Search Documents

By G. F. Bolling

Single crystals of each metal were deformed at 77°K and heated at constant rates, variously in the range 0.125" to 4o°Kper min from 77" to -390oK, while being monitored in an X-ray diffractometer. Changes in diffraction-peak heights and line breadths were used to ascertain the temperature ranges of recrystalliza-tion. The results were subjected to the analysis of nicholas' in order to obtain the rate-controlling activation energies,Q. In this analysis no recourse to a separate and distinct nucleation stage is required and the results of studying recrystallization proved consistent with the hypothesis of a constant number of nuclei or equivalent hypotheses. The values Pb = 5.5 ± 0.5 keal per mole Zn ~ 7.5 Sn - 5 Bi - 9. 5 correspond for lead, zinc, and tin to activation energies obtained elsewhere for grain boundary migration, and for bismuth and lead to previous studies of re-crystallization by Barrett.6 This correlation allows the conclusions that interference from recovery was minimal and that the observed recrystallization rates in these pure metals are effectively governed by grain boundary migration. Good agreement was not found between the results of this kind of study in zone-refined aluminum and previous work; and supplementary isothermral experiments involving hardness tests and metallography did not resolve the discrepancy. Nevertheless, at least a range,Q = 11.5 ± 2 keal per mole, can be assigned to the activation energy for boundary migration in aluminum. An experimental study of one aspect of the recrystallization process is presented here for four metals of different crystal structure. The metals chosen for study were all zone-refined to reduce impurity effects, but the attendant high purity presented a difficulty. For any reasonably high driving force a "re-crystallization temperature", TR, is in the range of 0.25 T,, where T, is the absolute melting point, and study was therefore restricted to lower temperatures. An X-ray technique under constant heating-rate conditions adequate above 90°K was devised for the study; in consequence, a newer type of analysis following Nicholas1 had to be used to obtain quantitative information about activation energies. The standard methods of studying recrystallization have involved the comparable analyses of Johnson and Mehl2 and Avrami3 which are reviewed by Burke and Turnbull.* The general analysis4 which is applied only to isothermal studies using any of various investigative techniques states:

Jan 1, 1968

By S. L. Hoyt

The writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + b range, first described in 1913. These notes are offered, not at all as the final explanation 'of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520' C. and the other at about 600" C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600" C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + B range and increased in magnitude with the amount of B up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + B field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 1, 1919

By L. S. Richardson, N. J. Grant

Iodide-grade titanium, two oxygen alloys, and two aluminum alloys were studied by means of creep-rupture tests from 1000° to 2000°F. From the test information an evaluation was made of, 1) the relative creep-rupture strengths of the u (hexagonal-close-packed) and 0 (body-centered-cubic) forms of titanium and some of its alloys; 2) the effects of solid-solution strengthening by oxygen and aluminum on the u and 0 structures; and 3) the extent and effect of atmospheric oxygen alloying on rupture life in tests above about 1000°F. THE use of titanium alloys at temperatures above 1000° F has been considered unlikely by most investigators because of low creep strength (based on a requirement for room-temperature ductility, formability, and weldability) and low oxidation resistance. The results of this testing program do not entirely uphold this pessimism in terms of strength and oxidation resistance. The observations described below are based entirely on stress-rupture results, although some creep tests were also carried out on these alloys. Three items of primary importance are covered: 1) Stress-rupture data in the form of the Larson-Miller parameter curves for several titanium alloys at temperatures up to 2000°F; 2) The relative strengths of the hexagonal-close-packed a structure and the body-centered-cubic 0 structure; 3) The effects of solid-solution alloying on the creep-rupture properties of titaniu'm at elevated temperatures. Only two investigatons have reported the creep- rupture properties of titanium at temperatures above 1000° F. Lunsford and rant' tested iodide titanium; their values are also utilized in the paper. EXPERIMENTAL PROCEDURE After a few tests had been made in a conventional creep-rupture test machine, it became clear that some sort of atmospheric protection would be necessary for short-time tests conducted at temperatures above 1600°F, or for times greater than 100 hr at 1200°F or above. Several furnace units and test machines were constructed, the most successful of which is shown in Fig. 1. Certain experimental difficulties peculiar to titanium were encountered; for example, the use of molybdenum holders was dictated because titanium forms low melting-point eutectics with conventional high-temperature alloys containing appreciable amounts of iron, nickel, or cobalt. This same difficulty made the use of chrome l-alumel thermocouples in direct contact with a test specimen impossible, above about 1500" F. The high-temperature high-vacuum furnace shown in Fig. 1 was capable of maintaining a vacuum of better than 10"5 mm of mercury at 2000°F (pressure measured in cold part of system) and 5 X lo-' mm at room temperature. Most of the tests eonducted in vacuum were at temperatures

Jan 1, 1960

By C. R. Hocott

The distribution and movement of fluids in oil reservoirs are influenced to a great extent by capillary forces, which depend upon the size and shape of the pores in the reservoir rock, the surface characteristics of the rock, and the interfacial tension between the fluid phases. This paper presents the results of an investigation of the interfacial tension between salt water and crude oil containing dissolved gas under reservoir conditions. Apparatus and Procedure In the preliminary phases of this investigation, it was found that a scum formed at the oil-water interface, which made measurement of interfacial tension by either the ring or capillary rise methods unreliable. Accordingly, the drop-weight method, in which a fresh interface is continuously formed, was selected. In this method, a tip through which drops of one fluid can be expelled is immersed in a second fluid. At the instant that the drop becomes large enough to fall, the gravitational force tending to pull away the drop exactly balances the interfacial force tending to hold it. From the size of the drop, the dimensions of the tip, and the density of the two fluid phases, the interfacial tension may be calculated. The apparatus consists of a circulating pump for bringing the oil to equilibrium with gas at the desired pressure, a displacement pump for forming the drops, an interfacial tension cell in which the drops are formed, and a density cell to determine the density of the oil. The density of the water is determined separately in another apparatus. A flow diagram of the assembled equipment is shown in Fig. 1. The interfacial tension cell contains a stainless-steel dropping tip suspended from the top and extending below the surface of the oil. The tip is a cylindrical rod with a small hole in the center through which the water was forced to form the drop on the lower face. The walls of the tip were highly polished, to prevent the water on the tip from creeping up the side and increasing the effective diameter. The face of the tip, how-

Jan 1, 1939

By C. R. Hocott

The distribution and movement of fluids in oil reservoirs are influenced to a great extent by capillary forces, which depend upon the size and shape of the pores in the reservoir rock, the surface characteristics of the rock, and the interfacial tension between the fluid phases. This paper presents the results of an investigation of the interfacial tension between salt water and crude oil containing dissolved gas under reservoir conditions. Apparatus and Procedure In the preliminary phases of this investigation, it was found that a scum formed at the oil-water interface, which made measurement of interfacial tension by either the ring or capillary rise methods unreliable. Accordingly, the drop-weight method, in which a fresh interface is continuously formed, was selected. In this method, a tip through which drops of one fluid can be expelled is immersed in a second fluid. At the instant that the drop becomes large enough to fall, the gravitational force tending to pull away the drop exactly balances the interfacial force tending to hold it. From the size of the drop, the dimensions of the tip, and the density of the two fluid phases, the interfacial tension may be calculated. The apparatus consists of a circulating pump for bringing the oil to equilibrium with gas at the desired pressure, a displacement pump for forming the drops, an interfacial tension cell in which the drops are formed, and a density cell to determine the density of the oil. The density of the water is determined separately in another apparatus. A flow diagram of the assembled equipment is shown in Fig. 1. The interfacial tension cell contains a stainless-steel dropping tip suspended from the top and extending below the surface of the oil. The tip is a cylindrical rod with a small hole in the center through which the water was forced to form the drop on the lower face. The walls of the tip were highly polished, to prevent the water on the tip from creeping up the side and increasing the effective diameter. The face of the tip, how-

Jan 1, 1939

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-

By C. M. Haight

The mines of the New Jersey Zinc Co. in New Jersey, are situated in the northern part of Sussex County, at Franklin, formerly Franklin Furnace, and also at Ogdensburg. The mine at Ogdensburg is still in the development stage, but the, mine at Franklin, with which this paper deals chiefly, has been a steady producer of high-grade zinc ores for many years. The town is about 50 miles from New York City, among the foothills -of the Kittatinny Mountains. It is equipped with water supply (filtered and chemically treated), good roads, electric lights, efficient police protection and excellent schools, including a new vocational high school. For a mining community, the conditions and location are far above the average. Franklin Furnace Folio, No. 161 of the U. S. Geological Survey, describes the geology and mineralogy of the district in detail, so that merely an, outline of the main characteristics of the orebody need be given. The

Jan 10, 1917

By Charles Wert

THE diffusion and precipitation of carbon and nitrogen in a iron have previously been investigated using the internal friction as a measuring tool.' Most of this work has been done on rather pure iron; no effect was observed which would indicate that either of these phenomena is affected by the rather small amounts of impurity found in these samples of iron. Fastz observed, however, that both the diffusion rate and the aging properties of nitrogen in iron were sensibly changed by the addition of Vz pet Mn. The diffusion rate at a given temperature is reduced and the nucleation of nitrides is apparently changed somewhat. He observed no such changes for carbon in this alloy. Later Dijkstra and Sladek" extended these observations on nitrogen to other alloys of iron. They found that metals other than manganese also influence the behavior of nitrogen in iron; chromium, molybdenum and especially vanadium affect the diffusion and precipitation of nitrogen even more than manganese does. Their results have been verified in all essential details by this author, who finds in addition that small additions of nickel have about the same effect on the diffusion of nitrogen as the same amount of manganese. The present work was undertaken to study the effect on carbon in iron of these alloying elements. The alloys used had two sources. The material used as a "standard" (designated Fe in this paper) in the measurements was some iron supplied by J. K. Stanley, of Westinghouse Electric Corp., who reported 0.01 pct 0, as the only major impurity. He also made up an alloy of 0.26 pct Ni and one of 0.9 pct Mo using this same iron as a base. They were supplied by him in 2 lb billets, which were sawed into rods and cold formed into 0.030 in. wires for measurement. The alloys of chromium, manganese, and vanadium were prepared by the metallurgy section of the Institute for the Study of Metals, University of Chicago, by adding these metals in turn to vacuum melts of National Research Corp. iron. The small castings prepared in this way were also cold formed into 0.030 in. wires. After these wires had been prepared they were decarburized for 30 min at 730°C in wet Hz. After this treatment, no trace of carbon (as measured by internal friction) could be found. All specimens were then carburized for about 15 min at 710°C and water quenched. By this treatment the internal friction at 40°C was raised to a Q-' ~ 0.015. The diffusion of carbon in these alloys was studied by observing the shape and position of the internal friction peak at 0.9 cycles per sec. These measurements were made using a torsional pendulum in a manner described earlier.' The data are plotted in Fig. 1. It is seen that there is no apparent difference in internal friction between the various alloys. This is in marked distinction to the broadening and shift-

Jan 1, 1953

By J. J. Pye, J. B. Drew

The surface-diffusion coefficients of Ni63 diffusing on low-index planes of nickel single crystals have been measured over the temperature range from 400° to 1000°C using a precision autoradio-gvaphic technique. The activation energy for sur -face diffusion appears to he the same on the {111}, {110), and (100) planes and amounts to -0.60 ev. This is in good agreement with the value (-0.62 ev) reported for (111) planes obtained by mass-transport techniques. In an earlier paper, the authors have reported self surface-diffusion coefficients on silver.' In that work, a deviation of the diffusion coefficients from linearity in the Arrhenius plot was observed at high temperatures. This effect was attributed to a loss of tracer atoms into the bulk by volume diffusion. The purpose of the present work was to extend the technique developed to the nickel surface-diffusion system up to the point where volume diffusion would come into play. The nickel system especially lends itself to this technique due to the high efficiency of the isotope in darkening the film and the large absorption of the weak radiation (0.063 mev /3- particle of the trapped tracer atoms. The diffusion coefficients and ictivation energy for different orientations on nickel can also be compared with a report published by Blakely and Mykura 2 where a mass-transfer technique was used. This paper reports the self surface diffusion of nickel on the low-index planes over a wide temperature range using a precision autoradiographic technique. EXPERIMENTAL PROCEDURE The experiment is similar to that described in the earlier publication consisting of a radioactive needle as a source resting on a flat, smooth, chemically polished surface annealed in a dynamic dry-hydrogen atmosphere. The needle is held snugly on the surface by a holder fabricated from commercially pure nickel. The point source is made by grinding down a small-diameter nickel rod until a tip of approximately 0.1 mm radius is formed. It is then etched and the needle tip plated with the radioactive isotope Ni63. Nickel single crystals were used whose main impurities were spectrographically determined as Co 0.05, Fe 0.007, C 0.005, and S 0.003 pct. The surfaces, oriented to within 1/2 deg of the low-index planes, were carefully mechanically polished and etched in a 50-30-10-10 hot solution of acetic, nitric, sulfuric, and phosphoric acids giving a smooth polished surface. The crystals were then washed in distilled water and alcohol. Annealing temperatures ranged from 400° to 1000°C with a furnace arrangement in which the crystals could be brought up to temperature in times short compared to diffusing times. The temperature was maintained constant to ±10°C. In the temperature range investigated, the ratio of the surface-diffusion coefficient to the volume-diffusion coefficient (Ds/Du) was 105 or more and the mean bulk-penetration values, calculated from literature values of volume-diffusion coefficients,3 were on the order of 10-5 cm. After the diffusion anneal, the sintered needle is removed, and both the radius of the needle point and spot left on the crystal face are measured. The crystal is then placed on photographic film. Diffusion profiles are obtained by scanning the film with a recording microdensitometer which has a slit width of 10µ. DISCUSSION AND RESULTS The experimental conditions are such that the source strength and needle radius are essentially constant and the time is adjusted such that the mean bulk penetration is small. An exactly analogous heat-flow problem has been considered by Carslaw and Jaeger4 and the solution can be written in integral form as:

Jan 1, 1964

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By H. R. Peiffer

The increase in electrical resistivity, ?pT,at 78°K was measured as a function of elongation, E, at 78°K for a 2 pct (approximately) by weight finely divided alumina in silver material. The amount of increase in electrical resistivity (?pT) is a function of the amount of alumina present and can be represented by: ?pT = cen where c and n are constants. The constant c increases and the exponent n decreases with increasing alumina content. Approximately 33 pct of the resistivity increase is recovered upon annealing at room temperature. RECENTLY, dispersed phase alloys' have shown promise for use at elevated temperatures. These materials have a high creep resistance, a high-temperature strength considerably above that of the pure matrix, and a high electrical conductivity. These materials also show other properties such as retardation of re crystallization and resistance to flow even above the melting point of the matrix.' It is believed that high-temperature creep is retarded in these materials because the dispersed phase blocks the motion of dislocations. According to schoeck3 and also Weertman,4 the rate controlling process is the climb of dislocations around the dispersed phase particles. Any mechanical property of these materials, or any other material for that matter, can be explained on the basis of defect structures and their interrelations. It would certainly be interesting to learn something about the effect of a dispersed phase on dislocation densities and also their effect on point defect concentrations following cold work. This is the purpose of the research discussed herein. The method used was the measurement of the electrical resistivity as a function of elongation at low temperatures. This scheme has already been applied to the studies of pure metals.5 Electrical resistivity measurements conducted on pure metals such as copper, silver, gold, and so forth, have indicated that defects such as vacancies and dislocations are formed during deformation.5 It has been shown by van Bueren6 that the resistivity change, ?p, should increase with elongation, E, according to the following relation: Ap=Al/2 + B£3/2 where A and B are constants of the system; ?p is in µ? cm. The first term refers to the amount of resistivity change associated with line defects and the second term with the change associated with point defects. A later calculation yielded exponents of 3/4 and 5/4, respectively.6 Manintveld7 has shown that the resistivity of copper increases with strain according to a 3/2 power law, whereas van Bueren has shown that the resistivity of silver increases according to a 5/4 power law. Assuming then that van Bueren's calculations are correct, it appears that line defects contribute very little to the electrical resistivity. There is some doubt, however, as to the validity of van Bueren's expressions for all cubic metals.' In fact, the data on copper and silver are not conclusive. In this in-

Jan 1, 1962

The Alligator Ridge Project is owned jointly by Amselco Minerals Inc. and Occidental Minerals, with Amselco being the operator. It is the latest of Nevada' s gold heap leaching operations , having gone into operation in October of 1980 after a design and construction period of only seven and one-half months. Alligator Ridge is located about 77 km (48 miles) northwest of Ely, Nevada. Three separate but adjacent ore bodies will be mined: Vantage I, II and III. The first lies virtually at the surface and is totally oxidized; the second is somewhat deeper and contains some carbonaceous material; and the third is at the lowest horizon and contains substantial carbonaceous ore. The ore is a Carlin- type siltstone which has been silicified, especially at depth, and contains finely disseminated free gold. Exploration drilling on Alligator Ridge resulted in the defining of an ore reserve of about 4.54 million mt (5 million st) averaging 4. 12 g Au per mt (0. 12 oz Au per st). A pilot heap leaching program was run during 1979. Because of the high content of fine material in portions of the ore body, one test heap of 5,000 tons was leached, after being crushed to 19 mm (314 in.), in the conventional manner using cyanide and caustic while a second heap of 2,500 tons of ore was agglomerated with cement before leaching. Results of this work were reported at the 1980 American Mining Congress meeting by Paul Chamberlin (see Bibliography). The test work clearly indicated the superior leaching qualities of the agglomerated ore, and the plant was designed on this basis. Run-of-mine ore is crushed in an open-air crushing plant using a jaw crusher followed by two cone crushers, one standard and one shorthead. Provision was made to bypass the shorthead when the ore is wet from rain or snow. Crushed ore at 19 mm (314 in.) size is mixed with cyanide solution and cement, with the ratio of the latter to the ore being 2 to 5 kg per mt (4 to 10 lb per st). The resulting moisture content is about 870, and the fines are effectively bound to the coarse particles so that migration of the fines in the heap does not take place during leaching. For agglomeration, Amselco uses a rotating drum 2. 75 m 0 by 6 m long (9 ft 6 by 20 ft). For the same agglomeration, Candelaria uses three "grasshopper" conveyors, with introduction of caustic- cyanide solution at the conveyor transfer points. Provision was made for future addition of cement slurry at these same points.

Jan 1, 1981

By C. Willard Hayes

Introduction.—The recent developments in the metallurgy of aluminum and its consequent rapidly growing use in the arts are at present attracting considerable attention to its ores. The success of the Hall electrolytic process, by which the metal is obtained directly from the oxide, has removed bauxite from the position of a rather uninteresting mineral to that of an important ore. Its production on a commercial scale is so recent, particularly in this country, that little attention has yet been paid to its mode of occurrence and origin.. Any investigation, therefore, which throws light upon these points should be of interest to mining engineers- at the present time, especially if the conclusions afford a basis for estimating the probable extent and value of deposits already known and a mane of directing search for others. Two localities in the United States have so far yielded bauxite in commercial quantities. These are in Arkansas and in the Coosa valley of Georgia and Alabama. According to descriptions of the Arkansas deposits by Branner, they bear little resemblance to those in the Southern Appalachians and their geological relations appear to be entirely different. Only the latter deposits are considered in the following paper. These have been briefly described by McCalley† and Spencer.† They were visited by the writer during the past summer and somewhat carefully examined, in connection with the study of the areal geology of the region. Location of the Deposits.—The ore is found irregularly distributed within. a narrow belt of country extending from' Adairsville, Ga.,

Jan 1, 1895

By D. Mizer, J. B. Clark

In a recent investigation of the entire magnesium-yttrium phase diagram, Gibson and Carlsonl report the maximum solid solubility of yttrium in magnesium as 8.0 wt pct Y at 1050°F (565°C). However, independent studies of the precipitation in magnesium-yttrium alloys, 2 conducted prior to the publication of the above phase diagram, indicated a greater solid solubility of yttrium in magnesium. Accordingly, the magnesium-rich region of the diagram was re-investigated to determine more accurately the liqui-dus, solidus, and solvus of the magnesium solid solution in this system. Metallography and thermal analysis were chosen as the best corroboratory methods for accurately determining this region of the diagram. A magnesium-yttrium master alloy was prepared from yttrium of 99.9 pct purity and singly sublimed magnesium of 99.9 pct purity. Subsequently, the twelve magnesium-yttrium alloys shown in Fig. 1 were prepared using standard alloying procedures for magnesium. Metallographic samples of the alloys were heat treated under an SO, atmosphere in an electric furnace capable of control within ±3oF of the desired temperature. Alloy samples for the metallographic determination of the solvus, and for the precipitation studies were solution treated at 1000° F for 16 hr. Subsequent aging times for the solvus determination varied from a minimum of 6 hr for the higher temperatures up to 816 hr for lower temperatures. Periods of 30 min at temperature were used to generate liquation for the metallographic placement of the solidus and eutectic horizontal. The liquidus and the eutectic horizontal were determined by thermal analysis. Simple time-temper- ature heating and cooling curves were obtained from 10-g alloy samples heated and cooled in a well-insulated electric furnace. An Iron-Constantan thermocouple was placed in direct contact with the sample. The thermocouple did not contaminate the alloy sample since metallographic examination showed that the alloy melt did not wet or attack the thermocouple. The heating and cooling rates were approximately 5 to 8OF per min. The standard metallographic procedures for magnesium were used in polishing and etching the magnesium-yttrium alloys studied. Glycol etchant* was etchant was used to reveal precipitate in the solvus determination. The redetermined magnesium-rich region of the magnesium-yttrium diagram is shown in Fig. 1. The

Jan 1, 1962

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist-of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' lass because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By C. D. Allman

Specifications for coal at the Grand Lake thermal electric station read in part: "Coal will be Rom Minto Bituminous (strip operation). Maximum lump 3x3x4 ft. Very corrosive, abrasive and when damp, sticky. Coal may consist of frozen lumps of coal, snow and ice." To maintain quality control it was necessary to develop an automatic sampling system capable of: 1) sampling from one 10-ton truckload every 1½ min; 2) permitting an operator to automatically take a sample from each truckload; 3) depositing the sample in a pre-selected container, one of a possible 10; and 4) performing the sampling operations in accordance with latest ASTM specifications for sampling coal with an ash content of 35%. This paper tells how these and other problems were resolved and describes the equipment used. The New Brunswick Electric Power Commission issued detailed specification No. 5351-5009 outlining the scope of work and general requirements for a mechanical coal handling system to be installed at the Commissions Grand Lake Generating Station. The thermal station is located at Newcastle Creek, some 40 miles east of Fredericton, N.B. Canada, on the shore of Grand Lake. This particular location is immediately adjacent to the Minto strip mining coal area of New Brunswick. Contained in the specifications, but not detailed specifically was an automatic coal sampling system. The system outlined, was to be designed and specified by the individual equipment tenderers. In conjunction with the Hardinge Co., the Barber-Greene Co. designed a sampling system which was contained in the general contract proposal. The system as designed originally, however, presented certain limitations to a continuous coal handling system and was ultimately changed. However, it was only through preliminary study and design that problems created by the specifications were determined, and these problems discussed and finally negotiated with the NBEPC engineering staff created the subsequent sampling system now being installed by Barber-Greene. It must be considered that where the original specifications did not detail the mechanical equipment, it was necessary to present a system which would correspond to the intent of specification and for which Barber-Greene would be responsible as to function, but remain in a competitive position with regard to the tender considered primarily on a price basis. The system now being installed, contains basically all the components which were detailed originally, with the exception of the holding bin arrangement, which was changed to allow a continuous operation of the entire coal handling system. SPECIFICATIONS The specifications covering the sampling system follow. 4.5 Sampler: An automatic sampling system shall be installed capable of sampling one-truck load of coal every 1½ min. When the coal is dumped into the receiving hopper, the operator shall push a button and the sampler shall automatically take a sample of that particular coal when it reaches the sampler. Then the sample taken shall be crushed and reduced in quantity to a workable sample and deposited in a pre-selected container, one of a possible ten. All samples and sampling operations shall be in accordance with the latest edition of ASTM designation 492 for sampling coal with an ash content of 35%. The coal for the initial sample shall have maximum sized lumps of about 3/4 in. and the final sample shall be adjustable from 2 to 5 lb per sample and capable of passing through a sieve with 1/8-in. diam openings. It should be noted that, because of the time delay between the time the sample is requested and when it is actually taken, the operator may call for one or two additional samples from different coal before the first sample is completely refined and in the final sample can. Coal is received from a number of different suppliers on the same day, therefore, the system shall be designed so that there is no possibility of mixing or contaminating the coal from the different suppliers. All coal rejected from the sample shall be returned to the main conveyor. All chutes, hoppers, etc. shall be designed in accordance with Section 4.6 of these specifications. 4.6 Chutes, Hoppers, etc. All chutes and hoppers

Jan 1, 1963

By J. A. Finch, S. T. Hall

An oxidative alkaline pressure leach is shown to increase the magnetic susceptibility of coal-pyrite particles. The leach was successfully exploited as a pretreatment in the magnetic desulfurization of an eastern Canadian coal. Greater than 50% total sulfur (65% pyritic sulfur) rejection at 85% clean coal yield was achieved using a high-gradient magnetic separator (HGMS) at 1.3 T and 53 mm/s (2 in. per sec) flow rate, after pretreatment at 0.5 mot NaOH, 85ºC (185ºF), 930 kPa (135 psi) air pressure, 15 minutes retention time, and 20% solids by weight (w/w). Without pretreatment, sulfur rejection at these HGMS settings was less than 5%.

Jan 1, 1985

By J. W. Cunningham, M. J. Stultzman

THE demand for improved materials for high-temperature service has increased during the last few years. Iron,- nickel,- and cobalt-base alloys have been investigated extensively and many alloys with outs'tanding high-temperature strength have been developed. Considerable research has been directed toward improved methods of processing these alloys. The vacuum furnace as a tool for the purification and improved control of high-temperature alloys has been studied extensively and production units are in operation. The research covered by this paper studied the effects of casting in air, vacuum, or argon upon the elevated-temperature properties of two nickel- and two cobalt-base alloys. The alloys investigated were Stellite 31, He 1049, Udimet 500, and Guy Alloy. MELTING AND CASTING PROCEDURES Two heats of each of the four alloys under investigation were melted and investment cast under the following conditions: 1) Stellite 31 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 2) He 1049 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 3) Udimet 500 was melted and investment cast in vacuum with and without additions of zirconium and boron. 4) Guy Alloy was melted and investment cast in vacuum and in argon. The heats were all melted in induction furnaces equipped with preformed magnesia crucibles of 50-lb capacity. The air-melting furnace was powered by a spark-gap converter of 40 kw capacity. The vacuum-melting furnace was powered by a motor-generator set of 100 kw capacity. The argon heat of Guy alloy was melted in the vacuum melting furnace under an argon atmosphere. Virgin materials were used for preparing all heats except the air heats of Stellite 31 and He 1049. The charge for the air heat of Stellite 31 was a commercial blend of shot. The charge for the air heat of He 1049 was Stellite 6 shot plus those virgin materials necessary to give the desired composition. All of the materials used were of the same grade used com-

Jan 1, 1960

By George A. Morrison

THE Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Barberton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITE The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 250 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. GEOLOGY The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft, are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1943

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great, aggregates-preparation plant of the Six Companies, Inc. to supply construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con-tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936