Search Documents

By V. F. Parry, W. S. Landers

"INTRODUCTION The primary object of this investigation was to determine changes in physical and chemical properties of subbituminous lump coal while in storage for 8 months in a typical residence and to demonstrate how this fuel may be stored without degradation or spontaneous combustion. The second object of the study was to determine how the stored coal performed in a hand-fired furnace operated under practical conditions.The investigation revealed that if care is exercised in placing sub-bituminous lump coal in a closed bin, no significant slacking or degrada¬tion occurs, no hazards arise, and over-all indicated efficiencies of about 65 to 69 percent can be obtained under practical,firing conditions that the average home owner can meet.Owing to the war emergency, much attention is being given to the proper storage of coal, and campaigns are being conducted to increase the quantity of coal being stored to relieve transportation and production overloads. Ordinarily, coal dealers do not recommend storage of subbituminous coal in homes owing to deterioration of the coal and to possible hazards from spontaneous combustion. This practice has grown from some troubles that have been experienced, which can be traced to improper preparation, improper bins, and poor technique in placing coal in a bin. There is no good reason why subbiturninous lump coal cannot be stored safely in homes."

Jun 1, 1944

By David A. Benjamin

The USBM (U.S. Bureau of Mines) studied mines, prospects, and mineralized sites in the Roberts WSA (Wilderness Study Area) in 1984. The 15,090-acre WSA, located 35 miles northwest of Eureka, NV, is underlain by alluvial deposits of Quaternary age, extrusive and intrusive volcanic rocks of Oligocene through Miocene age, and metasedimentary rocks of Cambrian through Permian age. The Roberts Mountain Thrust fault cuts through the WSA, dividing the metasedimentary rocks into upper and lower plate rock units. One mine, the Kelley, which produced 397 tons of lead-zinc ore prior to 1940, and two prospects are within the WSA; no resources were identified. Exploration for precious metal deposits is presently being conducted in and adjacent to the WSA on large claim blocks. The study area contains six sites in and near these claim blocks that have anomalous gold and silver. Detailed exploration is needed to delineate resources. High purity silica rocks are present in the WSA. Barite, phosphate, oil shale, and vanadium occurrences just outside the WSA may extend into it, but no such occurrences were observed during the USBM study.

Jan 1, 1986

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

[In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or a blasting device enumerated in the permissible lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.]

Jan 1, 1941

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or y blasting device enumerated in the permissible Lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1941

By H. E. Camargo

In an effort to decrease noise-induced hearing loss (NIHL) in coal preparation plant employees, the National Institute for Occupational Safety and Health (NIOSH) is conduct­ing research to identify and control dominant noise sources in vibrating screen (VS) machines. To this end, acoustic measurements of the noise radiated by a dewatering VS were conducted at the Pittsburgh Research Laboratory (PRL) using microphone phased-array technology. These measurements allowed for the identification of the screen as the dominant source in the 250 Hz 1/3-octave band. The sidewalls are the major contributors in the 315 and 400 Hz bands, whereas the eccentric mechanisms and the electric motor are the dominant sources in the 800 and 1,000 Hz bands, respectively.

Jan 1, 2009

By D. P. Desmond

The U.S. Bureau of Mines investigated leaching automobile catalysts with sodium cyanide (NaCN) solutions at high temperatures to recover platinum-group metals (PGM). The feed was virgin monolith rejects, used monolith, and used pellet catalysts. Leaching with a 5-pct NaCN solution for 1 h at 160° C dissolved over 97 pct of the PGM in the virgin monolith, over 85 pct of the PGM in the used monolith, and over 90 pct of the PGM in the used pellet catalyst. Over 99.8 pct of the dissolved PGM was recovered as a precipitate by heating the solution to 250° C for 1 h in an autoclave. The cyanide complexes were decomposed, and free cyanide was destroyed.

Jan 1, 2010

By J. B. Littlefield

[Ata. meeting of the Subcommi ttce on Chemical _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of Mnes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a reference method. 'I'ests ~ ere made aJ,so to aScer ain the effici ency of the recently developed midget i;npi gerS..! for collac ing lead dust. For comparative pur-poses, samples collected by tte large impinger wore included.]

Jan 1, 1938

By J. B. Littlefield

[At B. meeting of the Subcommi ttce on Chemica.l _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of \~nes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a r?ference ]

Jan 1, 1938

By C. J. Chindgren

Two air classification systems were built and tested as separatory devices for recovering the nonferrous metal values from shredded automotive nonmagnetic reject scrap. A horizontal air system with a capacity up to 16 tons per hour was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Shredded automobile reject material containing aluminum, copper, and zinc values of about $55 per ton were air-classified in the horizontal elutriator. Ninety-six percent of the metal was recovered in a 74-percent metal concentrate. Tandem operation of both classifiers recovered 92 percent of the metal in an 80-percent concentrate while rejecting 87 percent of the nonmetallics. Heavy media separation of the air-classified concentrate produced an overall recovery of 91 percent of the metal in the form of a 99-percent metal concentrate.

Jan 1, 1971

By F. W. Lane

Some months ago the Bureau of Mines began research of a fundamental character on sulphur in petroleum. In the course of this work, the usual qualitative test for sulphur in organic compounds1 was applied to certain oils that were believed to contain approximately 0.5 percent sulphur. No sulphur was found, and, as a check on the qualitative test, the oils were subjected to quantitative determination of this element by the oxygen-bomb method.2 The sulphur content of the oils ranged from 0.10 per cent to 0.50 per cent. This experience led to further trial of the qualitative test for organic sulphur, both on the oils mentioned above, and on common sulphur-containing organic substances. No difficulty was experienced in detecting the element in the latter, but with the petroleum oils the test, as usually performed, could not be relied upon to detect less than 0.60 per cent of sulphur consistently. The use of mechanically polished pure sheet copper for the detection of free sulphur, hydrogen sulphide, and perhaps other sulphur compounds has been recommended.3

Jan 1, 1927

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By Nar S. Dala1, Xianglin Shi, Val Vallyathan

"Electron spin resonance (ESRJ and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fracture-induced, silicon-based radicals (Si· and SiO·) and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO · radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO, Na;iSeO:y ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotoxicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). From the comparison of hemolysis and ESR results it is deduced that the radicals play little or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell: membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made toward the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanisms underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1990

By H. H. Schrenk

The safe use of a refrigerant or any substance depends on knowledge of its pertinent properties and conditions of use; therefore some of the properties of refrigerants that are related to life, fire, and explosion hazards are discussed herein. These data serve as a basis for suggested control measures in the use· of refrigerants. The properties of refrigerants may be broadly classified into three main groups: (1) Those important for refrigeration, (2) those significant from the standpoint of confining the refrigerant, and (3) those that become important if the refrigerant escapes from the :machine or container. The first group of properties, such as latent heat of vaporization, specific heat of vapor, specific heat of liquid, etc., is not considered to be directly related to safety and is not discussed here. The second group, those properties important in confining the refrigerants, has particular significance because· it relates to "built-in" safety. This group is emphasized because it is believed the soundest procedure in designing equipment is to give due consideration .to both the health and safety hazards likely to be associated with the equipment. Furthermore, the toxicity, fire, and explosion hazards are controlled as long as the refrigerant is confined. Some properties of this group are (1) stability, (2) corrosiveness, (3) boiling point, (4) pressure developed in the system, (5) warning odor or irritation, and (6) ease of detection. The third group includes such properties as toxicity (of compound and decomposition products), irritating action, and explosibility.

Feb 1, 1942

By G. L. Neumann

The Andover-Sulphur Hill iron mines in Sussex County, N. J., have a production record extending over 100 years. The last production recorded was about 1880. These mines produced high-grade ore of two types: Bed ore (hematite) and blue ore (magnetite. Some sulfides (lead, zinc, and copper) were found underlying the iron deposits. Data as to size and grade of these sulfide bodies are very sketchy, Toward. J. Hewitt of Elizabeth, N. J., lessee of the Sulphur Hill mines from 194045, prospected for lead, zinc, and copper. .His Only production was several hundred tons of low-grade iron ore, which was crushed and used as heavy aggregate to make concrete blocks for ship ballast. In October and November 1942 made a magnetic survey of this area and bored six-diamond-drill holes with the dual objective of prospecting for sulfides and testing for extensions of the iron-ore deposits indicated by the magnetic survey. In 1944, an iron-mining company examined this property and diamond-drilled seven holes Between December 1949 and March 1950, the Bureau Of Mines in search of sulfide deposits, bored three additional diamond-drill holes. Two of these were on the Sulphur Hill tract and one on the adjoining Tar Hill tract.

Jan 1, 1952

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By J. W. Paul

Withdrawing timber in coal mines is done for the purpose of inducing the roof to cave in the mined-out areas and thereby relieve stresses in the immediate roof material over the working places adjacent to the breakline of the roof, thus preventing the crushing of the ends of pillars and adding to the safety of those engaged in pillar extraction. A secondary purpose is the recovery of timber for further use either as prop-, crossbars, lagging, sprags or cap pieces. At some mines timber is withdrawn as a precaution against fire which may he of spontaneous origin, because wood always aids a fire of any origin. With some of the power-driven types of machines now in use a greater proportion of mine timber may be recovered, and in mines where pillars are left too narrow for their removal some of the timber in rooms might be salvaged for further use.

Jan 1, 1933

By Harry W. Campbell

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied parts of the 19,747-acre Lower John Day (OR-005-006) and 7,538-acre Thirtymile (OR-005-001) Wilderness Study Areas in order to evaluate their identified mineral resources. The study areas are located in Gilliam and Sherman Counties, OR, about 13 mi west of Condon. The area is underlain by the Miocene-age Columbia River Basalt Group. The Thirtymile study area is inferred to have 790,000 yd3 of subeconomic gold resources averaging 93.8 mg/yd3 gold ($1.21 yd3 at a gold price of $400 per oz) in two river bars. The Lower John Day study area has five river bars with gold occurrences totaling 1.0 million yd3 and averaging 13.5 mg/yd3 ($0.17 yd3) gold. A preliminary mining feasibility estimate suggests gold could be profitably mined in the study areas from placer deposits containing at least $3.83 yd3 in gold content. Stone, sand, and gravel occur in the study areas, but more accessible deposits are closer to regional markets. No mines or prospects are in or near the study areas; however, one lode mining claim, now abandoned, was located in the Thirtymile study area. Oil and gas leases cover both study areas.

Jan 1, 1987

By D. D. Fischer

Recovery and separation of molybdenum and rhenium from a process solution was accomplished by a technique developed by the Federal Bureau of Mines involving a combined solvent extraction and activated carbon adsorption procedure. The processing sequence required treatment of the solution with S02 to reduce the chlorate ion and adjust the pR prior to solvent extraction of molybdenum and rhenium with a tertiary amine. Molybdenum and rhenium were stripped from the organic phase with an NH40H solution, and the strip solution was then passed through activated carbon to preferentially adsorb the rhenium. After washing entrained molybdenum from the column with a brine solution, rhenium was eluted with an MeOH-H20 mixture. The activated carbon was regenerated with water. Molybdenum was recovered as (NH4)6Mo7024 by evaporating the column effluent. Rhenium in the column eluate was reextracted with a tertiary amine, stripped from the organic phase with dilute NH40H, and recovered as NH4Re04 by evaporating the strip solution. The final (NR4)Re04 product contained < 80 ppm impurities. Sodium sulfate was crystallized from the first solvent-extraction raffinate by lowering the solution temperature to 0° C. Precious metals contained in the original process solution were adsorbed onto the activated carbon.

Jan 1, 1975

By Donald O. Capstick

In 1981, U.S. Bureau of Mines personnel conducted a survey of claims and prospects in the Wheeler Ridge RARE II area to determine if mineral resources or potential for resources exists at deposits in the area. Results of Bureau of Mines investigations indicate the area contains no identified mineral deposits. However, the geologic setting at the Round Valley Peak Prospect near the center of the study area is considered to be favorable for the discovery of tungsten resources with associated molybdenum and copper. Tungsten deposits, should they be present, would be expected to occur at depth in tactite at or near the calcareous rock-granite intrusive contact. Sand, gravel, and stone deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 16,200-acre (6,560 ha) Wheeler Ridge study area is 11 mi (18 km) northwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir Wilderness adjoins the study area&apos;s western boundary (fig. 1).

Jan 1, 1983