Search Documents

By H. K. Birnbaum

The termination of a twin lamella in the interior of a crystal requires accommodation of the strains at the tip of the twin which result from coherency of the twin and matrix. In zinc and magnesium crystals,

Jan 1, 1960

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman' reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser' reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,' values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,' on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.' When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By Edward H. Robie

NEVER before have the annual company reports in the mineral industry field exhibited the typo-graphical art so abundantly as does the current crop. Time was when most company reports made a drab appearance and dry reading, mostly confined to financial data and text that gave little information to the public or technical men. Now, the dollar statistics assume less importance. Considerable information is given on what is going on at the company's plants, new equipment being installed, new methods, properties under development, ore reserves and grades, and similar information of interest to professional men working in the field. We have one suggestion for further improvement: The names of the officers and directors of the company are always given, but only a few companies give the names of the principal operating officials. We think, in the case of a mine for example, that the name of the general manager, his assistant, the mine and mill superintendents, and any other top operating officials who have been largely responsible for the success of operations, are worthy of mention. The reports are now widely read and this recognition is due them. Conspicuous among the annual reports that we happen to have seen, in point of typographical attractiveness, are that of the Texas Co., celebrating its fiftieth anniversary with a gold-plated cover and gold printing inside; and that of Noranda Mines Ltd., with a red and black cover that would attract attention anywhere. Comment on economics, taxes, and labor give an excellent picture of what our industry is facing. Consider the following, from the report of the Union Oil Co. of California:

Jan 1, 1952

[A Editor's Note: Annual Reviews of various subjects and areas are found in February issues of Mining and Metallurgy and Mining Engineering. These Annual Reviews are not listed per se in the Index. Abating Stream Pollution in Anthracite Coal Fields. ME Mar 50 Abbadia San Salvatore mine, Italy. T178, 297 Abbott, C.E.: Limestone Mine in the Birmingham District. With Discussion. T129, 62 ABC Typifies Trend to Mechanized Mining and Coal Preparation. ME Dec 50 Abel, J.F.: Statistical Analysis of Tunnel Supporting Loads. T235, 288 Sulzbach, J. F., and Walker, D.K.: Ice Tunneling in Greenland. ME Jun 59 Aberfoyle tin mines, sphalerite, chalcopyrite, stannite, as intergrowths. T214, 1147 Abnormal Behavior of Some Ore Constituents and Their Effect on Blast Furnace Operation, The. T241, 1 Abrams, C.J.: Industry's Responsibility in Postwar Economy. M&M Mar 45 and Haley, D.F.: History of Crushing and Milling at Climax. M&M Jun 46]

Jan 1, 1972

By John N. Dew, William L. Martin, `

This paper describes the results of a laboratory investigation conducted to obtain data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. Air and fuel requirements, rates of advance, com-bustion temperatures, and coke and fluid distributions are presented. The mechanism of oil recovery by in stiu combustion is discussed. Five crude oils ranging in gravity from 10.9 to 34.2"' API were prodrrced from a semiadiabatic, uncon-.solidnted sand pack by in situ combustion. Experimental conditions were varied over a wide range in order to determine the inter-relation-.ships of process variables. The mini-mum air flux requirement for self-sustained combustion was found to he less than 10 scf/hr-ft'l. The rate of advance of a self-sustained combustion zone was found to be nearly proportional to the air flux at the combustion front. The effects of presrure and injected air flux were studied in a series of experiments using a 21.2" API crude. A minimum air require-ment was observed at an air .flux of 20 scf/hr-ft'. The oil saturation con-sumed as fuel averaged 5.5 per cent of pore volume. The effect of air pressure was, found to be .small for experiments having high combustion eficiencies. This study should promote a better understanding of the problems and mechanisms involved in labora-tory investigations and field applications of the in situ combustion pro-cess. The data presented will be use- ful in the interpretation of results of field tests. When tempered with volu-metric sweep efficiencies, the data can be used in making preliminary economic appraisals of the process as applied to reservoirs containing high porosity unconsolidated media. INTRODUCTION The purpose of this work was to obtain laboratory data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. In situ combustion basically consists of (1) injecting air into a reservoir through selected input wells to create an air sweep through the reservoir, (2) igniting the crude at the injection well, and (3) propagating the combustion front through the reservoir by continued air injection. By this means, oil is swept toward producing wells in the area. The fuel for combustion is supplied by heavy residual material (coke) which has been deposited on the sand grains during distillation and cracking of the crude oil ahead of the combustion front. Recovery of petroleum by a combustion or heat wave process is not a new idea. F. A. Howard was granted a patent in 1923 on a process in which air and a combustible gas were pumped into an injection well and ignited.' Russian engineers reported on field experiments with a crude oil gasification process in 1935'. Other known early field tests include those conducted near Bar-tlesville and Ardmore, Okla., in 1942." More recently completed field tests include an inverted seven-spot by Sinclair Oil Co. in the Delaware-Childers field, Nowata County, Okla.'; a three-well and an inverted five-spot test by Magnolia Petroleum Co. in Jefferson County, Okla."."; and a test by California Research Corp. in the Irvine-Furnace field in Kentucky. The Worthington Corp. has completed a test in cooperation with the Forest Oil Corp. in Clark County, 111.l Several field tests are now in progress. Sinclair has acquired a 600-acre lease in the Humboldt-Chanute field, Allen County, Kans., and is under way with a large-scale operation. Three field tests are under way in California. The General Petroleum Corp. is conducting an inverted five-spot pattern test in the South Bel-ridge field in Kern County under a cooperative agreement with 11 other companies, including Continental Oil Co. California Research Corp. is conducting a four-well pattern test in Midway-Sunset field near Maricopa, and Richfield Oil Corp. is under way with a test in the Ojai field in Ventura County. Although the published information is valuable concerning results of field tests, little laboratory data other than that reported by Kuhn and Koch5 are available to aid in appraising the tests from a technical or economic standpoint. Engineering data needed to evaluate the process include the amount of air required per barrel of oil recovered, minimum injection rates which will support combustion, rates of advance, air required per unit volume of reservoir cleaned, amount of oil recovered, and amount of oil consumed as fuel. The present laboratory investigation was undertaken to provide these data for that portion of the reservoir swept by the combustion zone. The first phase of this investigation was exploratory in nature and was conducted at injection pressures less than 100 psig. Data were ob-

By Raymond B. Ladoo

Wollastonite is a calcium metasilicate, with the formula CaSiO3; containing theoretically 48.3 pct CaO and 51.7 pct Si02. It is one of many natural and synthetic silicates with varying CaO/SiO2 ratios, with and without water of crystallization. While it is a very common mineral, deposits of sufficient size and purity to be of commercial interest are unusual. There is only one producer (1958) of wollastonite for industrial use in the United States, Godfrey L. Cabot, Inc. at Willsboro, New York. There has been a small production of surface material for ornamental use from near Blythe, California. Carload tests have been made on California wollastonite for making mineral wool and a commercial plant for this purpose was projected in 1957. Properties Wollastonite is monoclinic and commonly occurs in masses or aggregates of bladed or needle-like crystals. It has a perfect cleavage parallel to the long prismatic axis. It is rather brittle and some types grind easily to a very finely fibrous product, but other types, due to interlacing of fibers, are tough and difficult to grind. Mobs hardness is 4.5 to 5; specific gravity 2.8-2.9; index of refraction 1.616 to 1.631; melting point 1,512°C. Color when pure is a brilliant white, but when less pure it may be gray or brown. Luster is vitreous, transparent to translucent. Common mineral associates are garnet (several varieties), diopside, calcite and quartz. The nature of the mineral impurities determines to a large degree the commercial value of a deposit. At Willsboro, New York, the impurities consist chiefly of iron garnet and iron diopside which are both magnetic and so are easily removable by magnetic separation, yielding a nearly theoretically pure product. Some deposits in California contain calcite and quartz which cannot be removed cheaply, thus limiting market possibilities. Occurrence Wollastonite is a contact metamorphic mineral occurring in most places within or associated with impure limestones. The deposits at Willsboro, New York1,2,3,5 consist of two or more beds dipping 15-50°E and striking NW-SE. The main bed, 30 to 70 ft thick, may be traced on the surface for at least 2 ½ miles. In this belt, the Pre-Cambrian Grenville limestone has been injected and partially replaced by the more liquid portions of an anorthositic magma. Buddington and Whitcomb3 have described the rock as "Mixed gneisses, pyroxenite and garnetiferous gneisses and skarns." Prospecting revealed the wollastonite at ten different places in the belt, overlain in most places by a garnet rock. Diamond drilling has proven several million tons with probable reserves around 15 million tons. Interbedded with the wollastonite are beds of garnet from a few inches to several feet in thickness. In the wollastonite ore itself the chief and almost only associated minerals are garnet (mostly almandite but some andradite and grossularite) with small amounts of green hedenbergite. Inasmuch as the almandite and diopside are magnetic they are easily separated from the wollastonite in high intensity magnetic separators. If grossularite should occur in quantity other means of separation would be needed. Wollastonite has been reported at 35 localities in California12 but only those in the Big Maria and Little Maria Mountains, 16 to 20 miles north of Blythe, Riverside County, are

Jan 1, 1960

By James P. Roe

I. INTRODUCTION. THOSE who deem the subject of this paper an old and super¬seded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 ft. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " Stückofen," the father of the blast-furnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand. We have to look back but a century and a quarter to see the introduction of the puddling process by Henry Cort; a process which, reinforced by the iron-oxide bottoms and fettling of Hall, was not less revolutionary in character, and more revo-

Jul 1, 1905

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper' by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a

By Oliver Bowles

TO keep pace with technical progress is an important function of any industry. All branches of mining may learn important lessons by observing progress made in other branches. The non-metallic mineral industries may learn much from each other as well as from the metal miner and the metallurgist. Recent technical advances which have come to the attention of the Committee on Non-metallic Minerals are presented herewith for consideration and comment. It is planned to present this review for open discussion at the February, 1931, meeting of the Institute. Comments will be welcomed either in the form of written or oral discussion. It is desired that new developments not covered in this paper be brought up at that time. Some notable advances have been made in cement technology. Recognition is now being given to the advantages of closed-circuit grinding of cement raw materials in wet-process plants, with stage removal of the fine materials, It increases mill capacity, reduces the wear of grinding media, and also reduces the power requirement. The method is well known in metallurgical plants, and its acceptance by cement companies is another illustration of the lessons the non-metallic industries may learn from the metal industries. Closed-circuit dry grinding has also proved advantageous for both raw materials and clinker.

Jan 1, 1931

By Gram Curtis

The apparatus described below for the handling of plates upon their delivery from the rolls, embodies features believed to be of interest to those contemplating the building of new plate-mills, and also to such owners of existing mills as may be considering the improvement of their works. The points to which attention is called are the small space required for the finishing-end of the mill, and consequently the very moderate size of the building for the amount of plates handled; the directness and ease of manipulation, and therefore the mall amount of labor required; the distribution of plates; the facilities and time allowed for their cooling. These, together with other features of detail and general arrangement scarcely less important, will become apparent when the descriptions and illustrations herewith given are understood. As these devices deal with the finishing of the plates only, they may be added to any plate-train when the floor-space and the building are large enough to permit their introduction; and it will be obvious that the features of this method, more or less modified, are applicable to any existing mill. Figs. 1 and 2 show a three-high 32-and 19- by 120-inch Lauth mill, with hydraulic lifting-tables, served by four heating-furnaces, with hydraulic cranes for charging and drawing. Upon leaving the rolls, the plate is allowed to rest with its forward edge projecting somewhat beyond the end of the catcher's table. Here it is seized by the automatic tongs, A, suspended from a buggy travelling in the overhead trough, B, and actuated by the hydraulic cylinder, C. These tongs are operated by a boy, who stands several feet from the heated plate, and controls the long light handle, D, shown in the plan, Fig. I. His duty is merely to advance the tongs by means of .the hydrulic cylinder, C, to raise or

Jan 1, 1892

By L. G. Austin

My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rapidly developing knowledge of how stressed, brittle solids fractured, based on the Grifith crack theory. On the other hand, reading in the grinding literature gave me: -Kick's Law, which was clearly not correct in the light of modem fracture theory; -Rittinger's Law, which was also clearly not correct; -Bond's Third Law of Comminution, which was claimed to have something to do with the Grifith crack theory, but where the connection between the two was made by intuitive pseudo-scientific reasoning I could not accept; -the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. Incorrect statements abound in the literature, such as "the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1948) and Broadbent and Callcott (1956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1953) in Ger- many. We confirmed experimentally the validity of the equations for describing batch grinding (1962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type, apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, [(Fig. 1)] (Berenbaum and Brodie, 1959).

Jan 1, 1985

By George K. Burgess, Robert A. Hadfield

1. Introduction.—The methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel CO., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.—Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,l as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made. The characteristics of the ingots are given in Table I. Ingots 1, 2, 3, and 4 were cast large end up and fed by the Hadfield method in the usual manner with charcoal and blast continued until the molten steel has set on the top of the head, say varying from 20 to 40 min. To ingots 1, 2, and 4 was added 0.1 per cent. aluminum, and to the nickel-chrome ingot, No. 3, 0.125 per cent. For sake of comparison, there were also included two ingots, Nos. 8 and 9, cast with the small end up and fed by

Jan 1, 1915

By R. D. Nelson, S. D. Dahlgren

The conditions of temperature, strain rate, and total strain favoring deformation by grain boundary sliding, slip, or deformation with concurrent recrystallization were evaluated for alpha plutonium. Grain boundary sliding and slip were studied by examining structures formed on polished surfaces with 4.5 pct compressive deformation. The conditions required for recrystallization were determined from compressive deformation us time curves. At 110" C and at a strain rate of 10&apos;per min, deformation was almost exclusively by grain boundary sliding whereas slip was the predominant deformation mode at -10°C and lo-&apos; per min. Defarmation at intermediate tenzperatures and strain rates produced structures showing mixtures of grain boundary sliding and slip. Recrystallization occurred concurrently with deformation only after a critical strain was reached. About 14, 6, and 3 pct strain was required at 105", llO°, and lZO°C, respectively, before recrystallization started, irrespective of the strain rate in the range of lo-&apos;1 to 10&apos;4 per nzin. L HE temperature and strain-rate dependency of the modes of plastic deformation were evaluated for high-purity as-cast alpha plutonium. The techniques used to study slip and grain boundary sliding were similar to those employed previously for alpha plutonium by Bronisz and Gorum,&apos; and spriet.&apos; Recrystallization was investigated using the methods reported by Nelson.3 Bronisz and Gorum&apos; found that slip occurred on more than one slip system at room temperature, and suggested that grain boundary sliding also contributed to the deformation. spriet2 found that deformation was predominantly by slip at room temperature, and observed one to three orientations of slip traces in individual grains. In addition, he deformed polished samples at 10O° C, but concluded that the deformation character of alpha plutonium at 100° C and at room temperature were not essentially different. Several investigators reported that twinning was only occasionally observed.1&apos;2&apos;4 Nelson3 recently found in creep tests that high-purity alpha plutonium would recrystallize concurrently with compressive deformation at temperatures between 25" and 115°C. EXPERIMENTAL PROCEDURE Electrorefined plutonium having less than 300 ppm total impurities was received from Los Alamos Scientific Laboratory in the form of +-in. diarn cast rods. Major impurities were americium, <I00 ppm, and tungsten, (60 ppm. Less than 25 ppm each of other impurities were present. The rods were cut into right half-cylinders 0.35 in. long and 0.25 in. in diam, and the flat faces along the cylinder axes were metal-lographically polished. To avoid loss of the metallo-graphic polish by oxidation, the polished samples were deformed in a silicone fluid heat treating medium contained in a chamber evacuated to a pressure of lo-&apos; torr. Deadweight loading was used to compress the samples between 4.5 and 20 pct at strain rates between 10"4 and lo- &apos; min-&apos;. Strain rates were determined by dividing the total deformation by the elapsed time of the test, even though the strain rate was not constant during deformation. Curves of strain vs time for samples deformed with a constant compressive stress3 show that the strain rate changes by less than a factor of four during the testing of a given sample, which is small compared to the three orders of magnitude change in strain rate investigated. Two samples were loaded into an ordinary metallographic mounting mold and impacted by striking the mold piston with one blow of a 2-lb hammer. Deformation temperatures for the two impact samples were 25" and 90°C. The samples, following deformation, were washed in carbon tetrachloride and their polished and deformed surfaces were immediately inspected metallographi-cally. Subsequently, the deformation structures were replicated with acetate replicating tape for later electron microscope examination, and the samples were then repolished and etched to reveal the microstruc-tures of the deformed metal. Second-stage carbon replicas were prepared from decontaminated acetate replicas using the procedure developed by Miller, Bierlein, and astel.&apos; Additional samples, which were 0.35 in. long by 0.25 in. in diam, were used to obtain constant load deformation vs time curves. These samples were deformed 10 to 20 pct with loads of 15 and 20,000 psi at 120°C; 30, 45, and 55,000 psi at 110°C; and 20 and 30,000 psi at 105°C. Samples were polished and etched to determine whether or not recrystallization or twinning had occurred during deformation. RESULTS AND DISCUSSION The experiments showed that alpha plutonium deforms by grain boundary sliding, slip, and deformation with concurrent recrystallization. Deformation by twinning was insignificant. Metallographic examination of polished and deformed surfaces revealed grain boundary sliding and slip. The start of recrystallization was ascertained from constant load deformation vs time curves. Deformed surface structures of samples compressed 4.5 pct under four different conditions of temperature and strain rate, Fig. 1, show how the deformation mode changes from predominantly grain boundary sliding to predominantly slip with increasing strain rate and decreasing temperature. Deformation at 110°C and 10" 4 min-&apos;, Fig. l(a), was predominantly by grain boundary sliding. Only a few slip traces can be seen in Fig. l(a).

Jan 1, 1969

By E. R. Gilbert

Klopp et al. have reported data on tensile and creep properties of are-melted and electron-beam-melted tungsten. We would like to point out some similarities between their creep results and ours on are-melted and powder-metallurgy tungstenand offer some alternate interpretations of the data which lead to different rate-controlling mechanisms. Klopp et al. observed extensive transient creep in the 2250" to 3500°F temperature range where the acthetivation energy is 106,400 ± 3300 cal mole-1. They suggest cross slip as the possible rate-controlling mechanism since "cross slip may occur only by the movement of screw dislocations, and not edge dislocations, thus allowing only partial recovery of the strain hardening and resulting in a continuously decreasing creep rate, characteristic of transient creep.&apos;&apos; Our tests on are-melted tungsten and powder-metallurgy tungsten displayed an extensive transient creep stage in the same temperature range but they also displayed a steady-state creep stage. The stress levels and strain rates of the two investigations, 1.4 to 7 kg mm-2 and 10-7 to 10-4 sec-1 for that of Klopp et al. and 4.5 to 10 kg mm-2 and 10-8 to 10-4 sec-1 for those of Gilbert et al., are overlapping. The activation energy for creep of our powder-metallurgy tungsten is 105,000 cal mole-1. This close agreement with the value found by Klopp et al. suggests that the same mechanism may be common to both types of materials. It may be possible to gain some additional insight into the rate-controlling mechanism by applying the analysis made by conrad22 in terms of the activation volume. The value for the activation volume depends upon the dislocation mechanism and may be used to help differentiate between various dislocation mechanisms. The activation volume for cross slip is 10 to 100 b3. Values determined from our data were 130 to 220 b3 which are in better agreement with the range of 102 to 104 b3 for nonconservative motion of jogs. Values determined from data of Klopp et al. are 240 to 1040 b3. We suggest that the rate-controlling mechanism for creep in this temperature range may be nonconservative motion of jogs assisted by enhanced diffusion along grain boundaries or dislocations. This model requires an activation energy lower than that for self-diffusion as is observed. If this is the controlling mechanism, a higher activation energy which is closer to that for self-diffusion might be expected for tests conducted on specimens with reduced grain boundary area, i.e., larger grain size. In support of this premise we have conducted tests on speci- mens having one to three grains per cross section for which a higher activation energy of 130,000 cal mole-1 was observed. Also, in agreement with results of Klopp et al., a faster creep rate resulted from the increased grain size and probable decreased dislocation density. Further argument against the cross slip mechanism is based on the constant activation energy we obsserved over the range of 5.0 to 10 kg mm-2,21 whereas the activation energy for cross slip displays a significant stress dependence.23 In addition to this, the powe on the stress term for the strain-rate dependence appears too high for cross slip. The values for tungsten fall in the range of 4.5 to 7 (Klopp et al. and Ref. 21) whereas values of approximately 2 are observed in creep by cross slip for hep metals.24 At temperatures from 3300° to 4000°F, Klopp et al. observed an activation energy of 141,000 ± 4000 cal mole-&apos; which is less than that for self-diffusion, 153,000 cal mole-1, 25 and less than that reported for high-temperature creep of powder-metallurgy tungsten by Green:&apos; 160,000 cal mole-1. Klopp et al. suggested that recovery of strain hardening by dislocation climb is the rate-controlling mechanism in this temperature region. Actually an activation energy larger than that for self-diffusion is predicted by this model if the temperature dependence of the elastic modulus27 is taken into consideration. Klopp et al. attributed this lack of correlation to the compositional differences between powder-metallurgy tungsten used by Green and their own arc- and EB-melted tungsten. It is our position that the value of 141,000 ± 4000 cal mole-&apos; represents a transitional value between the higher and lower activation energies and does not represent a discrete mechanism of deformation. If the tests had been extended to higher temperatures the higher value of activation energy would have been observed as has been demonstrated by both our analy sis&apos;&apos; of isothermal test data by GE-NMPO28 and differential temperature tests28 on are-melted tungsten. The activation energies determined (170,000 and 160,000 cal mole-1) were greater than that for self-diffusion and are in better agreement with the value found by Green. The model of dislocation climb is associated with ; activation volume of 1 b3 according to Conrad.22 The activation volume calculated for the creep data of fou independent investigators in the temperature range where the activation energy for creep is near that for self-diffusion (Klopp et al. and Refs. 26, 28, and 30) is 110 to 2800 b3 and is in the range suggested for nonconservative motion of jogs. In the case of tungsten this mechanism may be preferred over that of dislocation climb. Sincere appreciation is expressed to Messrs. J. E. Flinn and F. L. Yaggee for the helpful discussions and suggestions in the preparation of this communication.

Jan 1, 1967

By E. V. Potter, H. C. Lukens

THE volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.2 Both sets of data show a minimum solubility between 500° and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts&apos; data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. There- fore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. APPARATUS AND METHOD The apparatus and method were essentially the same as those described in the previous work,1 as shown in Fig, I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transition points determined under such conditions were less accurate. ABSOLUTE SOLUBILITY Procedure and Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1946

By M. D. Curran

AS applied to coal, the term processing is subject to many interpretations. To some it means preparation of coal for the market by mechanical means such as crushing, sizing, washing, or treating with oil or chemicals to eliminate dust or improve combustion quality. To others it means conversion of the coal to other commodities as in carbonization to produce coke and by- products, or to liquids by application of the hydrogenation process. I prefer to classify the various forms of mechanical treatment under the heading of beneficiation and apply the term processing to those methods of treatment that destroy the coal sub- stance through distillation or hydrogenation.

Jan 1, 1939

By George A. Bell

THE mine and milling plant of Demonstration Gold Mines, Ltd., is near the city limits of Baguio, Mt. Province, P. I. The mine road connects with the main highway to Manila. The nearest railway point is near sea level, approximately 40 miles distant. The Baguio district is very mountainous and has one of the heaviest rainfalls in the world. It is therefore difficult to maintain roads or to impound tailings and mine dumps. All supplies are trucked into the district direct from Manila or the nearest railway point, which means uncertain deliveries and high freight rates. Installation of equipment is difficult and costly. The average elevation at the mine is 4000 ft. and the climatic conditions are ideal except for a three months rainy season. The company generates its own power for mining and milling operations with three 400-hp. Ruston Diesel engines direct connected to 250-kw. General Electric alternating current generators. Labor conditions have been excellent, although at present social security laws are causing some unrest. Labor receives a higher average wage rate in this district than other labor in the Islands. The company also furnishes free living quarters, hospitalization and work- men&apos;s compensation. Taxation has been reasonable up to the present time, but some of the new mining legislation may make it difficult to operate and pay dividends. The future depends largely upon the continuation of $35 gold and the political outcome in the Islands. HISTORY The Demonstration ore body was worked by the Igorots for many years, as evidenced by old stopes and fill encountered in present operations. Attention of Americans was first attracted soon after the Spanish- American war. During the building of the Benguet road to Baguio, the engineers and foreman became interested in the geology of the district.

Jan 1, 1939

By Fred J. Miller

FRED J. MILLER was born in Ohio, in 1857. He had a common and high school education, supplemented by personal study and special instruction. After serving a 4-year apprenticeship and working in various capacities in machine shops, he became a contributor to mechanical journals and finally a member of the editorial staff of The American Machinist, where he remained for twenty years, the last ten years as editor-in-chief of the magazine, and vice-president of the publishing company. On retiring from journalism, he was for nine years general manager of a group of typewriter factories, and was then commissioned Major of Ordnance in the U. S. Army, being stationed during most of his service at Rock Island Arsenal, where he organized the Civilian Service Division of the Arsenal. He is now a member of the Technical Advisory Committee of the War Claims Board at Washington. Major Miller became a member of the American Society of Mechanical Engineers in 1890, and has always taken an active interest in its affairs, having served on a number of important committees, and as a member of Council from 1904 to 1907, inclusive. He was elected President in December, 1919.

Jan 1, 1920