Search Documents

By F. R. Jones

AT Tahawus, N. Y., National Lead Co. operates the MacIntyre development. Here the world's largest titanium mine produces 5200 long tons of ore per day and pours 8000 long tons of waste rock over its dumps. Concentrated ilmenite is sent by rail to National Lead Co. pigment plants, and a second product, magnetite, is sold to steel producers in raw form or is agglomerated and shipped as sinter. Several earlier attempts had been made to produce iron from the deposits, which have been known since 1826. These attempts failed, chiefly because of titanium impurity. In 1941 the present owners reestablished the operation for production of war-scarce ilmenite, and the impurity became the main product. The Ore: The MacIntyre ore zone is about 2400 ft long and 800 ft wide in horizontal measurements. Ore outcrops were found on the northwest side of Sanford Hill, 450 ft above Sanford Lake and 2500 ft southeast. The zone dips at about 45" toward the lake and plunges to the southwest. The ore minerals, ilmenite and magnetite, are unevenly distributed in bands roughly parallel to the long axis of the ore zone and are interspersed with bands and horses of waste. Hanging wall ores are fine grained and grade from rich ore to waste rock or gabbro. Footwall ores are coarse grained and are almost entirely ilmenite and magnetite. The foot-wall waste rock, anorthosite, is the common country rock. Several faults cut the ore zone. These faults have no great displacement but do contribute to the great physical variations in ore rock and surrounding waste. The Mine: The MacIntyre mine is an open pit operation, with benches at 35-ft intervals. The lowest bench is now 54 ft below lake level. Loading equipment consists of three electric-powered shovels (a P & H model 1400 with 4-yd dipper and two Bucyrus-Erie models 85-B with 2%-yd dippers) and one diesel-powered shovel (a Northwest model 80D with 2%-yd dipper). Ore and waste are transported to a 48x60-in. jaw crusher in ten 22-ton Euclid trucks with 300-hp diesel engines. Ordinarily the two Bucyrus-Erie 2 % -yd shovels load ore into a fleet of three or four trucks. This combination works two 8-hr shifts per day, moving 5200 long tons of ore to the crusher and removing a small portion of the waste rock. The P & H model 1400 shovel, with a fleet of four trucks, loads waste on three shifts per day. The mine operates on a 5-day week, with a small maintenance crew working Saturday. Oversize rock is broken by a dropball handled by an Osgood model 825 rubber-mounted crane.' Ore and waste are broken by drilling and blasting 9-in. diam vertical holes behind the benches. Bucyrus-Erie 42-T churn drills are used to drill the holes, which are extended 4 ft below the bench level on which the broken rock will fall. Drilling and Blasting History: In its early years the mine was equipped with Bucyrus-Erie 29-T churn drills, which drilled 6-in. holes. To keep up with production requirements the hole diameter was soon increased to 9 in., and by 1950 the three 42-T drills now in use had been acquired. Early blasting experiments with different kinds and grades of explosive led to adoption of 90 pct straight gelatin dynamite as standard. It was recognized that this explosive was expensive, and from the start of operations until 1950 extensive experiments were made using blasting agents of the ammonium nitrate family. Results were recorded as uniformly poor, with great build-up of oversize rock. The expense of these experiments, and the discouraging results, caused the abandonment of any expectation of breaking MacIntyre rock with anything but 90 pct straight gelatin dynamite. Further standardization led to 9-in. well drillhole spacings set at 16 ft in ore and 18 ft in waste, exceptions being permitted only for unusual conditions. The hole burdens were theoretically about 22 ft. Due to the extreme back-slope of bench faces, caused by blasting with heavy charges of dynamite, actual burdens were commonly well over 30 ft. Lack of precise control resulted in many holes having a burden as light as 15 ft. General practice was to stem 6 or 7 ft of hole with magnetite concentrate, the amount of stemming being left to the discretion of the pit foreman. Usually all holes in a row were fired instantaneously with Primacord detonating fuse. Millisecond delays were

Jan 1, 1957

By A. Hansson, G. E. Tardiff

WHILE it is generally known that cold-worked low-and medium-carbon steels exhibit substantial increases in tensile rupture ductility with increased deformation velocity172 (up to the von Karman limit), the observations for annealed or normalized steel do not permit simple generalization. Various investigators, for example, have reported both small increases1,3 and small decreases4,5' in rupture ductility with increased rates of deformation of normalized low-carbon steel. The purpose of the present note is to report on the dependence observed for strain-aged steel since preliminary work here indicates that strain aging results in the development of a consistent type of behavior that is understandable in the light of current knowledge of the lower yield dynamics for steels which deform inhomogeneously.6 This realization throws additional light on the influences responsible for the behavior of normalized steel. The results presented here were obtained for a 0.21 pct C, 0.012 pct N sheet (0.012 in. thick) steel which was received in a temper-rolled condition (approximately 3 pct reduction in thickness after process annealing); the as-received material had a spherodized structure with a ferritic grain size of ASTM 8. The material was selected for testing after 6 months room temperature aging, at which time the static lower yield and ultimate tensile strength measured 79 and 82 kpsi, respectively. ASTM 2-in. reduced section, 1/2-in.-wide specimens were used in smooth bar tests and 3/4-in.-wide specimens containing two 60-deg opposed edge notches (root radii = 0.002 in.) were used in notched bar tests. To facilitate strain measurement, the smooth bars were blued with ink and marked at 0.1-in. intervals along the gage length; the notched

Jan 1, 1968

By R. B. Moore

IN 1914 the writer and K. L. Kithil announced, through Bulletin 70 of the U. S. Bureau of Mines, that the United States possessed the largest deposits of radium-bearing ore in the world. At that time a small amount of this ore was being, mined and shipped to Europe, and one company was preparing to start the extraction and recovery of radium in this country. The importance of our carnotite deposits in Colorado and Utah up to the publication of Bulletin 70 was not, however, appreciated by anyone.. At that time the total supply of radium in the world was about 10 g., calculated as element, and when I estimated that at least 100 g. of radium element, and probably 200 g., would be produced from our carnotite deposits, there was a considerable amount of skepticism. Up to the present time almost 200 g. have come from this ore, and some writers put this figure a little higher. Uranium ore was found in the copper mines of the Union Minière du Haut-Katanga at Luiswishi in 1913. Later discoveries were made at other places in the Belgian Congo, and the Katanga ores now represent the largest supply of radium-bearing ore in the world. In fact, since 1923 very little radium has been produced from American carnotite, the Katanga ore representing practically the world's supply of. radium since that date.

Jan 1, 1930

Jan 1, 1939

The John Fritz Medal is awarded from time to time for notable scientific or industrial achievement by a board composed of representatives from the four engineering Societies. The members of the Board of Award for 1917 are: A. S. C. E. A. S. M. E. George F. Swain Ambrose Swasey, Charles Warren hunt, John, A. Brashear, Charles D. Marx, Frederick R. Hutton, Clemens Herschel. John R. Freeman. A. I. M. E. A. I. E. E. Gybbon Spilsbury, C. 0. Mailloux, Charles F. Rand , Paul M. Lincoln, Christopher R. Corning, John J. Carty, Benjamin B. Thayer. Harold W. Buck. The John Fritz Medal was awarded in January, 1917, to Dr. Henry Marion Howe, for his "investigations in metallurgy, especially in the metallography of Iron and Steel." The presentation ceremonies were held in the Auditorium of the United Engineering Societies' Building, New York, on Thursday evening, May 10. Mr. Ambrose Swasey, Chairman of the John Fritz Medal Board of Award, presided, and addresses were delivered by Dr. Rossiter W. Raymond, Secretary Emeritus of the American Institute of Mining Engineers, and Dr. Ira N. Hollis, President of the American Society of Mechanical Engineers. Professor Albert Sauveur, Chairman of the Board at the time the award was made, presented the medal, and the ceremonies concluded with the response of Dr. Howe.

Jan 7, 1917

By G. R. Fritterer

Investigators in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial temperatures; i. e., 1000 to 1800 C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree. New Thermoelectric Materials A thorough survey of the literature on thermoelectricity revealed that present-day thermocouples could not meet the specifications mentioned above because their thermoelements are metallic. Metals have a marked tendency to deteriorate chemically and their melting points limit their use to low temperatures. Refractory substances, however, are usually resistant to chemical attack and are quite stable at high temperatures. Hence a survey of refractory substances having thermoelectric possibilities was made. One class of thermocouples considered was that in which carbon and a carbide of some metal or nonmetal were the thermoelements. Previous investigators neglected to study this field but certain recommendations were made by them for the use of couples in which carbon served as one element. These proposals are listed in Table 1. The couples suggested are unsatisfactory because of their low thermoelectric powers, the low melting points of their metallic elements, etc. The

Jan 1, 1933

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By R. M. Brick, F. L. Vogel

THE elementary mechanism of deformation in the body-centered cubic metals has been a subject of dispute for many years. If the problem were merely that of designating the crystallographic plane or planes of slip, the solution would have appeared long ago. However, there must be greater differences in the deformation behaviors of the body-centered and face-centered types than the differences in their lattices would suggest. The lines of slip formed on the polished surface of a strained face-centered cubic metal conform to glide over a single plane of the crystal. Slip in body-centered cubic iron, however, is frequently observed as curved and forked lines which could not possibly define a single plane of atoms. This alone is sufficient reason to expect different modes of deformation to operate in the two lattice types. The literature in this field now has generally accepted the proposition that {110), {112), or (1231 planes will act as slip planes in iron. It is essential that the experimental evidence supposedly supporting this proposition be critically examined. Taylor and Elam1 in 1926, using relatively small single crystals, determined the operative slip systems by measurements of the distortion of a grid engraved on the specimens prior to deformation. Their results indicated that shearing had taken place in the close-packed direction on a plane adjacent to or coinciding with the plane of maximum shear which contained the slip direction. This led the authors to propose a theory of noncrystallographic or banal slip. The authors considered an alternate rationalization of banal glide. Slip on two (1101 planes or possibly two {112} planes containing the same <1ll> direction could produce the wavy slip lines. By employing plane segments of varying widths, the integrated plane could take any position in the <111> zone. They rejected this explanation, however, feeling that the preponderance of evidence was against it. Taylor&apos; continued the investigation of the plasticity of the body-centered cubic lattice on ß brass. He reasoned that the resistance to shearing of a given plane in the zone of the slip direction was a function of the angle between the glide plane and the closest (110),: P F=—cose sine cos(X —?) [1] where F is the resistance to shear; P, the axial load at yielding; A, the cross sectional area; e, the angle between slip direction and load axis; x, the angle between plane of maximum shear containing the slip direction and the (101) pole; and ?, the angle between observed glide plane and the (101) pole. Differentiating Eq. 1 and rearranging, dF — = tan(x-?) d? [2] F which expresses the variation of the shear resistance with the angle $. Integrating this equation between the limits 0 and ? yields In F/F0 = ?0?tan(x— ?) d? [3] Here, F, is the resistance to shear of the (110) plane and F is the resistance to shear of a plane $ degrees from the (110). Thus, the variation of shear resistance with $ can be calculated from an experimentally measured x vs $ relationship. Fahrenhorst and Schmid8 sed several methods, none of them involving direct observation, to determine the glide system in ferrite. They determined the variation of critical resolved shear stress with

Jan 1, 1954

Albin, B. R Billings, Mont. &apos;28 Amster, Nathan L . , 25 Broad St, New York, N. Y. &apos;28 Bache, Jules S 42 Broadway, New York, N. Y. &apos;28 Barrett, C. P 5338 Harper Ave, Chicago, Ill. &apos;28 Baum, Frank G Hobart Bldg., San Francisco, Cal. &apos;28 Bayless, Ron. William S Russ Bldg , San Francisco, Cal. &apos; 28 Bean, Louts H., V.P., Dwight P. Robinson & Co, Inc 125 E. 46th St, New York, N Y. &apos;23 Beatty, Ross J 1105 First National Bank Bldg., Chicago, Ill. &apos;28 Benwell, Oswald F 205 Colorado National Bank, Denver, Colo. &apos;28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. &apos;28 Bingham, Charles W 1542 Hanna Bldg, Cleveland, Ohio. &apos;28 Blumenthal, Hugo 44 Pine St, New York, N. Y. &apos;28 Boettcher, Charles Ideal Cement Bldg., Denver, Colo. &apos;28 Bowlus, Thomas H Iola, Kans. &apos;28 Bragg, E. B Carmel, Cal. &apos;28 Brown, Colvin B Chamber of Commerce, Washington, D. C. &apos;28 Burt, Maxwell Struthers Southern Pines, N. C. &apos;28

Jan 1, 1923

W. H. BASSETT, * Waterbury, Conn.-Manganese should not be expected to remedy all the defects that are due to poor melting practice. It is undoubtedly valuable in helping to eliminate porosity in many of the alloys. In the copper-nickel alloys, its use is becoming almost universal, for, beside helping to make sound castings, it tends to hold the carbon in solution in the solidified alloy. GWILLIAM H. CLAMER,? Philadelphia, Pa.-I have found that manganese copper is satisfactory for eliminating sulfur and that it works very well in the crucible and when you have reducing conditions; but in a large reverberatory charge, where the conditions are oxidizing, we were not able to eliminate the sulfur.

Jan 1, 1919

Executive-A. R. LEDOUX, chairman. Membership-J. V. W. REYNDERS, chairman. Finance-J. V. N. Dorr, chairman. Library-E. GYBBON SPILSBURY, chairman. Papers and Publications-BRADLEY STOUGHTON, chairman. Nominations-POPE YEATMAN, chairman.

Jan 12, 1919

By James A. Crookston, William D. Fitzpatrick

Committee C-8 of the American Society for Testing and Materials defines refractories as "material, usually nonmetallic, used to withstand high temperature," and it defines the term refractoriness thus, "in refractories, the capability of maintaining the desired degree of chemical and physical identity at high temperatures and in the environment and conditions of use.” The ability to withstand high temperatures is critical to classifying a material as a refractory. However, as the foregoing definition of "refractoriness" implies, the refractory material may be subjected to and is expected to resist not only high temperatures but a variety of other destructive forces incidental to its use. These include abrasion, impact, thermal shock, chemical attack, and high level loads at high temperatures. The various industrial applications of refractories represent an infinite variety of combinations and degrees of severity of these destructive forces, including high temperatures. Naturally, such a variety of application conditions leads to a need for a wide variety of refractory products to satisfy those conditions. The number of refractory products available is great enough that some form of classification is necessary to a discussion of refractories. Refractories may be classified in several ways, but the most suitable one is based on their general compositions and to lesser degrees on their physical condition and distinctive properties. The primary types of brick include aluminosilicate brick (fire clay and alumina), basic brick (magnesia and chrome ore, alone and in various combinations), silica brick, insulating brick, and special refractories (carbon, SiC, ZrO2, zircon, borides, and nitrides). Brick is, of course, preformed and usually is heat treated at high temperatures before use, but in some instances is unburned and/or chemically bonded, including the relatively new class of tar-bonded magnesia and/or dolomite brick. In addition to preformed refractories, another broad category includes the so-called specialty refractories, which are usually made in the same types as itemized for brick-bonding mortars and high temperature cements, hydraulic setting castables or refractory concrete, plastic firebrick, and ramming mixes. Refractory grains, such as fire clay and high alumina calcines, dead-burned magnesite and periclase, and dead-burned dolomite are also considered refractory products. Bricks are also classified on the basis of physical dimensions, as standard sizes and special shapes. The standard sizes are those which are of definite shape and design and are designated as 228.6 x 114.3 x 63.5 mm (9 x 4 ½ x 2 ½ in.) and 228.6 x 114.3 x 76.2 mm (9 x 4 ½ x 3 in.) straights and series. Bricks of nonstandard sizes are referred to as special shapes. These come about as a result of a particular need for a given furnace or for a particular application. Types and Classes of Refractories Fire Clay Refractories Classification: Fire clay refractories, as the name implies, are composed essentially of fire clay and/or calcined fire clay in varying proportions. The ASTM Standard Classification of Fireclay and High Alumina Refractory Brick, C27-70 (reapproved 1976), gives five classes of fire clay brick designated as super-

Jan 1, 1983

By Fred W. Gordon

It is my purpose to call attention to the close approximate correctness of certain coefficients and formulas concerning the flow of gases, and their applicability to the practical construction of flues and

Jan 1, 1886

By M. Gensamer

THE stresses which initiate deformation processes in metals are funda-mentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals1 has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.2 It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. ? Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals.

Jan 1, 1938

By Frank Alfred Fahrenwald

Discussion of the paper of FRANK ALFRED FAHRENWALD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 103 to 149. F. A. FAHRENWALD, Cleveland, Ohio (communication to the Secretary*).-Since the publication of my paper in the January Bulletin, (which was largely a metallographic treatise), I have been questioned regarding two points referred to therein. One of these is that which deals with the application I have made, p. 119, of the equation for melting pressures which correspond with different working temperatures. The other refers to the statement, p. 137, that "Prolonged heating at relatively low temperatures gave fewer and larger crystals and crystals of different sizes, while a flashing at higher temperatures gave a very fine and uniform crystalline structure, which was much&apos; to be preferred." Especial emphasis was not placed upon either of these two factors, for each seemed perfectly logical and obvious. As they do not seem to be self-explanatory, I will supplement with those portions of my notes which were purposely omitted from the manuscript submitted for publication. A few practical illustrations may serve as evidence in support of the first of these, but it must be understood that in this work the "amorphous theory" is considered as being sound, and that it is assumed that metals allow of distortion, without fracture, by virtue of the formation of slip surfaces, accompanied by the transformation of crystalline material to the, amorphous phase. Effect of Pressure.-In all forging, rolling, and drawing operations, it is known that specimens of small cross-section may be worked at a lower temperature than can be used for the same material in much greater mass and sectional area. In -the larger pieces the maximum pressure is brought to bear upon the material near the surface, so that the interior is not subjected to great pressure, but to, a stress more nearly tensile, or shearing, so only the surface is subjected to the critical melting pressure. In the case of wires which draw hollow, the center is subjected to practically a tensile stress which breaks it, while the surface skin draws perfectly, due to the enormous "flowing" pressure exerted upon it by the surface of the draw-plate.

Jan 5, 1916

By S. M. Wu, R. L. Stone, T. D. Tiemann

The dissolution of silica from quartz in sodium hydroxide solutions was investigated by statistical methods. A second-order predicting equation was developed with 28 experiments expressing the dissolution of silica as a function of the variables quartz size, time, temperature and sodium hydroxide concentration. With this equation a comprehensive picture of the dissolution reaction was gained which included the effect on extraction of each variable and their interactions, fractional extractions, reaction rates and activation energies. A previous investigation of the extraction of silica from low grade siliceous iron ore by digestion in sodium hydroxide solutions presented the extraction as a function of time, temperature and sodium hydroxide concentration.&apos; The present paper is an outgrowth of the previous work and develops by a mathematical analysis the functional relationship between the extraction of silica and time, temperature, sodium hydroxide concentration and particle size. Relatively pure quartz was used in this study in order that the basic quartz-sodium hydroxide reaction could be studied without the influence of other constituents that are commonly found in iron ores. The functional relationship between the dissolution

Jan 1, 1965

By E. W. Henderson

Oil and gas development in Utah in 1936 added nothing of importance to the commercial possibilities of the state and consisted principally of efforts to reach objectives in wildcat wells started prior to 1936. Leasing activity on structures having oil and gas possibilities in beds of Pennsylvanian age or older followed announcement by the Standard Oil Company of California that a test of beds of Mississippian age would be made on the San Rafael structure. DRilling Clay Basin, Dagget County.—The Mountain Fuel Supply Co. completed a third well, sec. 16, T. 3 N., R. 24 E., on a flank of this structure. Total developed open flow of the field is approximately 50 million cubic feet and sufficient reserve has been established to warrant construction in 1937 of a pipe line connecting with the Salt Lake City-Ogden line. San Rafael, Emery County.—The Standard Oil Company of California started a wildcat test in sec. 22, T. 23 S., R. 11 E. Circulation was lost in a water-filled cavity, in dolomitic limestone, below 2185 ft. and the hole conditioned as a water supply for drilling a second test in sec. 27, T. 23 S., R. 11 E. The Carter Oil Co. in 1921 drilled a well in sec. 24, T. 23 S., R. 11 E., which was abandoned at a depth of 3035 ft. after testing at least a part of the Pennsylvanian section. Czsco, Grand County.—Drilling operations at the Utah Sout.hern Oil Company&apos;s test in sec. 33, T. 22 S., R. 22 E., continued throughout the year. Information obtained by means of a seismographic survey of the area indicated that beds of Pennsylvanian age would be found at approximately 2500 ft. The bottom of the hole at 6300 ft. is believed to be in beds of Pennsylvanian age but positive determination has not been made froin the drill cuttings. Green River, Grand County.—Test of Glen Ruby et al., sec. 34, T. 21 S., R. 16 E., was abandoned at 2627 ft. as a dry hole after drilling into Permian Kaibab limestone. Shows of oil and gas were reported and a flow of carbon dioxide gas under low pressure encountered.

Jan 1, 1937

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan&apos;s total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan&apos;s total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943