Search Documents

By T. H. Alden

T. H. Alden (General Electric Research Laboratory)—This paper as well as earlier ones of Dr. Wood represent an important contribution to the experimental description of fatigue fracture. The mechanism of fracture proposed by the authors, however, is not established by this data nor supported by other data existing in the literature. Although taper section metallography provides a rather detailed picture of fatigue crack geometry, photographs so obtained must be interpreted with care. The narrow bands revealed by etching, frequently associated with surface notches, are labeled by the authors "fissures". Measurement shows, taking into account the 20 to 1 taper magnification, that the depth of these structures is at most 2 to 3 times the width. This distinction is important in the conception of a mechanism of crack formation. It is difficult, for example, to imagine a deep, narrow fissure arising from a "ratchet slip" model. A surface notch, on the other hand, may form easily by this mechanism. The notches observed in the present work are the subsurface evidence of the surface slip bands or striations in which fatigue cracks are known to originate.4-6 It is clear that an understanding of the structure of these slip bands is of key importance in understanding the mechanism of fracture. The evidence presented shows that these regions etch preferentially, possibly because they contain a high density of lattice defects, or as the authors state equivalently, because they are "abnormally distorted." However, it is not possible to conclude that the distortion consists of a high density of vacant lattice sites. The fact of a high total shear strain in itself does not assure a predominance of point defects as opposed to other defects, for example, dislocations. Other evidence in the literature which suggests unusual densities of point defects formed by fatigue7-' refers not to the striations or fissures, but to the material between fissures (the "matrix"). If a choice must be made, the preferential etching would seem to be evidence for a high dislocation density, since dislocations are known to encourage chemical attack in copper;g no such effect is known for the case of point defects. A third alternative is that the slip bands are actually cracked, but that near its tip the crack is too narrow to be detected by the authors' metal-lographic technique. In this case the rapid etching can be readily understood in terms of the increased chemical activity of surface atoms. Unless a vacancy mechanism is operative, the motion of dislocations to-and-fro on single slip planes will not lead to crack growth. Point defect or dislocation loop generation are the principal non-reversible effects predicted by this model. In any case, the nonuniform roughening of the surface in a slip band6 requires a flexibility of dislocation motion which is not a part of the to-and-fro fine slip idea. The same is probably true of crack growth by a shear mechanism. Either some dislocations must change their slip planes near the end of the band and return on different planes,'0 or dislocations of opposite sign annihilate." The mechanism by which these processes occur in copper at room temperature or below is that of cross slip. Thus cross slip appears to be essential to fatigue crack growth.6'10"12 The fact that a tensile stress opens the slip bands into broad cracks does not indicate the structure of the bands or the mechanism by which cracks form. The charactersitic concentration of slip into bands during fatigue shows a low resistance to shear strain in these regions. (This fact in itself may be inconsistent with a high concentration of vacancies.) The authors contend also that continuing shear produces an additional mechanical weakening so that the bands fracture easily (are pulled apart) under the influence of the superimposed tensile stress. It is equally possible that the only weakness is a weakness in shear, that the crack propagates by a shear mechanism, and that subsequently the tensile stress pulls the crack apart. Even the direct observation of bands opened by a tensile stress would not be conclusive since, as argued above, they may be fine cracks. The same argument applies to internal cracks, their existence in the presence of a tensile stress not indicating the mechanism of formation. Internal cracks originating in regions of heavy shear have also been seen following tensile deformation of OFHC copper,13 so that this mode of fracture is not unique to combined tensile and fatigue straining. The authors point out in their companion report14 that 90 pct of the cracks formed during pure tor-sional strain were within 8 deg of the normal to the specimen axis. If the tensile stress were an important factor in crack propagation, it is surprising that the cracks cluster about the plane in which the normal stress vanishes. Similarly, a study of zinc single crystals showed that for various orientations the life correlated well with the resolved shear stress on the basal plane,'= and was not dependent on the normal stress across this plane. W. A. Wood and H. M. Bendler (Authors' reply) -Dr. Alden's discussion emphasizes the essential point in the relation of slip band structure to

Jan 1, 1963

By David Mitchell

THE production of fluorspar is one of the smaller nonmetallic indus-tries in the United States with a capital investment-about $10,000,000. Shipments from United States mines' in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications: Consump- Specifications, Per Cent Use Form tion in 1936, Per Cent CaF2 SiO2 Fe2O3 Metallurgical Gravel 79 +85 -5 or lump Ceramic,. Ground 10 +95 -3 -0,1 Acid Ground 11 +98 -1 The concentration of the coarser sizes presents relatively little diffi-culty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938

By J. C. Swartz

New measurements of graphite and cementite solubilities in ferrite have been obtained to resolve disagreements among previous data. To measure graphite solubility, specimens of iron were equilibrated with rarious carburizing atmospheres at temperatures be-twee~z 480" and 1435°C. The carbon activity of each atmosphere relative to graphite was taken from published data. After quenching from each equilibration treatment the concentration of carbon (typically 10 pprn by wt) was determined from the height of the Snoek peak in the internal friction spectrum. A few inclividual analyses by combustion support the reszdts of Smith on the solubility of graphite near the eutectoid temperature. Combination of these combustion and internal friction analyses determines In a, (at 0.01 wt pct) = 24,000/RT - 12.72, where a, is the activtity relative to graphite in ferrite at fixed cornposition. The same specimens were used to determine the solubility of self-stressed cementite precipitates. The results indicate solubilities of 6.3, 23.2, and 68 pprn carbon by wt at respectively 400°, 500". and 600°C. The once large discrepancy between the cementite solubility determined by internal frictiori and that calculated from flee energy data has been almost completely resolved. A recent study1 (hereafter designated I) on the solubility of cementite in a iron did not fully resolve the disagreement among previous data. The remaining disagreement is illustrated by the phase diagram in Fig. L The data of I are represented by the line labeled "stress-free" cementite. They determine a heat of solution of cementite of (14.8 * 0.2) kcal per mole which contrasts with the (20 * 1) kcal per mole derived from Smith's graphite solubility2 and the formation energy of cementite.3 Toward resolving this disagreement we have obtained new data on the solubilities of graphite and cementite. METHODS As in I the Snoek peak in the internal friction spectrum was used to measure the concentration of carbon dissolved in ferrite. This method relies on the relation C=kQ-1 [1] in which C is the concentration of dissolved carbon, Q-I is the Snoek peak height, and k is a proportionality factor which is a function of the peak temperature, polycrystalline texture, and other parameters characteristic of the ferrite lattice. To determine true heats of solution via Eq. [1], it is necessary to establish that k is independent of the temperature from which the specimen is quenched. Some evidence on this point is contained in a separate report.* Additional evidence is shown by the data points in Fig. 1. These represent the Snoek peaks of two specimens carburized to about 10 ppm C, copper plated, and quenched first from 888º then from 588°C. The copper plate was removed before each Snoek peak measurement. These data show that there is no detectable dependence of k on quenching temperature. The solubility of graphite was determined by repeatedly carburizing various specimens of iron wire with gas mixtures of known carbon activity relative to graphite. To cover a wide temperature range within the a phase boundaries it is desirable to use as low a carbon concentration as is compatible with reasonable precision. With the present internal friction apparatus the best compromise of these desires is a concentration near 10 wt ppm. The dashed line in Fig. 1 was used to approximate the activity of carbon* for

Jan 1, 1970

By J. H. Jackson, J. G. Kura, M. C. Udy, L. W. Eastwood

The melting and casting of any commercial metal depends upon the success with which the problems attendant to the handling of the specific metal are overcome. Common difficulties encountered in the handling of commercial metals are tendencies to burn or oxidize excessively, low fluidity, entrapment of dross, hot cracking, cold embrittlement, cold shuts, and un-soundness caused by gas evolution. Beryllium is not only subject to these same difficulties but is generally more sensitive to them than are the more common metals, thus necessitating more exact founding precautions. Characteristics of Beryllium Certain characteristics of beryllium which make it particularly difficult to handle in the plant or laboratory are as follows: 1. The melting point of beryllium is about 2400°F and pouring temperatures vary from 2600 to 2900°F, depending upon the degree of fluidity required. The extreme chemical activity, combined with the high temperatures, makes necessary the use of inert atmospheres, slags, or vacuum for protection during melting and pouring. Furthermore, beryllium tends to react with the melting crucibles, tools, and molds, thus requiring the selection of suitable materials and proper maintenance of these items. 2. The very marked absorption of gas by molten beryllium and the subsequent evolution of gas during solidification causes a great deal of difficulty with unsoundness. Beryllium castings may also be subject to unsoundness as a result of gas formation by chemical reaction with the mold surface during solidification. 3. The very marked chemical affinity between molten beryllium and the normal atmosphere causes the formation of dross. On relatively quiescent melts, this dross forms a very tenacious film which, if carried over to the mold, can cause defects such as the formation of skins or dross in the interior or on the surface of the casting; folds or defects similar to cold shuts may also be found. 4. During the pour and attendant turbulence, the dross may be mixed into the metal and then carried to the casting. There it may be entrapped during freezing and cause internal defects, or it may float to the surface and cause severe dross defects on the cope side of the castings. 5. Solid beryllium is very weak at a temperature near the solidus line; brittleness is also a problem at lower temperatures. Thus, hot and cold cracking must be guarded against. Scope of the Experimental Work All of these problems have been given consideration in the work at Battelle. Before the work was started at Battelle, it was customary to melt beryllium in a vacuum furnace or under flux in graphite-lined induction furnaces. Because of the difficulty of preventing gas unsoundness in beryllium castings, an investigation was undertaken primarily to study this particular problem and, secondarily, to devise methods of overcoming the other difficulties encountered in the founding of beryllium. The objectives of the laboratory work were multifold: 1. To devise a practical method of melting, other than vacuum melting, by means of which consistently sound beryllium castings could be produced. 2. To obtain fundamental data which would promote a better understanding of the causes of gas unsoundness in beryllium. 3. To develop a casting technique which would permit low melt temperatures, minimize dross defects and hot cracking, and eliminate reaction with the mold surface. Up to the present time, a considerable amount of progress has been made on the first and third objectives, with the result that it can now be safely stated that consistently sound castings can be made by the open-pot melting method, using argon as a protective atmosphere and a proper casting technique. There has been some progress on the second objective of the project, but it cannot yet be safely stated that the problem is completely understood. Most of the experimental work has been conducted in an enclosed melting and pouring apparatus in which very-close control of melting variables has been effected. Findings based on the results of the work conducted in this small experimental apparatus have been applied to large-scale melts which have been made by techniques suitable for duplication on a commercial scale.

Jan 1, 1950

By Strathmore R. B. Cooke, Eugene L. Talbot

THE perfluoro acids and derivatives show unusual surface-active properties that qualify them as possible flotation reagents. They lower the surface tension of water from 15 to 20 dynes below that obtainable with the corresponding hydrocarbon compounds.1, 2 Fluorochemicals adsorb very strongly on solid surfaces to give films that exhibit larger contact angles than films of the corresponding hydrocarbons."' * The large contact angles probably result from the terminal —CF3 group. The perfluoro acids are made by electrolysis of the corresponding carboxylic acid in anhydrous hydrogen fluoride.5 From the perfluoro acids many derivatives may be obtained, such as amides, amines, alcohols, xanthates, ethers and esters and others. Since the fluorinated analogues of the conventional hydrocarbon flotation collectors possess enhanced surface properties, a few were selected for testing. Because a survey of all possible minerals and reagent combinations would be out of the question, hematite was chosen to represent a nonsulphide system and pyrite to represent a sulphide system. The fluorinated reagents used in these experiments were prepared in the research laboratories of Minnesota Mining & Mfg. Co. Some were synthesized especially for this research. They are not available cokmercially. Separation of Nonsulphide Ores: The separation of oxides from silica has always been a challenge to the flotation industry because differences in surface properties of the minerals are normally insufficient to produce clean concentrates. Oleic acid," rosin acids,' and amine salts% ave been used to considerable extent to effect separation of metal oxides and silica. The system hematite-silica was chosen to represent the nonsulphides both because of its difficulty of separation and because large tonnages of easily obtainable material are available, such as gravity concentration tailings and nonmagnetic taconites on the Mesabi Range. The wash-ore tailings used here contained approximately 35 pct iron after desliming. Samples of the material used in this work were part of the same lot used by Chang, Cooke, and Huch9 and were prepared in an identical manner. Reagents for Nonsulphide Ores: Since one of the purposes of this investigation was to compare hydrocarbons with fluorocarbons, reagents of known behavior such as oleic acid, and the alkali metal salts of certain resin acids (Dresinates), were established as standards. Hydrocarbons and fluorocarbons of comparable chain length and other experimental fluorocarbons were tried as collectors for hematite. A list of the materials used and the concentrations of their stock solutions are given in Table I. Since silica can be selectively floated from hematite by conventional reagents," a few fluorocarbon reagents were also tried for this purpose. Their composition and concentrations are given in Table 11. Most of these reagents served the dual function of collector and frother. In the case of F-11 flotation did not occur but it served as a frother when F-6 was employed as a collector. Reagent grade sulphuric acid and sodium hydroxide were used to regulate the pH. Deionized water containing less than 0.1 ppm of salts expressed as NaCl was used for all solutions and flotation tests. The pneumatic flotation cell consisted of a 350-ml fritted glass Buechner funnel with a source of filtered air which could be controlled by a needle valve." A 50-g sample of ore and 250 ml of deionized water were added to the flotation cell and stirred slowly. The reagents were added and the pulp was conditioned before air was admitted to the cell. Approximately 15 ml of the pulp were removed for pH determination before flotation was started and were then returned to the system. The pH was again measured after flotation. Air was admitted to the cell until no further flotation occurred or until the character of the float changed markedly. Both the float and the nonfloat products were filtered, dried, weighed. and assayed for iron. The cell was washed in hot water and rinsed with deionized water after each test. Occasionally the cell was cleaned with concentrated hydrochloric acid to remove iron oxide particles from the glass frit. Experimental Results: Above a pH of 8, sodium oleate was an effective collector for hematite. The emulsification of equal parts of heavy fuel oil (20"

Jan 1, 1956

By W. E. Bonini, E. A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey' for the purpose of de-lineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Pas-saic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum. In 1939 and 1946 the East Orange Water Dept. had electrical-resistivity surveys made to determine depths to bedrock. From the resistivity data the exploration company prepared a bedrock contour map. A well field expansion program begun in 1955 utilized this information to locate sites for test wells along a predicted northward extension of the buried valley in which existing production wells are located. After several test wells (wells 201-205) had been drilled, it became apparent that the resistivity information was unreliable." For example, test well 201 recorded bedrock at a depth of 72 ft, whereas the resistivity depth determination was 130 ft. As a consequence, the test drilling program was temporarily suspended and a seismic survey was under- taken to determine the topography and extent of the buried valley known from well records to underlie the existing well field. In the first phase of this study, several seismic shot point locations were placed at sites where well logs had been obtained previously. This procedure is necessary in a new area to determine whether the seismic method is applicable and what degree of accuracy is to be expected. At the East Orange Water Reserve, depths obtained from the shot points near test wells 202, 203, and 204 were within 8 to 11 pct of the depths logged (Table I). With this assurance that accurate results could be obtained, additional seismic spreads were located on the Water Reserve. Using a portable refraction seismograph, in the fall of 1955 a crew of four men shot a total of 29 reversed seismic spreads in a period equivalent to six field days. Charges as heavy as 3 1b of 40 pct dynamite were necessary at a few places to overcome ground vibrations caused by traffic on nearby highways. At most other sites, a 1-1b charge was sufficient. Travel-time plots were made for all spreads, and depths and true velocities were calculated according to formulas for multiple sloping layers by Ewing, Woollard, and Vine.' The plot of spread 7 (Fig. 2) is typical of the short spreads in which bedrock was shallow—about 50 ft in this case. Where there were not enough arrivals through the bedrock to define the high velocity bedrock line, the spreads were lengthened. This was done by placing shots on line several hundred feet away from each end of the line of geophones. It was then possible to construct complete reverse plots for both short and extended shot points (see spread 27, Fig. 3). Four individual depths were calculated from each extended spread. Three and in some cases four seismic layers were observed. The surficial layer had a velocity range of 900 to 1200 fps, the lowest velocity recorded. This seismic layer is above the water table and is interpreted as recent river silt. The bedrock had the highest velocities, which ranged from 10,600 to 16,400 fps. Intermediate velocities ranged from 4500 to 6800 fps. In every case the intermediate layer was within

Jan 1, 1959

By Y. A. Rocher, J. E. Dorn, L. A. Shepard

Creep activation energies for single aluminum crystals favorably oriented for shear by (010) [101] glide were detemined over the temperature range from 78" to 900°K. Observations of slip bands on the specimen surface were made in conjunction with the investigation. From 78" to 780°K, the activation energies obtained in this imestigation agreed closely with those previously found for creep by (111) [101] slip. Between 78" and 140°K, the activation energy was identified with the Peierls process, while between 260°and 780°K the activation energy was close to that for cross-slip. The coarse wavy slip bands nominally parallel to the (010) plane observed above 260°K were attributed to fine cross-slip. From 800" to 900°K, unusually high apparent activation energies ranging from 28,000 to 54,000 cal per mole were obtained. These apparent activation energies were attributed to re crystallization. AS illustrated in Fig. 1, a recent investigation1 has shown that creep of aluminum single crystals by the (111) [i01] mechanism is controlled by three unique processes, each of which is characterized by a single activation energy which is independent of the applied stress and the creep strain. A comparison of the observed activation energies with theoretically calculated values permits a fairly clear identification of the three operative creep processes. Below 450°K, where the activation energy for creep is 3,400 cal per mole, the deformation is controlled by the Peierls process, the activation energy for creep agreeing well with that calculated by seeger2 for the energy required to nucleate the motion of a dislocation loop against the atomic forces of the lattice. Between 590° and 750°K, the observed activation energy for creep of about 28,000 cal per mole agrees well with the energy necessary to induce cross-slip. Seeger and schoeck3 estimate that the activation energy is about 24,000 cal per mole whereas Friedel4 recently calculated this activation energy to be 28,000 cal per mole. Above 800°K the activation energy of 35,500 cal per mole that was observed for creep agrees well with that estimated for self-diffusion in aluminum.= In this range the operative rate-controlling slip process has been clearly identified as that arising from the climb of edge dislocations. The objective of this investigation is to ascertain whether a single crystal of aluminum favorably oriented for simple shear in the [loll direction on the (010) plane might exhibit uniquely different activation energies for creep from those obtained previously for (111) [101] slip. Whereas the exis- tence of such unique activation energies would constitute incontrover table evidence for new mechanisms of slip, the absence of any new activation energies might suggest that slip of aluminum is confined to the (111) [loll mechanism. Several factors prompted the selection of the (010) [101] orientation for study. First, there are more reported observations of (010) [loll slip than of any other nonoctahe-dral mechanism.8-10Secondly, Chalmers and Martius1l have concluded from considerations of the energies of dislocations that (010) slip is the second most favored mechanism in face-centered-cubic metals. Finally, favorable orientations for simple shear by the (010) [loll mechanism provide the least favored orientation for slip by the (111) [101] mechanism. EXPE-RIMENTAL PRO-CEDURE The high-purity aluminum stock, specimen preparation, shear fixture, extensometry, and experimental technique used in this investigation were the same as those previously reported.' Single-crystal spheres grown from the melt of 99.995 pct pure Al* were _ *The high-purity aluminum used in this investigation was graciously given by the Aluminum Company of America. oriented, carefully machined into dumbbell-shaped shear specimens, annealed, and chemically polished. The finished specimen had a central reduced section 0.190 in. wide and 0.590 in. in diam and 1/4-in. grip sections at both sides, 0.690 in. in diameter. The specimen was oriented in the stainless steel grips of the shear fixture with the (010) plane perpendicular to the dumbbell axis and the [loll direction parallel to the stress axis within 2 deg. Creep activation energies were calculated in the previously described manner1 from determinations of the instantaneous change in shear strain rate produced by an abrupt 15 to 20 deg increase or decrease in test temperature. If is the instantaneous strain rate at strain y and temperature T1, and ?2 the instantaneous rate at y and T2,

Jan 1, 1960

By Hoyt Gale

RECENT work on borate deposits near Kramer, in the extreme southeast corner of Kern County, California, is of special interest to those who are making a study of the mode of origin of the borate minerals colemanite and ulexite. A valuable clue to the mode of origin of colemanite in its present known deposits is given in a paper by W. F. Foshag1, of the United States National Museum. Colemanite is found in or near original deposits of ulexite, from which it is supposed to have been derived by a change in the rate of movement or the character of the ground water. Indications that an alteration of this sort had produced colemanite were first recognized by the writer' in specimens collected in the Kramer district in 1920, and sent to W. T. Schaller, at U. S. Geological Survey, for identification. The identity of the two borate minerals in these specimens was not at once determined, but the relations of the minerals as seen in the specimens afforded a manifest clue to the origin of the deposits. Similar specimens were obtained by the writer from deposits in death Valley soon after he had examined the deposits near Kramer. After studying the specimens submitted to him Dr. Schaller wrote as follows: "I have finally positively identified the boron minerals you sent me with your letter of Sept. 27. The `white fibrous mineral like ulexite' is ulexite; the harder nodules' in the clay are colemanite, apparently formed from the ulexite as a result of leaching, with recrystallization in place-a theory that Foshag is working on." The present paper is a report on the facts observed at. the deposits near Kramer, and some general observations on the geological relations noted, which, unfortunately, still form only a very incomplete record.

Jan 2, 1926

By N. J. Grant, B. C. Giessen, Paul Predecki

ALLOYS of gold, silver, and aluminum with elements of the groups BII, BIII, BIV, and BV were prepared by a rapid quenching technique (splat) and were examined by X-ray diffraction. Five new intermediate phases were found and will be described briefly herein. For the gold and silver systems, the concentration ranges having an electron/atom ratio e/a of 1.4 to 1.5 ("3/2 Hume-Rothery phases") were studied primarily. Master alloys were prepared from high-purity metals (99.9+ pct or better) by melting either in evacuated fused silica capsules or by nonconsum-able-electrode arc melting in an argon atmosphere. Small pieces, 20 to 50 mg, of each alloy were blast-atomized to form a splat, by a technique similar to that described by Duwez and Willens.1 The technique used for this study is described in detail in Ref. 2; it utilizes a resistance-heated graphite crucible with a small hole at the bottom, directed toward a metal substrate or quenching plate. The prepared alloy rests over the fine hole, through which it is expelled by an explosion shock wave in the form of fine droplets (1 to 50 µ) of molten metal onto a copper or silver substrate, which is maintained at about -190°C. The resulting very high cooling rates (see Ref. 2 for quantitative measurements) can prevent the process of nuclea-tion and growth in many instances, resulting in the formation of metastable phases. The splat particles were transferred to a GE-XRD5 diffractometer and maintained at -190°C, where they were examined with CuKa radiation. The samples were then allowed to warm to room temperature or were heated to higher temperatures until the equilibrium structures formed. Of fifteen alloy systems considered, nonequi-librium structures were encountered in six; these are described below and summarized in Table I. In the system Au-Sb a metastable £ phase (A3 type, hcp, a = 2.898 + 0.002A; c = 4.731 * 0.004A; c/a = 1.633) was found in the concentration range Au + 13 to 15 at. pct Sb. This phase is isomorphous with the stable phases in the systems Au-Cd, Au-In, and Au-Sn, all at an average e/a ratio of 1.4 to 1.5. The concentration range of one-phase metastable was deduced from the small amounts of supersaturated gold solid-solution phase present in the splat product. It was found that ? could also be retained by splatting onto a substrate held at room temperature: however, decomposed into the equilibrium phases Au + AuSb2 after heating to 200°C for 1/2 hr, or on holding the powdered splatted alloy at 20°C for several months. Calorimetric measurements will be made in an attempt to decide the question whether ? is metastable at all temperatures or whether it is a stable phase at low temperatures. There is evidence that another phase, possibly also close-packed but with a different stacking sequence, can be obtained by rapid quenching of alloys with a different antimony content. Klement, Willens, and Duwez3 reported the existence of an amorphous phase on quenching Au-Si alloys (25 at. pct Si) to - 196°C. They found that on heating to room temperature another phase of unknown crystal structure was formed. This was confirmed (see Table I); however, the new crystalline phase, designated as ?, could also be formed simply by rapid quenching to room temperature, and even was found to exist already in the as-cast Au + 20 at. pct Si alloy. It was found that ? decomposed into Au + Si on the specimen surface at room temperature. This behavior, and the question whether or not there is an equilibrium-temperature region for ?, have not yet been resolved. It is probable that ? (Au + 20 to 21 at. pct Si) is cubic of the -brass type (D81-3) with a = 9.60, + 0.01A and N = 52 atoms per cell [compare 6 (CU-Sn)4]. Except for two very weak lines, the powder pattern of about thirty lines could be indexed on this basis; however, a determination of the atom positions has not yet been attempted. For Au-Ge the C phase was observed at about 21 at. pct Ge as reported by Luo et at.5 Lattice parameters a = 2.876A, c = 4.73,A, c/a = 1.64 were found. In the Au-Pb system, formation of a ? phase was not observed, but in the lead-rich region at 75 at. pct Pb, broad peaks belonging to an amorphous phase were found. The maximum diffracted intensity occurred at 28 = 32.4 deg which is about 1 deg larger than the position of the (111) line of lead (Cuka). For Ag-Pb, an amorphous phase analogous to the one found in the Au-Pb system was observed; this metastable phase exists probably at about 75 at. pct Pb. Since no lead-rich alloys were tested, all alloys consisted of silver + amorphous phase at -190°C. In A1-Ge alloys, line-rich and complex powder patterns were obtained at about 30 at. pct Ge; they bear similarities to those of aluminum and germanium, but are of lower symmetry; the existence of more than one intermediate phase is possible. The authors are grateful to the Kennecott Copper Corp. for Fellowship support, and ARPA (Contract

Jan 1, 1965

By Peter M. Fozzard

The San Bartolomt silver deposit was discovered by a United Nations team of geologists working with a counter- part team of staff of the Ecuadorian Government's General Directorate of Geology and Mines (DGGM). The Phase I project over five areas of operation during which this discovery was made was financed through a United Nations Development Program contribution of $860,000 and an Ecuadorian Government participation of about $680,000 equivalent. Existence of mineralization at San Bartolomé was first recognized in 1966 when a reconnaissance geochemical stream-sediment program was carried out over a 10 500 km2 (4,054 sq mile) area centered around the city of Cuenca in southern Ecuador. Over the course of this project more than 10,000 samples of stream-sediment, soil, and rock materials were collected. Average costs per sample were $10.00, as follows: collection, $5; sample preparation, $1.60; assay work, $3.40. Initially in the program (1965-1966) sediments were collected along all motorable roads and tracks. Routine analyses, originally by colorimetry and later by AAS, were for Cu, Pb, Zn and occasionally As, Ni, and Co. Discovery geochemical samples from the San Bartolomé drainage area were among the first to be taken in 1965. As luck would have it, the road along which this traverse was taken passes only some 100 m (328 ft) downstream from the mineralized suboutcrop. The relevant two streams sampled are of inconsequential size, some 1 m (3.3 ft) in width, with a limited flow volume throughout the year. Original anomalies were recognized through cold-extractable Cu/Zn analyses. The pH of all river waters was also recorded at sample sites. Resampling the discovery sediments when AAS became available showed total extractable values of between 150 ppm-300 ppm Zn, 550 ppm Pb, and 10 ppm Ag. In 1967 the first followup was by rough-and-ready means. Dithizone field-kits (THM) were used to rapidly test soils from the surrounding area. The area has no outcrop. This work allowed the definition of an area of interest of some 2 km (1.2 miles) x 500 m (1640 ft). Six approximately 1 km (0.6 mile) to 1.5 km (0.9 miles) lines spaced at approximate 250 m (820 ft) intervals were established and used for IP surveys and soil sampling at 50 m (164 ft) intervals. Where one of the lines crossed the westernmost geochemical discovery creek a first-priority geophysical anomaly coincided with a major Zn/Pb (and later Ag) soil anomaly. A pit was sunk and encountered mineralized vein material at a depth of 1.5 m (5 ft). This lucky glory hole confirmed the geochemical discovery and prompted systematic followup. Immediately, costeaning of the west bank of the discovery creek, the Quebrada Ocashuaico, was carried out and exposed weathered and leached mineralization. Nearly 100 mineralized veinlets ranging in thickness from 0.5 cm (0.2 in.) to 8 cm (3 in.) were exposed across the 180 m (59 1 ft) costean. Sixty mineralized veinlets were determined over a 90 m (295 ft) wide zone. Sampling delineated minable widths averaging between 0.16 and 0.31 kg/t (5 and 10 oz per st) Ag with associated copper (very sporadic) lead and zinc. Over the period 1968- 1972 a considerable amount of detailed work was completed: detailed IP, EM Turam, magnetic and mise-a-la-masse geophysics, very detailed soil- sampling, trenching, drilling and glory-hole drifting, and cross-cutting. Numerous problems were encountered: the area was found to be a most difficult geoelectrical target; zero outcrop; pyrite (nonargentiferous zones) associated with faulting; mineralized groundwater; extensive clay development; loss of diamond drill-core, and no two-dimensional surface information. As the program developed the complexity of the structure was slowly unravelled, using a degree of good guesswork. Apart from photogeological and ground geological mapping at various scales, the following

Jan 1, 1985

Oct. 8 to 13, inclusive, 1917 COMMITTEES Committee on Arrangements H. A. BUEHLER, Chairman W. E. MCCOURT, Secretary C. J. ADAM L. L. HUTCHISON VICTOR RAKOWSKY J. A. CASELTON EUGENE MCAULIFFE J. D. ROBERTSON .F. W. DEWOLF P. N. MOORE ARTHUR THACHER E. F. GOLTRA MRS. P. N. MOORE H. A. WHEELER Committee on Ladies', Entertainment MRS. PHILIP N. MOORE, Chairman MRS.. W. E. MCCOURT, Vice-Chairman MRS. D. M. ARMISTEAD MRS. R. G. HALL MRS. A. A. BONSACK . MRS. J. W. HEGELER MRS. B. F. BUSH MRS. J. N. HOUSER MRS. G. 0. CARPENTER MRS. EUGENE MCAULIFFE MRS. F. V. DESLOGE MRS. RUDOLPH PORTER MRS. F. W. DEWOLF MRS. N. P. ROOD MRS. A. W. DICKINSON MRS. ARTHUR THACHER

Jan 12, 1917

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to bene-ficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation. Earliest surveys of the formations were conducted to outline the parts that could be concentrated at % in. (3 mesh). Operators agreed on this size because anything finer required sintering or other agglomeration processes. At 3 mesh only the structural features, as defined above, would be liberated. With suitable ores concentration was easy, as any of the gravity methods could be used. Sink-and-float gave good results, but with this method only limited portions of the iron formations yielded a desilrable product.1,2 n general, the iroa content could be raised to shipping grade, but the silica content remained too high—sometimes 20 pct—instead of 9 or 10 pct. Grinding did not greatly increase the liberation ofsilica until 2010 mesh or finer was reached. To find the reason fpr this T. M. Broderick began micros~opic examin'ations of the formations in 1933.3 Procedure: The purpose of this discussion is to correlate the appearance of typical portions of the iron formations with their amenability to concentration. As liberation is essential before separation becomes possible, much of the work is based on measuring the liberation achieved by crushing and grinding. Both heavy media and magnetic tube tests were used in this work. On the basis of general structural features such as banding, degree of alteration, and leaching, a specimen was selected from each part of the iron formations studied. The specimen represents the gross features of the formation and not necessarily the particular formation quantitatively. One half of the specimen was polished for macro-study, and the remainder was used for analyses to obtain the grades represented by variations appearing in the macrosection. Specimens for microscopic examination were also prepared for each variation in gross appearance. For correlation of microstructure with liberation, the previous work by sink-and-float methods was supplemented by magnetizing roasting followed by magnetic separation. The results show the liberation of silica to be very important at the sizes used, because any silica particle with iron minerals occluded would be held in the concentrate. A magnetizing roast changes the crushing and grinding character of the sample. For partly leached soft samples the change is slight, but with harder types and those in which there is a considerable change in crystal structure of the minerals, the increase in liberation of the iron minerals may be 30 pct more than that of unroasted samples at the same crusheH size. Gogebic Range Iron Formations: The Gogebic Iron Range is located in the extreme western and southern parts of Michigan's Upper Peninsula, extending westward into Wisconsin. Samples for this study were obtained from the Ironwood formation, comprising three chief members—the Plymouth, Norrie, and Ahvil—with several intermediate slates and thick overlying slates. (The slates are not considered in this discussion because grinding finer than present practice is usually required to liberate the iron minerals.) The predominant iron mineral is hematite, about half of which is hydrated to goe-thite. Limonite occurs in some of the partly leached areas, and siderite in parts of the formation.

Jan 1, 1958

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By Donald L. Katz, Marshall B. Standing

Density data are reported on 16 saturated hydrocarbon vapors at Pressures ranging from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. Introduction The densities of natural gases are necessary in many engineering in in petroleum production and utilization, Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 Ib. per sq. in.4 Recent discoveries of pools having Pressures UP to 7500 lb. Per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data On gas density at high pressures. Methods of Computation The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The meth-me-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most- of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir Or while on contact with liquid &apos;&apos;&apos;ring flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those consider. ably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions, This paper reports the density of I6 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure&apos; have been modified and enlarged. A simpli-fied method of obtaining gas density is presented in the Form of charts, which apply for specific groups of gases.

Jan 1, 1942

By Marshall B. Standing, Donald L. Katz

Density data are reported on 16 saturated hydrocarbon vapors at Pressures ranging from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. Introduction The densities of natural gases are necessary in many engineering in in petroleum production and utilization, Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 Ib. per sq. in.4 Recent discoveries of pools having Pressures UP to 7500 lb. Per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data On gas density at high pressures. Methods of Computation The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The meth-me-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most- of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir Or while on contact with liquid &apos;&apos;&apos;ring flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those consider. ably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions, This paper reports the density of I6 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure&apos; have been modified and enlarged. A simpli-fied method of obtaining gas density is presented in the Form of charts, which apply for specific groups of gases.

Jan 1, 1942

By Dilip K. Paul, Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world, primarily because of oil and gas accumulations on their flanks, and to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. Thus a salt dome can be expected to act as a conduit bringing heat vertically from deep within the earth&apos;s crust.

Jan 5, 1974

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as &apos;la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10&apos;5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By T. R. Ingraham

The thermal decomposition of cupric sulfate and of cupric oxysulfate has been examined by deter-mining the equilibrium gas pressure generated over each pure compound. The equilibrium data have been used to calculate the thermodynamic properties of both compounds, and the results have been combined with previously published data to establish a predominance-volume diagram for the Cu-S-O system over the normal range of roasting temperature and gas composition used in the treatment of copper minerals. Copper oxysulfate recrystal-lizes at 1100°K with an apparently irreversible en-dothermic heat requirement of 2.9 * 0.3 kcal per mole. WHEN mixed sulfide minerals containing copper are roasted, either of two procedures may be followed, depending on the nature of the other metals. In the first procedure, the roasting is controlled to produce a maximum amount of water-soluble copper sulfate which may be removed selectively from the water-insoluble compounds of the other metals. In the second, control is directed toward the production of water-soluble sulfates of the other metals and an insoluble salt of copper. Effective control of either of these processes would be enhanced by knowledge of the thermal stability of cupric sulfate and of cupric oxysulfate. In this paper, established data for the thermal stability of cuprous and cupric sulfide and of cuprous and cupric oxide will be combined with new data for the therma1 stability of cupric sulfate and cupric oxysulfate, to designate the volumes of stability of the significant compounds in the Cu-S-O system in the temperature range 750° to 950°K. EXPERIMENTAL Materials, Apparatus, and Procedure. The copper source material used in all experiments was Fisher Certified Reagent Grade "anhydrous" cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared from the normal sulfate by two procedures. In the first, equimolar quantities of cupric oxide (prepared by decomposition of the sulfate) and cupric sulfate were ground together and heated under vacuum in a sealed silica vessel at 800°C. This procedure was subject to failure because of explosion of the silica vessels due to the pressure of the final traces of water released from the sulfate on the initiation of its decomposition. The second procedure involved roasting the cupric sulfate, with frequent rabbling, in a muffle furnace at 725°C for a period of 48 hr. This produced an excellent product, which was confirmed as copper oxysulfate by X-ray and chemical analyses. The experimental technique used was that of measuring the total pressure exerted by the sulfur trioxide, sulfur dioxide, and oxygen produced by the following reactions: 2 CuS04 = cuo • CuSO4 + SO3 [1] cuo . CuSO4 = 2 cuo + SO3 [2] SO3= SO2 + 1/2 O2 [3] The apparatus used in the experiments has been described previously.1-3 Its main feature of a U-tube mercury manometer in which the mercury is protected from corrosion by enclosure in a flexible Pyrex bellows. Before beginning a run, the interior of the apparatus, including the bellows-manometer and all connecting tubing, was thoroughly washed with hydrochloric acid and distilled water to remove any

Jan 1, 1965