Search Documents

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins' and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer' type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964

By F. Cadena, Fred C. Bond, Walter L. Maxon

Grinding is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grinding installations. There have been some tests published, notably those of Lennox,' which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the comparisons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to be expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method. For example, let it be assumed that an ore to be tested consists of equal parts of difficult grinding mineral and easy grinding mineral. This is to be compared with an ore used as a standard, and consisting of minerals which are all of about the same grindability. If a comparison

Jan 1, 1935

By A. G. Guy

Thermodynamic activity rather than chemical composition is basic to the analysis of diffusion. This is the essential conclusion reached by Darken1-3 and by Birchenall and Mehl.4 If so, it is reasonable to expect that diffusion calculations should be carried out using activities. This paper will illustrate a method of employing activities in analyzing interstitial diffusion. For interstitial diffusion (of carbon in iron and probably generally) the diffusion of the solvent atoms, volume changes, and other such complexities not explicitly provided for in the usual diffusion equations cause a negligible error of the order of 1 pct. Therefore it is relatively easy to test the validity of an analysis based on activities in the instance of interstitial diffusion. The mathematical treatment of the more complex substitutional diffusion could be simplified once the adequacy of the activity method had been established for substitutional diffusion. Thus the present work has the purpose not only of providing a superior analysis of interstitial diffusion but also of indicating a possible approach to the more important question of an adequate treatment of substitutional diffusion. Development of the Diffusion Equation Although activities are convenient quantities to determine experimentally, they are derived from the more fundamental fugacities.9 Possible confusion in using activities can be avoided by basing equations involving their use on the relationship, dP = -D1d/ax dt [I] where, dP = the number of grams of solute crossing one cm2 in the time dt sec. D, = the diffusion constant for use with fugacities; it is assumed to be constant at a given temperature, and has units of secs. f = the fugacity of the solute in the solid solution; the units are those of pressure, dynes per cm2. x = the distance in cm. Eq 1 can be considered to be the basic form of the first Fick Law for one-dimensional diffusion. In order to convert Eq 1 into an equation involving activities, a choice of a standard or reference fugacity, f°, must be made: then. a = f [2] where a is the activity corresponding to the fugacity f. However, the value of a is also determined by the relation, a = a\c [3] where a is the activity coefficient and c is the concentration. For a given value of a (such as a = 1) it is evident that the units used for expressing concentration will affect the numerical value of a corresponding to a given amount of carbon dissolved in y-iron. Since weight per cent concentration is so widely used, this unit will be adopted as the standard in this paper. When the value off given by Eq 2 is substituted in Eq 1, the first Fick Law becomes, dP= -D,f°dl [4] Since D,f° is constant (at a given temperature), the second form of Fick's Law can be obtained in the usual manner, -dt D'f° dx [5] where c' is the concentration in g per cm3. In terms of weight per cent concentration, c, Eq 5 becomes, dc _ 100 d2a Tt = T /f w [6] where p is the density of the solid solution and will be assumed to be constant. In order to simplify Eq6, it is necessary to consider the standard state, f°. Standard states are chosen for convenience. There appears to be one especially convenient choice for the analysis of interstitial diffusion. If the activity coefficient, a, is set equal to unity at infinite dilution of the solute, 100 then — 100D1fl° is approximately equal P to the usual diffusion constant in dilute solutions. This is true since the activity, a, in Eq 6 can be replaced by the concentration, c, with little error in an infinitely dilute solution.* Here f1° is the standard fugacity necessary to achieve this standard state. It is proposed that a diffusion constant Da' be defined, Da1=100/pD1f1° [7] where A is the metal whose diffusion is * The second derivative of a is equal to the second derivative of c in dilute solution only if -da/dr- is. zero. Although theory does not require this condition, in the systems C in Fe, and Zn in Cu, dc is in fact found to be essentially zero.

Jan 1, 1950

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By Robert P. Koenig

FOR the first time other than on occasion of war the people of the United States are experiencing full-scale participation in world affairs. Public concern has seldom been so involved with conditions and events beyond our own continental limits. Our interest is not wholly of recent origin. Over the years the activity of the United States as a world power and an important trading nation brought about the widening of our political interests and the progressive interrelation of our economy with that of the rest of the world. Some may see in our present phase of world-wide activity the natural consequence of our continued growth. Such observers must also be aware that within recent years our importance in world affairs has been considerably increased. For within the space of an extremely short period events have occurred that have literally jet-propelled the United States into the role of a leading participant in the conduct of world affairs. Little of the choice of this role was left to us. The decline of power in western Europe, the ascendancy between the Elbe and the Pacific shore of an obviously antagonistic force, our earnest endeavor to secure international control of atomic energy, the necessity of providing relief and rehabilitation to war-ravaged areas, and the police work that must be done in occupied territories are problems which have risen in great measure without our help-but they cannot be solved without it.

Jan 1, 1948

By M. TAYLOR

AT Grand Saline, some 65 miles east of Dallas, the Morton Salt Co. of Chicago has for some years operated a brine pumping and evaporation plant on a salt dome. They recently drilled trial holes to obtain data on the dome, preparatory to opening, a new mine, with the following results: The dome is in the form of a truncated cone, with an average of 210 ft. of cover. The top of the dome is approximately one mile in diameter, with the town of Grand Saline lying over the northern rim, and the sides slope off at an angle of 50" to 80" from the horizontal. The deepest holes were drilled to 900 ft. without penetrating beyond the salt, and indications are that the salt deposit is several thousand feet thick. As the deposit increases in area with the depth, there is undoubtedly enough salt to supply a mining operation for an almost unlimited period of years.

Jan 1, 1930

By AIME AIME

ALTHOUGH the present economic depression is felt in the petroleum industry, probably as much as in any other branch of American industry, the Petroleum Section of the Institute was well represented at the general sessions on Monday and at all of the seven division sessions on Tuesday, Wednesday and Thursday. The seven sessions of the Division were so arranged as not to conflict and thus permitted members to hear the programs of all sessions.* The first meeting of the Petroleum Division was held on Tuesday afternoon; a joint session on engineering research and production engineering. The following papers were presented:

Jan 1, 1931

By H. H. Stout

IN the early fall of 1925, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point, The apparatus consisted of a vertical 1-in. dia. silica tube about 12 in. long, heated on the outside, The cathodes were broken to pass a8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in, long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to i500° to 1600°F. and the gas treatments lasted from 3 to 6 hr, The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc, had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F," Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me."

Jan 1, 1940

By H. A. Guess

AT the outset, said Mr. Guess, I may say that although I believe the present engineering courses in the various colleges and universities could be arranged to give the student within the same time limit a broader general education of un- doubted value, still I do not agree with the view held by many that engineers in comparison with those of other occupations-let us say doctors, lawyers, bankers, and so-called business men-seldom arrive at high executive positions. After all, we must remember that engineers are not very numerous as compared with the occupations just mentioned and therefore a lesser number reaching high executive positions stated numerically might be a larger number stated as a percentage. We all know there must be throughout the United States say three doctors to one engineer, but I don't think that even numerically there are as many doctors in high executive positions as engineers, and it is a fortunate thing for the country that doctors as a class are so busily engaged in alleviating sickness and suffering and in the advancement of medical science that they do not aim particularly for high executive positions.

Jan 1, 1926

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35' and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption '1 The Land's End of Two Worlds."

Sep 1, 1907

By Krahmann, Rudolf

THE following is an account of a survey undertaken to test the possibility of outlining a kimberlite pipe by magnetouietric methods. Kimberlite is a basic igneous rock closely related to melilite-basalt or alnoite, which occurs either in the form of volcanic plugs or as dikes intruded into rocks of various types and geological ages up to and includ¬ing the Lower Cretaceous. The famous diamond mines of South Africa are all in kimberlite pipes and these pipes are probably the original source as well of the vast alluvial deposits found in various parts of the country. The pipe chosen for this experiment is one that ' occurs on the farm Goedgevonden No. 20, about sixteen miles north of the village of Klerksdorp and ninety miles southwest of Johannesburg. Some prospecting has been done on this pipe and diamonds were produced from it but not in paying quantities. The magnetometric survey was made in June, 1932, by R. Krahmann and H. Wallisch and the results are shown on the accompanying plan. On the plan are shown also the boundaries of the pipe as exposed at the surface and details in regard to the surrounding foundations. These are taken from a geological survey made at a later date by W. Beetz, of Johannesburg.

Jan 1, 1935

By John Johnston

THIS necessarily brief sketch will attempt to summarize the high lights of perhaps the best meeting so far held by the Iron and Steel Division. All sessions were well attended and the discussion was vigorous and of a high order. The technical sessions opened. on Tuesday morning. "Precipitation Hardening of Copper Steels" was discussed by Cyril S. Smith and Earl W. Palmer, and dealt with steel with a 1 per cent copper content. Discussion brought out that there were no fabricating difficulties, but that the surface might be somewhat checked due to intergranular penetration of copper which could be easily taken care of. Probable advantages of steels of this type for high temperatures were pointed out. "An Improved Nickel-chromium Hardened Chilled Cast Iron," by J. S. Vanick, described a wear-resistant cast iron and evoked a lively discussion.

Jan 1, 1933

By A. Hultgren, G. Phragmén

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

By G. Phragmén, A. Hultgren

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

"Minerals in Transition" is the timely theme of this year's SME-AIME Fall Meeting and Exhibit, to be held September 10-12 at the Salt Palace, Salt Lake City, Utah. Approximately 2000 members and guests are expected to attend the meeting, which will include 117 technical papers, presented during 27 sessions. To complement the technical program, a record number of mining manufacturers and suppliers will be on hand to exhibit the latest in equipment innovation and professional services.

Jan 8, 1975

By W. S. Ayres

A BRIEF history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name Lt breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the "breaker-boy " as a slate-¬picker, with his ever-increasing capriciousness. As the richer veins or ? splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities; particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complication yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Dec 1, 1909

By E. E. White

In August, 1911, I read a paper before the Lake Superior Mining Institute1 on surveying and sampling diamond-drill holes. The present paper gives a more thorough descriptiou of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling' and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drillholes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-hole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a

Jan 1, 1913

By H. H. Stout

In the early fall of 1925, the writer was conducting, in the Ledoux and Co. laboratory, New York, experiments directed toward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various different gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500º to 1600ºF. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode particles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500ºF." Smoot's reaction, after a few moments considera- tion, was, "It looks perfectly all right to me.'' The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after conferring as to ways and means, decided to go ahead with preliminary laboratory experiments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: 1. Since brittle cathodes were often unintentionally produced, it seemed probable that the laws controlling this type of deposition could be ascertained. 2. We had already proved the gas-cleaning feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia University for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrouilded and heated by a resistance coil 01 Nichrome wire. Broken tough cathodes were used. Experimental Procedure The first run took place March 18, 1926. The resistance wire gave out when temperature of 1000ºF. was obtained. Pressure was immediately applied: perceptible ram movement stopped when 39,000 lb. per sq. in. on the copper was reached, with a maxi-

Jan 1, 1941

By H. O. Hofman

(Canal Zone Meeting, November, 19]0.) THE sudden decease, April 1, 1910, in Chicago, of Dr. Franklin R. Carpenter was a shock to his- many friends. He died in his sixty-second year, of heart paralysis. To most fellow-members of the Institute who have followed the progress of the. last twenty-five years in the mining and treatment of non-ferrous ores, the work of Dr. Carpenter in that line is familiar ; but very few, even of those who knew him well in the later years, are acquainted with his earlier struggles to satisfy an inborn hunger for knowledge. The story of his life resembles that of the pioneer who opens up new country; overcoming hardships with indomitable courage, meeting doubts and difficulties with an alert and open mind, and exercising in the face of reverses an unconquerable perseverance. It seems appropriate to place on record in the Transactions a brief outline of the life and work of this eminent engineer. During the past 15 years of his life Dr. Carpenter was much interested in genealogy. In the pursuit of this study as an avocation, he traced his own ancestry to the time when ?Hugh," called "le Charpentier" on account of the dexterity with which he had swung his battle-axe as a crusader, settled in Sussex on lands received from William the Conqueror. The Carpenters came to this country with William Penn. A prominent member of the family was Joshua Carpenter, the founder of Christ Church, Philadelphia. Dr. Carpenter's branch of -the family moved from Pennsylvania into that part of Virginia which is now West Virginia, where his grandfather settled in Harrison county, while the grand-uncle went further west, and built the first iron-furnace at Hanging Rock, Lawrence county, Ohio. In fact, since early times, the Carpenters appear to have been iron-masters. Franklin R.. Carpenter was born, Nov. 5, 1848, in Parkers-

Aug 1, 1910

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS ALABAMA Aldrich, Aldrich, W F Anniston, Noble, A E, Smith, N B Aibacoche, Bradley, D II Bessemer, Fergusson, V Birmingham, Aldrich, T H, Aldrich, T H, Jr, Bowron, J, Bowron, C E, Davis, F H, Dimmick, F D, Hillman, McCarthy, M E , McCormack, McCrery, Ramsay, E, Shook, A M Bridge¬port, Wheeler, S K Ensley, McDonald, S, Shook, J W Fanbanks, Hamil¬ton, A L Helena, Squire, J Huntsville, Moss Lehigh, Toulmin Oxmoor, Green¬amyer, A G Plasma, Gage Rock Run, Garvin Sheffileld, Miller, D I Tuscaloesa, Lodge, J University, McCalley Woodward, Bukofzer, Woodward, A H ALASKA Dawson, Buck Douglas Island, Corbus, J P , Macdonald, J Hames, Le Wald, E A Jualin, Hoggatt, W B Juneau, Denby, Gaifield, Garside, Hamp¬ton, W H Rodman Bay, Phillpots Snettisham, Tisdale Sumdum, Thane Tel¬ler, Hirshberg, M R Treadwell City, Batcheller, J H , Kinzie Valdez, Esterly, G M Yukon, Dawson, Elmer, J M ARIZONA Bisbee, Clark, G C, Coombs, H L , Douglas, W, Hoatson, Parnall, S A, Pelton, R T, Ricketts, L D, Sherman, G F G, Smith, F W, Smith, H A Black Diamond, Bagge Blanchard, Cummins, Murray, J J Casa Grande, Rich¬mond, A B Clifton, Colquhoun, Grabill, Murray, H T , Plater, Smith, J D A, Veitch, Watson, W S Congress, Goodloe Crown King, Alexander, G E Douglas, Cornell, Kraemer, E L, Lee, G B, Rutherford, F Globe, Berray, Hoar, Snell Harrisburg, Smith, F C Jerome, Clark, W A, Thomas, C A Kingman, Treadwell, Wallace, J P Kirkland, Bretherton, G K Kofa, Lamp¬shire, J O , Pomeroy, H G Mayer, Haggott, E A Metca j, Blumenkranz, M , Forbes, D L H Morenca, Clark, C D, Fleming, J B, Honey man, Mills, C E, Wallace, L R Morristown, Stevens, H W Nogales, Glove, H G, Sandoval, A , Sandoval, P Octave, Rose, G W Phoenix, Armstrong, T , Butler, C E, Defty, Lindsay, L Prescott, Blauvelt, H , Bunker, C E, Claypool, W M , Drescher, F M , Fairbank, Nissen Tombstone, Gage, Poindexter, C L , Staunton, Walker, E W Troy, Cutting Tucson, Blake, W P, Burgess, De Lashmutt, I, McCleary, Mann, Prout, J W , Jr ARKANSAS Fayetteville, Purdue Fort Smith, Bache, F , Denman, H Little Rock, Fordyce, Scholz CALIFORNIA Alameda, Arents, King, L Arnador City, Downs, Tregloan Angeles Camp, Dig¬gles, R N , Kenney, C E Antioch, Belshaw Auburn, Coe, I J Ballarat, Thorns Berkeley, Abadie,, Christy, Dozier, Hall, F F , Hersam, Landfield, Lind¬say, L , Mansfield, N T, Morley, W S , Sharwood, W J Bag Oak Flat, Dron Bodae, Hamilton, W R, Hoover, T, Hoover, T J, Jackson, B L , Nutter , E, H Bullion, Power, H T Callahan, Scott, E H Campo Seco, Baird Cartero,

Jan 1, 1910