Search Documents

By Kent E. McElhattan

Selecting efficient machinery for an underground mining operation is a highly skilled art that still depends largely on human judgment and experience. In a coal mine, for example, there is no better way to predict the results of operating with a cutting machine or a continuous miner than to go underground with a sharp-pointed miner's pick. The trained eye can detect the depth of point penetration, cleavage planes, roof and floor strata, and many other conditions impossible to determine in a laboratory. Even so, however, an entirely new set of conditions may lie unexposed just a few feet behind the solid face. The candid truth of the matter is that practically nothing is known of the phenomenon of extracting a mineral from a solid. Consequently, the selection of mineral extraction machinery and systems must be based on results obtained elsewhere under apparently similar conditions. A recent study of the problem of equipment and system analysis was conducted in the coal mining regions of West Virginia. This state was chosen for study because it afforded representative sampling. The 172 coal mines investigated ecompassed seam heights ranging from less than 30 in. to over 84 in. and covered virtually all known coal mining conditions except two. The exceptions are the extreme pitch of coal seams in the western United States and British Columbia and the "bumps" encountered in the Rocky Mountains. Both of these extreme conditions are worthy of individual study.

Jan 7, 1969

By Philip Lindstrom

T he Radon mine is in the north end of the Big Indian mining district in San Juan County, Utah. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual pre¬miums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining.

Jan 12, 1964

By Zay, Jeffries

THE effect of thoria (ThO2) on grain growth in tungsten was discussed in some detail in a paper presented before this Institute by one, of the authors in 1918.1 In that paper it " was assumed that the, thoria was present in the tungsten entirely as a mechanical mixture. There was no indication in the experiments described that even a trace of the thoria was in solid solution in the tungsten. Langmuir,2 however, observed that thoriated-tungsten filaments under certain conditions showed electron emissions many thousand times greater than unthoriated tungsten at the same temperature. He concluded from his studies that a slight amount of the thoria had dissociated on heating the filament to a temperature near 220°. C. At this temperature and higher, part of the thorium diffuses to the surface of the filament where it evaporates at. a much faster rate relatively, than the tungsten, and also at a rate, nearly as fast as it is brought to the surface by diffusion: If the temperature is lowered to say 1800°,. C., diffusion of the thorium atoms to the surface is more rapid than evaporation, sown adsorbed film of thorium atoms is produced on the surface of the tungsten filament. The electron emission is governed by the outside layer of atoms so the emission from such a filament might be expected to approxi¬mate that of a thorium filament at the same temperature. PRESENCE OF METALLIC THORIUM IN THORIATED TUNGSTEN If the filament containing the adsorbed film of thorium. is heated to a sufficiently high temperature, the thorium atoms evaporate: rapidly and the electron emission becomes more nearly that of tungsten. On cooling again to 1800° C., or thereabouts, the emission 'builds up gradually to a maximum. The filament containing the adsorbed layer of thorium atoms is said to be "activated." By studying the rates of activation under different conditions of prior thermal treatment and at different temperatures, Langmuir was able to arrive at an estimate of the

Jan 1, 1927

By M. G. Taverner

Research was conducted into cold briquetting dross arisings and metallurgical coke fines from an Imperial Smelting Furnace (I.S.F.) as an economic means of agglomerating fine materials for smelting in a blast furnace. A mechanism was postulated whereby strong bonds were developed within the briquettes; laboratory scale smelting trials and full scale plant trials are included in the paper with a description of a two tonne/hour briquetting pilot plant. Benefits from smelting briquettes in an I.S.F. were measured directly in metallurgical coke savings and, indirectly, by a significant improvement in sinter plant productivity.

Jan 1, 1977

By Thomas Read

IN speaking of immaterial problems of industry I am using the word immaterial in its original sense, not consisting of matter; not in its derived sense, unimportant. There is nothing of a paradox in saying that immaterial problems are the most important in human life, for His a matter of everyday observation that much of the news in the daily papers, and most of the world's best literature and drama, deal with human conduct that has for its motive forces that are but little concerned with material things. The engineer's preoccupation with physical forces, in extending his control over them, has not blinded him to the impor-tance of forces that, for want of a better word, I call immaterial; but he has considered that dealing with the one is his job and the other is not. All the evidence of the past decade indicates that the latter are so in-extricably interwoven with the former in modern in-dustrial life that the engineer will have to concern himself with them whether he wants to or not. Some of the most important of the problems arising from the action of these forces relate to the mental hygiene of the workers in industry. Mental hygiene in industry was concisely defined, in terms of the best present knowledge, by Dr. C. Macfie Campbell, speaking last April before the executive com-mittee of the Associated Industries of Massachusetts, and as his statement can scarcely be bettered, I quote it below: "The term mental hygiene is apt to appear vague. The actual stuff with which mental hygiene deals may be briefly reviewed.

Jan 9, 1927

CHAIRMAN (J . E. JOHNSON, J R., New York, N. Y.).-It may be n matter of some interest that sodium cyanide is now being made commercially by melting together in an electric furnace calcium cyanide with a common salt, which produces calcium chloride and sodium cyanide. It seems to me entirely possible that you have here about the same results that would be obtained by melting calcium chloride and ordinary cyanide together, only you obtain it a good deal cheaper. There is no doubt about that reaction once it is being carried on on a large industrial scale for the manufacture of cyanide for other uses. I think probably the same, thing takes place here, with the possible exception of lowering the melting point due to the presence of the calcium chloride.

Jan 5, 1919

By H. H. Rachford, D. S. Howard

In the withdrawal of fluids from tilted aquifers it is of value to be able to predict pressure patterns during the course of the pressure decline. As an example of this, in the displacement of fluids from oil reservoirs being produced by water-drive, prediction of the reservoir pressure is an important factor in fixing production rate. The prediction of pressure patterns in the depletion of an inclined aquifer has conventionally been made by solving the well known flow equations for the pressure Patterns in a horizontal aquifer, and correcting these patterm for the pressure difference due to the hydrostatic head associated with the vertical distance between a point in the horizontal aquifer and the corresponding point in the tilted aquifer. Inasmuch as the equation describing flow in tilted strata is different from that for horizontal flow. there was question as to the validity of the simple corrective procedure current1y in use. To examine the magnitude of error made using this procedure, an inclined aquifer was chosen for which the error was expected to he large, and the equation for flow in this tilted stratum was solved numerically. The results of the conventional procedure of correcting the solution of the equation for horizontal flow was compared with the solution of the correct equation by studying the difference between predicted pressures by the two methods. Three forms of the hydrostatic head correction were studied. The results for all three forms of the head correction are similar. The error in the approximate solution is quite dependent on the position of the horizontal aquifer with respect to the inclined one. The error is greatest at the producing end ad increases with amount of fluid withdrawn. The magnitude of the errors is not large if a good choice is made for the position of the horizontal datum. The most satisfactory position for the datum in all cases is near or slightly about the mid-point of the inclined stratum. Use of the best approximate method studied with the best datum tested yielded predicted pressures in error no greater than 7 psi. INTRODUCTION The movement of water by expansion from an aquifer to displace fluids from a contiguous oil reservoir was first recognized over 20 years ago.9 Since that time much work has been done to relate this mechanism to reservoir behavior mathematically. The result of this effort on the part of many workers has led to an understanding of underground fluid movement which has enabled us to follow and predict the behavior of the water-drive reservoir. One reason that good progress has been made in the application of mathematics to the study of pressure patterns and water movements in aquifers has been that the differential equation which describes this process is of a relatively simple form. The equation for the isothermal, horizontal, viscous flow of water through homogeneous sandstone is identical with that for the diffusion of heat through homogeneous solids, and this equation and means of obtaining solutions for it with many types of boundary conditions have been studied extensively. That this work has been highly successful is clearly emphasized by the large number of solutions developed for problems of interest both by methods of formal mathemat-

Jan 1, 1957

By Frederick Vickery

THE discovery of oil on the Goleta anticline has extended the petroliferous areas of California 18 miles west of the previous limit at Summerland and 35 miles south of the fields at Santa Maria. In each of these localities the oil is found in the Miocene-Pliocene strata, but as the oil at Goleta is found in the Sespe formation, which is generally considered as Oligocene or lowermost Miocene, the Goleta field extends the production of that horizon 52 miles west of South Mountain, the previous western outpost. Two horizons of high-gravity, paraffin-base oil have been found at shallow depths, and the exploratory well, Goleta No. 1, is now being drilled to test the productivity of an expected horizon in the Meganos formation. The Goleta structure is 12 miles west of the city of Santa Barbara and 2 miles north of the coast. Although it is within part of the old Spanish Rancho, Los Pueblos, it corresponds to T. 4 N., R. 29 W., S. B. B. and M., Santa Barbara county, California. The discovery well, Goleta No. 1 was drilled by the Miley Petroleum Ex-ploration Co. on the Tecolote ranch in the part of the Spanish grant corresponding to the sw. 1/4 of the nw. 1/4 of Section 3. Despite the apparent isolated position of the Goleta field, it is within the Ventura basin. The idea that the Ventura basin terminates at the ocean beach near the city of Ventura is neither sup-ported by the geologic structures nor the sequence of strata west of that city. This basin at the present time is known on the land as the Santa Clara valley and beneath the sea as the Santa Barbara channel. It extends westward to Point Concepcion. The Ventura basin, before the Miocene and Pliocene epochs of deformation, was much broader than at the present time. It is bounded by two lines of uplift, the Santa Ynez range on the north and the Santa Monica mountains with their extension, the Channel islands, on the south. Both of these ranges trend east and west. The Ventura basin and the mountains that bound it are part of a remark-able east-west orogenic unit, which interrupts the pre-vailingly northwest ranges along the Pacific Coast.

Jan 10, 1927

By Robert M. Jimeson, James M. Grout

The competitive market potential for solvent-refined coal is estimated and the market advantages are enumerated. Markets are possible in combustion, railroad locomotion, and carbon electrodes. The combustion characteristics are consistent with expected air pollution restrictions on the emission of sulfur and particulate matter. A market potential of sufficient size exists to support the initiation of solvent refining in the United States. The market analysis should help fuel producers determine the advisability of their undertaking solvent refining of coal.

Jan 1, 1972

By M. T. Hepworth, A. K. Stewart

Iron containing 0.1 pct A1 and -0.9 pct P by weight was internally oxidized in the temperature range 900° to 1300° C, where the bcc structure is stabilized by phosphorous. By measuring the depth of penetration of oxygen with time in an internally oxidized zone for an imposed surface oxygen potential, oxygen permeability was determined. The dgfusion coefficient of oxygen in iron was then calculated using known solubility data, yielding the expression: where Do is the diffusion coefficient of oxygen in bcc iron in sq cm per sec and T is temperature in OK. RECENTLY Hepworth, Smith, and Turkdoganl measured the diffusivity of oxygen in bcc iron and reported the temperature dependence of diffusivity from data determined in the a, and 6 temperature ranges. Subsequently Swisher and Turkdogan' have measured the diffusivity of oxygen in fcc iron. Internal oxidation techniques were employed by these investigators and in this current study. The analysis of this technique is developed by wagner3 (presented in English by Hauffe4 and Rapp 5). In this present study bcc iron stabilized by phosphorous was used to determine oxygen diffusivity in the temperature range 900° to 1300°C. Meijerin 6 has studied oxygen permeability in this temperature range using bcc iron stabilized with 5 pct Sn. Other inves- tigators who have studied oxygen permeability in bcc iron at other temperatures are Schenck et al., 7 Bohen-kamp and Engell, 8 and Bradford. EXPERIMENTAL Electrolytic iron of 99.99 pct purity was alloyed to contain 0.897 pct P and 0.093 pct Al. The maximum weight percent phosphorous required to stabilize bcc iron between 910" and 1392°C is 0.51 pct as determined by Haughton,10 0.42 pct by Roquet and jegaden," and 0.58 pct by vogel,12 with the latter value preferred by Hansen.13 Microprobe analysis indicated that there was no segregation of the phosphorous either before or after permeability studies; therefore, the quantity of phosphorous added was assumed to be sufficient to stabilize the bcc structure. Furthermore, the permeability results of studies on this alloy agreed substantially with interpolated values from previous data on bcc iron.' An ingot of the Fe-P-A1 alloy was hot-rolled to a l-in.-thick slab. Specimens were machined to dimensions: 13/8 by $ by 1/4 in. The experimental apparatus and procedure used have been described before.' A constant oxygen potential was established by passing argon and hydrogen through a column of oxalic acid dihydrate, which has a water vapor pressure which is well-known as a function of temperature. Slab specimens were exposed to a gas mixture sufficiently lean in oxygen to prevent the formation of a surface oxide for predetermined temperature for selected times. The specimens were then quenched, sectioned, and examined metallo-graphically. All quenched specimens were iron-plated to provide protection from the outside sample edge during polishing. Fig. 1 shows a typical microstruc-ture for a specimen oxidized at 953°C for 48.00 hr at a water vapor-to-hydrogen pressure ratio of 0.20. DISCUSSION AND RESULTS The following equation was derived by Hepworth et al.' from Wagner's kinetic expressions for internal oxidation:

Jan 1, 1969

By J. J. Taber, W. K. Meyer

Experiments on consolidated sandstones have shown that a variety of conditions are responsible for the wide range of behavior observed when oil and water are displaced simultaneously by a solvent which is miscible with both. The type of displacement is influenced most strongly by the relation between the plait point of the ternary phase diagram and the composition path followed by the system as it achieves mis-cibility. Neglecting viscosity, the displacement becomes less efficient as the distance between the composition path and plait point is increased in either direction so that a very wide spectrum of displacements is possible with different alcohol, oil and brine systems. It is possible by choosing various composition paths as miscibility is achieved to exercise some control over the actual displacement mechanism. Control over the composition path is exercised by adding oil or water in specific amounts to the alcohol prior to its injection into the porous medium. This technique apparently makes it possible to obtain piston-like displacements with systems which are usually characterized by the efficient displacement of only one of the two phases i.e., either oil or water, while the other phase lags behind. However, the simultaneous displacement of oil and water is not as efficient as other miscible displacements at a similar mobility ratio. The evidence indicates that both oil and water "leak" into the alcohol "piston" in compensating amounts. With oils of low viscosities the displacement is inefficient because the low oil saturation in the stabilized bank causes oil to be trapped by water before miscibility is attained. INTRODUCTION The simultaneous displacement of oil and water by solvents such as alcohol has been investigated in the laboratory and in the field. The laboratorv workers investigating all-liquid miscible systems have recognized the great importance that the nature of the traingular phase diagram exerts on the efficiency of the miscible displacement. Gatlin and Slobod pointed out that displacement efficiency will be improved if miscibility can be retained for long periods and that this behavior tends to be followed if the applicable phase diagrams have very low binodal curves. In their unconsolidated sand tests the alcohol was considered an ideal miscible piston displacing both oil and water phases. Later workers have pointed out that an important feature of the phase diagram as far as oil recovery is concerned is the location of the plait point. This is particularly true in the case of consolidated Sandstone.3 Since the original discussion of this effect, the importance of plait-point location has been confirmed and discussed by other author The early workers394 recognized that the position of the plait point could be altered by changing the oil or the alcohol used in an experiment. In addition, recent work has demonstrated that the plait point can be shifted by altering the nature and concentration of dissolved salts in the aqueous phase. However, the entire scope of the relationship between displacement and plait point has not been discussed previously and a technique for changing the composition path as miscibility is achieved in a particular ternary system, i.e., oil, water and solvent, has not been demonstrated. * The importance of oil viscosity on the efficiency of oil displacement by alcohol has not previously been observed, probably because the range of viscosities used in earlier experiments was too restricted. It is the object of this paper to describe the relationships between the ternary phase diagram, fluid properties and the displacement achieved. A technique for controlling the nature of the displacement is also presented. THEORY AND DEFINITIONS PISTON-LIKE THEORY The theory of alcohol flooding has been discussed in some detail.2-4 The concept was advanced that

Jan 1, 1965

By A. Paul Bond

Two series of 17pct Cr iron-base alloys with small, controlled amounts of carbon and nitrogen were vacuum-melted in an effort to detertmine the meclz-uniswls of inter granulur corrosion in ferritic stain-less steels. An alloy containing 0.0095 pct N aid 0.002 pct C was very resistant to intergranular corrosion, even after sensitizing heat treatments at 1700" to 2100o F. However, alloys containing more than 0.022 pct Ni and more than 0.012 pct C were quite susceptible to intergranular corrosion after sensitizing heat treatments at temperatures higher than 1700°F. This corrosion was observed after the usual exposure tests and after potentiostatic polarization tests. Electronmicroscopic examination of the alloys susceptible to intergranular corvosion revealed a small grain boundary precipitate; this precipitate was absent in the alloys not susceptible to such corrosion. Thc electronmicrographs indicate that intergranu1ar corrosion of ferritic stainless steels is caused by the depletion of chromium in areas adjacent to precipi-tates of chromium carbide or chromium nitride. It also seems likely that the precipitates themselves are attacked at highly oxidizing potentials. Confirma-tion of the proposed mechanisms was obtained in tests on air-melted ferritic stainless steels containing titanium. The titanium additions greatly reduced susceptibility to intergranular corrosion at moderately oxidizing potentials but had no beneficial effect at highly oxidizing potentials. A major obstacle to the use of ferritic stainless steel has been their susceptibility to intergranular corrosion after welding or improper heat treatment. It appears that sensitization of ferritic stainless steel occurs under a wider range of conditions than for austenitic steels. In addition, a greater number of environments lead to damaging intergranular corrosion of sensitized ferritic stainless steels than to sensitized austenitic steels. The chromium depletion theory of intergranular corrosion is widely accepted for austenitic stainless steels'" although there: are some objections.3 On the other hand, several alternative mechanisms proposed for ferritic stainless steels include precipitation of easily corroded iron carbides at grain boundaries,' grain boundary precipitates that strain the metal lat-tice,5 and the formation of austenite at the grain bound-arie.6 The application of the chromium depletion theory to ferritic stainless steels has been discussed extensively by Baumel.7 The present investigation was undertaken to determine which of the proposed mechanisms can be sub- A PAUL BOND IS Research Group Leader, Climax Molybdenum Co of Michigan, Ann Arbor, Mich. stantiated with experimental data obtained on ferritic stainless steels. High-purity 17 pct Cr alloys containing small controlled additions of carbon or nitrogen were therefore prepared, and then examined electro-chemically and metallographically. EXPERIMENTAL PROCEDURES Materials. Two series of experimental alloys were prepared from electrolytic iron and low-carbon ferro-chromium using the split-heat technique. In this technique, the base composition is melted, and part of the melt is poured off to produce an ingot. To the balance of the melt, the required addition is made and the next ingot cast. This process is repeated until a series of the desired compositions is cast. By this procedure the impurity levels are essentially constant within each series. All the alloys in the carbon-containing series were melted and cast in vacuum. The base composition in the nitrogen series was melted and cast in vacuum; subsequent ingots in the series were melted with additions of high-nitrogen ferrochromium, and cast under argon at a pressure of 0.5 atmosphere. Two additional alloys were produced starting with normal purity materials. They were induction-melted while protected by an argon blanket and cast in air. Table I gives the composition of the alloys. The 2-in.-diam ingots produced were hot-forged and hot-rolled to a thickness of 0.3 in. and then cold-rolled to 0.15 in. All specimens were annealed at 1450°F for 1 hr. The indicated sensitizing heat treat-s s ments were performed on annealed material. All heat treatments were followed by a water quench. Specimen Preparation. For the 65 pct nitric acid test, 1 by 2 by 0.14-in. specimens were wet-surface ground to remove surface irregularities and polished through 3/0 dry metallographic paper. For the modified Strauss test, $ by 3 by 0.14-in. specinlens were similarly prepared. Immediately prior to testing, the Table I. Compositions of the Alloys Composition, pct Alloy Cr hio C N 270A 16.76 0.0021 0.0095 270B 16.74 0.0025 0.022 270C 16.87 0.0031 0.032 270D 16.71 0.0044 0.057 271A 16.81 0.012 0.0089 27 IB 16.76 0.018 0.0089 271C 16.69 0.027 0.0085 271D 16.81 0.061 0.0O71 4073' 18.45 1.97 0.034 0.045 4075† 18.5 2.0 0.03 0.03

Jan 1, 1970

Jan 1, 1931

By W. C. Hauber

Techniques previously published to predict the production performance of a water flood when the mobility ratio is not unity have been primarily restricted to a five-spot well pattern. When other types of well patterns are considered, the prediction of performance has required either a model study or a complex numerical solution of a multiple-fluid system with a high-speed digital computer. Simple methods are developed in this report for predicting the areal sweep efficiency and injectivity history of a water flood for arbitrary well patterns and mobility ratios. The effect of an initial gas saturation can be incorporated into this method of prediction. With the layer superposition concepts published by Prats, et al.,1 these methods can be used to predict the production performance of a water flood in a reservoir having a wide range in permeability. A reasonably good agreement is shown by comparisons of the results calculated by this method with those obtained either by model studies or by complex numerical solution of multiple-fluid systems. Therefore, it has been concluded that a reasonably accurate method has been developed for predicting the production performance of a water flood employing an arbitrary type of well pattern for any given mobility ratio. A medium-speed digital computer can be used in applying this method. INTRODUCTION Production performance of multi-fluid five-spot water floods can be predicted by the techniques published by Prats, et al.1 This technique takes into account the effects of initial gas saturation, mobility ratio and vertical variations in horizontal permeability. A basic assumption in applying this technique is that unit displacement efficiency does not vary with time after the passage of the flood front. Prats, et al. demonstrated that this assumption is valid for normal waterflood applications with small mobility ratios. To extend Prats' technique to other types of well patterns has required either an experimental model study or a numerical solution of a multiple-fluid system to describe the performance of an individual homogeneous layer. Sheldon and Dougherty2 presented an exact numerical solution employing any arbitrary well pattern. This technique is complex to apply, requiring (1) numerical solution of the single-fluid system, (2) conformal mapping of the streamlines and iso-potential lines to form a new grid network, and (3) a numerical solution of the multi-fluid system on the new grid network. A method was developed in this paper to approximate areal sweep efficiency and injectivity as functions of time for an individual homogeneous layer for arbitrary well patterns and mobility ratios. Analytic expressions were derived to directly apply this method to five-spot and direct line drive well patterns. For other types of well patterns, this method is similar to the approach of Higgids and Leighton,6 in that it utilizes the stream tubes and iso-potential lines obtained by the solution of differential equations when the mobility ratio is unity. However, this method is easier to apply than the Higgins-Leighton method since it does not require knowledge of the variation between oil and water relative permeabilities and saturation. Using the relationship between areal sweep efficiency, injectivity and the volume of water injected into an individual homogeneous layer as obtained by the method presented in this paper, and Prats' technique for the superposition of individual layers, one can predict the production performance of any water flood. ASSUMPTIONS GENERAL Basic assumptions made in this report are that fluids are incompressible and the layers are horizontal, homogeneous and uniformly thick. It is assumed that as water is injected into the layer, three distinct regions are formed —a water bank, an oil bank, and an unflooded region. Each region is assumed to displace other regions in a pis-tonlike manner, with only one fluid flowing in each region, so that there is no change in unit displacement efficiency with time after the flood front has passed in the reservoir. Therefore, the residual oil saturation in the water bank and the oil saturations in the unflooded region are constant throughout the layer. The ratio (F) of the bulk volume of a layer occupied by the oil and water banks at any time before oil breakthrough, to the corresponding bulk volume of a layer occupied by the water bank, is given' by the equation BREAKTHROUGH AREAL SWEEP EFFICIENCY To predict the behavior of any type of waterflood pattern, one must know the breakthrough areal sweep efficiency Eb(Mc,o, F) for the pattern for any water:oil mo-

Jan 1, 1965

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy). Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low grade molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported. In the chlorination process, a gaseous mixture of chlorine and oxygen in the volume ratio bf 2:5 has been passed at 1.66 x 10- 5 m3/s for 1800 s over a 0.01 kg batch of molysulfide concentrate at a temperature of 573°K. Most of the molybdenum has been volatilized as molybdenum oxychloride which has subsequently been extracted in water. The molybdenum value from the aqueous solution has been recovered in the form of calcium molybdate (CaO.MoO3) by treatment with calcium chloride (CaCI2). In an alternative processing scheme, the molybdenum rich solution has been treated with an oxidizing agent (K2S20f.J) and allowed to boil to recover a major portion of the molybdenum value in the form of molybdic oxide (MOOS). The spent charge obtained after molysulfide chlorination has been mixed with about 1 wt % sodium chloride and heated at 773K under an oxygen atmosphere. The reacted mass has been water-leached to yield a nickel-copper bearing solution with limited iron. The process liquor appears to be well suited for further processing by known hydrometallurgical recovery processes for nickel and copper. In the conventional process of molybdenum extraction, the molysulfide concentrate (-59% Mo) is first subjected to roasting to produce molybdic oxide. The oxide is then further processed in sequential steps involving vacuum distillation, ammonia leaching, and calcination to higher purity prior to hydrogen reduction to metal. In India there is at present some small tonnage production of molysulfide concentrate from a byproduct recovery plant of the M/s. Uranium Corp. of India Ltd. (M/s UCIL), Bihar. Efforts are being made at this laboratory to process the low grade fraction of the concentrate which contains sulfides of copper, nickel, and iron; quartz; and chlorites. Here, the conventional routes involving roasting and vacuum distillation appear unsuitable to produce an acceptable quality of molybdic oxide at high recoveries. Formation during roasting molybdates of some of the impurities present in the sulfide concentrate make subsequent vacuum distillation less efficient. In view of these problems, in earlier work reported from this laboratory the low grade concentrate has been processed hydrometallurgically to P. produce calcium molybdate. Starting from this molybdenum intermediate, processes have also been developed for the production of molybdenum and ferromolybdenum. Chlorination as an alternative to roasting for metal sulfides has been drawing considerable interest. The high reactivity of chlorine, the relatively low temperature of operation, the suitability of application to low grade resources, the convenience of recovering sulfur in non-polluting form, and the purity of chlorides which are separated by distillation all favor chlorination. In recent years, considerable work has been reported on the chlorination of common metal sulfides. In the field of molybdenum extraction from its sulfide resource, use of chlorination technology has been rather limited. Senderoff and Labrie3 were the first to chlorinate molysulfide concentrate with elemental chlorine at about 823°K to molybdenum pentachloride for use in the electrolytic preparation of molybdenum. The only other reported work, by Haver, Uchida and Wong, involved reaction between molysulfide and chlorine at 673°K to recover sulfur. The reaction products were, however, identified as molybdenum pentachloride and sulfur monochloride.

Jan 1, 1979

By D. B. Hunter, H. W. Rosenberg

The titanium-rich portion of the Ti-Pd system was investigated from 0 to 75 wt pct Pd by metallo-graphic and X-ray techniques. A 0 eutectoid occurs at 24 wt pct Pd and 1190°F. Two compoutzds are indicated in the region below 75 wt pct Pd, Ti,Pd and Ti2Pd3. The solubility of palladium its a titanium is low, probably less than 1 pct. In 1960 Rudnitskii and Birunl published a complete version of the Ti-Pd phase diagram. However, their work was in disagreement with the earlier literature in that they reported only one inter metallic compound, whereas three had been reported earlier. In view of these discrepancies, it was therefore necessary to redetermine those portions of the diagram of immediate interest. The following account describes our work on the system over the range of 0 to 75 wt pct Pd. MATERIALS AND METHODS Distilled titanium sponge and elemental palladium were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 10 to 50 g blended compacts that were melted into buttons by arc melting under gettered argon on a water-cooled copper hearth. Weighing of the ingredients before and after melting showed that negligible weight changes occurred. Therefore, no analyses were undertaken and the compositions of all alloys are nominal. All alloys were fabricated by hot rolling at 1700°F to 0.070-in.-thick sheet. Scale was removed by sandblasting and pickling in a 5 pct HF-35 pct HNO,, balance H20 solution. For metallographic examination, specimens were mounted after heat treatment transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and then electro-polished using a solution containing 600 ml me-thanol, 60 ml perchloric acid, 360 ml butyl cello-solve, and 2 ml "Solvent X". Unless otherwise specified, etching of alloys containing up to 42 pct Pd was carried out by swabbing with a 12 pct HN03-1 pct HF aqueous etch where a bright etch was required, or by a 1 pct hydrofluoric in saturated oxalic acid solution where contrast between phases was required. The Ti-52.8 Pd alloy was etched with a solution of 25 ml HF, 40 ml glycerine, 35 ml methanol, and 18 g benzalkonium chloride. For X-ray examination, 1/2-in.-square speci- mens of sheet were mounted flat in a standard 1-in. metallographic mount and ground and polished as above. X-ray diffraction was performed using a Norelco type 12045 Diffractometer, employing CuKa radiation with a nickel filter at 40 kv and 20 ma. Specimens were rotated about the sheet normal during exposure. Although this procedure did not remove the effects of sheet texture from the relative intensities, it had the advantage that oxidation or contaminants entering during preparation of powder samples could not confuse the patterns obtained. RESULTS AND DISCUSSION Fig. 1 illustrates the Ti-Pd phase diagram according to Rudnitskii and Birunl with the work of the present authors superimposed. Both interpretations agree that the system is of the 0 -eutectoid type with an extensive 0-phase field, and that the eutectoid temperature is just below 1200°F. There is also agreement that the solubility of palladium in a titanium is restricted. Our work would indicate that the a solubility of palladium is low, probably less than 1 pct. However, whereas Rudnitskii and Birunl place the eutectoid composition at 41 wt pct Pd, this investigation shows it to be at about 24 wt pct Pd. Moreover, this investigation confirms the existence of compounds at Ti2Pd and Ti2Pd3, whereas Rudnitskii and Birun report only a single Berthol-lide phase covering the TiPd to TiPd, range. Laves et a1.' and Wallbaum, whose work was summarized by Maykuth , reported the existence of Ti2Pd3 and TiPd, in addition to Ti2Pd. More recently, Nevitt and Downe~' have reported the structure of

Jan 1, 1965

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935