Search Documents

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By Étienne Yvenou, Martin Désilets

Le procédé d’électroaffinage du Cu est nécessaire pour atteindre les niveaux de pureté requis pour les applications les plus courantes telles que son utilisation comme conducteur électrique ou thermique.

May 2, 2024

By J. J. O?Neill

Introduction The Beattie mine is the first of its character to be exploited in Quebec. It is primarily a large low-grade gold deposit containing values which a few years ago would not have been considered as ore. Much interest is attached to this development as its success may mean a greatly enlarged scope to gold mining in Canada on deposits which have formerly been considered worthless. Because of its potential importance as a pioneer in low-grade gold mining, the Quebec Bureau of Mines decided to make a careful detailed study of the Beattie in the hope not only of assisting in its development, but of stimulating the search for similar essential geological conditions in other parts of the Province. This paper is a summary of the results obtained during two months on the property in 1932, supplemented by a few trips underground in 1933. The full report will appear in the Annual Report of the Quebec Bureau of Mines for 1932, Part C. Location and Means of Access: The Beattie ore-body is situated two miles west and one half mile north of the centre of Duparquet township, and approximately 22 miles north 28° west of the town of Noranda. Until the fall of 1932, access to the property was from LaSarre, on the Canadian National railway, over a thirty-mile water route with one portage 600 feet long; about 2,000 tons of machinery and supplies were taken in by that route. An automobile road, nine miles long, now connects the property with the Makamik highway, and a narrow-gauge railway, without ballast, gives outlet for concentrates from the mill to the C.N.R. tracks of the Rouyn-Taschereau line, nineteen miles distant.

Jan 1, 1934

By R. A. Hemstock

"OIL EXPLORATION in Western Canada has produced outstanding results in the past few years. From such successes as Leduc and Redwater on the western plains, oilmen are now moving north in the ever-widening search for oil. They are reaching new frontiers and meeting new problems presented by this vast hinterland.One of the least known but most troublesome phenomena which will be encountered is permafrost. This term relates to a thickness of soil or other superficial deposit, or even of bed-rock at variable depths beneath the surface, in which a temperature below freezing has continually existed .for a long time. This permanently frozen ground affects, in many ways, oil exploration and exploitation. Seismic records are changed, pipe lines cannot easily be ditched into the ground, formation of wax is speeded-up in tubing and pipe lines, roads are difficult to build, and foundations of buildings and even of drilling 'rigs may require entirely new methods of construction.Permafrost underlies roughly one-fifth of the entire 'land surface of the world. It covers the northerly portions of Eurasia and North America. In the area that we are here concerned with, the southern boundary of permafrost extends south of east from about latitude 59°N. on the Pacific coast across the Rocky mountains, through Great Slave and Athabasca lakes, to cape Henrietta Maria, at the junction of Hudson bay and James bay (see Figure 1). Geologists generally agree that permafrost first appeared in the Pleistocene or Ice Age as the result of abnormal ground freezing."

Jan 1, 1952

By J. Shibata, N. Murayama

"Rare earth elements are present in more than 100 minerals, of which monazite, bastnaesite and xenotime are typical. Rare earth elements have excellent chemical and physical properties for industrial use in functional materials such as phosphors, magnets, electronic components, abrasives and catalysts. China produces more than 90 % of the world’s rare earths, and Chinese trends significantly influence the demand and price of rare earths. From the viewpoint of resource securement, it is desirable to separate and recover rare earth elements from low-grade resources and wastes. Phosphate gypsum, which is a by-product of wet phosphoric acid manufacturing, contains low concentrations of rare earth elements. In this research, the separation and recovery of rare earth elements from phosphate gypsum were investigated. A series of recovery methods including washing of phosphate gypsum, leaching of the rare earth elements with sulfuric acid, adsorption and desorption of rare earth elements by using ion-exchange resin, and precipitation of rare earth oxalates were carried out. The separation of rare earth elements from Ca2+ simultaneously leached from phosphate gypsum was also investigated."

Jan 1, 2014

By M. Piche

The western part of the Hauy Formation of the Opemisca Group, occurring near the town of Chapais, is described in this paper. As it has been defined previously, the Formation is composed of a succession of subaerial andesi tic lava flows with some interbedded proximal volcaniclastic sediments. Towards the East, these volcanics yield to coarse grained fluviatile sediments having similar composition to the interbedded lavas. Further east, the composition of these sediments is more arkosic with dioritic and tonalitic fragments. It is proposed that these arkosic sediments are a part of the Stella Formation which has been described by Dimroth et al. (1982).

Jan 1, 1984

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By K. Robertson, K. A. Scalise, K. C. Kocsis, M. B. Teixeira

"Many deep and highly mechanized underground metal mines require cooling. In many cases, appropriate working conditions might be fulfilled by ventilation alone, but some require the implementation of cooling systems. The most common cooling systems are bulk air cooling and localized cooling. These systems are effective, but they use considerable amounts of electricity. Ground source heat pumps (GSHP) can supplement existing cooling and heating systems, while geothermal systems can cool the mines in their entirety if there are significant sources of geothermal energy are present. A major advantage of geothermal and GSHP systems are their renewability, which reduces the carbon footprint of the mine.INTRODUCTIONThe western United States has abundant alternative energy sources including a high potential for geothermal energy. Geothermal utilization is a viable energy alternative that many areas throughout the world have access to because high geothermal potentials are located near areas of volcanic activity such as along plate boundaries, mid-oceanic ridges, rift valleys and hot spots (IRENA, 2017). There is significant potential to use geothermal energy for many applications. With constantly evolving and innovative technologies being developed, an increasing number of geothermal applications are becoming feasible. The western United States is an ideal candidate for alternative energy applications due to the geothermal availability and the emergence of modern technology. This paper investigates the incorporation of renewable methods and the alternative energy possibilities of Barrick Goldstrike, located in northern Eureka County, NV and Rio Tinto/BHP Billiton’s Resolution Copper mine located in Superior, AZ.RENEWABLE SYSTEMSGeothermal SystemsGeothermal temperatures are typically defined as either high or low temperature systems(Shengjun, Huaixian, & Tao, 2011). The high-temperature reservoirs (>220°C / 428°F) are feasible forlarge, commercial production of electricity with dry stream and flash stream systems (Shengjun, Huaixian, & Tao, 2011). Low temperature systems, below 220°C (428°F) (Shengjun, Huaixian, & Tao, 2011), aremuch more difficult to use for energy production. Low-temperature reservoir heat can be harnessedthrough the implementation of a binary cycle plant. The working fluid for a binary cycle plant is eitherorganic (Organic Rankine Cycle (ORC)) or an ammonia-water mixture (Kalina cycle). Organic fluids andammonia-water mixtures have low boiling points that allow for the recovery of heat from low-temperaturesources (Eymel Campos Rodriguez, et al., 2013). The efficiency of the binary cycle plant varies depending upon the fluid, thus the proper selection of the fluid is critical for maximum energy output"

Jan 1, 2019

By Bill Charbonneau

Lumen, lm The measurement unit of light emitted by a light source 60W incandescent840 lumens 32W T8 linear fluorescent3200 lumens 54W T5HO linear fluorescent5000 lumens 400W metal halide24,000 lumens

Oct 1, 2010

By F. R. Deluca

"ClassificationClassification is a combination of mechanical and hydraulic operation which separates a pulp into two portions according to their respective settling rate. The finished product, the overflow, is removed from the other product, sand, which requires further grinding.Pulp is the uniform suspension of solids in a liquid. Overflow is the fines and therefore the more slowly settling portion of the pulp which is carried over the top of the classifier by the flow of water; sand is the coarser and more rapidly settling portion of the original pulp which is discharged from the classifier by the mechanical action of the rakes or conveyed out by a ""screw"" .Selective classification is classification that has for its object the concentration of the heavy constituents of the original pulp in the sand product so that it may be ground finer than the lighter constituent.Classification is used as follows:I. To make a size separation, for example, a sand-fines separation so that each product may be given a different treatment.2. For closed circuit grinding so that the maximum size of particles entering the circuit is limited, and so that the useful work is increased by enabling the mill to operate mainly on the particles that require the reduction.3. For differential grinding of the heavy mineral constituent and the gangue. In this case, the heavy mineral is concentrated in the sand product and is reduced further, while the lighter gangue material overflows the classifier.The selection of the proper size and type of classifier is determined by the function required, the character of the ore, and the tonnage to be handled, the initial cost and the operating cost."

Jan 1, 1989

By Roy T. Bowles

This paper focusses on technological developments which occurred in the village of Deloro, Ontario between 1868 and 1919. These developments illustrate the manner in which improved metallurgical processes linked Ontario mineral resources to industrial expansion. Overview of Deloro The village of Deloro is in Hastings county, about 5 miles from the village of Marmora, the site of the old Marmora iron works and the more recent Marmoraton iron mine. In this area, the Canadian Shield meets the Great Lakes lowlands. The first settlement in the vicinity occurred in the 1820s and was associated with the Marmora iron works. Settlement grew around agriculture. Gold was discovered in Hastings county in 1868. Deloro - the name derives from gold - developed as a concentrated settlement in proximity to several gold mines and the related processing activities. By 1901, substantial smelting works were successfully producing gold and arsenic from local ores. The village was developing as a company town within the framework of benevolent paternalism. For reasons associated with markets and with local ore supplies, the Deloro mills were idle for a period beginning in 1902. Developments in later periods connected Deloro to world events. In 1903, silver was discovered at Cobalt, Ontario. By 1907, M.J. O'Brien, who owned mines at Cobalt, had purchased the Deloro works and was using them to process Cobalt-area ores*.

Jan 1, 1999

By W. G. Worcester

THE chief object in presenting this paper on bentonite is to attract general attention to one of the least known and most neglected industrial minerals of Canada, a mineral of extensive commercial possibilities, as evidenced by its development and exploitation in other countries, principally in the United States and Germany; countries upon which some of our most important Canadian industries are dependent for their supply of special clays, such as Fuller's earth and activated bentonite. It was in view of these conditions and the knowledge of the presence of large quantities of bentonite in the Canadian West that the work here reported on was under-taken. While the investigational studies have not been completed, the results indicate that among the many samples tested there are some of real merit and industrial importance. While it has been the author's privilege to examine deposits and samples of bentonite from all of the Western provinces, his chief activities in the field and in research studies have naturally been confined largely to Saskatchewan materials. Notwithstanding this, however, this paper is presented in the hope that it may stimulate a more general interest in, and study of, Canadian bentonites as a whole, a matter of such importance that provincial boundary lines should be overlooked. GENERAL CHARACTERISTICS OF BENTONITE According to Schurecht and Donda (1), bentonite is commonly composed of the mineral montmorillonite, (Mg,Ca)O.Al203 5SiO2 .nH2O, though some are known to consist of beidellite, Al2O3 3SiO2.nH2O: where n is approximately 4, and in certain cases the Al2O3 may in part be replaced by Fe2O3. For present purposes, however, it may be sufficient to state that, in general, bentonite is a "soapy' clay-like mineral or group of minerals composed largely of hydrous aluminium silicate, but frequently carrying small percentages of the alkalies, alkaline earths, and free silica, as well as silicates, gypsum, and other admixed detritus such that purification is usually necessary.

Jan 1, 1937

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By Mohamed Hamoud

Relative permeability curves represent an important element of special core analyses, but challenges remain in obtaining valid results and the extrapolation and use of existing permeability results is problematic. This situation is compounded in cases where core properties are altered from changes in effective stress. During the production of oil and gas reservoirs, the effective stress changes as a result of changes in pore pressure or temperature. Therefore, changes in rock properties such as porosity and permeability will occur and will consequently influence reservoir performance calculations. An experimental program was carried out to understand the behavior of dense, reconstituted sand samples at low effective stress states. Drained triaxial compression tests were set up to study the effect of stress alteration on relative permeability data through porous media. Initially, a saturation stage was performed followed by isotropic loading to bring the core sample to reservoir fluid and stress conditions. Then, while axial (deviatoric stress) loading was applied to the sample, a series of absolute and relative permeability tests was performed under steady state flow at different levels of strain during pre and post peak shearing stress. The stress-strain behavior results from the study revealed that the absolute permeability decreased during isotropic loading (compaction) and increased during shearing (dilation). However, the shape of relative permeability curve changed from contraction to dilation and showed higher initial kro and the lower initial kro respectively. The goal of this project was to understand the behavior of both absolute and relative permeability at different stresses. It is expected that geomechanical processes will be adopted for special core analyses to support the current integration of geomechanics into reservoir engineering. This will be required if, during SAGD, conventional and/or unconventional reservoir simulation, reservoir engineers implement a proper set of relative permeability data at each in situ state of stress, instead of constant curves throughout the field?s life.

Jun 1, 2012

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By K. Soucek, J. Ptácek, A. Hastíková, R. Kukutsch, P. Konícek, P. Waclawik

"Cable bolts are used frequently as a secondary support system (with steel arch support) in difficult stress-strain conditions of deep coal mines. The load transfer mechanism of cable bolts depends on several factors, such as the strength, deformation and geometric properties of the bolts, resin and the surrounding rock mass so-called cable-resin-rock system (CRR system). The bonding length and bolt/borehole diameter ratio strongly influence the final bearing capacity of the CRR system.The study presents the behaviour of CRR system during a pull-out test which is usually used in the carboniferous rock mass in the Czech part of the Upper Silesian Coal Basin. A series of 28 pull out tests were performed on 3-m-long cable bolts, with various combinations of borehole diameters and bonding lengths, to understand this behaviour. Boreholes were drilled into a solid rock mass consisting of fine-grained sandstone to guarantee similar conditions during the pull-out tests. Video inspection and measurement of borehole diameters were performed to determine their quality and real diameters. Three characteristics were observed from pull-out test results: ultimate pull-out load; displacement of the end of bolt and system stiffness. Numerical modelling by FEM (Finite Element Method) was used to determine the stiffness of the CRR system for variable bolt/borehole ratios and bonding lengths each under constant load. A linear elasto-plastic model and a mohr-coulomb model were used for cable and resin-rock respectively. The results of the experiment may contribute significantly to improving of the methodology of cable bolts installation as well as the design of used cable bolts."

Jan 1, 2015

By W. A. Crosby, W. K. Smith, K. L. McDonald

"IntroductionThis paper describes how the introduction of two blasting techniques and the resuItant development of new dragline digging methods have increased the productivity of single- and double-seam dragline operations at the Rietspruit opencast mine.LocationRietspruit , one of South Africa's largest opencast strip mines, is situated some 11 5 kilometres east of Johannesburg in the Witbank coal field.BusinessRietspruit is a joint venture between Transvaal Consolidate d Land and Exploration Company (T.C.L.) and Shell, South Africa. Rietspruit is administered and managed by Rand Mines, the Mining division of Barlow Rand, transportation and marketing being the responsibility of Shell. The total saleable coal product, approximately 5,5 million tons per annum, is exported via Richards Bay.Presplitting and Throw BlastingPresplitting was initially introduced in September 1980, as a means of dewatering t he overburden and mid burden to facilitate the use of dry-mix explosives a s opposed to slurry explosives.The utilization of the throw blasting technique arose as a direct result of observed ground movement after the successful introduction of presplitting. The first trials commenced in March 1981 on the double-seam operation. The methods, economics and resulting advantages are fully described elsewhere. A brief description follows.Method of PresplittingAfter determining the desired presplit line, 250-mm holes are drilled to top of coal at 4-m to 6-m intervals, dependent on the competency of the rock overlying the coal. A single 60-kg charge of slurry explosives is located at the bottom of each hole, no tamping is used and all the holes are detonated simultaneously. The results are a competent, straight, vertical highwall. This enables accurate control of the first row of blast holes closest to the highwall, which is a prime requisite for successful throw blasting."

Jan 1, 1983

By L. Voisin, K. Itagaki

In the reductive smelting of the copper concentrate like a blast furnace operation using coke as fuel and reductant or in processing the copper concentrate which contains coal in the bulk, a sulfur-deficient matte phase often coexists with an iron base alloy in the bottom of the smelting furnace. This alloy is generally called furnace residue or speiss when considerable amount of arsenic or antimony is contained in the alloy and in the extreme case of reducing condition the alloy is saturated with carbon. As a fundamental study to know the behavior of some precious metals such as silver, gold and platinum between the sulfur-deficient matte and the furnace residue or the speiss which are in equilibrium under reducing condition, the phase relations and distribution of precious elements in the Cu-Fe-S-As and Cu-Fe-S-Sb systems saturated with carbon were determined at 1473 K by a quenching method.

Jan 1, 2007

By L. J. Cunningham

I THINK it can be safely said that no mining operation, whetl1er open-pit or underground, is ever entirely free of water. It follows that every ton of ore bears a charge which represents, either directly or indirectly, the cost of keeping the mine workings as dry as possible. Water problems occur in all phases of mining operations. They cause difficult and costly drilling conditions during the exploration stage, they often seriously delay mine development, they can slow mine production and reduce efficiency, and they are a continued burden over the life of the mine. It is therefore in the interest of all mining men to be familiar with the methods and materials used for grouting. The most common grouting material is cement. Cement grouting is old and well established, and many engineers are familiar with its uses and limitations. The technique of cement grouting is relatively simple and fairly well understood, and the materials utilized are relatively in-

Jan 1, 1962