Search Documents

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963

By Jeffrey Y. Foley

Chromite deposits along the Border Ranges Fault in southern Alaska were investigated by the Bureau of Mines. This report, part 1 of a two- part series, describes the deposits. Part 2 describes the mineralogy and the results of metallurgical tests. Fieldwork began in 1981 and continued through 1983. Ninety-four subeconomic podifom chromite deposits in eight mafic-ultramafic complexes were investigated. Previously unreported chromite deposits at Red Mountain on Kenai Peninsula, on Kodiak Island, and near Tonsina are described. Deposits range in size from less than a thousand tons to over 1.25 million tons of contained chromic oxide (Cr203). Grades range from about 5 to 10 pct chromite. Excluding all deposits more than 10 miles from tidewater or existing roads and all deposits containing only chemical- or refractory-grade chromite, about 2,200,000 tons of Cr203 are contained in 41 hard-rock deposits. A placer deposit contains an additional 556,000 tons. These 42 deposits constitute a subeconomic indicated and inferred reserve sufficient to meet the Nation's chromite demands for about 4 yr, or the metallurgical industry's demands for over 5 yr, at 1981 consumption rates.

Jan 1, 1985

By Jeffrey S. Newman

This report establishes a methodology for the evaluation of gas detection devices and is the result of a critical investigation into the basic principles defining gas detector performance. A scheme is presented to evaluate the performance of a test sample of gas detectors based on the detector type and intended application. Test procedures, worksheets, test apparatus, glossary and statistical methods for handling test data arc given. In addition, evaluation standards and test parameters are identified. It is intended that this report serve as a comprehensive framework for the eventual certification of all gas detectors for mine applications. A plan is proposed and recommended for the quantification and implementation of evaluation standards for gas detection device certification.

Jan 1, 1980

By S. L. Zekovic

This paper analysis the medium and long-term perspectives, framework and considered possibilities of sustainable development of RTB "Bor" (Copper mines in East Serbia) after consolidation in the period of transition. The copper mine was opened in 1903. and today is the best quality copper producer on Balcan. This paper are elaborates the problems of privatization, debt, investment, growth of copper production from own mines (and imported raw), opening of new mines, economical efficiency of production, markets, environmental problems and impacts of the recent industry consolidation. The RTB "Bor" is a serious hot spot in Serbia. Unsustainable trends and processes are identified, as follows: open-pit waste dumps, flotation tailings, mining and processing waste waters, air pollution; no efficiency (excessive) using nonrenewal resource in the copper production; inefficiency in the use of energy, water and other inputs in copper complex; transboundary character of emissions of dust; environmental degradation and quality of wide area and ecologically highly risk, etc. Analysing some trends and planning-developmental perspectives and development strategies of company, it might be assumed that in the forth coming period, in parts of the Serbia, the borders areas of Bulgaria and Romania, there is an anticipated increase of ecological risk.

Jan 1, 2007

By L. H. Banning

Recent dry-top electric smelting tests at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., indicate that a high-titanium slag and a good grade of pig iron can be produced from alluvial Idaho ilmenite. A total of 120 tons of concentrates were smelted during this investigation, to yield an average of 0.5 ton of slag and 0.3 ton of pig iron per ton of ilmenite. Power consumption averaged 1,400 kv.-hr. per ton of ilmenite, at a feed rate of 400 to 500 pounds per hour, when operating at an electrical energy input of 290 to 370 kilowatts. The optimum operating voltage appeared to be 110 volts, phase-to-phase. Graphite electrode consumption averaged 15.6 pounds per ton of ilmenite smelted. Magnesite furnace refractory withstood the corrosive action of the hot metal and slag better than carbon refractory.

Jan 1, 1955

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983

By Ricardo Gaviria, Vincinte Acosta

There are major blast design and field procedures differences between conventional blasting in horizontally bedded coal seams and blasting underneath coal seams in a multi seam deposit with seam inclinations of 14 degrees or more.

Jan 1, 1995

By S. S. Rowland

Good afternoon, ladies and gentlemen. It is a pleasure, for several reasons, to be here at this 13th International Conference on Ground Control in Mining. Of course it's always a pleasure to be able to see and reacquaint myself with many long-time friends; but it's also a pleasure, or 1 should say worthwhile, because I take something back with me, some knowledge about mining that lets me do my job better and more safely. if I can do that, I've accomplished my purpose in being at a conference such as this. This conference is a little different, though. I have to earn my stay. I have to earn it by telling you a story; a story about mining through a mile of rock to get from one coal seam to the same seam on the other side of an ancient river channel; a story about mine personnel taking over the job from a contractor; a story about having to mine through two faults after the hard part was supposed to be over, but, most importantly, it's a story about how it was accomplished successfully and safely by a group of ordinary coal miners possessed with determination, belief in themselves, and a "can do" attitude. If you can take any part of my story and use it to do your job better and more safely, then I will have accomplished my purpose in being here today. Kerr-McGee Coal Corporation's Galatia Mine is located in Southern Illinois near the town of Harrisburg in Saline County, about 350 miles south of Chicago and 120 miles southeast of St. Louis. Construction of the mine began in 1982, and the first coal was shipped in 1984 from the Harrisburg No. 5 Seam, 550' below the surface. Mining began in the Herrin No. 6 Seam, 100' above the No. 5 Seam, on April 1, 1985. Mining in both seams began by using the room-and-pillar method. In 1989, the No. 6 Seam was converted to longwall mining, as was the No. 5 Seam in 1992. Today, all mining is done by the longwall method except for the required development work, which is performed by continuous miners. A heavy-media preparation plant with a 4.2 million-ton annual clean-coal capacity processes the coal. By the end of 1994, with annual production now exceeding 4 million tons, we will have shipped over 30 million tons of steam and metallurgical coal throughout the United States and the world. Most of the coal has been used as the primary source of fuel to generate electricity for the city of St. Louis. The No. 5 Seam coal can be used as a semi-soft coking coal or as a high-Btu, relatively low-sulfur steam coal. Its use allows utilities to comply with Phase I of the Clean Air Act Amendments of 1990 without installing flue gas desulfurization units or blending with other coals. The Herrin No. 6 Seam is a high-Btu, medium-sulfur steam coal that requires blending to meet Phase I requirements. Because the No, 6 Seam coal does not meet the Clean Air Act Amendments' Phase I compliance standards, we were forced to cease mining operations in the No. 6 Seam, leaving 170,000,000 tons of minable coal in the ground. Last month the Galatia Mine became a single-seam operation mining the Harrisburg No. 5 Seam only. The Clean Air Act Amendments of 1990 and the resultant S02 emission limitations on electrical power generation plants effectively eliminate, beginning in 1995, the near-term potential for profitable mining of the Galatia Mine's high sulfur Herrin No. 6 Seam coal. Because of the Clean Air Act Amendments, it is virtually impossible to market high-sulfur coals like the No. 6 coal unless the mine location and mining conditions enable greatly depressed sales prices to cover costs. We, along with the majority of

Jan 1, 1994

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By Jos. R. Guiteras

This paper is one of a series published by the Bureau of Mines on mining and milling methods and costs. It describes operations in the Alma district of Colorado in September 1937, supplemented by some additional data collected in July 1938. ACKNOWLEDGMENTS The author wishes to express his appreciation of the friendly cooperation extended him by the mine operators in the district. The greater part of the information was obtained from mine and mill superintendents to whom individual acknowledgment is made in the text.

Jan 1, 1940

By R. L. Brown

This report, summarizing the Bureau of Mines research and technologic work on coal and coal products for the period July 1, 1950, to July 1, 1951, is based largely on publications issued during the year. The sixteenth in an annual series, it gives footnote references to publications giving further details of the research and technologic work described, except in a few cases where research data presented herein has not been published previously. During the year, the national fuels situation was generally one of plentiful supply.3/ Mineral-fuel resources appeared adequate for several hundred years at reasonably increasing rates of supply. Coal-production capacity was in excess of demand; petroleum supplies were adequate; and natural gas use was limited only by pipeline capacity. However, it was pointed out that a world war would drastically change this situation of relative plenty, particularly with regard to supplies of petroleum and its products. Conversion to the use of coal on a large scale would be required, and improved methods of mining and of processing and using coal in solid or fluidized form or converted to liquid fuels could materially contribute to our national safety.

Jan 1, 1952

By Miguel Rutti

El presente trabajo señala la geología, litología y mineralización del yacimiento minero El Tapado del distrito Yanacocha, situado al norte de Cajamarca. Este se encuentra conformado por diferentes depósitos auríferos epitermales de alta sulfuración, los cuales se desarrollan dentro de un vulcanismo calco-alcalino de composición andesítica a dacítica de edad Mioceno y son correlacionables con la Formación Porculla del Grupo Calipuy. La geología del depósito está conformada por rocas porfiríticas (intrusiones) y flujos piroclásticos tales como tufos de cristales, tufos líticos y brechas piroclásticas afectados por eventos eruptivos de brechas freáticas - freatomagmáticas. Todas estas rocas han sufrido posterior alteración hidrotermal con ensambles típicos de sistemas tipo ácido-sulfato. La mineralización económica está controlada por procesos hidrotermales y se encuentra asociada a sílice masiva y sílice vuggy ( 1-10 g/t Au y estructuras de hasta 136 g/t Au ) y en menor grado sílice alunita y sílice granular (moderada a baja ley).

Apr 22, 2003

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005

By Peter Moser, G. Reihholf

Holcim, one of the world's leading suppliers of cement, aggregates and concrete, has set up a few years ago a working group “Quarry” in order to optimize the performance of its central European quarry operations in terms of work safety, environmental standards and economic performance. One of the activities of this working group "Quarry" addresses the subject of blast fragmentation in the quarries. A benchmark study of the blast work in all quarries has shown substantial differences for the various operations in terms of drill& blast costs. Especially big differences were found with respect to the drilling patterns as a function of the borehole diameters and with respect to the utilization of the borehole volume for charging the explosives.

Jan 1, 2006

By J. E. Kogel

Industrial minerals play a central and dual role in the sustainable development (SD) of natural resources. Over the past decade the mining industry has increasingly focused on sustainably extracting and processing industrial minerals. This trend has been driven by higher energy costs, diminishing water resources and sensitivity towards environmental stewardship. Industrial minerals have been used throughout human history as low cost, naturally occurring, materials. Today they are critical components of recycled packaging, energy efficient building materials, light weight paper coatings, and other products critical to the responsible utilization of global resources. As industrial minerals become more widely used in ?green? products, mining companies have established best practices for the sustainable management of industrial minerals mining and processing. These management practices include reducing energy consumption, minimizing water usage, increasing waste recovery through recycling and process optimization, and maximizing the amount of ore extracted per acre of disturbed land. With the commitment to SD principles, quantitative methods for objectively measuring SD performance have become increasingly important. Measuring sustainability impact is a valuable tool for effectively applying SD principles and for making choices that balance sustainable development against other business objectives. SUSTAINABLE DEVELOPMENT AND MINING Sustainable development is a term that has become a common part of our lexicon; however, it has multiple meanings and interpretations leading to a sometimes confusing and contradictory array of definitions. The absence of a single, precise definition reflects the fact that SD is a broad concept or paradigm that offers guiding principles as opposed to a specific set of criteria or regulations enforceable by government or other oversight agencies. While a principle based conceptual approach allows businesses to broadly apply SD practices that are tailored to their specific situation, it has also led the public to sometimes view voluntary corporate SD programs with a degree of skepticism (Walker and Howard 2002). This is particularly true in the mining industry. One reason for this skepticism is that the relationship between SD and mining is misunderstood and to many, sustainably developing non-renewable mineral resources is a contradiction (Rajaram et al. 2005). However, this view takes a very narrow interpretation of the tenets of SD. The second is that mining carries a legacy of poor environmental stewardship that does not accurately reflect current corporate environmental practices Many minerals companies have adopted the Brundtland Comission?s definition of SD (United Nations 1987): ?? development that meets the needs of the present without compromising the ability of future generations to meet their own needs?. This definition is very broad and can be interpreted in a number of ways. It provides a general context for sustainable development and is not intended to provide detailed guidelines addressing specific aspects of sustainable development. To fill this gap the following SD principles were drafted by the international minerals community in 2003 (ICMM 2003): 1. Implement and maintain ethical business practices and sound systems of corporate governance. 2. Integrate sustainable development considerations within the corporate decision-making process. 3. Uphold fundamental human rights and respect cultures, customs and values in dealings with employees and others who are affected by our activities. 4. Implement risk management strategies based on valid data and sound science. 5. Seek continual improvement of our health and safety performance. 6. Seek continual improvement of our environmental performance. 7. Contribute to conservation of biodiversity and integrated approaches to land use planning. 8. Facilitate and encourage responsible product design, use, re-use, recycling and disposal of our products. 9. Contribute to the social, economic and institutional development of the communities in which we operate. 10. Implement effective and transparent engagement, communication and independently verified reporting arrangements with our stakeholders. These guidelines insure that SD concepts are applied equally across the industry while setting a clear performance standard and benchmark against which to evaluate success. By adopting these principles and issuing the Milos Statement (http://www.sdimi.org/milos_decl_October%206_2003.pdf), which provides a more detailed vision for integrating SD into everyday business operations, the minerals industry has embraced SD as a core corporate value. The unifying and holistic approach embodied in SD principles impacts the entire mine to market life cycle and addresses the economic, environmental and social consequences of mining. INDUSTRIAL MINERALS The world economy relies heavily on minerals; they are essential to economic prosperity and the quality of life. Industrial minerals are non-metallic, non-fuel minerals that provide the raw materials for a vast range of products used in most every aspect of daily life. They are mined and processed worldwide and they span the spectrum from relatively low value, high volume commodities (e.g. common clay, crushed stone) that are usually mined locally to high value, low volume specialty materials that are sourced from unique one of a kind deposits (e.g. barite, talc, mica). High volume commodity mining operations are often located near the end use market which, in most cases, means areas of high population density where construction and other urban activities drive demand. In these situations the strict adherence to SD principles is particularly critical as these are highly visible operations that must meet the public?s demand for good corporate citizenship. These operations are similar to chemical or other manufacturing facilities that operate near population centers. In contrast, some mining operations are located in remote but environmentally sensitive regions of the globe where the pressure to mine sustainably is driven by the need to preserve habitats and other

Jan 1, 2009

By R. R. Klimpel

"SYNOPSISA discussion of the importance of flotation rate in the analysis of mineral flotation is presented. In particular, the highly interactive nature of the flotation ""system"" is emphasized where there are components of chemistry, equipment, and operating conditions simultaneously involved. It is further shown that: 1) flotation rate must be measured in order to economically optimize the performance of an industrial flotation circuit, 2) that consistent patterns exist in both flotation rate and equilibrium recovery when changing various settings of the system components, 3) that knowledge of these patterns is necessary in order to avoid making system changes that are either self-compensating or dramatically re-enforcing in some particular aspect of performance, and 4) the rate related role of the chemistry component (e.g.frothers and collectors) is often much bigger than is sometimes realized (especially in a negative sense involving overdosing of reagents). INTRODUCTIONFroth flotation is widely usedl-6 in mineral beneficiation processes as a method for separating different types of finely divided solids present in a liquid (usually aqueous) suspension. The approach is based on the contacting of solids with upward moving air bubbles in an agitated vessel where the solids are exposed to chemicals (collectors) which create a condition favoring the attachment of a certain portion of the solids to the air bubbles. This selected portion is then removed in a froth stabilized by chemicals (frothers) and subsequently recovered from the flotation vessel. Depending on the settings of the various components of the flotation ""system"" (see Figure 1) it is possible to achieve a wide range of flotation performance."

Jan 1, 1984

More than 1,200 professionals from the global tunneling and underground space industries are expected to be on hand for the 2009 Rapid Excavation and Tunneling Conference to be held at Caesars Palace in Las Vegas, NV. The conference, set for June 14-17, is sponsored by the Society for Mining, Metallurgy, & Exploration, Inc. (SME) and the Construction Institute of the American Society of Civil Engineers. The four-day conference will feature more than 100 technical papers in 19 sessions. Two one-day short courses are also planned, as are a pair of field trips. And the show?s exhibit will feature more than 120 of the industry?s leading equipment and service suppliers.

Jan 1, 2009