Search Documents

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By J. Chai, Y. Qiang, D. D. Zhang

"In order to control Quaternary loose layer settlement in East China, there are monitoring results based on the 3 water level observation holes and 7 sand layer of fiber Bragg grating (FBG) strain sensor. Un-der the conditions of upper group water injecting to lower group of loose layer, the deformation characteristics of upper, middle and lower group of loose sandy soil layer changing with time and relationship with the water level are studied. The constitutive relation of stress-strain is also studied at different sand layers. Research results show that using water injecting from upper group into lower group of loose layer can ease the loose layer compression deformation. With the water level dropped, in East China soil creep deformation occurred, which accord with viscoelasto plastic model. The deformation of lower sand group has clear later effect and no direct relationship with water level. The results provide an important basis for the study East China stratum settlement model and water management. INTRODUCTION Ground-surface subsidence is a common geological disaster, which has the features of continuous, changing slowly, concealment (Y.P. Yin et al. 2005). Today, due to underground mining and constructions in formation compression, surface subsidence is wide-spread in the world, which is the environmental geological problems in the worldwide that cannot be ignored (Y.Q. Xu et al. 2006, D.L Gallo-way et al. 2000, Qiu, B. et al. 2011). The eastern region of China has generally geological disasters in coal mine geological caused by the thick loose layer settlement like as mine shaft failure. Stratum dehydration consolidation is a major cause of loose layer settlement (H.Y .Liu et al. 2007). A method of water injection using ground water to stable water level is proposed, which can effectively control the loose layer caused by compression settlement(J. Chai et al. 2012&.2013). Accurately knowledge the characteristics of strata deformation is the premise of settlement management (Q.C. He et al. 2006). Previous re-search (J.F. Miu et al. 1996, X.Y. Gu et al.1998, Y. Zhang et al. 2006), mainly studies are focused condition of the city pumping irrigation, de-formation characteristics of middle and up loose layers. On a group of aquifer in East China, the loose layer losing water is caused by coal mining, bottom water drainage and overlying strata water flowing fractured zone hydrophobic induced by mining, which the dehydration conditions have great difference from one to another. The Position of water loss is centralized in bottom aquifer, and the formers of ground subsidence geological environment and settlement mechanism are different. According to the study of stratum settlement, usually the de-formation of sand layer is ignored(C.H. Liu et al. 2004), but few studies show that the sand layer have the plastic deformation, and contains the creep deformation, water content of sand soil may become the main settlement layer (Z.X. Wei, 2002, C.H. Liu et al. 2004)."

Jan 1, 2015

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

By J. Marbeau

In this paper, a geostatistical study of the North Butte roll type uranium deposit is presented. The geostatistical procedure applied takes into account the varying direction of the roll front for reserves calculations. For variogram calculation, the roll front is unfolded thereby allowing estimation of the variogram in directions parallel to and perpendicular to the roll front. Variograms calculated in unfolded space show strong directional anisotropies consistent with the anticipated configuration of the deposit.

Jan 1, 1991

By Fengyu Ren, Kunpeng Yu, Gideon Chitomb, Qiangqiang Gao, Liqiang Ma, Jiangtao Zhai, Ichhuy Ngo

The penetration of rock fragments of overlying strata causes advanced ore dilution during drawing. The results of numerical and physical experiments showed that the proposed numerical simulation was applicable and the microscopic parameters of the model were reliable. The penetration under the variables of particle diameter ratio, density ratio, overlying strata thickness, and particle morphology was clarified. The penetration was quantitatively characterized by the discharge amount and the dilution rate. The experimental results showed that the diameter ratio and density ratio had a significant influence on the penetration. On the irregular shape of particles, the penetration is weakened. The overlying strata thickness had little effect on the penetration. This study could provide a theoretical basis for the full section uniform drawing, avoiding advanced ore dilution and further optimization of recovery rate.

Nov 13, 2023

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By Andrea Biagi, Elisa Comis, Gianluca Bella, Enrico De Panicis, Guido Barbieri, Matteo Giani

The Sotra Link Project is a major infrastructure project in Norway involving the design, construction, financing and maintenance of several underground and surface structures between Sotra island and the city of Bergen, among them 23 tunnel portals, 12.5 km of tunnels and a 900 m long suspension bridge. This paper describes the benefits in applying a Building Information Modelling (BIM) approach to tunnelling, from Early Design to the Detail Design Phase. The BIM application to the Sotra Link Project resulted in several improvements, such as efficient handling of clashes and inconsistencies, deeper understanding of effective design choices (reduction of errors), more efficient communication between designers, enhanced control of project quantities and costs. The advantages of the BIM approach during the ongoing Construction Phase are also explained.

Jun 23, 2024

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By R. J. Roman

Several research groups have spent considerable time investigating coarse ore leaching. Coarse ore leaching includes both heap and dump leaching. The term "heap leaching" will be used in this paper to mean any type of coarse ore leaching. The results of their work are generally in agreement: the progress of leaching can be described by the shrinking core model and its associated mathematics. The shrinking core model is schematically represented in Figure 1. The particle is contacted by the leach solution on its outside surface and the solution migrates inward by filling the pores on the particle. As the solution filling the pores comes in contact with grains of ore mineral the reagent chemically reacts with the ore mineral to solubilize the contained metal. The solubilized metal diffuses outward to the particle surface and is washed away by the leach solution flowing past the particle. The leaching reagent in the particle interior is replenished by the diffusion of reagent from the surface of the particle to the interior of the particle. If the chemical reaction between the leaching reagent and the ore mineral is relatively fast compared to the diffusion rate of the reagent in the solution in the pores of the particle then leaching proceeds from the outside of the particle inward resulting in a "shrinking core" of unreacted ore surrounded by a "leached shell". The rate controlling step in the reaction can initially be a chemical reaction between the reagent and the ore mineral grain, however, once the reaction has proceeded a short period of time diffusion of the leaching reagent through the leached shell will be the slow step and hence the rate controlling step in the production of metal from an ore particle.

Jan 1, 1992

By Huijun Shao, Qiang Liu, Zhengming Yi

The increase of the proportion of high Al2O3 content iron ore fine in iron and steel enterprises has brought about a series of problems such as the increase of the viscosity of blast furnace slag and the difficulty of the separation of slag and iron. In order to solve this problem, the effect of increasing MgO content on the technical and economic index, the cold strength, and metallurgical properties of high basicity and high-alumina sinter was studied through sinter pot test. Nova400NanoSEM field emission scanning electron microscope was used to analyze sinter microstructure. The experimental results show that when the MgO content fraction in the sinter with high basicity and high aluminum increases from 1.72 to 2.49%, the vertical sintering speed decreases by 4.38mm/min, the utilization coefficient decreases by 0.51t/(m2 h), and the low-temperature reduction degradation index increases by 6.7%. When MgO content in sinter is 2.11%, drum index and reducibility index are the highest, reaching 61.93% and 86.39% respectively. Mg2+ is mainly solid dissolved in the magnetite lattice and replaces Fe2+, up to 3.64%. The generated magnesie-containing magnetite inhibits the phase transition from Fe3O4 to Fe2O3 oxidation process in the sinter cooling process, which reduces the generation of secondary hematite and is conducive to improving the low-temperature reduction degradation performance of sinter.

Jul 4, 2021

By Paul A. Rittenhouse

First of all, I want to thank John Dunlap for asking me to this AIME meeting in Denver. I was first introduced to Denver and The Rocky Mountains more than ten years ago and immediately decided it was one of the most attractive spots in the world. I've come back many times since and still welcome any opportunity to return, even if it means I have to prepare and give a paper on potash. When John Dunlap gave me this assignment, he told me that the program would include papers on the geology of potash, papers on new discovered potash deposits and new mines and asked me to discuss potash from the commercial point of view. He also asked me to include a supply/demand outlook for potash. However, one thing he did not mention was "how far into the future he wanted me to look" and it seems to me the time element is a crucial factor to you who are both geologists and miners as well as to me. In your case, you have to look far enough into the future to give you time to explore, find, evaluate, develop, and bring into production a commercial deposit. My mining associates and friends don't agree on how long that takes but it's probably somewhere in the range of eight to fifteen years. But, they all agree on one thing and that is that the time required is continually getting longer. Now my time problem is just the opposite. It is "relatively" easy, and I stress relatively, to identify and evaluate the importance of the various factors that impact on both the supply of and demand for a commodity such as potash if the time period is today. It gets a little tough if one has to project into tomorrow or next week or next month. And when we start talking in terms of a year, five years or ten or fifteen years, things really get sticky and the old crystal ball becomes mighty cloudy. But we economists and forecasters are not known for our temerity so let me get on with the job at hand and take a look at the world potash supply/demand outlook.

Jan 1, 1978

By Andrew J. Petruska, Austin F. Oltmanns

This work proposes a capacitive load cell for conical picks to enable underground continuous mining machine operators to perform their roles away from known hazardous regions near the machine. The load cell is embedded in commercially available flexible printed circuit board, integrates with the target tooling, and demonstrates in situ force sensing of vibration signatures for continuous mining cutting tools. Changes in material constitution, tool mass, and tool geometry cause modal variations in vibrational response measurable with force sensors at the cutting interface. Time-series measurements are captured during rock cutting tests using a linear cutting machine. These measurements are segmented into small windows, less than 0.25 s, and are preprocessed using the fast Fourier transform, which highlights the modal variations. The transformed measurements are then classified into different material and wear categories using support-vector machines with the radial basis function kernel. Different normalization schemes and Fourier transform methods are tested for signal preprocessing. Results show that the power spectral density measurements with normally distributed coefficients give good results for material classification, while the normalized time-domain measurements give better results for wear classification. Under laboratory conditions, this technique is shown to classify material and wear categories with F1 score above 0.85 out of 1.0 for our experiment. This technology could be used to assist operators in assessing material and wear conditions from a safer distance. It has applications in the coal mining industry as well as other applications which use conical picks such as road milling.

Mar 25, 2023

By J. P. Gliddon

Since 1980 a number of significant changes have been introduced at Palabora in an effort to off-set the effects of reduced product price and increased unit cost of inputs. These changes and improvements include major equipment rationalization programs, the introduction of trolley assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation and their contribution to cost reduction and improved productivity at Palabora are considered.

Jan 1, 1987

By R. E. Turner

Hamersley Iron Pty. Limited, one of the world's largest iron ore producers, operates a 3.0 million tonne per year pelletizing facility at Dampier in Western Australia. The plant produces pellets for the export market using a blend of natural hematite fines from the Company's two mines at Tom Price and Paraburdoo. Processing includes fluidised-bed drying of the ore feed, open circuit dry grinding, disc balling and pellet induration in a travelling grate furnace of Dravo-Lurgi design.

Jan 1, 1980

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By John B. Gustavson

The mineral deposits found in carbonate facies rocks of sedimentary basins include deposits comprised of the country rock itself such as limestone for chemical uses, dolomite for road aggregate, and a variety of other industrial uses of the sedimentary rock. Exploration for new reserves is generally conducted on basis of outcrop investigation, subsurface drilling, and facies change studies while geophysics and geochemistry are not applied. In contrast, rapid development has taken place in the application of both geophysical and geochemical techniques in exploration for stratiform deposits of zinc, lead, barite, and fluorite deposits. This paper will present case histories and show illustrations from such work in the Mid-Continent region. The Metals Division of International Oil & Gas, Inc. has gathered this experience through work over the last three years along the southern margin of the Eastern Interior platform focusing on the states of Arkansas and Tennessee. The exploration work was conducted partially for the Company's own account, partially in joint exploration ventures with mining companies including International Mogul Mines, Ltd., a Canadian company; Bear Creek Mining Company, a subsidiary of Kennecott Copper Corporation; the Mining Division of W. R. Grace and Company, and Boliden-Preussag Exploration, a Swedish-German partnership. We wish to take this opportunity to thank our venture partners for allowing presentation of the various sections of this paper.

Jan 1, 1976