Search Documents

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By Robert G. Lundguist

REAM is a unique and promising method of rock breaking using high energy, inert projectiles to impart mechanical energy to the rock. This paper describes a demonstration of the application of this new technology to two specific problems in open pit mining: secondary breakage and the scaling of loose material from pit walls. Under previous government contracts, Physics International Company developed the projectile impact method for a large variety of commercial and military rock excavation tasks. A 4 meter (13 foot) diameter by 16.8 meters (55 foot) long tunnel was driven at the Hope Valley Mine in the Sierra Nevada mountains of California in 1972 and 1973. An average of 1100 kg (1 ¼ tons) of a 172 MN/m2 (25,000-psi) granodiorite formation was broken by each of 590 shots used to drive the tunnel.l Based on these results it is estimated that REAM can drive over 60 meters (200 feet) of tunnel per day at about 88 percent of the cost of drilling and blasting. In addition, repeated axial impact by high energy projectiles was used to drill a 0.4 meter (16 inch) diameter horizontal hole in the same granodiorite formation. Each shot advanced the hole an average of 0.2 meter (8 inches).

Jan 1, 1976

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By K. Thomson

The Mule Canyon gold deposit, located 14 miles ESE of Battle Mountain, Nevada, was discovered in 1986 as the result of a GFMC grass-roots exploration program. Drilling to date has identified six discrete orebodies which contain a demonstrated gold reserve of 8.487 million tons at an average grade of 0.136 oz/ton, totaling 1,152,000 ounces. Mineralization is associated with argillic alteration and silicification, localized along NNW trending high-angle faults within Miocene basaltic andesites. Trace element geochemistry at Mule Canyon is typical of upper level hot spring precious metal systems, displaying elevated Ag, As, Sb, Hg, and Se.

Jan 1, 1993

By H. Salamanca

The electric operation and design features of the 11.000 H.P. variable speed SAG mill gearless drive is presented. The function of the frequency converter, control system drive and lubrication systems are described. An analysis of the harmonic characteristic in the Supply System and Motor is presented, and the dynamic development of the stator current, speed and the magnetic flux in the start-up process of the drive is evaluated. Besides, the most important aspects in the commissioning and maintenance of the drive are analyzed.

Jan 1, 1991

By S. V. Krishnan

Stability of fine quartz suspensions in process water is of concern in several mineral processing applications. In alkaline solutions, the presence of magnesium ions, arising from such sources as water hardness and magnesium-bearing minerals, leads to the precipitation of Mg(OH)2 which coats the surfaces of quartz. The conditions under which heterocoagulation or surface precipitation of Mg(OH)2 on quartz occur and the manner in which they influence the settling behavior of ground quartz was studied by means of settling tests, coating density determinations, zeta potential measurements and electron microscope observations. Coating density was greater when Mg(OH)2 nucleated on the surface of quartz than when the precipitates heterocoagulated on the quartz surface. The settling curves of quartz suspensions in the presence of different concentrations of MgCl2 exhibited a maximum of maxima which occurred at 10-3M MgC12 and pH 11. Interactions between quartz and Mg(OH)2, and flocculation-dispersion characteristics of quartz suspensions in this system are discussed.

Jan 1, 1983

By Toru Nakao

Fujiwara Quarry had been operated by the "Glory-hole Benchcut" mining system. But because it became difficult to meet the expanding demand by this system, "Central- shaft MCP" mining system was introduced in 1979. This MCP is equipped with a hydraulic walking system manufactured for the first time in Japan. Nowadays "Central-shaft" mining is the common method at limestone quarry in Japan. In this method crushing facilities are usually installed at the bottom of the shaft. But at this quarry, MCP was adopted and installed on the quarry surface. Many MCPs are operated in foreign countries, but in Japan few examples exist. Normally, Japanese limestone deposits lie in high mountains, which is obviously inconvenient for MCP to walk in and around the quarry. This difficulty, however, was overcome at this quarry, and MCP has been operated satisfactorily and efficiently for about 2 years after it was installed. In order to overcome the difficulty, in "Cen¬tral-shaft MCP" mining system, two mining methods are employed, the one is "SLICE-DOWN" mining method, and the other is "BLOCK-CUT" mining method.

Jan 1, 1982

By H. Ban

Triboelectrostatic separation tests were performed on a bench-scale, analytical separator using coal, coal combustion fly ash and mineral samples. Fractions of separated samples were collected and analyzed to characterize the performance of the separation. Particle size distribution and morphological characteristics for these samples were analyzed by optical microscopy, and scanning electron microscopy (SEM). It was found that smaller size fractions of a fly ash sample had better separation than the full sized parent fly ash sample, indicating interference or particle-particle interactions during the separation process. It was also observed experimentally that small kaolin particles attach to the surface of large silica spheres, causing charge neutralization and subsequent low separation efficiency.

Jan 1, 1997

By A. P. Mehta

The role of microorganisms in the leaching of metal sulfides is well established (Torma, 1977; Murr, 1980). However, this established knowledge applies mostly to chemolithotropic microorganisms such as Thiobacillus ferrooxidans which function optimally in leaching catalysis between 25-35° C, and in a pH range of 2-2.5. Although leaching with thermophilic microorganisms capable of extending the range of catalytic viability beyond 35° C is also documented, there are few if any attempts to optimize or extend sulfide concentrate leaching with thermophilic microorganisms. When mixed metal sulfides or other materials having different rest potentials (referenced to the standard hydrogen electrode, SHE, in the electromotive series) make contact in a conducting, aqueous medium, the contacting members will act as an electrochemical cell, with the member having the higher rest potential assuming the role of an electrical cathode. In leaching reactions involving such galvanic couples, the cathode becomes passivated, while the anodic member reacts vigorously due to the electro- chemical reaction which occurs (Hiskey and Wads- worth, 1975). Serry, eta1 (1978) observed that when chalcopyrite and pyrite were in intimate contact in natural ores, the chalcopyrite reacted vigorously by galvanic conversion as a result of the higher rest potential (~ 0.63 V) as compared to the chalcopyrite (~ 0.53 V). In addition, it was postulated that because of the elemental sulfur which can form on the anodic chalcopyrite in this galvanic conversion process, reactions in acid-bacterial medium would be expected to have accelerated copper extraction because of the conversion of any sulfur product layer on the chalcopyrite anode to sulfuric acid according to the following general reactions: [MS?M2+ + S° + 2e- (1) and 2S° + 302 + 2H20 bacteria?-2H2SO 4 (2)] where M in reaction (1) designates the metal (or metals in the specific case of chalcopyrite) to be released to solution by galvanic conversion.

Jan 1, 1982

By Ireneusz Tomza, Jolanta Lebecka

INTRODUCTION Radioactive deposits were observed in 1972 in some of the Upper Silesian coal mines. They were located mainly in the drains in galeries and on the inside surfaces of water pipes. They also caused some problems by accumulating in water pumps. It has been postulated that the deposits are produced by natural radioactive waters seeping from the rocks. Investigations were initiated to answer the following questions: - What is the composition and the amount of radioactivity in the deposits? - What radioisotopes are present in the water? - How are the radioactive deposits formed? - Do the radioactive waters also occur in other mines? - How does the radioactivity of the water depend on chemical composition? - What is the origin of the radioactive water? - Does the water and the deposits cause radiation hazards for miners? -How can the radiation hazard be reduced? METHODS OF MEASUREMENT Determination of Radium Isotopes in Water The commonly used methods of radium determination in water are either based on measurements of the radioactivity of 222Rn which is in equilibrium with 226Ra, or on the detection of alpha particles of the radium radioisotopes after chemical separation of radium from the water sample. The method based on radon activity measurements is very sensitive and does not require any chemical Separation, but it can be used for determination of 226Ra from the uranium series only, because the thorium daughter 220Rn has too short a half-life (55s to yield the required accuracy. The method developed by Goldin, 1961 [2] involved alpha-particle measurements in thin layers of RaS04 and BaS04 separated from the water. This method is not convenient for saline water and water with high barium concentration because the amount of barium carrier in this case is too large to obtain a thin layer of precipitate with sufficient activity. The Upper Silesian carboniferous waters are often saline with high barium content, so the method described by Goldin was not convenient for this case and it was necessary to change the detection system and modify the chemical preparation. The procedure developed by the authors for the determination of radium isotopes in water was as follows: - Depending on the Ba2+ content and the required sensitivity of measurement, a water sample of 200 cm3 to 3 dm3 was taken. - 10 cm3 of 0.25 M citric acid and 5 cm3 15M ammonia was added to form complex Ba2+ ions and avoid the immediate precipitation of BaSO4. (This was repeated as long as the addition of BaC12 did not form a precipitate.) - 1 cm3 of 1N solution of Pb(N03)2 as a carrier for radioactive isotopes of lead and 10 cm3 of 0.1 N BaC12 as a carrier for radium were added. - The sample was heated to the boiling point and the precipitation of RaS04, BaSO4 and PbS04 with 50% H2SO4 was carried out. - After several hours the sample was centrifuged and the precipitate was purified by washing with nitric acid and distilled water. - The precipitate was then redisolved in 20 cm3 0.125 M Na2EDTA and 3 cm3 6M ammonia and reprecipitated from the solution by dropwise addition of acetic acid to d pH of 4.5. At this value of pH, precipitation occurs only for the barium and radium sulfates, while lead and all other radioactive elements remain in the solution. The date and time of deposit precipitation was recorded. - The final barium-radium sulfate mixture was washed with distilled water and transferred to standard measurement vials. - Each vial containing a deposit had 6 cm3 of distilled water added and was then shaken vigorously. 12 cm3 of liquid gelling scintillator (INSTA-GEL UNISOLV-1 type) was then added and the vi 1 was shaken again. After a while the scintillator turns into a milky gel in which the deposit is uniformly distributed. - The standard sample of 226Ra was prepared in the same way. - The activity of the samples was measured using a liquid scintillation spectrometer. (In this case the TRICARB 3320 produced by Packard Instruments, was used). Tests run on standard radium solutions provided by Amersham Radiochemical Centre indicated that this method of measurement enables one to achieve an efficiency of almost 100% (within measurement error). For alpha particles no quenching effect was observed for the BaS04 concentration in the range up to 80 mg of BaS04 per 1 cm3 of liquid scintillator coctail (Fig. 1). This provides a sensitive determination of radium in water with high barium content and also in saline water. In saline water the solubility of barium sulfate is much higher than in

Jan 1, 1981

By William M. Phillips

This paper will concern the processing of kaolin clays from the sedimentary deposits of Georgia and South Carolina, While the major processing steps will be touched on briefly, emphasis will be given to the dewatering of the clay-water slurries (slips) formed in the processing of kaolin clays The dewatering steps discussed will include gravity settling, centrifugal dewatering, vacuum filtration, and thermal dryings Of these dewatering steps particular attention will be given to vacuum filtration and the variables affecting filtration of these kaolin clays.

Jan 1, 1962

By Frank W. Bowdish

During the early 1960's, a method was developed for refining sand from the Arkansas River to produce a feldspathic product that was proposed for use in making colorless glass. Because of the need for chemical uniformity, a cooperating glass manufacturer specified certain ranges of percentages for each chemical constituent of the sand. These specifications were met by fulfilling the single requirement that alumina vary by no more than 20.1 percent from the specified value. This translated to a total variation of only about 1 percent in the feldspar content of the mixed quartz-feldspar products. Because the feldspar was lighter than the quartz, the average density of refined sand varied depending on composition. Densities, determined to five significant figures, of several samples were correlated with their chemical analyses, and the correlation could then be used with density determinations to more reliably indicate compositions than by chemical analyses only. The effects of several variables on the composition of refined sands were studied. There was a regular variation in the proportion of feldspar with screen size. A series of samples with their natural size distributions were more nearly uniform in composition than the same sands after screening and recombination. The screening and recombination process was done so that the sands had identical size distributions. Variations in the refining showed little effect on composition. A pile of flow-back sand from a construction sand washer was found to be severely segregated. However, samples taken from many points in the river near the sand plant and from the flow-back discharge pipe over several weeks very nearly met the uniformity specification. If care was taken to avoid segregation either before or during processing, it should be possible to meet the uniformity specifications for a feldspathic glass sand.

Jan 1, 1978

By J. W. Wilson, S. Nakajima, B. D. Singh

According to the Project Independence blueprint, a 270 percent increase in coal production is expected from western coal fields compared to an increase of 100 percent for the nation as a whole. Furthermore, 30 percent of the total United States coal reserves lie in the western states, which are classified as beyond the strippable limits and can be recovered only by underground methods. In view of the fact that the majority of the seams in the West are thicker than those presently mined in other parts of the country, it is important to consider the parameters that relate to mining thick seams and the factors that affect such mining systems. Apart from thick seams, a common feature of many western coal fields is the occurrence of multiple seams that lie in close proximity to one another. These multiple seam deposits present difficult mining problems that have not been encountered to any degree in other U.S. coal fields; for example, ground pressure changes in one mine level caused by mining in the other, sudden water or gas influx from the adjacent levels, the danger of spontaneous combustion in gobs and large and complex subsidence displacements on the surface. Perhaps equally important is the fact that the country can ill afford the present systems of underground mining that attain only 50 to 60 percent coal recovery. With the probability of increased thick seam mining, conservation shall be a focal point in future mine design systems. It is possible that in the future it will be forbidden to adopt the present day wasteful mining methods to ensure that coal can be conserved for future generations.

Jan 1, 1977

By J. Keng, S. T. Chen, T. M. Shih

Kwanyin Tunnel is presently the longest (7.7 km) railway tunnel in Taiwan. Due to heavy railway traffic, a pass-by station will be built inside the tunnel to increase the traffic flow. Since the concentration of toxic gases released by the locomotives may reach dangerous levels, a research program was conducted for the purpose of designing a ventilation system which could dilute and/or remove the toxic gases to maintain an acceptable pollutant level. The program consisted of two parts. The first part was field measurement during which the concentrations of pollutants and wind velocities were measured at various points inside the tunnel to acquire basic data regarding ambient air quality, piston effects for the different types of trains, and existing ventilation conditions. Weather data (temperature, humidity, atmospheric pressure, wind direction and velocity) were gathered at many stations, both on the surface and inside the tunnel. The amount of pollutants released by each type of locomotive for various conditions were also measured. The second part of this study involved establishing mathematical models for predicting the air quality of the various proposed ventilation systems. Three different models were used for this work. The first one is a piston effect model which assumes that the gases and air undergo immediate mixing inside the tunnel. The second one is also a piston effect model which assumes that the diffusion ability of the gases is zero. The third one is a conventional ventilation model which was used for natural and mechanical ventilation conditions. From the result of field measurement and mathematical model studies, a ventilation system was chosen with consideration of both ventilation effects and construction costs.

Jan 1, 1987

By Carl E. Williams

Several years ago it was decided that ASARCO was in need of a good mine scheduling program to complete the computerized open pit mine planning package that was being used on new prospects and operating properties. A trial and error approach was being used to schedule a mine on a year by year basis, but this was time-consuming and far from offering an optimum solution l. Due to the magnitude of time and expertise required to develop such a sophisticated computer program, it was decided to search outside of the company for one already developed and available for purchase, This proved fruitless and therefore proposals were requested from consulting firms that had the expertise to develop such a program. Out of the five firms that submitted proposals, the one chosen was Systems Control, Inc., (S.C.I.) of Palo Alto, California. S.C.I. was selected because it was felt that they offered the greatest capability in the mathematical solution of complex problems. But due to their lack of mining expertise, a cooperative venture was developed whereby ASARCO would supply this mining knowledge. The selection of this vendor, the formulation of the contract and specifications, and the development of the computer program required about 3 years to accomplish.

Jan 1, 1973

By C. Orf. Chukabarah

Erratic behavior in convergency during iterative numerical-method evaluation of mine ventilation fan characteristic curves is one of the common problems encountered in mine ventilation network analysis. Five different sets of mine fan data points, that had resulted in unsatisfactory fan characteristic curves, were re-analyzed in the present study, using an embedded mine network optimization computer program. Current results revealed that all five fan data sets not only can be satisfactorily fitted as Yang (1992) did with MFIRE subprogram, but can further be optimized with unique solutions as implemented in the present study. It was concluded, inter alia, that the improved MFIRE-based mine fan curve-fitting computer subprogram (SPLINE) produces satisfactorily similar fan curves as SPSS-based curve-fitting algorithms, including when the latter method uses either standardized or unstandardized fan curve data sets.

Jan 1, 1993

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By Joseph L. Condon

The U.S. Department of the Interior, Bureau of Mines, is doing research on methods to obtain premining information on problems such as detection of old mine workings, abandoned oil wells, channel sands, faults, and other geologic features that are undesirable from a production or safety aspect. Techniques being developed to acquire the necessary information include seismic and electromagnetic. The seismic methods include high-resolution seismic and acoustic methods applied from the surface and inseam channel waves applied under- ground. The electromagnetic, or radar, methods are applied from the surface, from boreholes, and from the working face underground. All of these methods are useful under certain site-specific conditions, but none of these methods is universally applicable for all mining conditions.

Jan 1, 1980

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each; other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997

By D. G. Bosse

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing These are fairly well understood and provide the starting point for decisions Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X This additional major variable IS not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures

Jan 1, 1983