Search Documents

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

By S. Gupta

Froth flotation is a process commonly employed for the selective separation of phosphate from unwanted mineral. Column flotation has become widely accepted in the mineral processing industry, including phosphate industries, due to its ability to improve selectivity, lower operating cost, lower capital cost, and superior control. In this work, a hybrid model is developed that combines a physicochemical model with artificial neural networks. The physicochemical model is based on axial dispersion with first order collection rates. A new approach, in which both frankolite (the desired mineral containing phosphate) and gangue (undesired product) are modeled, enables prediction of grade of the recovered product. Thus, two basic parameters are required in this model: flotation rate constants for frankolite and gangue. Artificial neural networks are used to predict flotation rate constants. The model also takes into account the particle size distribution and predicts grade and recovery for each particle size range. The model then combines grade and recovery for each particle size range to determine the overall grade and recovery of the column. The model is validated against laboratory column data.

Jan 1, 1998

By John Oskam

In 1873 Barton tines Corporation mining Garnets for Abrasives. From providing bulk Garnet Concentrate the technology has advanced to the sizing and classification of micron sized particles utilizing a Barton process. Processing of Garnet involves extensive quality control at all steps, first to insure product purity and secondly to insure the correct size range. Barton Mines produces about 30 different sizes of Garnet products to lead the world in the manufacture of technical abrasive Garnet. This paper will examine the present technology of Garnet Abrasive Manufacture and the specification to which the sizes are produced as well as some of the markets served.

Jan 1, 1980

By J. Hanna, I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pHs without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35% to 38% P2O5, 0.8% to 1% MgO) with high recoveries (80% to 85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P2O5 and 0.8% MgO, with a P2O5 recovery of 76%. A concentrate obtained from the western US phosphate ore from Utah assayed 30% P2O5 and about 1% MgO, with a P2O5 recovery of 89%.

Jan 1, 1988

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By J. F. Hunt

[THE AUTHOR DESCRIBES THE ACTUAL PROCESSING OF THE GOVERNMENT STOCK¬PILE OF CHROMIFEROUS SANDS. LOCATED AT COQUILLE. OREGON, DURING 1955 AND 1956. A GENERAL HISTORY OF THE STOCKPILE IS GIVEN, ALONG WITH A BACKGROUND OF THE GEOLOGY AND ORIGIN OF THESE SANDS. THE FLOW SHEET USED IN THIS OPERAT ION IS OUTLINED IN DETAIL, AND THE MINERALS WON FROM THE STOCKPILE BY HIGH TENSION AND MAGNETIC PROCESSING ARE DISCUSSED AS TO THEIR PURITY AND SALEABILITY. AMONG THESE MINERALS ARE CHROMITE, ILMENITE, MAGNETITE, ZIRCON, GARNET, RUTILE, MONAZITE, GOLD, AND PLATINUM. PLANNED POST-STOCKPILE OPERATIONS ON THE PRESENT BEACH DEPOSITS ARE DISCUSSED. THESE OPERATIONS WOULD HAVE BEEN CARRIEDOUT TO SET UP A' CONTINUOUS INTEGRATED MINING AND BENEFICIATION PROJECT, EXCEPT FOR UNFORESEEN CIRCUMSTANCES WHICH DICTATED THE CLOSING OF THE OPERTIONS AT THE EXHAUSTION OF THE GOVERNMENT STOCKPILE. THE PAPER IS ILLUSTRATED WITH MAPS, FLOW SHEETS, CHARTS; AND PHOTOGRAPHS OF STOCKPILE, PLANT, AND EQUIPMENT.]

Jan 1, 1964

By Harry M. Parker

Exploration for sandstone-type uranium ore bodies which will be exploited using underground mining techniques is usually executed in sequential fashion. Geostatistical methods can be used at the earliest exploration stages to design drilling programs which have a high probability of success in the location and delineation of mineable ore-grade mineralization, should such mineralization exist. In succeeding development stages, geostatistics may be used to outline and define the potential grade of reserves and to apply confidence limits on the grade estimation. Delineation of mineable reserves for mine planning requires extensive development drilling; using such drilling data geostatistical methods may be used to minimize the drilling needed to achieve a desired level of confidence in the calculation of mineable uranium ore grade and tonnage. Because sandstone-type uranium deposits tend to be pod-shaped and are generally aligned along a mineralized trend, this paper proposes a geostatistical method of calculating uranium ore reserves which accounts for this fact and predicts the area within a trend which is underlain by ore. This method uses an indicator value; that is, drill holes which contain mineable ore-grade intercepts are coded as 1, those that do not are coded 0. The indicator may be kriged over the mineralized trend to obtain an estimate of the area underlain by ore. The thickness and grade-thickness may be kriged, and the average ore grade may then be obtained by dividing grade-thickness by thickness, as is conventional for stratabound deposits. The mean grade is then multiplied by the kriged mean thickness to obtain an estimate of the volume, and thence tonnage, of mineable ore within the trend.

Jan 1, 1979

By Greg Bold, Mahmood Khwaja, Yuannian (Jerry) Wan, Michael S. Schultz, William Simcoe

Beaver Creek Clean River Project will satisfy the consent decree requirements by capturing and treating combined sewage overflows. The project consists of, approximately, 2,700 feet of 30-inch trenchless pipe installation, a new screening/disinfecting facility, an expansion of an existing diversion structure, and a 72-inch internal diameter, 530-foot long mined tunnel. The tunnel portions are being progressed as early release packages. This paper presents the geotechnical exploration program and the subsurface conditions encountered; interpretation of the geotechnical conditions; and, approach to developing stand-alone packages for the tunnels to mitigate construction and schedule risks and continue to advance the project.

Jun 13, 2021

By George R. Mitchell

It is a common observation that objects having, different; temperatures exchange energy by radiative transfer. The quantity of radiant energy emitted by an object is a definite function of its temperature. Therefore, a measurement of emitted radiation, by means of a calibrated radiometric instrument, provides a temperature measurement without contacting the emitting object. The physical laws describing radiant energy transfer and their application to remote temperature measurement form the substance of this paper. The energy radiated by bodies having temperatures up to 4000°C is largely in the infrared spectral region. The infrared spectral region is that part of the electro-magnetic spectrum having wavelengths longer than visible light and extending to the microwave region. The wave-lengths range from 0.7 micron (1 micron = 10-4 cm) to 1000 microns. In general, infrared radiometry deals, with the methods of measuring energy flux in the 1 to 15 micron region of the infrared spectrum.

Jan 1, 1960

By R. D. Bartlett

Large open pit mines in desert climates, such as the Phelps Dodge Morenci copper mine in Arizona, can create groundwater cones-of-depression of considerable size and :ability. The hydraulic containment provided by the groundwater depression prevents migration of process solutions into the surrounding regional aquifer. Copper leach operations that fall within the groundwater depression may not require costly lining if passive containment can be demonstrated. An approach is presented in this paper that was successfully used to demonstrate passive containment. The approach includes a combination of groundwater modeling and a water balance analysis of leaching operations failing within or immediately near the open pit.

Jan 1, 1999

By Miroslav Cervenka

The Coal, characterized by coal quality parameters as for example, ash content (Ad), moisture (Wrt), heat content (Qr1), sulphur content (Sd) and other parameters is still in many countries the basic source of energy. Energy is life, especially in modern society, where the demand for ecologically clean energy is very high; and therefore, there is great importance in effective coal utilization Direct utilization - burning of coal for energy generation, is still one of the most effective methods. In most cases, it is one of the cheapest energy transformation methods in spite of the fact that this energy transformation is connected with the deterioration of our surroundings. Deterioration can be substantially reduced if the burning of coal at power stations, heat power stations and other coal consumers is optimized. That means the burning is done in steam boilers, the technical state of which is very good; the coal has minimimum .variations with respect to the projected values; and the burning process is controlled and checked not only from a regulation point-of-view but also from an ecological point-of-view. The instrumentation capable of measuring the characteristic coal quality parameters in real time exists and it forms the basic assumption for the work our research team has made. The proper application of this instrumentation is able to provide information for burning process optimalization. It is the main topic of this paper, which is the compilation of the information on our work -made during the last five years. The whole information is based on practical experience and applied systems in Czechoslovakia in the mines and power engineering industry. See [Cervenka, 1989]

Jan 1, 1992

By V. C. Lo

The major cost in comminution is energy consumption, which can be as high as 50 percent of the operating cost. Improvements in plant operations have resulted in up to a 15-percent reduction in energy usage (kwh/t). These improvements have been made through optimization of grinding efficiency and use of expert model-based control systems. Optimization involves the determination of the levels of the critical operating conditions that result in the most efficient breakage of ore in the mill. These optimal levels are identified through plant/laboratory testwork and computer simulation using advanced process models. Model-based expert control achieves the maximum performance from the grinding circuit by identifying the characteristics of the ore in the mill with an optimal on-line estimator. Using this information, the control system dynamically determines the operating point that will yield the optimal performance. Two industrial applications of grinding circuit optimization and model-based control are presented to demonstrate the power of this new technology.

Jan 1, 1995

By A. D. Pernichele

Four types of slope failures in waste dumps are recognized; debris flow, foundation failure, edge slump and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is considered to be the most dangerous because of its explosive mode of failure and lack of forewarning. The December failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicated that the impounded water was due to a zonal accumulation of Jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1971

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth's surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country's primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By Joseph B. Gillenwater

Miss Gertrude Carey lived next to us in Martinsburg, West Virginia for several years. She was a retired school teacher. She was also a cousin to Messers Dan and Joe Baker who owned and operated Standard Lime and Stone Company, a predecessor of Martin Marietta Corporation. She-was well acquainted with the Baker family and their history. Here is one of the legends she told my wife, Jean, and me. The Bakers were originally Tanners. They had a tannery near Frederick, Maryland. There were several boys in the family and when they were grown each man had specified responsibilities. Will Baker was assigned the duty of locating, buying, and transporting tanbark and lime. As he traveled through Maryland, Virginia, Pennsylvania, and West Virginia to locate and buy tanbark, he also talked the farmers out of some pieces of lime, which the farmers had produced in holes dug and filled with layers of limestone and wood. Will Baker took the lime and soaked a piece of hide in the milk of lime. If the lime did not spot the hide, Will Baker would get the farmer to burn some lime for him, and further tests would be made. If these tests were good - the Bakers bought the land. They eventually discovered that the limestone that would make lime that wouldn't spot the hide would also be suitable for producing steel. They began producing lime just outside Harpers Ferry, West Virginia in pots and upright kilns. That stone too small for the kilns was just perfect for railroad ballast. Now you know how "Baltimore Blue Bloods" got together!!

Jan 1, 1979

By M. S. Celik

Adsorption of sodium dodecylsulfonate (SDS) and dodecylaminium hydrochloride (DAH) on Buller seam coal, New Zealand, have been studied. Both surfactants adsorb effectively on the coal below pH 8, and the adsorption isotherms established at pH 4 are essentially the same at lower concentrations. These findings suggest that the adsorption of these two ionic surfactants on coal is controlled by a hydrophobic bonding mechanism. However, the results of calorimetric studies suggest that coulombic attraction also plays a part in the adsorption mechanisms. It has also been found that both the SDS and DAH adsorbed in the first monolayer are not removed by lowering the surfactant concentrations in the bulk solution.

Jan 1, 1993

By James A. L. White

Although the quantity of native sulphur associated with volcanism is large, production from such deposits represents only a very small percentage of total world production, This paper describes the location of the known deposits, the typical geology of these deposits and the nature of the sulphur mineralization. Methods of treatment are discussed and some comments are offered on the economic position of these occurences in world sulphur markets.

Jan 1, 1967

By S. E. Knalafalla

The availability of a fluid whose gross behavior sharply changes in a magnetic field without affecting its rheologic characteristics has been recently demonstrated. A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum in a continuous fashion. Magnetic levitation forces were created as an antigravity field when the fluid was properly placed in an inhomogeneous magnetic field. Five spherical non¬magnetic objects with densities ranging from 2.70 to 11.35 gram cm ' were made to float or submerge at will in a 0.96-gram cm-3 density fluid placed at vertical magnetic field gradients ranging from 0.2 to I kilooersted cm-1. The magnetic levitation farce in dyne cm-3 was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1972