Search Documents

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Gunther Schimmel

Ag exudation in four different alloys (Ag-Cd, Ag-Sn, Ag-Sn-In and Ag-Zn) is characterized. The amount of exuded material is correlated with the volume increase due to oxide formation in dependence of the alloy concentration and different densities of the oxide and matrix phases. It is shown that all four alloys show similar amounts of volume increases, but different amounts of exuded material. It is concluded that internal stresses due to the volume increase cannot be the dominant driving force for Ag exudation. A gradient in the chemical potential of Ag that originates from the O concentration gradient inherent to internal oxidation is suggested as driving force. The exudation behavior is thus governed by the variation of the activity of Ag in the Ag fcc phase in the Ag-Me-O system that differs between the alloying systems.

Jan 1, 2010

By Zhongning Shi, Ramana G. Reddy

"By cyclic voltammetry and potentiostat electrodeposition using Potentiostat/Galvanstat, electrochemical behavior on Ag electrode in electrolyte 0.2M NaOH+0.01MPb(NO3)2-0.01M TeO2 -0.01M TlNO3 solution were also carried out at 298K. The processes of electrodeposition of Tl2Te3 and PbTl4Te3, a thermoelectric material, are reported along with analysis of the composition of the obtained deposits. The results showed that two different underlying processes are occurring depending on deposition potential. One process involves the reduction of TeO3 2- and Tl+ to Tl2Te3 in a potential interval of -0.70V < E < - 0.89V (vs. Hg/HgO). A second process at more negative reduction potentials involves reduction of TeO3 2-, Pb2+ and Tl+ to PbTl4Te3 in a potential interval of -1.02V < E < - 1.19V. The crystalline Tl2Te3 and PbTl2Te3 were deposited electrochemically on Ag substrates at -0.84V and -1.10V respectively. Thermoelectric (TE) material can form a temperature gradient across the material to make electric voltage, which is popular in waste heat utilization and recovery industry. Lead telluride, PbTe, is a small band gap semiconductor of 0.32eV at 300K. PbTe can change its n-type semiconductors with Pb-rich to p-type semiconductors with Te-rich[1]. And it is one of the best TE materials used in thermoelectric generators working between 500K and 600K, or even at a higher temperature of 800K.Three facto,rs play a role in the performance of a thermoelectric material: electrical conductivity (s), thermal conductivity(?), and the Seebeck coefficient (S). These can be combined with absolute temperature (T) to give a figure of merit (ZT) for the material, ZT = s2sT/?. By increasing the electrical conductivity and decreasing the thermal conductivity, which can enhance the ZT value, many efforts, such as alloying with other elements and making the materials nano-sized, have been done to improve its properties recently. Hsu et al. reported that the ZT value of Cubic AgPbmSbTe2+m is increased to 2.2 by doping Ag-Sb to PbTe.[2]."

Jan 1, 2011

By Jennifer Murphy, Brad S. Schake, Karol Holmes, John R. FitzPatrick, Mike H. West

"The separation and purification of uranium from either nitric acid or hydrochloric acid media can be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps.We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (1 DO-gram) flow experiments, using depleted uranium, were done after the small-scale evaluation of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos.Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process.Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail."

Jan 1, 1996

By Shengli Wu, Fengjie Zhang, Feng Chang, Hua Lu, Kaiping Du

In order to make a complete understanding of steel plant metallurgical dusts and to realize the goal of zero-waste, a study of their properties was undertaken. For these purposes, samples of two sintering dusts (SD), two blast furnace dusts (BFD), and one electric arc furnace dust (EAFD) taken from the regular production process were subjected to a series of tests. The tests were carried out by using granulometry analysis, chemical analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy via SEM (EDS), and Fourier transform infrared spectroscopy (FTIR). The dominant elements having an advantage of reuse are Fe, K, Cl, Zn, C. The dominant mineralogical phases identified in sintering dust are KCl, Fe2O3, CaCO3, CaMg(CO3)2, NaCl, SiO2. Mineralogical phases exist in blast furnace dust are Fe2O3, Fe3O4, with small amount of KCl and kaolinite coexist. While in electric arc furnace dust, Fe3O4, ZnFe2O4, CaCO3, CaO, Ca(OH)2 are detected.

Jan 1, 2015

By S. Gopalan, J. D. Milshtein, S. N. Basu

Production of syngas is proposed utilizing the W/W03 redox system and employing a solarpowered two-step thermochemical cycle. Three chemical reactions occur in two chambers. Assisted by a solar concentrator, a high temperature reaction reduces W03 powder to metallic tungsten in both chambers. Subsequently, the temperature in one of the chambers is lowered and H2(g) is produced via re-oxidation of the tungsten powder using steam. The temperature in the other chamber is simultaneously lowered to an intermediate temperature and CO(g) is produced via oxidation of the tungsten powder using C02(g)· The gas streams coming out of the two chambers result in the syngas production. A complete thermodynamic analysis of the system is described. The W/W03 redox cycle offers greater gravimetric fuel productivity compared to previously proposed systems, and the entire cycle can be operated below 1273K.

Jan 1, 2013

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

The copper concentrate market is becoming increasingly unstable. In the early 1990s large concentrate stocks were built up and the glut was cleared only after treatment charges rose so sharply that &apos;non-traditional&apos; custom smelter capacity, such as in Kazakhstan, could be employed, By 1994 the market had shifted and Western smelters were unable to secure enough concentrates to operate full out. The reason for these sharp swings in the market balance is that virtllally all the recent mine development has been non-integrated. With different companies developing new mine . and smelter capacity, it is inevitable that the pace of expansion in the two sectors will not be coordinated. For many years the Japanese smelters were the major buyers from the new mm-integrated mines. However, Japanese smelter capacity is unlikely to increase appreciably in the future and this stabilizing influence will be very difficult to replace. This paper will examine the likely concentrate/smelter balance over the next five years and will forecast the likely direction of? treatment charges. It will also touch on the critical variables in assessing the viability of new greenfield custom smelter capacity, such as proximity to concentrate sources, by-product sulfuric acid prices and, most importantly, tariff protection.

Jan 1, 1995

By Lev Levin, Sergei Lesokhin

"The formation of titanium carbide during hot filament assisted carburizing of NiTi alloy was investigated. Phase content and morphology of the diffusion zone were examined by X-ray diffraction, X-ray microanalysis, SEM, and Auger electron spectroscopy. The growth of stable and adherent TiC film was observed. A non-planarity of interphase boundary was noticed. The applicability of the chemical diffusion approach to the analysis of the experimentally observed interface instability is discussed. A criterion, taking into account the influence of growth stresses on the stability of the flat interface, is developed by means of linear perturbation analysis.Introduction.Equiatomic intermetallic NiTi belongs to a class of materials exhibiting the shape-memory effect. The unusual property of this compound promotes its application in many fields, from aerospace technologies to medicine. The relatively high ductility ofNiTi also permits its use as a matrix material in metal-ceramic composites. The objective of this work was to investigate the possible incorporation of a ceramic material (titanium carbide) into NiTi by gas carburizing.Free energy calculations indicate the potential to obtain TiC by carburizing Ni-Ti binary phases. The main obstacle to such a process is the high affinity of titanium to oxygen. At moderate temperatures the formation of TiC is preferable to titanium oxidation only if the partial pressure of oxygen is extremely low [1]. This problem was overcome in this work by the use of hot filament assisted gas carburizing. Due to chemical reactions occurring near the hot filament, the gas mixture, initially consisting of methane and molecular hydrogen, was enriched by atomic hydrogen [2], drastically decreasing the content of free oxygen in the carburizing atmosphere.The second part of this article concerns the theoretical analysis of reasons that lead to the development of the experimentally observed morphology of the diffusion zone. In particular, the influence of the growth stresses on the morphology of an interphase boundary is investigated."

Jan 1, 1996

By Robert Matusewicz

Ausmelt Technology has been applied to the recycling of spent pot liner (SPL) generated from primary alnminum production. The process is centered on the Ausmelt furnace, in which the SPL is converted under high temperature, oxidizing conditions to an HF containing gas stream and inert slag. fluorine is recovered from the SPL as HF gas and is concentrated and used to manufacture AIF) for recycle to the aluminum smelters. Approximately 87% of the fluorine can be recovered and converted to AIF), with the remainder being effectively tied up in the by product slag. Cost projections show that the recycling process will be competitive with other processes for SPL. The production and recycling of AIF) provides available credit that significantly offsets the operating cost of the facility. Ausmelt Technology for recycling of SPL is currently being marketed in North America by Ausmelt Technology Corporation in Denver, Colorado, and in the rest of the world by Ausmelt Limited of Dandenong, Australia.

Jan 1, 1996

By Joseph C. Milbourne

Tetra Technologies CCIX? (continuous countercurrent ion exchange) system has been involved in a wide range of uranium concentration, separation and purification applications over the past 40 years. Uranium ion exchange applications have ranged from the treatment of copper heap leach solution containing 5 parts per million of uranium to the treatment of high strength sulfuric acid solutions containing several thousand parts per million of uranium. The flexibility and the countercurrent mode of operation and other unique features of the CCIX? have resulted in successful uranium recovery from these solutions and many others.

Jan 1, 1995

By B. Q. Li

A numerical study of the developing fluid flow and thermal aspects during the staning phase of aluminum continuous casting processes is presented. The deforming finite element method, coupled with a quasi-Lagrangian formulation, is used to represent the growth of an ingot and the dynamic fluid flow and thermal behavior that evolves in the growing ingot. The mathematical formulation of the problem and the numerical treatment are discussed. The algorithm solves the free moving nodes as part of total unknowns with an automatic time step control for time integration. This permits an optimal computing efficiency while still keeping the computational errors under control. A selection of the results obtained using the algorithm is presented. The results are concerned with the evolution of fluid flow, temperature and solidification phenomena during a DC round ingot casting process, as it evolves from the beginning of casting operation to a steady state. These results show that the time-varying, complex fluid flow and thermal phenomena during continuous casting processes can be very well represented by the computational algorithm. The results also illustrate that, during the casting process, ~e fluid flow and temperature fields change drastically at the initial stage but evolve slowly afterwards

Jan 1, 1993

By A. Shemi

Tungsten carbide scrap (WC–Co) is material generated from the tungsten carbide manufacturing process and worn out or used carbide parts from industry. Tungsten (W) ores contain about 3 wt% WO3 and their W concentrates about 10– 75 wt% WO3. Tungsten carbide scrap typically contains 40–95 wt% W. The high intrinsic value of W and the fact that the least valuable scrap contains more W than the average tungsten ore makes tungsten carbide scrap a worthy material for re-use. This study has investigated the selective dissolution of the cobalt (Co) binder phase, and recovery of tungsten monocarbide (WC) and Co using an acid leach process. The Co component was selectively leached leaving the WC solid particles intact. Further investigation using a complexing agent-aided acid leach process that takes advantage of organic chelating agents that form a soluble tungsten complex in place of the passive insoluble tungsten oxide is envisaged. The optimal dissolution of the Co binder phase using an inorganic acid in conjunction with an organic complexing agent is a novel approach with the potential of reduced leaching times and possibility of regenerating the unreacted organic acid.

By Jason H. Nadler, Jason A. Kulpe, Stephanie J. Lin

"A numerical method has been developed to predict the microstructural characteristics of reticulated metal foam. The porosity of this foam is derived from sacrificial template particles of known particle size distribution, which are incorporated with other precursor components. In this approach, a porous structure is numerically generated starting with Powell's sphere packing algorithm. The resulting stochastic structure has characteristics similar to those of corresponding metal foam. Deterministic inter-sphere connections are calculated to more accurately model the pore morphology that evolves during thermochemical synthesis. Estimations of pore morphology and specific surface area of the simulated material are compared to lab-synthesized materials composed of equivalent constituent compositions. In addition, the effect of template particle size, inter-sphere connections, and the geometric constraints on pore morphology and permeability are investigated to refine microstructural evolution and design.IntroductionReticulated foams, characterized by their interconnected pore network, can be obtained by incorporating spherical sacrificial template particles into precursor materials followed by template removal processes. The resulting structure is composed of contiguous spherical pores whose morphologies reflect those of the original templates. Based on some of the unique features of this synthesis approach, a methodology is introduced in this work whereby these foams are digitally constructed using experimental data from the template particle sizes and precursor formulation. Digitally constructed porous structures can then be compared to their laboratory synthesized counterparts through the quantification of structural features such as porosity and surface area per unit volume, which in tum are used to inform the foam's fluid transport propertiesThe spherical template particle packing algorithm developed here is adopted from Powell's work [1], which also includes approaches to obtain percolation and density in random packings [2]. Gervois gives a mathematical development for the stereological sectioning of packed hard spheres [3]. Stereological sectioning facilitates determination of relevant three dimensional morphological properties from two-dimensional data [4]. Studies on the sphere distribution size and the related particle packing density and coordination number results are studied in [5, 6]. Lastly, Kato describes a sintered neck structure, which is used with these packings [7]. This neck structure, as a model of the particle shape following heat treatment, is implemented here in a similar manner. A strong difference between the available literature and the methodology here is that spheres are packed to ultimately represent porous space, not rigid solid space."

Jan 1, 2011

By Roberto Parreiras Tavares, Frederico da Costa Fernandes, Guilherme Antonio Defendi, Vangleik Ferreira da Cruz, Júlio César de Sousa Pena

"Near-net-shape casting is an important area of research in the iron and steel industry today. Among the near-net-shape casting processes, the single-belt caster seems to be the most promising, since it is the only one that can achieve levels of productivity similar to those obtained with conventional continuous casting machines. One of the most important aspects in the single-belt casting is the feeding system used to deliver liquid metal over the belt. This system determines the velocity distribution and the levels of turbulence of the liquid metal and affects the quality of the strips. In the present work, a metal delivery system having a simple geometry was proposed. Using the CFD code CFX 5.6, a mathematical model to simulate three-dimensional turbulent fluid flow and heat transfer in that system has been developed. This model was used to analyze different configurations of the metal delivery system and the free surface shape of the fluid was also determined. A physical model of the feeding system was built and used to validate the predictions of the mathematical model. The fluid flow calculations have been validated by dye injection experiments and laser doppler anemometry. Measurements of the free surface levels have also been performed. These experiments provided supporting evidence for the predictions of the mathematical model.IntroductionTo maintain its competitiveness in the present market, the metallurgical sector, particularly the steelmaking companies, are developing new techniques of production. Some of these new processes are focussed on the strip casting technologies. Among these technologies, the SingleBelt process is considered the most interesting option, reducing the number of rolling steps and, consequently, the final cost of the product, especially the part associated to the energy consumption (fuel and/or electric energy). This process can also reach levels of productivity that can not be matched by other strip casting methods(1). One of the most important aspects concerning these new processes is related to the liquid metal delivery system. This system can have a significant effect on the final quality of the strips, since it determines the velocity distribution and the levels of turbulence of the liquid metal."

Jan 1, 2004

By Frank A. Vonesh

In order to reduce the amount of visible, airborne emissions in the Metals Industry, a new Industrial Gas Technology was developed by Air Liquide. This patented technique is called ALECT?, Air Liquide Emission Control Technology. Demonstrations have been conducted for many cutting and lancing operations as well as for hot metal transfer from vessel to vessel. Fume reductions of 90% and greater have been achieved in actual practice. Air Liquide continues to improve the process and the associated control equipment.

Jan 1, 1994

By A. Hasko

Phytoremediation is a new low cost alternative technique for remediation of contaminated soils from heavy metals that are emitted by ferrous and nonferrous mining and extracting processes. It is based on the possibility to use several plants that accumulate high level of metals in order to remove metallic pollutants from soils and render them harmless. Phytoextraction is an adjacent new technique that uses these hyper-accumulator plants in order to extract the metals from them using even the conventional smelting or refming processes. In our previous work, an extensive investigation of about 150 plants have been carried and several species were identified that could be used for nickel phytoremediation and phytoextraction because of their high accumulation of nickel. It has been found that five taxa from Alyssum genus specie had the highest ability to accumulate nickel with concentrations more than 10000 ug/g (dry weight) or 1%. The taxa showing the highest accumulation of this metal is Alyssum murale var. chlorocarpum with 28 600 ug/g or 2.86%, a good candidate for Phytoextraction. In this work, in order to optimize the phytoremediation and phytoextraction processes further Absorption Spectrometry measurements and biological studies were carried out to determine the parts of the plants that accumulate the highest amount of nickel and the best biological cycle during which they accumulate the highest amount. The results show that the greatest accumulation of nickel occurred in the leaf material (2.86%) and the least in the roots (0.43%). The investigation of the biological cycle of the genus Alyssum showed that: (1) the seeds germinated between 50 C to 30 0 C and more in 25 0 C; (2) 62.9 % of seeds germinated at A.m. var. chlorocarpum; (3) the emergence is almost continue from March to April; (4) the anthesis occurs from May to July; (5) the ripening of the fruit takes place 30 days after flowering; (6) the dissemination of fruits occurs from September to October. Due to these special characteristics it is reaffirmed that Alyssum murale var. chlorocarpum, as a nickel hyperaccumulator, is the most promising plant to be used for feasible phytoremedation and phytoextraction purposes. Keywords: Key words: Phytoextraction, PhytoRemediation, Nickel accumulators, Alyssum sp., Biological cycle

Jan 1, 2003

By Adam Powell

A Cahn-Hilliard phase field model is formulated to describe transport-limited electrochemical reactions coupled with fluid flow in a metal reduction cell. When the reaction is limited by mass transfer of metal ions from the electrolyte to the cathode, the metal-electrolyte interface at the cathode exhibits a Mullins-Sekerka instability, leading to the growth of dendrite-like "streamers" of liquid metal into the electrolyte, which in turn significantly enhance the apparent mass transfer coefficient there. Model results for iron reduction from ferrous oxide in slag show formation of these streamers. Although the double-layer is not included in this model, the related phenomenon of electrocapillarity can be represented by a gradient penalty term which includes the electric potential gradient, such that interfacial energy is a function of the electric field normal to the interface.

Jan 1, 2003

A simulation of a capper concentrate smelter was built with a capacity of 450,000 tons per year. The system&apos;s components to simulate were three : a Reverbetory furnace, a Wiente &apos; s modified converter ( TMC ) and two cranes. The system was classified as dynamic, stochastic and discrete. In the simulation language choice it was concluded that the most advantageous one was GPSS/H. The model verification was done through the interactive Debugger that the language has and the statistical validation was done through the result variables of sane activities, that as a whole characterize the system (charged matte and charged concentrate to the TMC, skimming white metal and skimning slag). The validation was done comparing the simulation results of these variables with the ones obtained for those variables in a specific month in the smelter. The comparison consisted in a difference of means test and in all cases the equality was accepted with a 95% of confidence. The animation tool was PROOF, a general purpose animator, that is used after processing the simulation.

Jan 1, 1994