Search Documents

By A Kamkar-Rouhani

The paper describes a mineral potential mapping of gold and other base metals in Mahneshan area, Iran, using geographical information system (GIS), in which, the method of weights of evidence is used to combine spatial data obtained from different sources to make prediction for mineral potential. This is a quantitative tool for mineral resource mapping that can be used to delineate and predict favorable areas for further exploration by using the characteristics of known and similar mineral deposits. In accord with the descriptive model for gold and other base metal deposits, the spatial distribution of 20 known mineral occurrences was used. In addition, digital evidential maps were used in this study. The maps include maps of lithological units, faults and first derivative of total aeromagnetic data, remotely-sensing data of alteration and also geochemical evidential maps produced on the basis of the results of chemical analyses of samples taken from the stream sediments in the area, and analysed for Cu, Pb, Zn, Sb, As, Ag, Au, Ba and Hg elements. The binary maps were produced and then combined with the model of weights of evidence using 20 known mineral occurrences to obtain a final map of the favourable areas for further exploration of gold and other base metals in the study area. The final map is a predictive GIS model of the mineral deposits in the area. An interesting matter about the final predictive GIS model is that the faults are mainly located in favorable areas which possesses the most probability of mineralisation. Therefore, the faults in these areas have priority for further exploration of gold and others base metals.

Jan 1, 2005

By Don Novotny, Dana Spencer

In this workshop our intent is quite simple; that is that we will introduce a relatively new technology that may have applications in blasting applications. This technology is the laser initiation of explosives. This workshop course is not intended to suggest ways in which specific blasting problems can be resolved. That is the purview of experts within each of your fields.

Jan 1, 1994

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

By Moinpour M

The kinetics of reduction of copper (cuprous) sulphide with CO-CO2-He gas mixtures, using an excess of CaO(s) as a sulphur-scavenging substance were investigated in the temperature range 855° - 950°C by a thermogravimetric method. Several gas compositions were employed at each temperature. Potential carbon deposition was overcome by preheating the reducing gas mixture. The phase-composition and the morphology of partially reactedsamples were analysed by a SEMlEDAX unit. The reduction rates showed strong dependence on the bulk gas compositions (CO, CO2) and, in most cases, the rate declined with rising temperature. The rate-controlling step appears to be the diffusion of CO2 gaseous species through the micropores of the CaS(s) - product layer which builds up around the CaOcore.

Jan 1, 1989

By Howard A. Perko

Soldier pile and lagging is a conventional means of temporary excavation shoring. Timber lagging design has traditionally been based upon the designer's experience or empirical rules. One such method is the Goldberg Zoino chart used by the Federal Highway Administration. Most of these methods restrict the designer to a consistent soil profile, certain pile spacing, construction grade timber lagging, and limited depth. The methods do not take into account surcharge loads or a variety of other factors that could arise. A designer working outside of ordinary circumstances with unusual loads, varying soil conditions, or alternate lagging materials has difficulty estimating lateral earth pressures. In rigid earth retention systems, lateral earth pressure is generally assumed to be constant along the length of the wall. In soldier pile and lagging systems, the lagging is often considerably less stiff than the steel soldier piles. As the lagging deflects, the soil tends to bridge between the stiffer elements resulting in a lower pressure on the lagging. Several previously published methods by others for determining this reduced pressure are summarized and discussed. These methods typically consist of using a portion of the active earth pressure in several different pressure distributions. A simple theoretical model is presented for determination of lateral earth pressures on wood lagging. The model is based on a three-dimensional "silo" shaped sliding wedge analysis. Results of the model are compared with other published methods. The model compares well with these methods which cover the normal spectrum of design situations. In addition, the model can be used to estimate lateral earth pressures outside typical situations.

Jan 1, 2008

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

This paper is intended partly as a summary of the conclusions that have been arrived at by various authorities on this matter, and also with a view to initiate some discussion on the subject, especially as most of the quartz gold mines in Victoria are operated without having any proper assay plans or any idea of the real values other than those given by the mining managers, who, from experience in the particular cases, are supposed to be able to arrive at a correct idea of the true values of- the ore, and, in many cases, oppose any other methods than their own, holding the view that no sampling is equal in correctness to the bulk sample of the battery. The necessity of properly sampling and estimating the ore in a mine in every case, perhaps hardly needs to be urged on the members of the Institute, but is not, apparently, so obvious to others.It is proposed to confine this paper to the sampling of ore reserves in a mine, and the various points which have to be taken into consideration in arriving at values, from the assayer's point of view, leaving the methods of sampling metallurgical products out of consideration for the present. "It is advisable to define" ore reserves" as ore exposed on three sides at least, and accessible to the sampler on all three. "Prospective ore" would include all ore not so fully exposed; but which may, from the nature of the case, and the geological conditions prevailing, be reasonably supposed to exist.

Jan 1, 1904

By A. A. Sadegh

A laboratory investigation was carried out on the characterization and beneficiation of sillimanite ore. Petrographic analysis indicated that the ore consisted of massive elongated sillimanite grains in a matrix of hematite, garnet, feldspar and silica. A procedure for estimating the percentage of sillimanite was developed using float-sink and magnetic-separation techniques. A liberation study was carried out to determine the level of size reduction required to achieve sufficient liberation while ensuring that gravity concentration techniques would be applicable. Laboratory testing was performed on the liberated ore to investigate the applicability of using wide-angle dense-medium cycloning to upgrade this ore. Initially, medium-only tests were carried out using various size distributions of magnetite and ferrosilicon as the dense-medium solids to evaluate the effects of operating conditions on medium segregation. Depending on the medium solids and operating conditions, either positive of negative differentials (difference between the relative densities of the underflow and overflow streams) were obtained. Based on these results, separation tests were performed to process nominal -1.2-mm sillimanite ore. The results indicated that sillimanite concentration could be obtained using a medium relative density that was much lower than would typically be used in a dense-medium cyclone separation.

Jan 1, 2007

By T. Gerritsen, R. C. Delgado, J. Janzen, E. R. Veloza

The paper describes the components of an Integrated Furnace Control system for covered-arc (shielded arc) smelting with results from the recently started 75 MW Cerro Matoso Line 2 Furnace. The paper starts with a review of the mechanisms of power and feed input and heat losses in the shielded-arc smelting process, and describes how the details of the control system are tailored to the process. The control modules of a covered-arc smelting furnace are described including measured results and screen captures. This paper focuses on Integrated Furnace Controls tailored to shielded-arc smelting, but similar approaches have been recently applied to other furnace processes including immersed-arc smelting.

Jan 1, 2004

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

By D. Allan Coutts

Demonstration projects using hydrogen as a fuel are becoming very common. Often these projects rely on project-specific risk evaluations to support project safety decisions. This is necessary because regulations, codes, and standards (hereafter referred to as standards) are just being developed. This paper will review some of the approaches being used in these evolving standards, and techniques which demonstration projects can implement to bridge the gap between current requirements and stakeholder desires. Many of the evolving standards for hydrogen-fuel use performance-based language, which establishes minimum performance and safety objectives, as compared with prescriptive-based language that prescribes specific design solutions. This is being done for several reasons including: (1) concern that establishing specific design solutions too early will stifle invention, (2) sparse performance data necessary to support selection of design approaches, and (3) a risk-adverse public which is unwilling to accept losses that were incurred in developing previous prescriptive design standards. The evolving standards often contain words such as: ?The manufacturer shall implement the measures and provide the information necessary to minimize the risk of endangering a person?s safety or health.? This typically implies that the manufacturer or project manager must produce and document an acceptable level of risk. If accomplished using comprehensive and systematic process the demonstration project risk assessment can ease the transition to widespread commercialization. An approach to adequately evaluate and document the safety risk will be presented.

May 1, 2007

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

The purpose of this paper is to outline some aspects of the experimental worlr that has been carried out in the mineral dressing laboratory at M'ount. Morgan during recent years.The subject matter has been dealt with under the following headings:1. Comminution of various mill products.2. The application of sulphur dioxide as a flotation reagent.3. Heavy-media separation.4. Bulk flotation of sulphide ores.COMMINUTION OF VARIOUS MILL PRODUCTSThe following data were cbtained by processing fractions of reserve grade ore.Granular TailingIn Table 1 are shown the results of tests on material representative of average grade tailing. In the first test (H1 ) the granular tailing was floated as received and in the second test (Ha) the tailing was ground prior to flotation.

Jan 1, 1952

[ ]

Jan 1, 2009

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992