical units are interpreted to be responsible for the varying skarn lithologies within the DMLZ. The dominant prograde skarn assemblages are controlled by protolith composition, notably the relative abundance of quartz, dolomite, and calcite within the protolith. Models based on isochemical metamorphism of mixed assemblages of quartz and dolomite suggest that the formation of the forsterite-diopside dominant skarn assemblages resulted in the greatest amount of pore space increase. DMLZ Cu-Au concentrations were locally controlled by host lithology, with structural features providing fluid pathways that focused the mineralising fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By N G. Corner

A sea bed sampling programme by CRA Exploration Pty Limited over an area of 12 000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 106 m and contained a high grade core of 33 km2 which averaged 283 mg/m3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10 - 40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 h turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990