Search Documents

By Sidney Diamond, Charles Wert

The anelastic behavior of Ni-C alloys of nominal 0.5 wt pct C has been determined over a wide temperature range. The most prominent damping effect, that due to the presence of C-C pairs, was measured both above and below the Curie temperature. The effect on diffusion of the C-C pairs by magnetic spin ordering is deduced to be very small. The diffusion coefficient for C-C pairs in nickel is given by the expression ThE solid-state diffusion of both interstitial and sub-stitutional solutes in ferromagnetic solvents has been the subject of a number of investigations. Measurements of the self-diffusion of iron,"' the diffusion of nickel1,4 gold,"1 and cobalt4 into iron, the diffusion of vanadium in an Fe-V alloy,' and the diffusion of cobalt and nickel in Co-Ni alloys9 show an unusual behavior. In both the ferromagnetic and paramagnetic regions, far removed from the Curie temperature, the diffusion coefficient, D, obeys an Arrhenius relation. However, in the ferromagnetic region D is markedly lower than would be expected from an extrapolation of D from the paramagnetic region; this results in an increase in the activation energy in the ferromagnetic region. The cause of this effect for self- and substitutional diffusion is uncertain. Since substitutional diffusion is presumed to proceed by the vacancy mechanism, it has been variously suggested that the increase in activation energy below the Curie temperature is due to one of the following causes: 1) an increase in the energy of formation of a vacancy because of local demagnetization around the vacancy,2,3 2) a decrease in vacancy mobility in the ferromagnetic state,' or 3) an effect on the entropy of motion of a vacancy in the ferromagnetic state.5 Quite another explanation for the observed effect has been proposed by Borg.7 The diffusion coefficient is a function of the elastic constants of a metal. Since the temperature dependence of the elastic constants often changes at the Curie temperature, the temperature dependence of D might be expected to undergo a universal change in the vicinity of the Curie temperature. The magnitude of the change in D would, of course, depend on the magnitude of the change in the elastic constants. One might attempt to differentiate between vacancy effects and elastic effects by making measurements on interstitial alloys, in which vacancy effects play no role. Some measurements of this type have been made; this paper reports additional observations. Measurements of the diffusion of carbon in a Fe by a tracer technique8 and of the diffusion of carbon in a Co and in Co-Fe alloys by a decarburization method9 reveal a small effect, if any, on D of the magnetic change at the Curie temperature. If the effect of spin ordering is only to alter the parameters controlling formation or mobility of a vacancy, interstitial diffusion should indeed remain unchanged through the magnetic transition, as these measurements imply.

Jan 1, 1968

By F. S. McNicholas, R. L. Healy

NOTEWORTHY because of the amount of explosives used, the tonnage broken, and the wide range involved both vertically and laterally, was a large underground blast fired last November at the Hidden Creek mine, Anyox, B. C. Stoping methods and mining prac¬tices at the Hidden Creek mine have previously been described in the technical press. Earlier mining methods employed included shrinkage stoping, glory-holing, and "spiral" stoping. The latter especially has been a practice peculiar to the Granby company, having been used for years at its Phoenix mines and later at the Anyox property where conditions as to size of orebodies and strength of ground both in the ore and walls were similar. These methods all leave tremendous excavations supported at key points by pillars and braces that may only be safely mined by big blasts.

Jan 1, 1935

By R. M. Rose, K. A. Jones

Resistive measurements ulere made on superconducting niobium single crystals in transverse magnetic fields. Crystals were grouln in both high and ulfrahigh vacua, doped with stnall quantities of oxygen, and annealed in ultrahigh vacua at temperatures from 900' to 1350°C. Maxima in the fluxoid pinr~ir~g force were observedfor the [100] and [210] directions. The increase of the critical current density with dissoved oxygen was seen to saturate at relatively low concentration. This behavior, and the variation of J, and residual resistivity (as a function of oxygen content and annealing) of both clean and dirty gassy) crystals, is seen as a consequence of the formation of clusters with (210)~b habit planes and (200)ffo common boundaries. These suboxide clusters are apparenlly stable at high temperatures and very low oxygen concentrations. It is generally known that dissolved oxygen at concentrations well below the solubility limit sharply increases the critical current density of superconducting niobium.' Such a result would not be expected if Nb-0 solutions were random, not even as the result of segregation on the scale usually encountered in solid solutions. According to the Kim-Anderson theory of flux creep,' the critical transport current density is determined by the pinning force Fp associated with some feature of the microstructure. As the Lorentz force. a or (J X R), of the transport current in the magnetic field approaches Fp, flux creep and then flux flow occur. The pinning force is expected to be quite small if the heterogeneity involved is significantly smaller than tte range of coherency which for niobium is circa 250~.~ Although the strain field of an individual oxygen atom in the niobium lattice is relatively large, it does not seem plausible that individual atoms could be so effective as to account for the data. Also, ~ramer~ found that straining and strain aging specimens containing small amounts of oxygen on occasion decreased the residual resistivity. A possible explanation for the above behavior may be found in the work of van Ooijen and van der Goot,= who found that annealing changed J, for niobium foils containing oxygen, and they attributed the changes to ordering of the oxygen atoms. This phenomenon has been observed by other investigators using X-ray and PROCEDURE Cylindrical 4-in.-diam niobium single crystals with axial orientations [ill], [110], [112], and [oo~] were grown from pure niobium, see Table I for analysis, in an ion-pumped ultrahigh-vacuum system using the electron beam floating zone technique. Total pressure during growth was lo-'9 torr: the oxygen partial pressure was less than lo-" torr, as determined by a mass spectrometer. These crystals will be referred to as the "clean" crystals. Similar crystals were also grown in another system at a pressure of 5 X 10"6 torr. These crystals will be referred to as the "dirty" crystals. Specimens 14 in. long were cut from the as-grown crystals and one end was polished down to no. 600 carbide paper smoothness. A back-reflection Laue photograph was then taken in order to fix the crystallo-graphic directions transverse to the crystal. The critical current density J,, the current density necessary to produce a voltage drop of 1.0 pv between voltage leads placed a in. apart, was determined as a function of the magnitude and direction of the transverse magnetic field and of the oxygen concentration. The technique and experimental arrangement was essentially similar to that of Tedmon et al.' In the remainder of this paper, the azjmuthal angle $ for the field H is referenced to the [ I101 direction in all four crystals, and oxygen was added in small equal increments by anodization and annealing.7 The resistivity ratio, RR, of the resistance at room ternperature to that at 4.2"K (H =7.00 kG) was determined as well.

Jan 1, 1970

By R. B. Hoy, Stanley J. LeFond, K. Reckling

World production of natural diamonds prob¬ably exceeds 50,000,000 carats a year. The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, and the Republic of South Africa third. Diamonds are also mined in South-West Africa, Angola, Ghana, Sierra Leone, and other African coun¬tries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today in India, which was the first source of commercial production. In the U.S., efforts at commercial diamond mining have been con¬fined to a small area near Murfreesboro, Ark. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2000 years ago, only about 130 tons have been mined. In order to obtain 1 g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential ma¬terials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic indus¬trial diamonds are now of a quality that per¬mits wide substitution in the fine-grained sizes. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to "modify" light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem dia¬mond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today. About 1475, a Flemish cutter named Van Gerquem discovered that diamond dust on an iron wheel would polish facets on a diamond to provide more brilliance and fire. Cutters continued to experiment with facets, and shortly before 1700 a Venetian cutter named Peruzzi developed the 58-facet brilliant cut. With the development of the science of optics, cutters have learned more about the behavior of light within the diamond. Early in the 20th century, they learned how to angle Peruzzi's

Jan 1, 1975

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By Albert Sauveur

IT WAS in June, 1889, that I was first admitted to the society of educated men. The admission ticket had been signed, on the recommendation of my old and beloved teacher, Bobby Richards, by General Francis A. Walker at the time President of the Massachusetts Institute of Technology, an institution familiarly known as M. I. T. I immediately proceeded to take advantage of that privilege by departing for Steelton, Pennsylvania, where I understood I was eagerly awaited by the educated officials of the Pennsylvania Steel Company. I was some. what disappointed at the casualness of my reception and at being tucked away in that preserve closet of steel works known as the chemical laboratory. At Steelton I met Major Bent who was president of the company. When I say "met," that is a figure of speech as my acquaintance with him was confined to my being shown

Jan 1, 1937

By W. M. Weigel

SALT production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open 'kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been estimated only by geophysical methods. The diameter of the salt core varies from less than ½ mile to over 2 miles. Only domes where the salt is compara-tively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use.

Jan 1, 1935

Total U.S. mineral production reached an estimated $17.8 billion for 1960, 4 pct above 1959 and second only to the record high of $18.1 billion established in 1957. As a group, metals achieved a rise from $1.6 billion in 1959 to $2.0 billion this year, an increase of 28 pct. Similarly the value of nonmetallic production including fuels (i.e., natural gas, petroleum, natural-gas liquids, asphalt and related bitumens, carbon dioxide. anthracite. bituminous and lignite coal, peat, and helium) rose from $15.5 billion in 1959 to approximately $15.8 billion in 1960. However, this 2 pct increase in the total value of non-metallic production was due to an increase in the value of the fuels ($11.8 billion in 1959 to $12.2 billion in 1960) which offset a drop in value of the other nonmetallic minerals ($3.7 billion in 1959 to $3.6 billion in 1960).

Jan 2, 1961

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930

By W. F. Wheeler

A discussion of the paper of W. F. Wheeler, presented at the Toronto Meeting, July, 1907 (Trans., xxxviii., 621 to 632). A. BEMENT, Chicago, Ill. (communication to the Secretary*):¬Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible,", not-withstanding that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combustion-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term ." combustible" was an advance to be credited to the engineer .rather than to the chemist, because the latter, not having to do with the interpretation of analysis in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression " pure coal," which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Sep 1, 1908

By N. A. Gokcen

THE data of Chaudron,1 Tonosaki,2 and Collins³ on the thermodynamic properties of MOO, disagree widely. These authors, by using essentially similar methods, studied the following reaction: 1/2MoO2(s) + H2(g) == i/2Mo(s) + Ph,o H2O(g),K = —----- [1] Ph2 Tonosaki used a vacuum system consisting of a furnace containing MOO, and a water saturator whose temperature was kept at 25 °C with a thermostat. After repeated evacuation, hydrogen was admitted slowly into the system. The experiments were based upon the fact that at a constant furnace temperature and constant partial pressure of water, the total pressure of gas mixture over MOO? + Mo is constant. Any attempt to vary the pressure by external forces would vary only the amounts of MoO2, and Mo, after which the pressure should return to the equilibrium value in accordance with the equilibrium constant of reaction 1. The actual value of K was determined from the total equilibrium pressure (sum of Ph2o + Ph2) at each temperature. The total pressure of gas was varied within the range of 80.2 to 125.4 mm Hg, within a temperature range of 645" to 823 °C. The results were summarized as log K = 0.9413 — 1444.6/T for reaction 1. The ratio of H2O/H2 was considered to be uniform in spite of the presence of a thermal gradient across the static gas phase. It was shown by Rosenqvist and Cox,' however, that in somewhat similar circumstances the error resulting from thermal diffusion may be large. Collins³ improved Tonosaki's method by attempting to avoid thermal diffusion errors. His equilibrium data were obtained at 700°, 800°, and 900° C, and the result for reaction 1 was expressed as log K = 1.258 — 1822/T. The purpose of this investigation was to study reaction 1, avoiding the thermal diffusion errors, and to obtain equilibrium data in a considerably wide temperature range for the reliable extrapolation of the resulting thermodynamic functions. Experimental Procedure The diagram of the apparatus is shown in Fig. 1. Tank hydrogen was passed through a tube containing platinized asbestos at 425 °C in order to convert a trace of oxygen into water vapor. The flow rate was carefully controlled with a capillary-type flow-meter B and a bubbling column D. The gas was then presaturated sufficiently at P and led into a condenser system immersed in a thermostat, controlled to within ±0.002C. The temperature of the thermostat was measured with a thermometer calibrated against a certified standard. The temperature of P was adjusted to avoid the condensation of unduly large amounts of water as judged from the rate of flow out of the capillary tube M. Argon was purified by passing it through magnesium chips kept at 630°C. After passing through the flowmeter B', it was mixed with moist hydrogen emerging from the thermostat. The resulting gas mixture was then led into the hot zone of the furnace through the heated glass tubing and the silica tube S, thus insuring the same ratio of PII2o/Ph2 from the condenser to the reaction chamber, thus avoiding thermal diffusion. The entire gas system was of all-glass construction, except at the magnesium train. The furnace comprised a glazed alumina tube over which a 15-in. platinum coil was wound. The lower end of the alumina tube was tightly closed with a brass bottom and a silicone rubber gasket, and the upper end with two glass disks, each with a hole of 1/16 in. in diameter, through which the gas mixture escaped into the atmosphere. A back-up coil of kanthal wire facilitated the temperature control of the furnace. A coil of annealed molybdenum strip of 99.99 pct purity, 0.005 in. thick and 0.050 in. wide, and weighing 17 g was hung in the furnace with a 0.010-in. platinum wire attached to one end of a sensitive analytical balance. The temperature of the furnace was measured with a Pt-Pt-10 pct Rh thermocouple checked against a standard. The experimental procedure consisted of heating the gas purification trains, adjusting the gas flow rates, attaining a constant thermostatic temperature, flushing the entire system for 2 hr while heating the furnace to well above the expected equilibrium temperature and then cooling it at a rate of 0.3°C per min during which time the change in the weight of molybdenum was observed on the balance. For a given thermostatic temperature, i.e., a constant Prr,o/Px,, molybdenum oxidized upon cooling slightly below the equilibrium temperature. The procedure was then repeated by heating the furnace and thus reaching a temperature slightly above the equilibrium value. The average of the two temperatures, differing by 2" to 3"C, was considered to be the true equilibrium temperature. In order to determine the stoichiometric composition of the oxide phase present in this investigation,

Jan 1, 1954

By W. L. Fink, L. A. Willey

DURING the war there was introduced a new higher strength aircraft alloy designated 75S.1,2.3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75S alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75S alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. PROCEDURE Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75S "as rolled" sheet (0.064 in. thick). The composition° was as follows: Weight Percentage Cu Mn Mg Zn Cr Al with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16 in. i.d. by ¼ -in. o.d. by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064 in. thickness over the junction and adjacent lead wires for a distance of 1 ½ in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3 in. by 9 in. by 0.064 in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75S extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of ¾ in., 2 in., 3 in. and 4 in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 ½ in. Thermocouples were peened into the bottoms of 1/8 in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1947

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1964

By Paul T. Allsman, E. W. Newman

Trenching, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively. Introduction The Montana chromite deposits were the first to be explored under the Strategic Minerals Act of 1939. In June of that year, the Bureau of Mines started exploration by trenching, test pitting, sampling and diamond drilling, and completed the project in March 1943. The U. S. Geological Survey cooperated by mapping the geology and logging the cores. The project was to determine the extent and grade of the chromite ore and to indicate sufficient reserves to justify development and exploitation of the deposits for the national emergency. Exploration has indicated that the district contains the largest and most important reserve of chromite ore in the United States. The Benbow and Mouat-Sampson mines have been developed and a 500-ton concentrating mill has been constructed on the Benhow property and a 2000-ton mill on the Mouat-Sampson property. Concentrates were produced from the Benbow mill three months after the attack on Pearl Harbor, when the nation's major chromite supplies from foreign sources were cut off. History It has been known for 50 to 60 years that some chromite deposits existed in an east-west belt along the north escarpment of the Beartooth Mountains about 25 miles north of Yellowstone Park, but nothing was known of their size and extent until the war demand of 1917 and 1918 stimulated the search. In those years two properties in the Stillwater region were actively developed, but no shipments were made. The Benbow property was located in 1918 by a local group. The property comprised seven claims along the strike at the east end of the belt. An adit was driven several hundred feet on the Eclipse claim. The seven claims were sold to the Chromium Products Corporation of Livingston, Mont., and were subsequently patented. In 1929, an eastern group obtained an option, installed some equipment, and erected several log cabins. The "crash" in the market in 1929 caused the operators to drop their lease, and the property remained inactive until 1939, when the Bureau of Mines began its exploration. Fourteen claims were located on the Boulder River in 1918 and subsequently patented by the U. S. Chrome Corporation.

Jan 1, 1949

By Paul T. Allsman, E. W. Newman

Trenching, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively. Introduction The Montana chromite deposits were the first to be explored under the Strategic Minerals Act of 1939. In June of that year, the Bureau of Mines started exploration by trenching, test pitting, sampling and diamond drilling, and completed the project in March 1943. The U. S. Geological Survey cooperated by mapping the geology and logging the cores. The project was to determine the extent and grade of the chromite ore and to indicate sufficient reserves to justify development and exploitation of the deposits for the national emergency. Exploration has indicated that the district contains the largest and most important reserve of chromite ore in the United States. The Benbow and Mouat-Sampson mines have been developed and a 500-ton concentrating mill has been constructed on the Benhow property and a 2000-ton mill on the Mouat-Sampson property. Concentrates were produced from the Benbow mill three months after the attack on Pearl Harbor, when the nation's major chromite supplies from foreign sources were cut off. History It has been known for 50 to 60 years that some chromite deposits existed in an east-west belt along the north escarpment of the Beartooth Mountains about 25 miles north of Yellowstone Park, but nothing was known of their size and extent until the war demand of 1917 and 1918 stimulated the search. In those years two properties in the Stillwater region were actively developed, but no shipments were made. The Benbow property was located in 1918 by a local group. The property comprised seven claims along the strike at the east end of the belt. An adit was driven several hundred feet on the Eclipse claim. The seven claims were sold to the Chromium Products Corporation of Livingston, Mont., and were subsequently patented. In 1929, an eastern group obtained an option, installed some equipment, and erected several log cabins. The "crash" in the market in 1929 caused the operators to drop their lease, and the property remained inactive until 1939, when the Bureau of Mines began its exploration. Fourteen claims were located on the Boulder River in 1918 and subsequently patented by the U. S. Chrome Corporation.

Jan 1, 1949

By Leonard Logan

Production control in the petroleum industry may be discussed under three general heads: engineering, legal, and economic. Though the problems that fall under the respective heads of engineering, law, and economics are separate, they are dependent and interrelated. The present study will deal with the economic phases of production control and only incidentally with the legal phases as they affect the economics of the problem. No one of these forms of control is more important than the others. The engineers have performed their service well, and although there are many problems of engineering control yet to be solved, they are not pressing. Legal control is a problem for the legislatures and the courts to solve. The petroleum industry is such a comparatively young industry and the legal problems are of such recent origin that the courts have not yet been called on to settle all the issues and the legislatures still have before them bills concerned with the regulation of the industry. Economic control of production in the petroleum industry is a highly desirable goal but it has not yet been completely achieved. Since the first commercial well was drilled in 1859, there have been recurring periods of overproduction. (Over- production will be used here to describe a condition wherein so much crude oil is available that a satisfactory and reasonable price is not received for the product.) The production of oil in 1859 approximated only 2000 barrels. In the following year production jumped to 500,000 barrels, thus bringing into

Jan 1, 1932

By R. T. Walker

GROUND waters-hot or cold-containing small amounts of the more common earth acids, such as carbonic acid, silicic acid, hydrogen sulfide, sulfurous acid and sulfuric acid, have only a very limited "solvent effect on dominantly siliceous rocks, whether of igneous or sedimentary origin, but in limestone they often form extensive cavities; and such "limestone caves" are the only openings of considerable size and continuity in rock formations that do not owe their existence directly and almost wholly to dynamic action. Limestone caves such as are developing at the present time must have been formed in all past geological ages in which limestone beds existed and where suitable conditions for the development of such caves prevailed; hence it would seem a reasonable expectation that, in the course of geological history, a certain number of ancient limestone caves must have been utilized as channels for the passage of mineralizing solutions, during portions of their course, at least, and that, in consequence, orebodies must have been deposited in such caves. Such a conception is not novel; it was proposed many years ago, but its possibilities, as explaining certain types of ore deposits, have been rather lost sight of in the development of the theory of the metasomatic replacement of rocks by minerals. It is the purpose of this article to assemble evidence to show that many of the orebodies found in limestone beds have been deposited in pre-existing caves; to discuss the criteria whereby such orebodies can be distinguished from others which have been formed along fissures and fracture zones traversing limestone, by the more common method of metasomatic replacement, analogous to orebodies in other formations; and to describe certain orebodies-particularly the "ore channels" of the Tintic district, Utah-as illustrative of the principles discussed. Limestone caves may be divided into two classes: those formed by cold, descending surface waters, which emerge again at some lower elevation as cold springs; and those formed by hot, ascending waters of deep origin or circulation, which attain the surface as thermal springs. Although these two classes are similar in many respects, there are certain characteristic and inherent differences whereby they can usually be distinguished.

Jan 1, 1928

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By H. A. Meyerhoff, R. J. Colony

Deposits of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residual limonite at the west end of the island near Mayagüezl-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7"9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugües, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935