Search Documents

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts

By R. Lincoln

A surplus of vanadium has resulted from the tremendous output of uranium, of which vanadium is a byproduct. More knowledge of the properties and characteristics of vanadium as a pure metal has been needed so that industry can take advantage of its availability and use it according to the best principles of conservation. Besides the problem of utilization, there is the ever present need of finding new materials which will satisfy specific and demanding requirements of science and engineering; vanadium or one of its alloys may possess the latent potential for filling some of these needs. Thus this? research project was undertaken by the Bureau of Mines to determine and examine some of the physical and mechanical properties of pure vanadium. A corallary investigation was the determination of the effect of the interstitial contaminants, oxygen, nitrogen, and carbon, on unalloyed vanadium. The vanadium used for these determinations was principally the product of experimental production of the Bureau. The evaluation of this material, as small quantities became available, provided most of the data that have been obtained.

Jan 1, 1962

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Ernest A. Curth

Statistics For 1956-66 show that mine transportation accidents accounted for 19 percent of fatalities in bituminous coal mines, second only to roof deficiencies as a cause of death. Productivity per man-shift increased from 10.2 tons in 1956 to 18.4 tons in 1966, but the fatalities per million man- hours of exposure also increased from 0.19 to 0.21 during that same period, indicating that transportation hazards still persist. Consequently, the Bureau of Mines reviewed the transportation fatalities that occurred in bituminous coal mines during 1956-66. The data were processed by computer to find what constitute hazardous conditions and unsafe actions as well as to correlate occupation and age of victims, transportation type, and mine production. Environmental factors and equipment defects which create hazards, as well as unsafe actions of personnel, were determined for each type of mine transportation: Track haulage, mobile nonrail haulage, conveyors, hoists, automotive operations, and front -end loaders, and for transfer stations (loading points, slope and shaft bottoms, surface transfers) and railroad yards. Man-trip accidents, a group with a catastrophe potential, also were analyzed. The basic design and operational features of each transportation type were outlined and procedures considered safe in the light of accident experience were suggested. Findings show that unsafe actions of personnel and hazards created by environmental deficiencies or equipment malfunctions contribute equally in causing transportation accidents. Accordingly efforts should be directed toward improving working conditions, equipment maintenance, and education and training of employees. The trend is toward using safer modes of transportation, notably conveyors. More attention should be given to track haulage operation, railroad yards, and nondestructive field testing of materials.

Jan 1, 1971

By P. R. Jones

A computer program was written for the design of a shell and tube type heat exchanger on a price optimum basis. The program was designed to meet the following requirements: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; and (4) no change in phase. Price optimum design was obtained for four standard tube sizes and standard pitch. Pressure drop both inside and outside were computed and the nearest standard shells having at least the required area were listed. With this information, the estimator can select the heat exchanger best suited for the need. The program was made adaptable to various fluids and to various tube sizes and spacing by reading in much of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1967

By Russell E. Griffin

The current state-of-the-art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in underground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long-term in-mine tests are presented.

Jan 1, 1979

By Robert E. Barieau

A list of 163 references to original experimental PVT data on helium is presented for the period 1895 to 1968. The list is complete as of the start of the Helium Centennial Year, 1968, to the best of the author's knowledge. Citations were keypunched for easy updating and are listed alphabetically by author.

Jan 1, 1968

By Heber E. Peterson, Sill. Claude W.

"INTRODUCTION In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate. It seemed likely that the same general procedure could be used in determining semimicro quantities pf uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant in turn permits the use of the very stable indicator, ferroin; with its sharp color change and exactly reproducible blanks.Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Glen (5). The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months."

Jun 1, 1952

By William O. Vanderburg

This report3/ gives the reconnaissance of a reconnaissance of the mining districts in Churchill County, Nev., made in the fall of 1938 and spring of 1938 All of the mining districts in the county were visited, but no attempt has been made to include all the mines and prospects within the area; inclusion or omission of a property in this paper has no bearing on its merits, The report gives the situation of the various districts, mineral production, and ownership of properties; describes the ore deposit, mines, and prospects; contains information on past and current activity; and includes other data likely to be useful to those interested in the development of our mineral resources. The various district, were named when they were organized for purposes of record and regulation. When established, the districts embraced large areas n without well- defined borders, so that the names have little geographical significance.

Jan 1, 1940

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By G. L. Oldright

This paper is the second of a series that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. The writers wish to express their appreciation to the management of the International Smelting Company at Tooele. Utah, for their kind cooperation which made possible the assembling of these data.

Jan 1, 1929

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

Chromium, a critical mineral for which the United States is largely dependent on foreign sources, is the subject of a new report just issued by the Interior Department's Bureau of Mines. The report is the first in a new series called "Mineral Commodity Profiles" (MCP's). Designed to give an updated review of important events affecting critical minerals, it also presents a comprehensive description of industry structure, supply-demand relationships, technology, and outlook for the future.

Jan 1, 1977

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of canopy air curtain devices under Bureau of Mines Contract H0232067. The canopy air curtain device is designed to reduce the level of respirable dust exposure to a continuous mining machine operator while having a minimum effect on operator safety, mobility and comfort and being compatible with mining equipment. This contract was devoted to the development of a device which utilizes an invisible curtain of air to envelope a mining machine operator's breathing zone with filtered air to provide respiratory protection. Various concepts were evaluated by means of laboratory tests. One concept was selected and was tested on various mining machines at underground sites by means of MSA personal samplers. The canopy air curtain was found to be effective. The percent reductions over the ambient dust concentrations were about 30 to 75 percent depending on the amount of time the operator spent under the air curtain. At one test site, the device enabled the mining machine to operate within compliance. Donaldson Company is presently working on the commercial production of the device.

Jan 1, 1975

According to reports in August, Botswana RST's copper- nickel-cobalt smelter at Selebi-Pikwe produced 7 percent above the rated capacity of about 3,500 metric tons of matte per month. This record production occurred after 2 years of plant production difficulties and was brought about by a new management team. A shutdown for furnace maintenance had been planned for this year, but was postponed because of the improvements in production and operations. However, the mining operation continued to face problems relating to higher costs and some outstanding claims. COPPER: Effective December 1, ASARCO, Inc. and Phelps Dodge Corp. reduced their domestic copper prices by 54 per pound. Within a period of 3 days, a11 other producers (Kennecott Copper Corp., Newmont Mining Corp., Cities Service Co. , Copper Range Co. , Duval Corp., and Inspiration Consolidated Copper Go. ) had either lowered or discounted their market postings by 5¢ to 65.625¢ per pound on electrolytic wirebar and 65$ on cathode plate. Between November 29 and December 3, New York merchants decreased wirebar quotations by 1.8¢-2¢ to within a range of 57.8¢-58¢ per pound. New York Commodity Exchange (COMEX) spot-contracted copper in the week was priced at 57. 1¢ on Monday, 56.7¢ on Wednesday and Thursday, and 57.4¢ on Friday, resulting in a 5-day average of 56.9¢, London Metal Exchange (LME) cash (prompt) wirebar averaged 56.3¢ last week, opening Monday at 56.6¢, falling from Tuesday?s high of 57.2¢ to Wednesday?s low of 55.6¢ and closing Friday at 56.1¢. Foreign producers, guided by LME market transactions, lowered wirebar quotes to 56¢ per pound. Copper stocks as of December 3 totaled 187,702 short tons at COMEX warehouses and 654,573 tons at LME depositories, compared to 97,413 and 537,481 tons, respectively, for the corresponding 1975 period.

Jan 1, 1976