Search Documents

By H Ramandi, H Masoumi, I Canbulat, B Hebblewhite, J Oh, S Saydam, W Timms, S Mo

This paper reviews the floor heave mechanisms in underground coal mine roadways. Previous studies have reported three main failure mechanisms: bearing capacity failure, buckling and swelling. The buckling failure has been observed where immediate floor strata are relatively strong and thinly bedded. On the contrary, the weak floor strata have been associated with both the bearing capacity failure and swelling mechanisms. The bearing capacity floor failures are likely to induce other types of instability such as pillar punching, tensile failure of pillar, roof fall and subsidence as well as floor heave. Despite a considerable amount of research, predicting the magnitude, location and timing of floor deformation is challenging with current state of knowledge. CITATION:Mo, S, Ramandi, H, Oh, J, Masoumi, H, Timms, W, Canbulat, I, Hebblewhite, B and Saydam, S, 2018. A review of floor heave mechanisms in underground coal mine roadways, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 196–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

The Circum-Pacific is defined to include back arcs and continental areas of volcanism. Volcanoes must be regarded as dormant, if the time since their last eruption is less than about ten times the average interval between eruptions, even if they have not erupted for tens of thousands of years or longer. It is important to establish a complete history, over as long a period as possible, for varying volumes of eruptions. In order to assess risk, the average interval between eruptions should be calculated for each range of erupted vo4ume~, in orders of magnitude from about 10 m up to the maximum volume possible at each volcano. Eruptions are considered to consist of individual explosions, and are grouped into eruptive sequences, with the sequences grouped into overall cycles of activity. Frequency of eruption versus volume erupted is a linear relationship for most andesitic and basaltic volcanoes, but is often bimodal at rhyolitic volcanoes, 3 with a slower eruption rate above about 10 km. Worldwide, during the last 7000 years, there have been three known e~uptions with volumes of ejecta of > 100 km , a9d, since 1638 A.D., 7 with volumes > 10 km , and 48 with volumes > 1 km . Average recurrence intervals are about 71 years for eruptions of > 20 km , 39 years for those of > 10 km , and 7 years for those of > 1 km . Rough esti- mates can be made for larger volumes erupted. Mean intervals in the Circum-Pacific are about twice the length of those for the world as a whole. During the last 400 years, about 61% of the world's eruptions of > 1 km3 have taken place in this region.

Jan 1, 1987

This paper describes the principle of cut-and-break rock excavation, in which rock is first undercut, and the undercut material is subsequently broken free by a wedging action. The current work on cut-and-break using the large rock cutting test rig at the Centre for Mining Technology and Equipment (CMTE) is outlined, and suggestions are made as to the potential advantages of cut-and-break roadheading, particularly in excavating short tunnels in hard rock in an urban environment.

Jan 1, 1993

By P Gnnther, A M. van Niekerk

Coal mining operations in the Upper Olifants River Catchment in the Mpumalanga Province of South Africa are challenged with the increasing production of excess mine water that cannot be fully managed by existing practices of pollution control at source, recycling, and reuse on mining sites, storage and limited release to the natural water course. In contrast to this, the Olifants River Catchment is experiencing water stress and insufficient water is available to satisfy all water quantity and quality requirements for future industrial and municipal growth. It is estimated that the catchment has a deficit of 192 million m3 per annum if the reserve water requirements are taken into account. The future increased water requirements can be met by water transferred to the Olifants River Catchment from adjacent catchments. The cost of transferred water is likely to be substantially higher than the current cost of water supplied to local municipalities, commerce and industry. BHP Billiton and Anglo Coal Corporation are working together to jointly implement water management strategies that will contribute to the achievement of in-stream and dam water quality and aquatic objectives for the catchment. Consideration is now being given to the treatment and beneficial use of excess mine water. This will inaugurate a new era for the coal mining industry in South Africa, in which a pollution threat to the water resources in the Upper Olifants River Catchment is converted into a water source for beneficial use. Three potential mine water reclamation and reuse schemes have been identified and this paper details the technical, institutional, legal and financial considerations in the implementation of these schemes.

Jan 1, 2006

By A J. MacDonald, M P. Raffield

The South Deep massive orebody consists of 20 to 30 m of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 m and 3400 m. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse various scenarios to aid in the decision process.

Jan 1, 1998

Refractory gold concentrates and their roasted products have been examined by mineralogical and chemical methods, and the distribution of gold in the tailings after leaching has been Investigated.

Jan 1, 1989

By S R. Grano, J Duan, T A, D Fornasiero

We have determined the experimental rate constants for chalcopyrite particles floated from a complex sulfide ore and compared them with those calculated using a recently developed flotation model. The model incorporates contributions from the efficiencies of collision, attachment and stability between particles and bubbles, as well as their frequency of collision. For these calculations, the contact angle of the chalcopyrite particles in the ore was obtained independently using a surface spectroscopic approach. The calculated flotation rate constants were in good agreement with the experimental data and able to reproduce the characteristic maximum in flotation rate constant for particles of intermediate size. The values of bubble velocity and turbulent dissipation energy derived from these calculations are relatively low and may well correspond to mean values of these parameters inside the flotation cell. We have extended this approach through the application of a property based model to an operating plant, with a satisfactory outcome.

Jan 1, 2005

By Gordon DM

SUMMARY Tyres account for 25-30% of the operating costs of large capacity haul units as used in open-cut mines. Tyre operating costs can be substanti- ally reduced and often contained in real terms by applying knowledge that is now available. This paper describes certain specific advances in tyre management, namely batching, bias adjustment, cumulative plotting and the so-called "pressure-temperature" system of tyre pressure control, originated on the Mt. Newman Mining Company's Newman minesite, and discusses the contribution that each has made to improving tyre management and reducing costs. INTRODUCTION Tyres are a significant cost in mining. Tyre costs make up between 25% and 30% of the operating costs of large (i.e. 100 tonne and larger capacity) open-cut mine haultrucks. On a large mine this tyre cost may amount to several millions of dollars each year. It is a fact that through careful

Jan 1, 1982

By Piotto P

Pit optimisation algorithms are designed to produce a pit with maximum value, but for certain minerals like iron ore, limestone, coal, etc, it is also necessary that the designed pit contains ore which meets the customer's chemical specifications. This paper describes a technique of using linear programming for blending optimisation and the Lerchs-Grossmann algorithm (as in Whittle's 3D software) for pit optimisation in tandem, to achieve pit designs of targeted grade specifications.

Jan 1, 1996

By B Shen

The Wambo Rail Spur located near Singleton, New South Wales, Australia, runs for approximately 14 km linking the Mt Thorley rail loop and the Wambo Coal Mine. The project involves a 260 m long tunnel in weathered sedimentary and intrusive materials. The tunnel has a low cover and runs under a main highway. This second paper on the project looks into one aspect of the tunnel in detail: the use of shotcrete arch as the primary support for part of the tunnel excavation. The use of shotcrete instead of steel arch, formulation of the material specification, construction sequencing, installation at the excavated face and material testing for verification related to this facet of the project will be discussed in this paper. The tunnel opened in April 2006, and two years on, we briefly reflect on the impact of this design decision on the overall project.

Jan 1, 2008

Although geophysical methods of prospecting have proved indispensable in the search or oil deposits elsewhere; it is only 'in recent years that they have been used to any significant extent in Australia. The increase in their use has been quite remarkable over the past two or three years, due in Sao small measure to the encouragement given by means of Commonwealth subsidy. There is no doubt that the use of' geophysical methods will coxi-tinue to increase and this increase could be greatly accelerated as and when oil is discovered in commercial quantities,This review of their use A in Australia and the remarks and statistics are confined to work on the mainland. There has been, a substantial amount of geophysical work in Papua, but as operating conditions are so very different to the mainland Papua has been regarded as a separate province.

Jan 1, 1962

By Williams RJ

This paper presents an overview of the design and development , application to date and potential of a real-time return gas monitoring system.Initially developed as an ACARP/Industry funded project, whose prime aim was to create a `turn-key', prototype, stand alone, real-time, Return Gas Monitoring System (RGMS) capable of providing quantitative assessments of gassiness levels on a shift by shift basis, enabling unusual gas emission patterns to be readily flagged.

Jan 1, 1998

The developments in hydrocyclone classification in the milling circuit at Bougainville Copper Limited are discussed. A major change in cyclone size and improve- ments in operating conditions have been made. Test work has been carried out to assess the classification performance of a modified Linatex cyclone, Wemco cyclones and a two stage cycloning circuit. The use of a scalping cyclone, to remove coarse material from the present overflow product for regrind, has also been investigated.

Jan 1, 1978

The Tailings Leach Plant at Chingola employs a Leach/Solvent Extraction/Electro- winning process and contains the largest solvent extraction plant in the world, with design liquor flow rates of 55 m3/min. A pilot plant constructed to provide design data also indi- cated areas of uncertain operating and control performance and led to a decision to model the whole circuit to determine the overall dynamic behaviour and basic operating characteristics. Details of the plant flowsheet are given and the basic physical and chemical' equations required for the simulation defined. Each unit operation is considered separately and details of the mathematical models used for their simulation presented.

Jan 1, 1977

The development of reliable and accurate solution sampling systems plus on-line atomic absorption spectrophotometers and voltammetric analysers at Pasminco Metals - EZ's (PMEZ) zinc refinery at Hobart, Tasmania, has led to extensive implementation of On-Stream Analysis (OSA) throughout the hydrometallurgical circuit. These systems complement industrial autotitrator and colorimetric analysers and with the comprehensive use of a powerful integrated Distributed Control System (DCS), provide extensive monitoring and control of all the important in solution' parameters for the plant. Samples can be left unaltered, or filtered or settled, to remove solids. They are then precision diluted and pneumatically transported to analyser shelters, where they are analysed for zinc, acid, copper, cadmium, lead, antimony, cobalt, nickel, mercury and ferrous, ferric and/or total iron. The range of analyses depends on the sample itself. The results are used for feed forward and/or feedback control of reagents where possible, or simple trend monitoring and out-of-specification alarming when closed loop control is not practical. The overall system reliability and accuracy is such that many daily composite plant samples are no longer analysed off-line. Operator sampling has also been reduced, and in two places, autotitrators with automatic sample pre-treatment have been installed for preparing and analysing samples collected by operators.

Jan 1, 1993

By B Murphy, J van Zyl, G Domingo

In a narrow vein mining scenario, employing preconcentration technology underground not only results in reduced transport and handling costs but may allow alternative mining methods to be implemented, improving overall productivity. Using processing technology underground is not a new concept with underground crushing and screening operations being quite widely utilised. With advances in processing technology over recent years, there are now a number of robust processing methodologies in existence that are capable of performing separation of ore and waste at a relatively coarse size. Many of these technologies are readily adaptable to the underground environment and if employed could result in a number of cost and productivity benefits.Assessment of the oreÆs suitability for preconcentration technology is the first step in harnessing these potential savings. This paper discusses how coarse ore sorting and gravity separation could be employed underground in a narrow-vein scenario and details the test work that is required at the front-end of a project to see if this potential exists.CITATION:Murphy, B, van Zyl, J and Domingo, G, 2012. Underground preconcentration by ore sorting and coarse gravity separation, in Proceedings Narrow Vein Mining 2012 , pp 237-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Hagan T. N, Tucker A. J

The Cumnock Open Cut Mine (COCM) is located in the Hunter coalfield in New South Wales. Five coal seams are being mined, mostly by drilling and blasting, loaders and excavators, and trucks. The annual production of coal is 1.3 million tonnes. Overburden and interburdens consist mostly of siltstones and medium to thickly bedded sandstones. The strata dip to the south-east at approximately four degrees. There are no major faults in the rock mass.

Jan 1, 1995

Projections of metal requirements for Japan and the United States indicate growing competit- ion for Australia's mineral output and a critical need for continuing discovery of new reserves. These projections may be modified by economic, social and political controls - the most import- ant factor probably being a shortage and the high cost of risk and development capital. Changing ownership patterns toward joint ventures and increased state participation are anticipated. New developments in global tectonics and metallogeny delineate favourable zones for ex- ploration and permit establishment of priority search areas even in regions of poorly known geology. Declining ore grades and special character- istics to meet technological requirements may modify identification and evaluation criteria. A broad approach considering all environments of concentration within the geochemical cycle is re- quired within any metallogenic province. The exploration geologist must be able to integrate geological theory, mining technology and financial analysis to establish well defined exploration objectives, in terms of economic and geologic models, in concept-oriented programmes.

Jan 1, 1973

The Permo-Triassic Bowen Basin developed during the final stages of the Tasman Orogenic Phase in eastern Australia. The basin has considerable economic value as a source of coal, natural gas and precious metals. The basin, which is of controversial origin, is preserved as a north-south trending, asymmetrical syncline bounded in places by faults. It is here interpreted as a retroarc foreland basin which developed on the landward (west) side of a continental arc associated with continent-ocean plate convergence. Initiation of the basin occurred via back-arc extension in Early Permian times, coincident with a phase of talc-alkaline arc volcanism. Early Permian, mostly marine sedimentation gave away to extensive coastal and alluvial plain depositional systems in Late Permian times, coincident with a resurgence of arc volcanism. Triassic sedimentation was almost entirely alluvial and coeval with westward propagation of thrust sheets from the eastern basin margin. Compressive tectonics climaxed in Middle to Late Triassic times, terminating sediment accumulation and uplifting the entire area.

Jan 1, 1990