Search Documents

By Z. Zborovszky

The feasibility of using the nucleation properties of combustion generated particulates for the identification of their sources was investigated, using the Cloud Condensation Nuclei (CCN) Spectrometer. The Investigated materials included coal, wood, belt materials, electrical insulation, brattice cloth, and diesel exhaust. The materials were heated In an oven using filtered air flow, and their time, temperature, and the critical supersaturation spectrum of condensation nuclei (also referred to as the CCN spectrum) produced by the combusting material were recorded. Some data was obtained on a typical metal-mine background containing blasting products. The data was processed and analyzed In an attempt to specify parameters and limits that would allow the identification of the combustion sources. It appears that under controlled test conditions It Is possible to Identify the source on the basis of data derived from the CCN spectrum. More general use of the Idea for fire detection under uncontrolled practical circumstances in an actual mining environment does have potential but would require further research.

Jan 1, 1978

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By Jacqueline V. Rich

The relationship between surface and ground water quality and copper mining in the Globe-Miami area is investigated in this three-year study. Methods to prevent, minimize, mitigate, or treat polluted waters are identified and evaluated. Best Management Practices are incorporated in a recommended plan to manage the area's water quality.

Jan 1, 1983

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

By M. Deal

Particle size analysis is a fundamental measurement utilized in the mining industry, especially in comminution, hydrometallurgy, and mineral processing. While sieves and cyclosizers are the standard methods used to determine particle size distributions, in recent years alternative instruments have been developed that claim to provide more rapid and equally reliable results. Newmont Metallurgical Services has implemented the use of two such instruments, along with traditional methods (sieves and a cyclosizer), on a daily basis. The Malvern Mastersizer 2000 laser analyzer is a wet sample system that can analyze particles in the size range 0.02µm to 2000µm, and the Horiba CAMSIZER® is a dry system that can analyze particles in the size range of 30µm to 30mm using digital image processing. A comparative analysis has been performed to determine the applicability of each particle sizing method in laboratory testing.

Jan 1, 2011

By L. W. Berger, and R. I. Jaffee, D. N. Williams

The effects of hydrogen on the properties of binary Ti-A1 alloys containing 2.5, 5, and 7 pct aluminum and ternary alloys of the same compositions with added interstitial elements oxygen, nihrogen, and carbon were stzdied. Aluminum increases the apparent hydrogen solubility of the a-phase, resulting in a marked increase in resistance to impact embrittlement. In the Ti-5Al and Ti-7Al alloys, for example, the addition of 180 and 305 ppm hydrogen, respectively, did not cause embrittlement, while unalloyed titanium was embrittled by as little as 75 ppm. The role of aluminum in increasing hydrogen solubility of the a-phase probably accounts for the excellent hydrogen tolerance of a-ß alloys containing considerable amounts of aluminum. There is some evidence that aluminum retards the rate of hydride precipitation. If so, these alloys may be susceptible to slow-strain embrittlement. UNALLOYED a-titanium is extremely sensitive to small amounts of added hydrogen in that there is a marked decrease in notch properties. For example, as little as 100 ppm hydrogen is sufficient to lower the room-temperature notch-impact strength from over 100 to less than 20 in.-lb.' This loss of impact Strength has been associated with the Presence of hydride phase in the microstructure. Hydrogen in the amounts encountered in commercial practice

Jan 1, 1959

By T. H. Chan

As the University of Hong Kong and their advisors planned their new Centennial Campus it became clear that they would have to re-provide existing water reservoirs on an adjacent site with new salt water reservoirs located underground in two new caverns. The existing reservoirs are owned by the Water Supplies Department who provide salt water for sanitary flushing and a separate potable water supply for regular use. Although underground reservoirs had not previously been adopted locally, the planning has been completed to a tight schedule and the construction is well advanced. The need to preserve historic buildings imposed constraints, as did the requirement to minimise potential construction nuisance for the local community and environment. This paper presents the background to the project and the work carried out to develop an innovative, sustainable and environmental acceptable solution. Construction progress to date is also presented.

By F Linares, B De Waele, K Bischoff, M Lacorde, G Loveday

Recent exploration has identified the presence of detrital iron deposits (DIDs) associated with banded iron formation (BIF) units in the north-west of the Congo Craton, Gabon. The regional geology comprises a complex of granitoids and gneisses assigned to the Archaean Chaillu Complex, within which older slivers of lower amphibolite-grade greenstones are preserved including muscovite-biotite-garnet-bearing felsic schist, amphibolite and BIF. These units are typically overlain by several metres of residuum comprising colluvium, eluvium and duricrust. The residuum is overlain by a regionally extensive loess cover from 2 m to 10 m thick.The DIDs occur within the weathered residuum as mostly unconsolidated gravels with lesser canga (CAN) duricrust draped over deeply weathered hematite. Head grades are in the range of 45 to 52 per cent Fe. Fresh BIF, located from 30 to 50 m below surface, is comprised of magnetite-quartz±amphibole. The detrital iron gravels are comprised of rod- and plate-shaped clasts of hematite (martite)-maghemite-goethite composition, in a ferruginous sand to clay-sized matrix. The DID form ridges and plateaus that coincide with magnetic highs defined using high-resolution ground magnetic surveys.The field relations and petrography indicate that the detrital iron accumulations are the result of weathering (including enrichment) and erosion of primary BIF. This includes removal of quartz, further oxidation and re-cementation of BIF to form ferruginous caprock. This cap and the in situ oxidised BIF were subsequently disaggregated and liberated, and further weathered to form the detrital iron accumulations.Metallurgical test work on bulk detrital iron samples has shown this material can be upgraded to lump and fines iron ore products with grades of 62 to 65 per cent Fe using simple scrubbing and wet screening, followed by dense media separation of the -1 mm fraction, with overall mass yields from 75 to 85 per cent. The test work indicates a high ratio of lump to fines products, sometimes exceeding 50:50.CITATION:De Waele, B, Lacorde, M, Bischoff, K, Loveday, G and Linares, F, 2017. Geological and metallurgical characteristics of banded iron formation associated detrital iron mineralisation in Central West Africa, in Proceedings Iron Ore 2017, pp 259–268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By J Charbucinski

Commonwealth Scientific and Industrial Research Organisation (CSIRO), Exploration and Mining, has developed nuclear spectrometric techniques for borehole logging. The paper reviews the latest developments of this technology for the metalliferous mining industries. The SIROLOG logging system developed by CSIRO Exploration and Mining has been commercialised and is available to the mining industry.

Jan 1, 2000

By A. A. Stripling

The Cretaceous limestone wells of the Mara/Maru-caibo Dist. of Venezuela are extremely prolific producers. To maintain production on cessation of natural flow, large scale gas-lift operations were commenced involving high production rates on caring Flow. For the design of these gas-lift installations it was essential to have some knowledge of the pressure gradients involved in casing flow, so that the required injection pressures, optimum gas injection raws, etc., could be forecast. This paper presents a method of calculating these annular pressure gradients. Basically the method makes use of an energy balance equation coupled with an empirical energy loss factor derived from field data. The calculations have been put in a form suitable for "punch card-type" calculating machines. A set of gradient curves for Mara/Maracaibo conditions covering flow rates up to 12,000 B/D, and GOR's of 500 to 2,000 cu fd/bbl is presented. From these curves the flowing BHP can be predicted from surface data and the vertical pow performance under varying conditions of gas injection can be estimated. The method has been applied to La Paz and Mam gas-lift operations for over three years and has given consistently accurate results. INTRODUCTION The Cretaceous limestone fields of the Mara/Maracaibo area in Venezuela are characterized by the presence of widely distributed fissure systems. Under these conditions individual wells frequently have extremely high potentials and such wells are generally flowed on the casing-tubing annulus in order to reduce the pressure loss in vertical flow. To maintain production on cessation of natural flow, an extensive gas-lift system was planned. As a first approach to this gas-lift design problem, an attempt was made to construct a set of empirical flowing gradient curves from the available subsurface pressure data. Such a method has been used successfully for tubing-flow conditions in California by Gilbert'. Unfortunately, the empirical construction of casing-flow gradient curves presents additional difficulties, as pres- sure bombs cannot bc run in the casing-tubing annulus against high rates of flow. Thus, the Full flowing gradients cannot be defined by actual measurement and the best that can be done is to obtain spot pressures at the tubing shoe. Under these conditions a vast accumulation of BHP data is required to construct a set of gradients. To the La Paz and Mara fields the majority of the available flowing pressure measurements fall into a relatively narrow GOR range, in the neighborhood of the solution ratio. While there appeared to be reasonable prospects of constructing gradient curves for this limited range, measurements at higher GOR's, which were of major interest for gas-lift operations, were relatively few and the prospects of constructing empirical curves cor~spondingly remote. As an alternative approach, the possibilities of a mathematical analysis of vertical flow conditions were investigated. May and Laird2fV n 1934 presented an excellent analysis of the vertical-flow conditions in the Anglo-Iranian Oil Co.'s fields. Their analysis was based on an energy-balance equation and calculated the losses due to kinetic energy, friction and slippage separately. By combining these losses with the total calculated available energy, the required depth-pressure traverse could be deduced. On applying the method to La Paz conditions, good results were obtained for tubing flow at high tubing-head pressures. However, for lower wellhead pressures (300 psi and under) the discrepancy between calculated and measured values increased appreciably. It was considered that this was probably due to energy losses caused by slippage or liquid hang-up in a continuous gas phase, for which it was difficult to visualize any analytical approach. In 1952 Poettmann and Carpenter4 presented a method of pressure gradient calculation which, while based on an energy-balance equation similar to that employed by May and Laird, made no attempt to evaluate the various components making up the total energy loss resulting from irreversibilities of flowing fluids. Instead, they proposed a method of analysis which assumed that all significant losses for multiphase flow could be correlated in a form similar to that of the Fanning equation for frictional losses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The total available

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By E. L. Thyse

Keywords: Pyrometallurgy, converter, nickel, matte, distribution Metallic elements occupy a wide range in granulated nickel converter matte phases. The distribution of these metallic elements, particularly during crystallization path events, appears to be poorly understood. The present study serves to investigate the distribution of Fe, Co, Ni, Cu, and Pb between nickel-sulphide, copper-sulphide, and alloy phases. A novel combination of thermo-chemical modelling, electron microscopy, and electron probe microanalysis was applied to understand crystallization path events and the associated metallic element distribution. This study has demonstrated that major Ni incorporated during copper-sulphide crystallization would serve to mobilize minor Co towards distribution in copper-sulphide phases. In addition, solid solution substitution of Cu by Ni is manifested by compositional zoning of copper-sulphide phases. The role played by Ni during alloy crystallization suggests that minor Co was also mobilized, along with an increase in principal Ni. Fe, by contrast, seems to be incompatible with principal Ni. In addition, solid solution substitution of Ni with PGEs and Cu is manifested by compositional zoning of NiCu-alloy phases.

Jan 1, 2011

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By Bruce Mennie

PT Freeport Indonesia (PTFI) operates copper and gold mining operations in a mountainous area of the Mimika regency, near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. The mining and concentrating operations typically produce 240,000 metric tonnes per day of Copper and Gold ore from the combined mining of an 80,000 tonne per day (ore) block cave operation (DOZ Mine) and a 160,000 tonne per day (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open pit mine will be complete in 2016 at which time PTFI?s operations will convert to Underground. Mining operations will transition from today?s mixed surface and underground operation to full underground mining over the next 6 years. This paper reviews the history of Redpath?s relationship with PTFI, beginning with a raiseboring contract in 1981 and evolving into vertical and horizontal development contracts of up to 37,700 equivalent metres of lateral development and 4,000 metres of vertical development in 2011. An overview of the current operations (PTFI?s Grasberg Open Pit and DOZ Underground Mines) and transition period (challenges for the transition from current to future underground mines) is presented with details of development of common underground infrastructure and future mines; Big Gossan Mine, DMLZ Mine, Grasberg Block Cave Mine, and the Kucing Liar Mine.

Oct 1, 2010

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By Liming Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by the National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m (984 ft), while the length of the panel is changed between 1,000 to 2,000 m (3,280 to 6,560 ft). The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined.

Jan 3, 2010