Search Documents

By Winthrop F. Watts

The U.S. Bureau of Mines evaluated the performance of a catalyzed diesel particulate filter (CDPF) and a CDPF combined with a diesel oxidation catalyst (DOC) at two metal mines. This report describes the results from the two field evaluations. The CDPF-DOC was installed on a load-haul-dump (LHD) powered by a 175-kW, prechambered, turbocharged engine. This system reduced diesel particulate matter (DPM) concentrations by 71±28 pet, as determined by size-selective sampling with gravimetric analysis, and by 71±29 pet, as determined by respirable combustible dust (RCD) analysis at the vehicle operator's location. The CDPF was installed on a diesel-hydraulic, roof-bolting jumbo, powered by a 172-kW engine. The CDPF reduced DPM concentrations by 72±21 pet, as determined by size-selective sampling with gravimetric analysis, and by 62±25 pet, as determined by RCD analysis at the vehicle operator's location. Underground evaluation was more difficult because of frequent movement by the roof-bolting jumbo, variation in daily workload, tremendous fluctuation in ventilation airflow rates, and use of a high sulfur diesel fuel, which promotes the formation of sulfate particles, decreases filtration efficiency, and hastens the deterioration of the catalyst.

Jan 1, 2010

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By F. Grajales Muñoz

The Ciénega project, now under construction by Peñoles group, is located in the mountains of northwest Durango, Mexico. The gold and silver deposits are found in a 4-km (2.5mile) long system of veins. An underground operation will be built. The planned 1 kt/ d (1100 stpd) process plant will contain a countercurrent cyanide circuit for oxide ore and a flotation circuit for sulfide ore. Considerable resources have been devoted to the development of infrastructure in the isolated location, as well as for the mitigation of environmental impacts. Startup is scheduled for the third quarter of 1994. Ciénega’s ore bodies consist of quartz veins containing gold, silver, lead and zinc values. The vein thicknesses vary from 2 to 10 m (6.5 to 33 ft) with a northwest trend and nearby vertical dip. Veins are hosted in Tertiary volcanic rocks. The district has intermittently been explored since 1971 by Penoles. After the third series of diamond drilling and direct development work on vein, Peñoles decided to begin project construction.

Jan 1, 1994

To improve communications between mine workings and surface locations during emergency situations and for administrative purposes. The Approach: Development of a device for interconnecting phone systems which permits two-way communication between a public telephone and a mine pagerphone by authorized personnel. How It Works: The system, developed by personnel at the Bureau's Pittsburgh (Pa.) Mining and Safety Research Center, makes connections between the public phone line and mine pagerphone line. As shown in Fig. 1., incoming calls are sensed by the ring detector (4) and the system "answers" the call electronically. To reach the pagerphone system, the caller inserts an audible tone of fixed frequency through the microphone of his telephone. This tone is produced by a miniature, pocket-carried tone generator and is detected by a tone recognition circuit (5). When this hap-pens, relay, switching, and logic circuitry (6) closes the connections between the two phone systems. Simultaneously, a page activator (9) places a DC paging voltage on the mine phone line.

Jan 1, 1974

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By Eric S. White, Thomas J. Sabourin, Khuram R. Mohib

"This paper presents the challenges associated with the design and construction of a steel sheet pile cofferdam supported with one level of grouted anchors in clean to silty sand with gravel. The initial assessment of the subsurface conditions indicated loose to medium dense soil with intermittent dense to very dense layers with no occurrence of cobbles and boulders. Sheet piles were proposed to be installed to a depth of 24 m below the ground surface to limit dewatering requirements for the cofferdam. During sheet pile installation, refusal of piles occurred at multiple locations forming passages for increased flow into the cofferdam. Modifications were made in the design of the dewatering system as a result of the increased flow. Finite element modeling was used to select the necessary modifications to the dewatering system within the cofferdam. Wells were installed based on the findings of the numerical model. Model simulations showed good comparison with monitoring of the field installed dewatering system.INTRODUCTIONIt is necessary to consider the impact of the ground water, subsurface stratigraphy, strength, and drainage behavior of the soil for the design and construction of cofferdams. This paper presents a case history of the construction of a cofferdam in Northern Ontario, Canada. The project consists of the construction of a powerhouse, intake, and tailrace which will generate around 28 MW of renewable clean energy by diverting water from New Post Creek through a power house and discharge into the Abitibi River. The focus of this paper is the dewatering and excavation support required to permit construction of the powerhouse. The layout of the cofferdam is shown in Fig. 1. The cofferdam for the powerhouse is rectangular in shape with sheet piles on all four sides intended to be driven to the design toe El. 101 m. The east and west walls have a length of 46.3 m. North and south sides are 47.6 m long; and in addition, two cantilever sheet pile walls bound the tailrace on the west side and two cantilever walls were installed on the east for construction of the penstock inlet. The ground surface in the powerhouse cofferdam area, before commencement of sheet pile driving, was brought to El. 125; the ground then slopes up to the East, toward New Post Creek, and the site is bounded on the West by the Abitibi River. 186 pairs of sheet piles were used to create the cofferdam and cantilever walls. The deepest excavation is to elevation 114.4 m. Within the west half of the cofferdam footprint, the base of excavation slopes upward at 3H: 1V to facilitate the tailrace discharge into Abitibi River.SOIL STRATIGRAPHYThe cofferdam design was based on the geotechnical investigation conducted by AECOM (2014) which included two relevant boreholes near the powerhouse footprint. The ground elevation at the time of investigation varied between 131 to 129 m. The material observed to the full depth of investigation was comprised generally of coarse to fine sand and gravelly sand or a sand matrix with gravelly inclusions. Some intermittent layers of clay and silt intrusions were also observed. Generally the soils grade finer away from the river. SPT N60 values were recorded in two borings during the field investigation with values reported from 3 to 92. The in-situ conditions ranged from compact to dense with some loose and some very dense zones. Figure 2 shows the variation in SPT N60 values with elevation."

Jan 1, 2017

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

By Behrouz Tehrani

The size, complex issues, and requirements to construct large number of tunnels, for a single project, expeditiously, and without exceeding the overall project budget, a program Construction Management (CM) team is highly recommended to be selected early during design process to provide guidance/direction relative to contract packaging and scheduling. This paper is not focused on the project itself, however, the emphasis is on experiences gained from the project. Wishing that some of the strategies described in this paper will be of value to owners of underground project.

Jan 1, 2008

By Javier Enrique Basurco Cayllahua

In this work, a gram-positive bacteria was used as biosorbent to elucidate the aluminum load capacity under different conditions related to metallurgical and chemical plants. The sorption data followed the Langmuir, Freundlich, Dubinin-Radushkevich isotherms. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Dubinin-Radushkevich model fits better the aluminum biosorption data. The maximum sorption capacity was found to be 41.59 mg.g-1. The maximum removal of aluminum was 95% at pH around 5. The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). This study indicated that the R. opacus is an environmental friendly biosorbent.

Jan 1, 2009

By Lyle Dennis

Emphasis on increased production while maintaining rigid quality standards has necessitated a change in blasting technology at Dacotah Cement's limestone and gypsum quarries. The following three methods implemented during the past three years have yielded an increase in production through improved fragmentation.

Jan 1, 1996

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

By M. E. Rossi

In mineral resources, geologic and mining data are acquired, processed, analysed, interpreted and modelled, eventually serving as basis to generate predictions and production plans. This is a complex process, and the resulting predictions are impacted by uncertainties related to the data itself and the processing methods and techniques used. They are also impacted by the subjective decisions made by the modeler(s) at each step of the way. Knowledge, biases, skills, and prior experience come into play in the long mineral resource evaluation development workflow. It is meaningless to discuss uncertainties without evaluating the associated risks that those uncertainties imply. It is important to quantify and assess uncertainty, and to evaluate and mitigate its consequences. This paper discusses (1) conceptual and practical sources of uncertainty; (2) the utopia of an “objective” uncertainty; and (3) the quantification and public reporting of uncertainty using geostatistical conditional simulations. The objective of this paper is to postulate that the industry is running out of reasons and excuses to ignore uncertainty and risk in project evaluation. This is done in two parts, with this, the first one, presenting a more conceptual discussion. Part 2 will present case studies from different types of mining projects and operations showcasing the impact that risk assessments can have in a mining project.

Feb 22, 2026

By D. Waite

The Chairman opened the session by wondering why so few papers on Maritime Structures had been received for this conference. Perhaps because the marine environment is so hostile and the access so difficult that engineers tend to be more prudent about new ideas and designs. Dennis Waite noted the number of grey hairs in the room - grey hairs which could be equated with experience gained the hard way. He hoped that this experience would be passed on in the discussion period of this session. The Chairman was delighted to welcome two authors from China, Mr Sun and Mr Liang. He was most grateful on behalf of the conference for their efforts both in preparing their papers and for being able to present them. He regretted that Messrs Noce and Fedolino were not able to present their paper and then welcomed Mr Christensen from Denmark who would present the first paper.

Jan 1, 1991

Jan 1, 1970

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977

The extractive industry has the potential to impact the health and well-being of workers, families and surrounding communities. In the current environment of social performance, project planning considers that activities should be conducted in the best environmentally, socially and economically acceptable way across the development cycle (i.e. from exploration ? post-closure). In this context, health impacts of mining can be mapped and extend over the Life of the Community and can encompass worker injury and disease, exposure to communicable and non-communicable diseases, and health outcomes specific to family and community health and well-being outside the fence. To contribute to an emerging field focused on Health and the Extractive Industry, this paper reviews and compares health activities extracted from social and environmental reports published by selected major mining, oil and gas companies with operations in Australia and Canada. The objective of this review is to map corporate approaches to public health management across our previously developed Life-of-Mine within Life-of-Community (LOMLOC) framework in order to identify and compare trends and behaviour in corporate health investments across the project cycle, as well as identify the level of prevention targeted by this investment activity (i.e. primary, secondary and tertiary prevention of detrimental health impact). With the extractive industry facing ongoing rapid growth worldwide, this paper provides preliminary comparative information about corporate health spending by some companies in Australia and Canada. This information serves as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.

Aug 1, 2013

By K. Awuah-Offei, A. U. Rehman

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis, in community engagement program, to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This paper proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies. INTRODUCTION The mineral industry provides raw material for industrial activity to support our society (Martens and Rattmann, 2001). Mines have changed conventional mining practices to sustainable ones because of the negative impacts of mining and increased public awareness (Wang et al 2016). The concept of sustainable mining is getting mature as stakeholders (e.g., governments, investors and host communities) are getting involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in failure to acquire social license to operate (Thomson and Boutilier, 2011). The social license to operate (SLO), if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO; ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomsan and Boutilier, 2011). Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 1, 2018