Search Documents

By F. A. Baczek

The Electroslurry TM electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes: The dust is processed through several stages consisting of leaching, copper precipitation, Electroslurry TM electrowinning and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1980

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By A. P. Wickland

The characteristic problems related to drilling a hole for evaluation of an orebody are generally quite similar, whether we're drilling a core hole, or a hole to obtain chip samples. The basic objective in each case is fundamentally an economic factor; to produce the maximum amount of usable information per hole at a reasonable footage price. The success of the drilled hole depends largely upon the amount of investigation and research spent on the prospective area and the ability to forecast the capable personnel needed plus the right kind of drills, ancillary equipment such as bits, muds and various additives necessary to make the drilling program successful. The driller is confronted with a wide variation of drilling problems due to the nature of subsurface conditions. Some of these problems are: overburden, which may consist of clays; sand; boulders; or glacial till. These surface conditions may exist up to 2,000 feet in depth and upon reaching bedrock, formations may consist of swelling shales, broken sandstones, and every conceivable rock-type, coupled with every known structural problem such as dips, faults, folds, etc., and to this added extras such as permafrost and/or ground water problems combine to increase the necessity why an understanding of the problems along with the proper reaction of the driller plus the formula to compensate for ground conditions is necessary to complete a drill hole. Since most geologists are familiar with diamond core drilling techniques, I would like to discuss other methods used in evaluating ore deposits.

Jan 1, 1973

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

"One of the major issues that the Rare Earth Elements Mining Industry has to deal with is the legislation vacuum that exists in many countries around the world. Among these, are countries which have long history and tradition in mining. In many cases the lack of direct legislation for REE mine management as well as for other potentially polluting industries can be a barrier to sustainable development. Moreover, the case of lax legislation in China has led to environmental pollution problems and extended smuggling of rare earth elements. This paper looks into the current regulatory status on the mining of REEs, identifies the loopholes and suggests some elements for a new global legislation framework for sustainable development in the REE mining industry. The setting of this regulatory framework will be in line with the present and future challenges of the rare earths market as well as with the policy strategies that are defined internationally. The aim of such a legislative framework will be to strengthen the global rare earth elements supply chain, appease social concerns and ensure the preservation and conservation of the environment. INTRODUCTION The general public received their first introduction to rare earth elements (REEs) in 2010, when the previously inconspicuous commodities became the subjects of front-page headlines. It was when China created a furore in global high-tech markets after imposing an embargo on Japan following a minor marine dispute (Barakos et al. 2015b). Soon enough the Chinese embargo was extended on REE export restrictions all over the world and thus aroused concerns to many countries over potential supply disruptions. The world had suddenly realized that these wonder materials underpin products that they care about. Governmental and industry executives, policymakers and material scientists voiced concerns and conducted numerous reports stating the situation and the risks of a supply crisis. The price spike of 2011 intensified the crisis and the public turmoil, yet the drama did not last for long as the prices declined significantly in 2012. Nevertheless, the world was nonplussed by the fact that China has the total control of the market with more or less the 90% of the global production. More potential entrants became interested, thus initiating an exploration boom during the recent years that has resulted in a significant increase in known global REE reserves that could have potentials for exploitation."

Jan 1, 2016

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By K. F. Unrug

The concept of bolting mine roofs to prevent roof falls was initiated in the 1950's and was quickly accepted by the mining industry because it was inexpensive, effective and convenient. The principle regarding roof bolting were that: a) the loose and fragmented rocks were suspended from or clamped to more competent surrounding rock and b) generally, by clamping several layers of thin and laminated strata, a more competent monolithic beam is created.

Jan 1, 1991

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine's cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

By M. H. Col

Within the last few years, there have been numerous techno-logical advancements within material handling due, in part, to the introduction of conveying systems and mobile material handling systems to the industry. Although the traditional material handling methods are still commonly used, the introduction of conveyors to the industry has provided companies with some very efficient and economical options. These "new" systems change with the industry to accommodate rigorous demands, ease of operation, and low operating cost requirements. The number of mobile material handling systems utilized in mining operations is increasing, especially in heap leaching applications. Ten years ago, mobile material handling systems like Mobile Stacking Conveyors (MSC) were considered a novelty. There were two (2) MSC's in actual operation and only one of those in a heap leaching application. Today there are numerous proven systems operating at mine sites around the world-La Coipa, Zaldivar, Florida Canyon, Cananea, El Abra, Chuquicamata, and Radomiro Tomic. The popularity of mobile systems is due to the benefits realized by individual projects. As technology advances, so do the concepts behind mobile material handling systems. Implementing self leveling mechanisms, Programmable Logic Controllers, and Global Positioning Systems to control the equipment are just a few of the recent advances that will be discussed in this paper. We will also discuss current proven systems, and touch on what we see as some of the future advances.

Jan 1, 1998

By J. B. Zachwieja, P. E. Richardson, G. W. Walker

The electrochemical nature of mineral-collector interactions and their relationship to flotation have been investigated to develop a better understanding of the factors controlling sulfide mineral beneficiation. Spectrophotometric and electrochemical techniques have been used to examine the reactions occurring on electrodes composed of a bed of bornite particles in the presence and absence of potassium ethylxanthate (KEtX) at a pH of 9.2. The combined techniques showed that KEtX sequentially reacts with bornite by (1) a chemisorption reaction forming ca hydrophobic species between --0.4 and -0.2 V (SCE), (2) an electrochemical oxidation reaction forming cuprous xanthate between -- 0.2 V and the xanthate/ dixanthogen redox potential, and (3) oxidation to dixanthogen when the potential exceeds the reversible value for the xanthate/dixanthogen couple. The flotation response of bornite closely parallels spectrophotometric and electrochemical evidence for adsorption of KEtX by the reactions listed above. The degree of surface oxidation resulting from the formation of iron oxides on the surface dictates the flotation response as evidenced by the fact that oxidized bornite floats at more anodic potentials than unoxidized bornite. The strong correlations between the flotation response, degree of oxidation, and potential indicate that chemisorbed xanthate produces a hydrophobic layer sufficient to float unoxidized bornite, but cuprous xanthate and dixanthogen arc required to float oxidized bornite.

Jan 1, 1988

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By R. L. Grayson, S. B. Bealko, L. L. Chasko, D. W. Alexander

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies, including a fire or explosion, a massive roof collapse, mine inundations or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training.

Jan 1, 2010

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By L. C. Lang

Effective and profitable mining begins with good blasting results. While the importance of sufficient energy to break the rock is recognized, more attention should be paid to the time factor in blasting. Fragmentation, looseness and the shape of the muckpile can be improved and energy levels lowered through the use of proper delays. The long delay is also the most important parameter in establishing stable walls along the final limits of the pit. The time factor in blasting is explained through the rock acceleration process and its practical application is demonstrated by case histories.

Jan 1, 1981

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By James Lett

The role of pre-conditioning in a caving operation has multiple benefits, ranging from assisting with improved caveability, normalising fragmentation and improving draw point hang-up frequency. At Newcrest Mining’s Cadia Operations, both the Ridgeway Deeps block cave the Cadia East Panel Cave have utilised pre-conditioning using hydraulic fracturing. Seismic response data inside and outside the pre-conditioned volume show the benefit of treating the full caving block. Cadia East has further developed pre-conditioning to mitigate developing seismic hazards associated with major structures (fault-slip events) and managing mine-wide seismic hazards in new caving operations where the potential for large damaging seismic events exists due to high stresses and hard competent rockmasses. A case study reviewing the impact of pre-conditioning to mitigate seismic hazard associated with fault slip is presented. Cadia East operation undertook a targeted hydraulic fracturing program and reduced the overall number of large events as an example of the benefits of pre-conditioning. This paper will review the application of Hydraulic Fracturing at Cadia and discuss the geotechnical and seismological parameters of seismic events that occur within and outside of pre-conditioned rockmass volumes to demonstrate the benefits that Hydraulic Fracturing bring to future caving operations.

Apr 26, 2022