Search Documents

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By R. D. Springer, R. L. Wilcox, P. A. PALMARTAN, R. K. Waring, E. A. Anderson

A knowledge of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunately the results vary widely, particularly at higher temperatures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason determinations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zine-rich phases in the solid state,l,2 and methods in which the samples are taken while the bath is liquid and at the desired temperature.3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investigations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility. The low-temperature section of the zinc-lead equilibrium diagram is given by Peirce and Anderson.7 The diagram is based on the data of Hodge and Heyer,8 Arnemann,9 and Peirce.10

Jan 1, 1934

By John V. Beall

On January 1, 1948, we boarded the cage at 7 a.m. and were dropped to the 900 level of the Brunswick shaft. The previous evening, we had attended the New Year's party at the Miners' Guild Hall and as this soireée had not disbanded until the small hours of the morning, we had only had about two to three hours sleep. At the 900 level station, we fell in beside our mining partner, a Cousin Jack, who was known by all as Porky. Porky didn't say anything as we plodded down the drift, we didn't say anything either-in fact there was little conversation by anybody.

Jan 1, 1971

By L. L. Hirsch, W. M. Parris, P. D. Frost

IT has been established that titanium alloys con- taining sufficient amounts of ß-stabilizing elements, such as iron, chromium, or manganese, can be age hardened.' Adenstedt, Pequignot, and Raymer2 showed that age hardening occurred in a Ti-15 pct V alloy at room temperature after it was quenched from a temperature in the ß-phase region. During a recent investigation of the heat-treating characteristics of binary Ti-Mn and Ti-Cr alloys at Battelle, further evidence of low temperature aging was found. Appreciable hardening occurred in some of these alloys at aging temperatures as low as 212 OF (100oC). Indeed, the brief heating period employed for mounting metallographic specimens in bakelite resulted in hardening. It was felt that further information on this low temperature aging phenomenon would be of general interest in view of the large amount of work currently being done on titanium alloys. The alloys examined in this investigation were arc-melted in a water-cooled copper crucible as 3/4-lb ingots. Du Pont Process A sponge was used as a base material. The arc-melted ingots were forged at 1700" to 1800°F (927" to 982°C) and hot rolled at 1450°F (788°C) to 14 gage (0.064 in.) sheet. Small specimens were heated in argon at 1742°F (950°C) for 30 min and quenched in various liquid media or air cooled. They were then mounted in a room-temperature-setting resin and given a metallographic

Jan 1, 1954

By H. B. Aaron

DIFFRACTION micrography provides a useful tool for studying complex strain fields. Newkirk1 observed an X-ray diffraction effect due to strain interactions at the intersection of slip lines in LiF and attributed this effect to a reduction of primary extinction due to strain-gradients. It is the object of the current study to correlate the observations and rationalize the appearance of the strain fields around intersecting slip planes in x-ray extinction contrast studies by a semiempirical method. Fig. 1 shows typical strain patterns observed by Newkirk on (200) reflections in LiF using chromium radiation and a variation of the Berg-Barrett (B-B) technique. In other reflections (e.g., {220}) the strain patterns are absent. If one defines a vector 3 along the striations from the more to the less dense portion, and a vector v in the direction of the X-ray beam parallel to the reflecting plane, such that both 3 and v lie in the reflecting plane of the crystal, Fig. 1, then the positions of the striations on (200) reflections appear to be confined such that where is the angle between v and 3, Fig. 1. It will be seen later that 3 is the projection of Sb on the reflecting planes. In some instances the strain effects are observed only above the slip plane, Fig. l(C), in others only below, Fig. l(D). Where the strains appear to be both above and below the slip line, Fig. l(E), one sees that there are actually two slip lines present, Fig. 1(F) and (G). Furthermore, the strain patterns are observed in the vicinity of the intersection of emergent edge dislocations (diagonal lines on the micrograph) with emergent screw dislocations (horizontal lines on the micrograph), e.g., Fig. l(HJ) and (MN), but not in the vicinity of the intersection of two emergent edge dislocation arrays, Fig. l(HJ) and (KL). However, in the latter case the contrast of the dislocation array itself is reduced along (KL) and increased along (HJ). Line (AB) in Fig. 1 is the edge of the crystal, and the material to the left of (AB) is the side of the sample. Any empirical correlation will have to include most, if not all of the aforementioned observations. Lang2 and Newkirk1 determined that the condition for contrast is given by g-b#0 [2] where b is the Burgers' vector and g the diffraction vector (normal to the reflecting planes). If one assumes that the direction of the observed strain fields is given by the vector sum of the slip vectors (Sb1) of the intersecting slip planes, then Eq. [2] may be generalized to g-S#0 [3]

Jan 1, 1963

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By AIME AIME

THE Wednesday morning session was devoted entirely to the consideration of the tentative code for coal mine ventilation. A. W. Hesse is chairman of this subcommittee. E. A. Holbrook presided at the session and assisted by A. W. Hesse and George S. Rice, gave the historical background of the movement for a ventilation code. They stressed the point that this was to be an engineer's code, and that it was hoped that it might serve as a valuable guide to operating companies in securing greater efficiency as well as safety in ventilation. The discussion was continued into the afternoon session, and by adjournment the entire' code had been covered.' Many sections were referred back to the Committee for further study and several new sections were suggested. The various opinions and new ideas brought out during the discussion proved very valuable and. contributed much to the progress being made in the preparation of this code.

Jan 1, 1929

A discussion of the paper by Mr. Campbell, which was read by title at the Lake Superior meeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 772). These papers are here published onder a mutual agreement between the Councils of the two Institutes, and will also be found in the Journal of the Iron and Steel Institute for the year 1901, vol. ii. Mr. William R. Webster, Philadelphia, Pa., said: We are under great obligation to Mr. Campbell for his exhaustive investigation, and the results he has put before us to-day. They are the most conlplete series of tests that have ever been made, where all the conditions of rolling, etc., were kept uniform. In discussing Mr. Campbell's first investigations, I claimed first, that the method of least squares, then used, would of necessity only gire the average value of any element, and that if the effect of any element was greater in the presence of high carbon than with low carbon this would not be shown by the method of least squares. Secondly, that the effect of manga nese should be considered on acid steel as well as on basic steel, instead of ignoring all the eff'ect of that element when it was below 0.60 per cent., as was then recommended by Mr. Campbell. I am pleased to note that the results of his present investigation confirm my views on these points. In presenting the results of his first investigation, Mr. Campbell referred to my investigation of 1893-94, and took exception to the value of phosphorus varying (depending on the amount of carbon present) from 800 to 1,500 lb. for each 0.01 per cent. He claimed that one might just as well consider the effect of phosphorus as being constant, and of carbon varying. I refer to this, as he now has introduced very similar conditions in his present tables, in that he gives variable values for manganese (depending on the amount of carbon present) for both acid and basic' steels. Can we now say, with more certainty than formerly, which element should be considered as haviup a constant effect ? There is one other point that I took up in my former discus-

Jan 1, 1905

Under date of Sept. 30, the following open letter was addressed to the Members of the Colorado Section of the American Institute of Min-ing and Metallurgical Engineers by a Colorado Committee: At a meeting of the Colorado Section of the American Institute of Mining and Metallurgical Engineers, held on Friday, Sept. 19, a reso-lution was unanimously passed condemning the Engineers' Licensing Bill passed at the last session of the State Legislature, and requesting the Chairman to appoint a Committee to act in conjunction with the other National Engineering Societies and the Colorado Metal Mining Associa-tion, with a view to securing its repeal at the extra session of the Legis-lature which the Governor has expressed his intention of calling. It may be within your knowledge that the bill in question was passed by the Legislature and signed by the Governor without the knowledge of any of the National Societies, and of few if any of their members. Under its provisions residents of other states cannot even come into this to examine a mine without securing a license, and aliens (among whom are many honored members of, the profession in Colorado) cannot obtain such a license at all. The mining industry in this state needs the coopera-tion of outside engineers, and we should welcome any assistance from them that will tend to develop our resources. To attempt to discourage the activity of visiting engineers will inevitably react on us, and brand the state as being hostile to brains and capital from outside. The difficulty of securing a license will prove a serious handicap to young engineers starting out in the independent practice of their profession. Moreover, a license issued to au engineer qualified in one branch will entitle him to practice in any other: so that the license is apt to mislead the public.

Jan 11, 1919

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable-shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 2, 1914

By Herbert Clark Hoover, Lou Henry Hoover

GEORGIUS AGRICOLA was not only the author of works on Mining and allied subjects, usually asso ciated with his name, but he also interested himself to some extent in political and religious subjects. For convenience in discussion we may, therefore, divide his writings on the broad lines of (1) works on mining, geology, mineralogy, and allied subjects; (2) works on other subjects, medical, religious, critical, political, and historical. In respect especially to the first division, and partially with regard to the others, we find three principal cases : (a) Works which can be authenticated in European libraries today ; (b) references to editions of these in bibliographies, catalogues, etc., which we have been unable to authenticate ; and (c) references to works either unpublished or lost. The following are the short titles of all of the published works which we have been able to find on the subjects allied to mining, arranged according to their present importance :-De Re Metallica, first edition, 1556; De Natura Fossilium, first edition, 15,46 ; De Ortu et Causis Subterraneorum, first edition, 1546; Bermannus, first edition, 1530 ; Rerum Metallicarum Interpretatio, first edition, 1546; De Mensuris et Ponderibus, first edition, 1533; De Precio Metallorum et Monetis, first edition, 1550 ; De Veteribus et Novis Metallis, first edition, 1546; De Natura eorum quae Effluunt ex Terra, first edition, 1546 ; De Animantibus Subterraneis, first edition, 1549. Of the " lost " or unpublished works, on which there is some evidence, the following are the most important:-De Metallicis et Machinis, De Ortu Metallorum Defensio ad Jacobum Scheckium, De Jure et Legibus Metallicis, De Varia Temperie sive Constitutione Aeris, De Terrae Motu, and Commentariorum, Libri VI. The known published works upon other subjects are as follows:-Latin Grammar, first edition, 1520; Two Religious Tracts, first edition, 1522; Galen (Joint Revision of Greek Text), first edition, 1525 ; De Bello adversus Turcam, first edition, 1528 ; De Peste, first edition, 1554. The lost or partially completed works on subjects unrelated to mining, of which some trace has been found, are:-De Medicatis Fontibus, De Putre¬dine solidas Partes, etc., Castigationes in Hippocratem, Typographia Mysnae et Toringiae, De Traditionibus Apostolicis, Oratio de rebus gestis Ernesti et Alberti, Ducum Saxoniae.

Jan 1, 1950

By George J. Bancroft

It is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Dansactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,' showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny? distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many. of Prof. Kemp's ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.V his theory, dealing with the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1908

By Franklin G. Pardee

IN 1920 the Minnesota Tax Commission estimated a reserve of 1,341,674,538 long tons of iron ore in Minnesota, the Michigan State Tax Commission report showed 199,092,855 long tons in reserve in that state, and the Wisconsin Geological Survey set the Wisconsin reserves at 21,500,000 long tons. The total reserve that year for the Lake Superior District amounted to 1,562,267,393 long tons. Ten years later the reserves of iron ore in these same districts were Minnesota 1,235,227,510, Michigan 168,349,823, and Wisconsin 23,000,000, or a total of 1,426,577,333 long tons. The decrease in ore reserves in this ten-year period was 135,690,060 long tons, but the shipments were 520,746,975 long tons. In other words, the ten-year depletion in reserves was only 8.68 per cent. If similar conditions carry into the future this calculation would indicate a life for the ore reserves of the Lake Superior region of over 100 years.

Jan 1, 1933

Do not write until you have something to say. Think first; then write. In order to be understood, you must know what you wish to say. Clear writing is the consequence of clear thinking. Therefore consider your subject well before you begin to write; ruminate on it; marshal the salient facts in your mind; saturate yourself with the ideas you wish to express and with cognate ideas; then express yourself deliberately. If you are bubbling over with your subject the words will come, but you might as well expect to sail without a breeze as hope to give life to words without the living thought. Here I may advert to the fact that among the uneducated it is a common expectation to acquire the knack of writing without taking the trouble to study the art of literature. I overheard a woman in a suburban train remark to her neighbor: "I'd like to be able to write well without stopping to think about it". She was one of many that would like to do a thing well without the trouble of thinking; but it cannot be done in respect of anything to which thought is essential. The possession of a good voice does not justify a person in expecting to sing successfully to a large audience; before singing in public one has to master the technique of singing; one has to learn first how to breathe properly, how to enunciate, and many other things. The successful singer is an artist, not a megaphone. Most of us would regard a man or a woman without any training in the art of singing as a fool or an impostor if he or she were to give a public concert, yet we do not recognize the equal foolishness and imposture of persons that write books before they have studied the technique of writing. That is why so many books are unreadable, and why many books by clever men are difficult to read. They start to write books before

Jan 1, 1931

By M. Cohen, D. Caplan

The scaling characteristics of three Fe-Cr alloys have been investigated by determining their weight gain vs. time curves at 1600° to 2000° F. The scales formed thereby have been examined using the techniques of X-ray diffraction and spectrographic and metal-lographic analyses in an attempt to explain the discontinuities in the curves and to elucidate the mechanism of scaling. DESPITE the considerable number of investigations that have been carried out on heat resistant alloys, the characteristics of the scales formed at high temperatures are not fully known. The research reported here was undertaken in an attempt to ascertain the mechanism of scaling of the stainless steels. Scaling experiments were carried out first, the weight increase of the specimens being followed continuously with time. It was observed that, as well as showing the expected decrease in oxidation rate with time, the oxidation curves showed breaks corresponding to intermediate periods of accelerated oxidation, after which protectiveness again increased. This phenomenon was observed with austenitic stainless steels (types 302, 309, and 330) and with Fe-Cr alloys (types 410, 430, and 446), but only the latter are treated in this report. An examination of the scales was made using the techniques of X-ray diffraction and spectrographic and metallographic analyses in an attempt to obtain a correlation between the nature of the scales and the oxidation curves. A search through the literature revealed only a very few previous reports of such periods of accelerated oxidation. Dunn' found breaks in the oxidation-time curves of some Cu-Si alloys but saw no rational explanation of the phenomenon. Heindlhofer and Larsen2 attributed a discontinuity in the weight gain-time curve of iron at 1290°F to the formation of blisters, the subsequent cracking of which exposed an unprotected surface and permitted rapid oxidation until a new protective scale had been reestablished. They advanced no explanation, however, for what they termed the peculiar behavior of a 27 pct Fe-Cr alloy at 2000°F which gained weight very rapidly in between two periods of very slow weight gain. Portevin, Pretet, and Jolivet3 in describing breaks in the weight gain-time curves of Fe-A1 alloys suggested that they might be associated with the occurrence of localized and deeply oxidized areas on the specimens. Bandel4 in a general discussion of oxidation curves of heat resistant alloys considered that the discontinuities were due to a local disruption of the protective layer by the growth of iron-rich oxides. Day and Smith" in their report on the scaling of a large number of iron alloys noted but did not explain occasional relatively rapid changes in oxidation rate at higher temperatures. Chevenard and Wache6 found breaks, often two per specimen, in the oxidation curves of an 18-8 type alloy. They suggested that the cause might be a depletion in chromium of the surface layer of metal due to its selective oxidation, the resultant high concentration of iron and nickel in the scale leading to a poorly protective scale. McCullough, Fontana, and Beck' explained the breaks in the oxidation curves of types 304, 430, and 410 alloys as due to mechanical ruptures. Experimental Work Table I lists the chemical compositions of the materials used. Cylindrical specimens 1/4 in. in diam and 11/2 in. long were machined from cold rolled % in. rod. After a fine finish cut with a sharp tool, the specimens were abraded while still mounted on the lathe with Nos. 2, 1, 0, and 00 metallographic grade emery papers. A 3/64 in. hole was drilled at a distance of 1/8 in. from one end to permit suspension in the furnace. Specimen Nos. 1, 2, and 3 were tested with this surface preparation. All others, after being similarly prepared, were electropolished in a perchloric-acetic electrolyte, electrical contact being made by pressing a tapered platinum hook into the drilled hole. The specimens were then washed in hot water, rinsed with distilled water, rinsed with methanol, dried at 120°F, and weighed. Thereafter,

Jan 1, 1953

By R. S. Wagner, W. C. Ellis

A new mechanism of crystal growth involving oapor, liquid, crnd solid phases explains many observations of the effect of implurities in crystal growth from the vapor. The role of the impuuitq is to form a liquid Solution with the crystalline tnalerial to be grown from the vapor. Since the solution is n prefevred site for deposition firorti the uapor, the liquid becorrles supersaturated. Crystal growth occurs by precipitatzon from the supersaturated liquid crt tlie solid-liquid zntevfnce. A crystalline defect, such as a screw dislocation, is not essetztial for VLS (vapor -liquid-solid) growth. The concept of the VLS mechanism is discussed in detail with reference to tire controlled growth of silicon crystals using gold, platinum, palladium, nickel, silver, or copper as an implurity agent. RECENTLY a short communication' described a new concept of crystal growth from the vapor, the VLS mechanism. In this paper we present a detailed description of the process and its application to the growth of silicon crystals and we discuss its relevance to existing concepts of .'whisker" crystal growth. Crystal growth from the vapor is usually explained by a theory proposed by Frank2 and developed in detail by Burton, Cabrera, and Frank.3 In this theory a screw dislocation terminating at the growth surface provides a self-perpetuating step. Accommodation of atoms at the step is energetically favorable, and is possible of much lower supersatu-ration than required for two-dimensional nucleation. Crystals of a unique form resulting from aniso-tropic growth from the vapor are "whisker" or filamentary ones. Such crystals have a lengthwise dimension orders of magnitude larger than those of the cross section. For most filamentary crystals both the fast-growth direction and directions of lateral growth have small Miller indices. The special growth form for a whisker crystal implies that the tip surface of the crystal must be a preferred growth site. sears4 proposed that, according to the Frank theory. a whisker contains a screw dislocation emergent at the growing tip. Such an axial defect provides a preferred growth site and accounts for unidirectional growth. The hypothesis was extended by Price. Vermilyea. and Webb," still implying the presence of a dislocation at the whisker tip. They postulated that impurities arriving at the fast-growing tip face become buried while those arriving on the surface of slow-growing lateral faces accumulate and thereby hinder growth. These considerations led to a whisker morphology. There is increasing evidence that most whisker crystals grown from the vapor are dislocation-free. Webb and his coworkers6 searched for an Eshelby twist7 in zinc? cadmium, iron. copper, silver, and palladium whisker crystals. They found unequivocal evidence for an axial screw dislocation in only one element, palladium. However, not every palladium crystal examined contained a dislocation. Observations with the electron microscope have failed to show dislocations in whisker crystals of zinc, silicon.9 and one morphology of AlN.10 Since many whiskers are completely free of dislocations, an axial dislocation does not appear to be required for whisker growth of many substances. A significant advance in understanding whisker growth has been a recognition of the need for impurities. This requirement has been clearly demonstrated for copper,11 iron,13 and silicon9-1 whiskers. For silicon, detailed studies proved conclusively that certain impurities, for example, nickel or gold, are essential. Another pertinent phenomenon which has received little attention is the presence of a liquid layer or droplets on the surface of some crystals growing from the vapor. Crystals in which this has been observed include p-toluidine,14 MoO3,15 ferrites,16 and silicon carbide.'" The liquid layers or globules were considered to be metastable phases, molecular complexes, or intermediate polymers originating from condensation of the vapor phase. The possibility has been suggested that the halide being reduced is condensed at the tip18 or adsorbed on the surface11 of a growing metal whisker, for example copper. The literature on whiskers discloses illustrations of rounded terminations at the tips. These appear. for example, on crystals of A12O3,19,20 sic,21 and BeO.22 For BeO, Edwards and Happel suggested that during growth of the whisker the rounded termination consisted of molten beryllium enclosed in a solid shell of BeO. A recent paper9 on the growth of silicon whiskers contains many observations pertinent to an understanding of the mechanisnl of whisker growth. These observations are summarized as follows. 1) Silicon whiskers are dislocation-free. 2) Certain impurities are essential for whisker growth. Without such impurities the silicon deposit is in the form of a film or consists of discrete polyhedral crystals.

Jan 1, 1965

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese: they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way: there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution arrived.

Jan 6, 1976