Search Documents

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Walker G. S

A study of the crystalline materials on or near the surface of freshly made or "green" superphosphate granules and mature, "set" superphosphate granules was undertaken using X-ray diffraction, X-ray mapping, scanning electron microscopy and electron probe micro analysis techniques. Calcium sulphate (CaSO4), calcium sulphate hemihydrate (CaSO4 1/2H20), and mono calcium phosphate monohydrate (Ca(H2PO4)2H2O), were the only crystalline species present in the "green" superphosphate.In the set superphosphate however, additional compounds were present, namely complex iron and aluminium phosphates Ca(Fe,AI) H(HPO4hF2)2H2O, (Fe)3(H3O)H8 (PO4)6H2O and calcium sulphate dihydrate (CaSO4.2H2O).The complex phosphates tied up the major part of the Fe and Al in the system and were concentrated on or near the surface of the granule. An intimate mixture of CaSO4.2H2O, and CaSO4, along with the above mentioned complex Fe-AI compounds, crystallize close to the surface of the granule and cause the setting of superphosphate that takes place during storage.

Jan 1, 1980

By John Durkin

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the sig-nal amplitude as a function of source type, source depth, and horizontal off-set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the system, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will be detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By Christian Maguire

Tunnel contracts in New York have in recent years had few bidders with the bids received being much higher than anticipated. Since 9/11, security has become a key issue in planning key infrastructure projects in New York. This is especially true in the case of large water supply tunnels. Striking the right balance between cost and security was the major factor in determining the best configurationfor the Kensico-City Tunnel. This paper outlines the efforts made to determine realistic probable bid costs for the tunnel contracts, and the innovative approaches taken to deal with security issues.

By Henry M. Harris

A study was made by the Bureau of Mines to determine if shapes of oxide-glass compositions could be roll-formed at high temperatures, and to find the conditions required for adequate formability. A unit with directly connect' furnaces and heated rolls that allowed forming of most of the compositions developed. Glasses of the feldspar type were chemically unreactive with the alumina grains, and allowed the best roll forming. Optimum forming was attained at temperatures of 1,400° to 1,530° C, with compositions containing 30 or 40 percent feldspar and 60 or 70 percent alumina. Formability was better when compositions contained minus 325-mesh materials, rather than coarser or finer powders. In many cases, roll-formed shapes had physical properties equal to or better than the normally sintered shapes of the same composition.

Jan 1, 1967

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By A. McLean, M. Barati

In this paper, examples are presented of pyrometallurgical research and associated teaching activities during the past century within the Department of Metallurgical Engineering, now the Department of Materials Science and Engineering, at the University of Toronto. Throughout these years, pyrometallurgical research has been characterized by recognition of the importance of the interdependence of measurements and models as well as the development and application of sensors, for the generation, validation and practical implementation of new knowledge. The important role played in the delivery of lectures and participation in joint research by Adjunct Professors with strong backgrounds in the pyrometallurgical industry is described. Projects conducted in close collaboration with the industrial sector and opportunities for students to obtain practical experience working as teams on a "round-the clock" shift basis within an industrial pilot plant environment are outlined. These activities, together with the involvement of students in poster competitions and the presentation of papers at society conferences and technical meetings, are still vital elements in the development of pyrometallurgists equipped with the appropriate professional skills for subsequent employment within academia, government laboratories or the industrial sector.

Jan 1, 2015

By D. Kolymbas

A simple formula is introduced which allows the evaluation of dynamic pile tests. The following case is considered: The pile top is dynamically loaded by an impact. The velocity v of the pile top is recorded over the time. Let v1 and v2 be the first and the second maximum of this curve. Then, the pile bearing capacity (resulting from ideally plastic resistance at the pile wall and at the tip) can be set approximately equal to Z(v1- ½ v2), where Z is the impedance of the pile cross section. Due to the assumption of ideal plastic resistances, radiation damping needs not be taken into account. Material damping may be important in rate sensitive soils (such as clay, even if it is highly overconsolidated). A simple correction procedure for material damping is proposed.

Jan 1, 1989

By R. V. Ramani

This volume, the first of a six volume final report, provides an executive summary of the research and results carried out under a grant from the U. S. Bureau of Mines on underground coal mine ventilation. Under the project, a mine ventilation simulator was developed. Sensitivity of leakage and friction factors on the total quantity and pressure requirements was studied. The simulator was applied to a new mine under development, and to an operating mine, to demonstrate the usefulness of the simulator in ventilation planning and in evaluating proposed changes to existing ventilation system. The titles of the other volumes are as follows: Volume II: Mine Ventilation Network Theory Volume III: User's Manual for PSU/MVS Volume IV: Sensitivity of Leakage and Friction Factors Volume V: Application of PSU/MVS to Ventilation Planning of a New Mine Volume VI: Application of PSU/MVS to the Analysis of Modifications to Existing Ventilation Systems

Jan 1, 1977

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By Ovidiu Pasca

The Phelps Dodge Miami Smelter utilizes four Hoboken converters to process molten matte from the Isasmelt vessel. This paper presents past and present improvements in operation, maintenance and process optimization, based on data collection, which has led to increased converter campaign life and copper throughput.

Jan 1, 2005

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By Manish Kumar Jain

The mineral industry in India is an important contributor to the country?s GDP and foreign trade, and also a significant source of employment generation. The industry is distributed almost all across the country and has operations in some of the remotest areas, where it has also served as a sole source of infrastructure development. India produces 89 minerals, out of which four are fuel minerals, 11 metallic, 52 non-metallic and 22 minor minerals. The mining leases are occupying about 0.21% of the total land mass of the country. Indian mining industry is characterized by a large number of small operational mines (approx 3000 mines). Appropriate systems have been put in place to ensure sustainable growth of the sector, which include formulation of procedures for scientific prospecting and mining and development of a mechanism of prior environmental and forest clearances for mining projects. Main emphasis is to protect the health and safety of mine workers, as well as to safeguard the interests of indigenous people through rehabilitation and resettlement packages. Efforts are under way to mainstream the artisanal and small-scale mining sector in order to promote equity in the mining industry. The issue of scientific closure and reclamation of the abandoned mine sites poses a major challenge. Present paper illustrated several initiatives have been taken in this direction along with case studies, which could be replicated in other parts of the country.

Aug 1, 2013

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By Tom Tallone

In the majority of metal and nonmetal mining operations, narrow vein deposits are being mined with slusher hoists. Thin; method of mucking is costly, due in part to its inherent labor intense operation and to its inability to muck 100 pct of the deposits. Mechanized equipment would greatly improve the material handling in narrow vein mining and would dramatically reduce the operational cost. The Compact Loader/Trammer, known as the "mini-mucker" has been developed to increase productivity of the load/haul/dump portion of the typical narrow vein mining cycle. This is Volume II of the final report and concerns the operation and maintenance of the mini-mucker. Volume I covers a general and design review of the activities on the subject contract and are available under separate cover.

Jan 1, 1985

By Stacy Loizeaux

The Beirut Hilton Hotel, which was built in 1975, but never occupied, was imploded on Sunday, July 14, 2002 by Controlled Demolition, Inc. (CDI) of Phoenix, Maryland and their client, Optimal Engineering Consulting & Contracting, SARL, (OECC) of Antelias, Lebanon to make room for a new hotel. Twenty-seven years ago, just days before the grand opening, the Hilton Hotel became the site of fighting in Lebanon’s Civil War. Christian and Muslim militiamen fought room to room for control of the building and other nearby hotels. The Hilton, two other major hotels and other high-rise buildings were ravaged by the fighting. The building was one of the three major hotels badly damaged, but not rebuilt, in Lebanon. Located in the City Center, the Hilton stood out in a major redevelopment area which, in recent years, had erased the scars of the 15 year long Civil Wa r.

Jan 1, 2003

By Thomas. L. O.

Apart from a few sketches and incomplete maps, mainly topographical, and one or two detailed maps of placer-creeks, there is little information on the topography and geology of most of the country adjacent to the sections of the Alaska Highway in the Liard River area, particularly that part east of Kechika river. In 1943, the Geological Survey of Canada made a recon-naissance from Fort Nelson clown the river of that name to the Liard, thence up the latter to Hell Gate, and also up Beaver river for a distance of fifty miles. The whole of the area covered was found to be underlain by sedimentary rocks, not a single igneous dyke being seen. The British Columbia Department of Mines began reconnaissances near the highway both in and north of the drainage basin of Prophet and Muskwa rivers with a view to finding structures favourable for the accumulation of oil. In Liard River valley near the mouth of Smith river and at intervals from there clown to Devil' s Portage occur warm springs whose character and origin are not definitely' known, since they have not been investigated (21, p. 38A). Similar springs are said to occur at several localities over a broad belt extending from Muskwa river across the Liard to the Nahanni River country (26, p. 11). On Liard river below the mouth of Dease river, stratified sands, gravels, and clays of Pleistocene (?) age are constantly met with and in one or two places are underlain by sandy clays. The distribution of the latter, however, is very limited in the section cut by the river west of the Rocky mountains. The only range of these mountains that reaches the Liard is the high limestone ridge which approaches the mouth of Vents river from the southeast and then almost vanishes a few miles to the northwest of it (27, pp. 43-45). In general, the ranges of the Rockies in the area under consideration have been but little explored, but they are undoubtedly very largely sedimentary and, with the exception of some volcanics and intrusives on their western flanks, are probably almost entirely so. Unlike the high, deeply incised ranges in southern British Columbia, they dwindle in elevation north of Terminus mountain to low-wooded ridges separated by wide swampy valleys, and practically lose their identity between it and the Liard. The foothills, which, along the Liard, have a width of 38 miles (from near the mouth of Trout river to Hell Gate) are composed of a great series of alternating shales and sandstones, with some limestones, all folded closely together, which resemble those found in the foothills farther south (27, pp. 50, 19-20).

Jan 1, 1944

By L. K. Witika, J. H. Masinja

"Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. Of the six frothers tested, two came from the alcohol family, two from the glycol family and last two were formulated products. The initial work involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. For froth stability tests, six frothers were tested on a two-phase (water–air) system using the Bikerman column flotation cell, while water recovery tests were conducted using a total of seven frothers, including the standards for each plant. The results of the testwork showed that (i) although a stable froth is essential for optimum recovery of valuable minerals, a higher molecular weight frother, like Dowfroth 250, caused poor selectivity when used on fine ores and (ii) a lower molecular weight frother was suited for Lumwana ore, while a mid to higher molecular weight formulated product was suitable for Kansanshi sulphide ore. INTRODUCTION Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. The initial work of this project involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. In order to investigate the gangue entrainment levels in the Lumwana and Kansanshi sulphide ores, two well-known methods (froth stability and water recovery) were used. Firstly, froth stability tests were conducted using six frothers, two from the glycol family (Dowfroth 200 and Dowfroth 250), two from alcohol family (MIBC and pine oil) and other two from the formulated family (Betafroth 20 and Betafroth 245), at the University of Cape Town’s Centre for Mineral Research (CMR) laboratories. Froth formation and stability measurements were conducted using the Bikerman column flotation cell."

Jan 1, 2015

Jan 1, 1988