Search Documents

By Harold E. Rowen

The listed title of my talk to-day is "MODERN ON STRAND SINTER COOLING". Perhaps it should he ve been "COMPLETION OF SINTERING ON THE STRAND" as the two are synonymous. By the very nature of the DWIGHT-LLOYD SINTERING PROCESS partial cooling on the strand is always present, but not completion of sintering and cooling on the strand. I have mentioned the Dwight-Lloyd process just to be certain the type of sintering under discussion is fully identified because some of the basic mechanisms of sintering occur in various pyro-processing of fines lying in close quiescent contact, such as powdered metals practices, some types of pellet induration, firing of briquets, or other compacts, where the entire bed is brought to, and held at, the high reaction temperatures of sintering. Figure 1, The continuous sintering process as originally conceived consisted of intimately mixing carefully proportioned burdens, placing them in a comparatively thin, draft permeable layer, on a moving grate and igniting the surface while drawing sir through the bedded burden. The moving grate was advanced slowly as the line of burning fuel travelled from the surface to the bottom of the bed and no more fire zone could be seen.

Jan 1, 1973

By Paulo Roberto Pereira

This paper is motivated by the belief that increasing drilling and blasting costs will not necessarily bring about better digging or crushing productivity. As a matter of fact it can be counter productive as the ensuing discussion will show. In the two case studies presented herein when powder factor increased, productivity at a rope shovel and at a primary crusher decreased. Experience has shown that equipment (shovel and primary crusher) productivity increases as the powder factor increases and concurrently operating costs decrease. This is illustrated by Figure 1where the graph shows (assuming drilling costs constant) that for increases in powder factor initially operating costs might fall till a certain point and then they start to go up again. By the same token we need to understand what is the behavior of the operation’s productivity. It seems intuitive productivity goes up for increases in powder factor but when an operation reaches the point of minimum operating cost one could say that productivity reached its maximum. For continuing increases in powder factor can productivity still go up or does it go down? This paper presents two examples where the productivities of a surface coal mine and of a quarry are reduced for increases in powder factor. This indicates that these two operations could be operating to the right of their minimum operating costs and maximum productivity and therefore wasting precious drilling and blasting dollars and resources. Moreover, their productivity is following the red dotted line in Figure 1 and the question becomes can they follow the blue dotted line for increased drilling and blasting costs? The industry owes to itself to determine this minimum operating cost point and what can be done in case that the productivity goes down afterwards despite an increase in drilling and blasting costs. In other words, utilize your drilling and blasting resources correctly. In the two examples that follow single explosive loading strategies make powder factor a valid means of comparing the results of productivity as a function of powder factor. Also, external factors such as equipment operator influence are eliminated due to the long time span considered in the analysis

Jan 1, 2005

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By John M. Ackerman

In the spring of 1988, Freeport-McMoRan Resource Partners Ltd. Partnership, IMC Fertilizer Inc. and Homestake Mining Co., as joint venturers, were awarded the sulphur lease for Main Pass Block 299, lease number OCS-G 91372. This was one of 11 leases awarded to the joint venturers. Following the initial discovery wells in December 1988, delineation drilling confirmed proven sulphur reserves of 68 Mt (67 million long tons). Proven, recoverable oil and gas reserves are 6.2 Mm3 (39.4 million bbl) and 1114 Mm3 (7.2 billion cu ft), respectively. Development of the sulphur mine was given approval as a fast-track project in 1989. The oil and gas reserves were acquired from the original hydrocarbon lessee in 1990 and were also given fast-track status. Fast-track for these projects meant design and engineering would not be complete before construction began. Joint venture The Main Pass Joint Venture is one of 13 joint ventures formed between Freeport and three other companies - IMC Fertilizer, Inc., Felmont Oil Corp., a wholly owned subsidiary of Homestake Mining Co., and Texasgulf Minerals and Metals Co. Felmont has since changed its name to Homestake Sulphur Co. Texasgulf assigned its interests to its parent company. Texasgulf did not participate in the Main Pass 299 joint venture. Joint venture negotiations, anticipating a lease sale in mid-1988, began in December of 1987. This joint venture, the first of its kind, was created to acquire offshore leases, explore, develop and mine sulphur. The Interior Department's Minerals Management Service (MMS) announced a lease sale date of Feb. 24, 1988 on the first business day of 1988. This greatly accelerated the joint venture negotiations. Of the 13 leases the joint ventures bid on, 11 were awarded. Freeport holds its interest in all the leases through its ownership interest in Freeport-McMoRan Resource Partners, Ltd. Partnership. Resource Partners is the operator on all of the leases.

Jan 1, 1992

By Jonathan M. Pachter

Introduction The Bailey mining complex is located in Greene County, PA, in the Talley Run valley. It includes two Pittsburgh No. 8 seam deep mines (Bailey and Bailey No. 2), a coal preparation plant, and two refuse areas. Clean coal is shipped from the complex by way of a 24-km (15-mile) rail spur. It con¬nects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Co. (Consol) began a permitting effort aimed at building the mine. Construction began in Dec. 1981, less than six months after the first application submittal. Clean coal was produced by the Bailey preparation plant in Sept. 1984. Several factors allowed quick permitting at Bailey. Effective project planning, including early formulation of a project planning team, and identification of red flag issues helped. So did innovative responses to environmental questions, and development of environmentally sound project designs. Forming a project planning team Consol management decided that Bailey mine construction had to begin in late 1981. A project permitting team was immediately formed to see that this goal was achieved. Team members included a project manager and personnel from Consol's engineering, environmental, and operating departments. Communications among all team members was crucial in obtaining the various state and Federal environmental permits. All project permitting team members participated in weekly meetings during application preparation. Discussions at these meetings ranged from recent public contacts, to application content, to environmental design considerations. Establishing a project manager was critical to the team's success. The project manager was responsible for seeing that permit acquisition, facility construction, and operation of the mining complex proceeded on schedule. The project manager had the final word, mediated disagreements, and frequently served as project spokesman to the public. Identifying red flag issues Red flag issues are those environmental factors with the most potential for delaying the schedule or stopping the project. The first red flag issue identified was organized local opposition. This opposition had completely derailed a US Soil Conservation Service proposal to build a multipurpose dam on Enlow Fork, a short distance

Jan 9, 1985

By L. B. Anderson, G. A. Carmody

We wish to comment on the paper by G.W. Heunisch (MINING ENGINEERING, January 1987), which raised several important points regarding treatment of acidic waste waters. This paper confirms, in part, tests carried out by Allyn Corp. Allyn is the manufacturer of the proprietary product Alka-Ment, one of the materials that Heunisch tested. The first point is the extreme sensitivity of the sedimentation rate on the nature of the treatment material used. This apparently results from differences in nucleation of the metal hydroxides, and is consistently higher for Alka-Ment. This decreased sludge volume is also observed when Alka-Ment is combined with flocculants, such as organic polymers (see Table 1). Our second point is to emphasize that Heunisch's work shows how dependent the sludge volume is on pH. It is common practice to overtreat AMD by raising pH to 9 or 10. This practice, in addition to being wasteful of material, actually decreases the density of the resulting sludge, probably by creating charged particles that do not readily coalesce. When treating with Alka-Ment, we recommend that the treatment be monitored by testing both pH and dissolved iron. For both tests, it is important to allow adequate time to elapse between treatment and measurement, so that dissolution of alkali, aerobic oxidation of iron, and precipitation of the metal hydroxides are nearly complete. Our tests have indicated that from 30 minutes to one hour is commonly required. Only in this way can a minimum pH be attained, with adequate treatment, denser sludge, and lower treatment rates achieved. Thirdly, Heunisch correctly recognizes that ASTM titration of Alka-Ment does not reflect the true treatment value available in a unit of Alka-Ment. Our work at Allyn indicates this is a most important consideration when evaluating various materials for the treatment of acidic waste waters. While we were unaware of Mr. Heunisch's work, we welcome comparisons between Alka-Ment and any competitive products readily available for field use. Allyn has hundreds of hours of laboratory and field data we are ready to share with interested parties treating acidic waste water.

Jan 1, 1988

By Yi Luo

A massive roof fall occurred in a small room-and-pillar coal mine. The roof falls occurred under a barrier pillar in a closed coal mine located a short distance above the active mine. The extensive fractures connected the active mine with the old mine, turning them into a “combined mine.” Since completely sealing off the roof fall area is prohibitively expensive for the mine, ventilating the connected old mine became the only option. A comprehensive investigation was conducted to understand the atmospheric condition in the old mine and to find an efficient way to ventilate the “combined mine.” A set of studies involving geology, gas content, pillar stability and mine subsidence were performed to explore whether the closed mine is filled with an explosive air-methane mixture. The air quantity measurement data were used to determine the resistance of the air path formed through the fractured zone. Observations and measurements made from a tour to the underground and mine surface enabled the formulation of simple but effective ways to ventilate the old mine. The ventilation network analysis also suggested methods of control, so that sufficient ventilation air can be directed to the two parts of the old mine.

Jan 1, 2010

By F. Seymour

A dynamic programming algorithm is presented that takes a series of nested phases, a fixed mining rate schedule, a fixed plant production capacity schedule, and finds the mining and cutoff grade sequence that maximizes the Net Present Value. This tool allows the Mining Engineer to quickly look at project sensitivity to various production capacities, commodity prices, and costs. A description of the algorithm is given along with examples of how it has been used at Newmont.

Jan 1, 1995

By Andrzej Wala, Henry P. Cole, Perry David Passaro

Cognitive representations and misconceptions of flow through circuits is an area which has received little attention from science educators, cognitive psychologists, or accident investigators. Misconceptions are also called Aristotelian thinking. They involve a person using primitive unscientific ways of reasoning to make decisions about events (Piaget, 1929; Nussbaum & Novick, 1982; McCloskey, 1983). The use of such primitive concepts leads to errors in reasoning about scientific and technical problems. The existence of misconceptions is well documented among children, adolescents, and adults involved in learning science concepts (Piaget, 1929; Cole & Raven, 1969; Clement, 1982; Mistrell, 1982; McDermott, 1984; Richardson, 1987). Concepts of flow through circuits are important because miners' conceptual errors about these aspects may be, in part, responsible for two fatal mine disasters. On at least two separate occasions, methane gas explosions occurred in underground mines when separate ventilation systems were connected (Elam, Fuller, Carter, Cavanaugh, Fesak & Painter, 1983; Fesak & Cavanaugh, 1984). A review of these disasters indicates that conceptual errors made by miners may have resulted in the accidents (Cole, Wala, Haley, & Vaught, 1987). In this study, co-author Andrzej Wala, stated that his research had "identified conceptual errors that may have caused the miners in these disasters to make fatal mistakes" (Cole et al. 1987), p. 167. Further exploration of these conceptual errors by Wala has led to the hypothesis that misconceptions of basic aspects of flow distribution changes in mine ventilation circuits, are at least, in part, responsible for some mine disasters caused by errors in ventilation systems (Wala & Cole, 1987). Why should these conceptual errors occur? Ausubel (1963) suggested that students come to a new area of study with their own conceptions or preconceptions about how a process operates. Furthermore, these preconceptions may be in conflict with the empirical data from the discipline. In such cases, learning becomes a process in which new concepts must displace or be re-molded from stable concepts that the student has constructed over many years (Clement, 1982). Given the existing research with misconceptions and the work of Wala and Cole (1987), it was hypothesized that experienced miners; either working miners, students of mining engineering, or professional mining engineers, harbored misconceptions about the formal or conceptual aspects of mine ventilation circuits. The misconceptions hypothesized to exist involved flow distribution changes in complex mine ventilation circuits; specifically, how does flow distribution change when a ventilation circuit pathway is altered? Given this information, the following research questions were proposed. Research Questions 1. Do experienced miners and mining engineers harbor misconceptions about mine ventilation systems? This question was addressed by: A. The administration of the Cutthrough Ventilation Arrangements (CVA) exercise that measures subjects' performance level when making decisions about major ventilation changes when connecting two mine sections;

Jan 1, 1989

By R. W. Lankston

Uranium mill tailings disposal facilities present unique problems with respect to siting, design, and long-term stability because their contents remain potentially hazardous for 100,000 years. Dawn Mining Company, operator of a uranium mill in Washington, undertook geological and geophysical studies relative to planned expansion of existing disposal facilities. Seismic refraction and reflection, resistivity, and ground magnetics data were integrated with limited drill data to determine the configuration of Quaternary sediments and the underlying basaltic and granitic bedrock. Analysis of multiple reflections and magnet modelling on a micro-computer with CRT graphics added detail to the interpretation.

Jan 1, 1980

By Jamal Rostami

Continuous miners (CM) are the most popular underground mining machinery in soft rock mining, playing a dominant role in the production of minerals ranging from coal to evaporites while finding increasing use in salt and potash mines. Along with the ongoing technological advancements in the mining industry and the underground equipment, new generation of CMs offer several new features that are designed to enhance their operational capabilities and production rate. In addition to new bits and bit holders, one of the areas of improvement is the cutterhead design through computer modeling and simulation based on the full scale cutting tests. This paper discusses the state-of the-art CM technology and development of the computer models for design analysis and performance estimation of CMs. The general approach used in the modeling, along with the results of field trials for several projects will be presented.

Jan 1, 1998

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

By N. T. Cowper

Slurry viscosity ultimately affects the majority of mineral extraction processes. However, to date its role has been disguised because mineral processing equipment has been conservatively designed to operate at minimal slurry viscosity. With most ores this still meant acceptable solids concentration was achieved. However, with the advent of treatment of weathered ores the resulting higher slurry viscosity (rheology) has meant solids concentration has had to be reduced, often to unacceptable levels. To permit operation at higher solids concentration chemical dispersants are employed. These dispersants are expensive and their addition should be controlled. Slurry Systems Pty Limited (SSPL) has developed an On-Line Viscometer to monitor and control slurry viscosity, whether by controlling water addition or by controlling dispersant addition. Using this instrument the slurry rheology can be controlled at the optimum level, maximizing solids throughput, and minimizing water, reagent, and dispersant addition. This paper discusses rheology of typical mineral slurries, the relationship between slurry rheology and percent solids in a slurry, and the need for rheological control in mineral processing. The effects of rheology on various process steps, and the use of dispersants are reviewed. The paper concludes with summarizing actual case histories and cost impact of Theological control.

Jan 1, 1992

By Ronald J. Vance

One of the key elements of change in the mining industry has been the ever-increasing integration and coordination of previously highly segregated business disciplines, the extent to which the marketing and finance functions have evolved and merged within the mining industry. If one listens to the language of mine product marketers today, one hears terms like contango, backwardation, forwards, options, min/max, synthetics, swaptions, caps, collars, FRA's, spot deferreds, double bottom, head and shoulders. The list is endless and a glossary may be out-of-date even before the ink is dry. No longer can a marketer of mine products get through the day and, more importantly, keep his or her job merely by reciting statistics on supply, demand, prices and the jargon of quotational periods, delivery and payment terms. Walk into the office of any marketing department today, and computer terminals spewing on-line market prices and instantaneous news retrieval command the attention of all who enter. Traditionally, mining companies, particularly those in North America, took a passive view toward marketing their products and an even more passive view toward management of price risk. The typical, albeit simplified, gold producer of the 1970s and early 1980s spent all of its energy exploring, delineating, developing and producing a product that was placed by the mine gate. Like magic, anonymous buyers took it away and left piles of dollars in its place. No fuss, no muss and nothing to get in the way of more exploring, delineating, producing etc. The typical copper producer, meanwhile, was slightly more creative. Copper producers still spent most of their energy exploring, producing etc., but they at least acknowledged the identity of their customers. Many even went so far as to fabricate finished mine products into shapes and sizes that their ultimate customer needed. Wire, cable, sheet and extrusions were all in forms ready to be purchased by power companies, motor manufacturers and telephone companies. But, while production and costs steadily increased, research and development into new expanding markets was funded by little more than lip service. Competitors and competitive products steadily eroded market share and realized prices. The now-famous Business Week magazine cover that proclaimed "The Death of Mining" was an imminent reality.

Jan 1, 1993

By Harald F. Solberg

A preliminary study of the performance of a 4-inch Krebs cyclone at near rope conditions and different feed slurry temperatures was completed. Results suggest that temperature influences the x50c size which, in turn, did not depend upon spigot diameter. The bypass correction to a reduced efficiency equation incorporating the concept of a critical size xo was a function of fractional water recovery to underflow and may depend on feed size and feed percent solids. Further experimentation is required to develop an accurate model at near rope conditions.

Jan 1, 1981

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

The US Bureau of Mines' dictionary of mining terms defines productivity as "the efficiency with which economic resources (men, material, and machines) are employed to produce goods and services." Or, the relationship between the physical outputs and the physical inputs used to produce those outputs. As demand for mine materials dropped, mining companies and equipment manufacturers discovered that ratios between the inputs and the final products were disproportionate to the profits realized. Some companies are fighting for survival. The US, while still the most productive country in the world in absolute terms, is looking over its shoulder as other industrialized nations continue to exceed its yearly productive growth rate. According to John Belcher, Jr., of the American Productivity Center in Houston, TX, the US has seen a steady decrease in productivity growth since the mid-1960s. During the post World War II period, the US labor productivity growth rate was 3.2% annually. The slowdown began in 1965 and by the mid-1970s, the country's annual growth rate was 1%. By 1978, labor productivity growth ceased to gain at all and from 1978 to 1980 a 2% decline occurred. Solutions to the productivity decrease are increasing product prices or improving productivity. By increasing prices, though, the producer runs the risk of pricing himself out of the competitive market. To maintain an acceptable profit level, prices must increase proportionately higher than required to offset production cost increases, Belcher says. Many companies are turning to in-house productivity improvement programs as an answer to increased costs and declining profits. These programs are geared toward management commitment and employee awareness of what productivity means. Companies are finding ways of measuring productivity levels in financial reporting, budgeting, and planning. Organizational teams have been formed to coordinate activities and oversee product management, and improve productivity of materials and capital investments. This special issue of Mining Engineering examines productivity in the mining industry. First, there are articles about various, and different, factors that affect productivity in each of ME's five main readership areas - exploration, mining, processing, coal, and industrial minerals. There is also a look at mining industry productivity from the manufacturer's view. The next section of this special issue is devoted to some topics that affect all areas and sectors of mining: research, management practices, computers, maintenance, and energy management. Then follows case studies in exploration, coal, and iron and steel. These studies provide examples of practices and strategies used by companies and operations to boost productivity.

Jan 11, 1983

By Lee R. Martin, Michael R. Taber

Bird Balls™, the latest development in the ongoing battle at mine sites across North America, help to eliminate accidental avian mortality caused by birds ingesting cyanide leachate. Bird Balls™ are a 4-inch sphere made of high-density polyeth­ ylene (HDPE). They weigh 40 grams and are black in color to provide optimum life in UV intense environments. A floating blanket of bird balls totally excludes birds from a liquid surface. Federal agencies that enforce the Migratory Bird Treaty Act do not specify how to keep migratory birds out of leachate basins. Some state agencies, however, specify that a physical barrier must be in place to exclude migratory birds if cyanide levels are high enough to cause mortality. Industry standards for protecting waterfowl now include Bird Balls™ as well as net­ting, detoxification, and heap leach systems designed in such a manner that no exposed solution ponds or channels exist. Hazing is no longer an option. A bold statement to make? Perhaps, but W. R. Jeffress (1990) covers the subject well when he stated that, "Hazing techniques as a whole have not been effective in excluding waterfowl or other species of wildlife from toxic heap leach solution ponds or tailings impoundments. Research and devel­opment of the new 'Star Wars' hazing techniques, such as laser netting and radar systems, are interesting concepts and will pos­sibly offer an alternative to total physical exclusion or neutral­ization in the future. All of these methods are going to have to be thoroughly tested." For those who may want further docu­mentation, we have included a special reference section cover­ing hazing. R. J. Hallock (1990) stated that, "The Fish and Wildlife Service is particularly interested in migratory birds. In fact, a large portion of our effort, nationwide, is focused on migratory birds. Bird habitats are managed directly through the National Wildlife Refuge System and indirectly through other agency programs. We also have a responsibility to protect birds under the Migratory Bird Treaty Act. Most birds attracted to mine ponds are covered under this Act. The only migratory birds not protected under the Migratory Bird Treaty Act are English Sparrows, Starlings, and Pigeons. Since this is a treaty with five nations, the concept of acceptable losses does not apply. It is not a negotiable situation. There are a few exceptions noted in the Act, including prescribed hunting of selected waterfowl, scien­tific collection, and game bird farming. There is no exception for the loss of migratory birds exposed to solutions of cyanide."

Jan 1, 1996