Search Documents

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By Arthur Laing

"IT is indeed a pleasure to have the opportunity of addressing this group today. Not only does it give me the opportunity of meeting with representatives of what is considered by many to be the most dynamic segment of industry in Canada today, but it also allows me to talk about a subject of para-mount interest to myself, the development of the North, and to explain, if even only briefly, some of our beliefs and hopes in this regard.It is inconceivable that all lands north of the 60th parallel, representing 35 per cent of Canada's total land area, which we believe contain a great natural resource potential, will remain as an undeveloped portion of Canada. The re-sources are there, although the people and private industry are as yet not there in sufficient numbers.It has been estimated that in the west and north of Canada there are 1.6 million cubic miles of sedimentary rocks. Of this figure, 342,-000 are thought to lie in Alberta, 115,000 in British Columbia and about 1 million cubic miles are thought to lie in Canada's northern regions, the bulk in the Arctic Islands. On the basis of apparent volumes of sedimentary rock, we estimate that as much as 13 billion barrels of petroleum may lie beneath the permafrost of the North-west Territories, another 3 billion barrels in the Yukon Territory and 33 billion barrels in the Arctic Islands. This is, indeed, a rich and elusive prize, and one which must be sought with a view to fulfilling demands on the production of petroleum."

Jan 1, 1966

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By S M. Roscoe

Relationships of Noranda sulphide deposits to volcanic rocks are reviewed and chemical variations within the volcanic sequence are described. The assemblages of minor elements in the pyrites and pyrrhotites of the Noranda and l\llatagami deposits are similar and are characterized by a high content of cobalt, tin and other elements. Isotopic compositions of lead, other geochronological data and stratigraphically disposed zonal distributions of sulphides and minor elements indicate that the deposits were formed prior to folding and metamorphism. Lead isotope data indicate that the Matagami deposits, and several others, were probably formed about 2.95 x 109 years ago and that the Noranda deposits may be about 50 million years younger. The volcanic sequence at Noranda is younger than the thick sequences bordering it on the east and on the west. The relationships are consistent with the hypothesis that these strata-bound sul1>hide de-posits are coeval with their associated volcanic rocks. T HE writer has been engaged in a metallogenic study of the region between Sault Ste. Marie and Chibougamau. An essential objective of this study is the classification of mineral deposits with regard to their composition, form, geological

Jan 1, 1965

By Gaston Gendreau

CETTE PRÉSENTATION traitera des différentes phases des opérations de la mine du Mont-Wright depuis ses débuts jusqu'à présent. A une brève description de la géologie du gisement, suivra un exposé des méthodes d'exploitation de la mine et du genre d'équipement utilize.

Jan 1, 1977

By C. G. Williams

This paper describes the planning, development and operation of the Highvale Mine to supply coal to both the existing Sundance and the approved Keephills thermal power plants of Calgary Power Ltd. Reference is also made to the company 's Whitewood Mine, which feeds the Wabamun thermal plant .

Jan 1, 1979

By Edgar Stansfield

Introduction First, I should define more closely the vague term 'recent work' that appears in the title of this paper. Following the period of depression that was an aftermath of the first Great War, the Research Council of, Alberta carried on for ten years without a Council and without a financial yote by the Legislature. In November, 1942, a new Council was formed, under the chairmanship of the Hon. N. E. Tanner, Minister of Lands and Mines, and a vote was granted by the Legislature early in 1943. By 'recent work', I mean work during the present regime. The Council is now going full steam ahead, or would be if it could get suitable technical assistance and required apparatus and materials. Lack of these has so far made unnecessary my responsibility for seeing that we do not exceed our estimates. The Annual Meeting of the Research Council will be held in November (1945), and at that meeting the programme of work for next year will be discussed. The present time is therefore the correct time for any of you who may have ideas as to work which might profitably be undertaken by the Council, to submit these ideas for consideration. I propose to discuss my subject under several headings, and to give enough of these to show that the Council has wide interests.

Jan 1, 1946

By G. R. Heffernan

"IntroductionTHE PURPOSE of this paper is to give a •brief history of iron and steel in British Columbia, a quick look at the present operations of Western Canada Steel, Limited, a review of iron ore resources and iron and steel markets, and a projection of what the future might hold for the industry in British Columbia.From the Past to the PresentWhile the paper is entitled Past, Present, and Future, in covering the past, which we shall call the time prior to 1947, there is very little to be said. Small shipments of iron ore were made from the Texada deposits by the Puget Sound Iron Company from 1886 to 1907. Total ore shipped did not exceed 70,000 tons. Part of this is believed to have been used in building a United States battleship in 1907 in the Bremerton Naval Yards in Seattle, Washington.In 1914 a small steel mill was started on Lulu island, rolling bars from •box piles and used shafting. This mill operated spasmodically for a few years but finally burned down in 1921. The rolling mill stands were sold to China and are no doubt in operation in China today.In 1916 the City of Port Moody assisted in the financing of a mill which operated on re-roll rails, box piles, and steel ingots made in an experimental electric furnace in Port Moody. This furnace also produced small quantities of pig iron scrap. The backers of the Port Moody mill showed a great deal of enterprise and must have been a very forward looking group, since this was one of the first recorded applications of the electric furnace to small ingot production. Despite their enterprise, the operation was unsuccessful and terminated in 1921."

Jan 1, 1953

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

By Fred W. Snow

THE mines of the Consolidated Copper and Sulphur Company, consisting of the Eust1s, the Albert, and the Capel mines, are situated w Ascot township, Quebec, about ten miles southeast of Sherbrooke, on the main line of the Quebec Central railway. Of these mines, only the Eustis is now producing, and it has been operated almost continuously for the past seventy years. Mining methods have been improved in recent years but are still old fashioned when compared with those employed in more modern and up-to-date mines. The ore is of milling grade and is mined for its copper and sulphur con-tent. Silver is present in small quantity, together with a trace of gold. The ore is mined by the shrinkage stope method. Pillars are frequently left as supports for the hanging-wall to prevent serious dilution of the ore and are sometimes recovered after the ore is drawn from the stope. Occasionally, small blacks of ore in close proximity to the shaft are mined by a cut-and-fill method. HISTORY ALBERT AND CAPEL MINES: The Albert and the Capel mines, originally known as the Capelton mine, were discovered in 1863 by George Capel (1). By the end of 1866 the Albert shaft had been sunk to a depth of 121 feet on an incline of about 30 degrees where a vein five feet thick was encountered. In 1879, these mines passed into the hands of G. H. Nichols and Company, by whom they were operated practically continuously until 1907. When mining operations ceased in that year, the shafts had reached depths on the incline of approximately 2,300 feet and 1,000 feet, respectively. These mines have been allowed to cave and fill with water and have been inaccessible for many years.

Jan 1, 1936

By A. Ignatieff

Introduction Some interest is being shown in Canada in underground gasification of coal and, as developments have now taken place in several countries of the world, it is thought that a review of progress, particularly from the viewpoint of a mining engineer, may be of interest. The literature on the subject, and notably that of Russian origin, is already very voluminous. The various methods of underground gasification of coal have evolved from initial attempts to employ underground workings as gasifiers of previously fragmented coal or to use some method that involves little or no preparatory work underground. The 'stream' method, shown schematically in Figure 1, has been the only one used in tests to date in countries outside the U.S.S.R. Other methods, involving preparatory work underground prior to gasification, are the early 'chamber' method, where fragmented coal was gasified in rooms between inlet and outlet entries, and the underground borehole' method, illustrated in Figure 2, where gasification is developed in a succession of boreholes which are temporarily sealed and then abandoned in turn after gasification. The stream method appears. to be particularly suitable for pitching seems as it is claimed that the pitch prevents ash accumulation or serious blockage from roof falls, and it also aids the circulation of the stream. As a considerable proportion of Canadian medium and high-rank coal seams are inclined, it would seem that, at least at the outset, the stream method or a modification thereof would be the one most applicable to all but the Saskatchewan lignite fields and the flat domestic-coal fields of Alberta.

Jan 1, 1949

By Ben Sheneider

AT THE Flin Flon plant of the Hudson Bay Mining and Smelting Co., Limited there are two types of multiple hearth furnaces used in the roasting of sulphides. This pa-per will deal primarily with the wedge-type furnace in the roasting of zinc concentrates. The other furnace, the Nichols-Herroshoff type, is used in the copper smelter and is described in the papers given by (1) J. H. Ambrose in 1935 and (2) R. E. Mast and G. H. Kent in 1954. The design and operation of these roasting furnaces at the present time is essentially the same as given in the write-up in 1954. No at-tempt will be made here to describe these furnaces, except to mention that there are five Nichols-Herreshoff multiple-hearth furnaces, four of which are used to roast a dried mixture of copper concentrate, zinc plant residue, and flux, before this material is fed to the reverberatory furnace.

Jan 1, 1961

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By J. Güntner

A significant portion of Outotec's business relates to the application of fluidized bed for processing a wide range of industrial materials, including gold ore and gold concentrate. As part of the former Lurgi and Boliden organization, our division constructed the first industrial reactor for roasting sulphur-bearing materials in 1950, based on the principles of fluidized bed technology. This process, when combined with efficient heat recovery and off-gas treatment and its conversion to sulphuric acid, became the standard for processing sulphur-bearing ores. In the last 60 years we have delivered more than 265 plants and developed (in addition to the standard fluidized bed solution) variants of the fluidization technology, such as the circulating fluidized bed and the bubbling fluidized bed. This paper describes the different options of the fluidized bed technology for gold roasting reflecting on main process design criteria.

Jan 1, 2011

By A. Alfantazi, M. Mahon

The current efficiency in zinc electrowinning is a key indicator of the performance in a cell house. This is typically measured by comparing the weight of the cathode to the electric current applied over the deposition period. This calculation can be cumbersome because the deposition history of each pulled set of cathodes will be unique. It will depend on the applied current and electrolyte conditions from onset of deposition until the cathode is removed and stripped. Not accounting for these can introduce errors to the calculated current efficiency. To track this history and reconcile the current efficiency, a time based computer process simulation was made of an industrial cell house. Two months of hourly recorded measurements from the cell house were input to the simulation, including current to the cell houses, concentrations, flow rate, and temperature of the purified leach solution. The simulation’s predictions of the concentration of zinc in the circulated, spent, and returned electrolyte all showed good agreement with the industrial data over the two months giving a validated zinc balance. The simulation was then tuned to predict the instantaneous current efficiency for all times, as well as the expected masses for the deposits given their deposition history.

Jan 1, 2014

By W. D. Bonisteel

In 1976, Rio Algom Limited began the expansion of uranium production facilities at Elliot Lake. Quirke Mine was the only property in operation at the time, and plans were made to expand its milling capacity from 4,500 to 7,000 tons of ore per day. Following this expansion, other properties in the area will be reactivated to fulfill long-term contracts for uranium. As part of the expansion program, it was decided that in view of the escalating cost and impending shortage of energy, heat reclaim and conservation would be employed wherever practicable. In general terms, heat reclaim applications fall into three main classifications: ventilation, utility and process. Two of the ventilation applications and one process application will be described in some detail. Several other systems will be presented briefly as a matter of general interest. Some future possibilities will also be mentioned, together with their potential for economical heat recovery.

Jan 1, 1979

This paper discusses three case studies conducted at Highland Valley Copper mine (HVC) that illustrate operational improvements and insights which resulted from using the McGill University gas dispersion sensors. In the first study, the superficial gas velocity (Jg) sensor was used to implement a gas profiling control strategy for the rougher, scavenger and first cleaner cells in the Cu/Mo separation circuit. The data showed a 40% reduction of down-the-bank Cu recovery at constant Mo recovery which resulted from operating the cells at the target profiles. In the second study, the bubble size analyzer was used to better understand two mechanisms of bubble formation in the two flotation columns that make up the final Mo cleaning stage: the conventional rubber-sleeve sparger and the Microcel(TM) system. The data showed a considerable reduction of bubble size in the Microcel column which resulted in a significant increase in concentrate quality (1-2% Mo absolute) and a dramatic (4-5 fold) increase in concentrate production rate compared to the typical operation. The estimated economic benefit resulting from the improved column flotation operation was an overall 4% increase in Mo circuit recovery. In the third study, real-time measurements obtained from the gas holdup and bulk density sensors were used to infer the pulp density (% solids) in a rougher cell of the bulk flotation circuit. Validation tests demonstrated that this approach provides reliable pulp density measurements. Although promising, more work is required before implementing this approach at HVC.

Jan 1, 2009

By Michael T. McCaffrey

The wide range of potential feed materials, process steps, and products in metallurgical facilities means that standard equipment might not be available to adequately meet the project technical and economic needs. Custom designed equipment should be considered only after rigorous research precludes purchasing standard equipment. However, the decision to use custom equipment introduces a new element of risk into the project. To manage the risk, custom equipment design should be developed through the same front end loading (FEL) phases as project development. If more than incremental development of custom equipment is required, appropriate test work or pilot trials are required to test key uncertainties. Important activities during custom equipment design include maintaining clearly defined performance objectives, conducting appropriate reviews, carefully crafting commercial and intellectual property agreements with design and fabrication partners, and assembling a multidisciplinary team with sufficient development expertise.

Jan 1, 2015