Search Documents

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By J. Hudy

The performance of six dense-medium washers was evaluated in five preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation; and one plant was equipped with a two-compartment washer effecting two separations in one vessel. The separate secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The two-compartment washer produced a premium anthracite product and a middlings product. The sharpness-of-separation values ranged from good to excellent for the five primary separations and for the secondary separation.

Jan 1, 1968

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By Yael Miron

ANFO blasting agents may undergo an exothermic reaction when they contact warm ore bodies that contain pyrite and its weathering products. The reaction is very fast at temperatures above 80° C. Urea, when present in sufficient amounts, inhibits this reaction at temperatures below 180° C. But urea-ammonium nitrate mixtures are very hygroscopic and, in certain climates, may be difficult to handle in the field. Reaction-inhibiting characteristics of three compounds were reported by the Bureau of Mines in 1979. Recently, the Bureau investigated the reaction-inhibiting qualities of five additional compounds. Mixtures of ANFO, pyrite, weathering product, and prospective inhibitors were slowly heated, under conditions simulating a hot borehole, to determine prospective inhibitor capability at temperatures up to ~175° C. Small-scale thermal tests of the same mixtures were used for verification and clarification of results. Two organic compounds, phthalimide and xanthine, similar in structure to urea, failed to inhibit the reaction. Zinc oxide and calcium carbonate were found inferior to urea, though zinc oxide raised the onset of reaction from 80° C to about 140° C. Only magnesium oxide was found to be similar to urea in its inhibitory ability at temperatures below 175° C. Based on results from analysis of quenched residues, the use of more than 5 wt-pct magnesium oxide is recommended.

Jan 1, 1982

By Edmund S. Leaver

This information circular is written is response to the marry requests for information on the recovery, or reason for poor recovery, of fine gold by the amalgamation process. Checking Gold Content Experience has shown that in many cases error has been made because the true told content of a particular sample or deposit was not known. Fire assays of representative samples give accurate results and should be considered final in determining the gold content.

Jan 1, 1928

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By Kevin Connor

The mineral industry continued to be an almost negligible contributor to the country's economy as the Government continued its 1979 ban on any mineral exploitation for export; a policy initiated at the end of 1979. A national program had been underway since that time to map and inventory all mineral resources so as to permit future exploitation of mineral wealth in the beat interests of the country and its inhabitants. In March 1982, the British Sulphur Corp. Ltd., under contract to the Burundi Government and the International Bank for Reconstruction and Development (World Bank), began a feasibility study of Burundi's phosphate deposits at Matongo-Bandaga for potential commercial exploitation. The 1-year project effort was to define ore reserves, conceptually design mining operations and processing facilities, estimate capital and production cost, and develop a regional market and distribution survey. Work completed during the year comprised geological exploration and reconnaissance and 1,200 meters of core drilling. Reserves in excess of 5 million tons of ore-grade phosphate were estimated available for mining. Rare earth mineralization was associated with the primary apatite. The associated carbonatite within the rock matrix was preliminarily assessed to be of value as a raw material for the manufacture of cement. The contract effort was valued at $1.2 million? Matongo-Bandaga is located approximately 40 kilometers north of the capital city of Bujumbura and alongside one of the country's few paved roads.

Jan 1, 1984

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980

By L. J. Froisland

The Bureau of Mines conducted a 4-year research program at Uravan, Colo., on a 2-1/2-acre reclamation plot on the slope of a uranium tailings pile that had been covered with mine waste rock. The purpose of this study was to determine the effects of plant species, type of irrigation, type of fertilizers, and use of dust control chemicals on plant growth and surface coverage. Best grass coverage, nearly 100 percent with 240 plants per square foot, was developed in a section that was seeded with crested wheatgrass, fertilized with sewage sludge, and sprinkler irrigated. For comparison, a section that had been treated with commercial fertilizers developed 3.1 crested wheatgrass plants per square foot and 24 percent coverage without irrigation, and 8 plants per square foot and 75 percent coverage with irrigation. Results of spraying a dust control chemical were inconclusive. Russian-thistle invaded all test sections and ranged in density from 0.6 to 7.3 plants per square foot.

Jan 1, 1982

By W. P. Diamond, B. M. Bench, C. M. McCulloch

This Bureau of Mines report describes photolineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W - N 15° E, and N 57° W - N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W - N 20°E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W - N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

By Howard C. Turnage, Dana T. Updyke, Wayne C. Muhler

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leaky feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 6, 1980

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

By J. B. Gayle

The Bureau of Mines sole-heated oven has been used for studying coal expansion for some 20 years. During the period before 1940 emphasis was placed on studies of the mechanism of coal expansion and the effects of variations in operating conditions on the results. Since 1940 emphasis has shifted to a survey of the expansion properties of various coking coals. Because additional information concerning a number of unsolved problems in connection with the earlier studies appeared highly desirable, this investigation of the use of sole-heated ovens for studying coal expansion was undertaken. The principal findings, in order of their discussion in the text, may be summarized as follows. 1. Expansion results for binary blends of coking coals exhibit nonadditive behavior, both positive and negative deviations from additive behavior being noted, depending on the particular coals tested. Additive behavior can be achieved, however, either by charging the blend components in separate layers (which indicates that the observed phenomena are not characteristic of the particular expansion oven used) or by testing relatively coarse sizes of coal (which suggests that the effects of crushing on the expansion properties of coking coals may be even more complex than is generally recognized).

Jan 1, 1959

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

By M. E. Tyrrell

The purpose of the work leading to this report was two-fold: (1) To determine the properties of cemented tungsten carbide modified by the addition of one, two, and five percent of titanium diboride, and (2) to compare the properties of these mixtures when sintered, hot-pressed, and flash-welded (resistance-sintered). Minor additions of titanium diboride to mixtures of 94 percent WC and 6 percent Co decrease mechanical strength but increase oxidation resistance in proportion to the amount of the addition. One percent of titanium diboride increased the hardness by 2 Rockwell A units. Hot-pressing produced compacts with the highest density and the best mechanical strength, but losses of cobalt were high and grain growth was pronounced.

Jan 1, 1962