Search Documents

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

William M. Courtis, Detroit, Mich. (communication to the Secretary*):—I have a few items to add to the history of the Lake Valley mines. In December, 1879, I was sent to the Bassic mine of Colorado and then to Lone mountain, near Silver City, N. M., and to various copper-camps in Arizona. I staged from Glorietta, N. M., to Tucson, Ariz., stopping at Silver City to see the Cosette mine. This mine led to the opening of the Lake Valley mines, and is a deposit of similar formation. New Year's day, 1880, found me crossing the Rio Grande above the Jornado del Muerto. At Aleman, Victorio's band crossecl four hours ahead of us. We picked up four wounded soldiers to take to Fort Bayard, for during the day the colored troops under General Hatch had been driving the Indians back through the San Andreas mountains. The traveler of to-day little realizes the dangers of these trips, when over very rough roads we made about 100 miles in a day and a night. I subsequently made this trip six times, up to 1882, and each time I missed an Indian attack by from one to four days. The day I arrived at Silver City news had come of the massacre of 75 women and children at the San Francisco ranch. The fighting-men of' Silver City had gone to rescue others. I was the only passenger from Socorro, N. M., until we picked up the soldiers. The next day we came suddenly on 5 of Victorio's band, but we had picked up several miners, so our stage bristled with guns, and we mere let alone. At or near my stone quarry, 6 miles from Socorro, 9 men, were killed by the band that, a day or two after, killed George. Daly, Lieutenant White, and all their men. During this raid, our miners and women at the mine slept in the tunnel. At the Cosette mine I had 35 men at work. These Indian raids had

Jan 1, 1910

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum' of useful samples.

Jan 1, 1939

By Richard J. Borg

The vapor pressure of Cd in equilibrium with CdSb in the presence of excess Sb has been measured using the Knudsen effusion method over the temperature range 276° to 379°C. The free energy of formation of CdSb is given by AF° = -1.58 + 1.53 x l0-4 T, kcal per mole. The enthalpy and entropy are obtained from the temperature coefficient of the .free energy. CADMIUM and antimony have almost imperceptible mutual solid solubility but form a single stable intermediate phase, CdSb. This phase, according to Han-sen,l extends from about 49.5 at. pct to 50 at. pct Cd at 300°C and has the orthorhombic structure. The free energy of formation of CdSb can be calculated from the vapor pressure of Cd for compositions which contain less than 49 at. pct Cd. The appropriate reaction and formulae are given by Eqs. [I] and [2]- CdSb(s, ~ Cd(g)-, +Sb(s) [1] Since Sb is in its standard state, Af - N,,AF'-,, = NcdRT In a,, = NcdRT InP/PO [2] In Eq. [2], P, is the vapor pressure of Cd in equilibrium with the alloy, and Po is the vapor pressure in equilibrium with pure solid Cd. It is implicit in this calculation that the free energy only slightly changes within the narrow limits of the single phase field. Thus, the value obtained from the antimony-rich boundary is truly representative of the stoi-chiometric compound. The results reported herein are obtained from a mixture near the eutectic composition, i.e. 59 at. pct Sb. Only two previous investigations" of the free energy of formation of CdSb have been made. Both relied upon the electromotive force method, and measurements were made over relatively narrow temperature ranges which strongly influences the reliability of the values of AH and aS. EXPERIMENTAL The eutectic composition is prepared by fusing reagent grade Cd and Sb by induction heating in vacuo with the starting materials held in a graphite crucible having a threaded lid. The material obtained from the initial melt is pulverized, sealed under high vacuum in a pyrex capsule, and annealed at 420°C for two weeks. X-ray analysis"gives the following lattize parameters: a = 6.436A, b = 8.230& and c = 8.498A using Cu Ka radiation with A = 1.54056. These values are in fair agreement with the result? previously reported by Al~in:4 i.e. a = 6.471A, b = 8.253A, and c = 8.526A. Vapor pressures are measured using an apparatus which has been described elsewhere,= however, with a single important modification. Knudsen effusion cells are made of pyrex with knife-edged orifices made by grinding the convex surface of the lid on #600 emery paper. Photographs taken at known magnifications using a Leitz metallograph enable the determination of the orifice area. Numerous calibration measurements of the vapor pressure of pure Cd give close agreement with values previously reported5,= thus indicating that no significant error can be ascribed to the substitution of glass cells for metal cells used in previous work. Because the vapor pressure of Cd is reliably established and because it is difficult to obtain Clausing factors for the glass cells, the final values used for the orifice areas are calculated from the calibration measurements of the vapor pressure of pure Cd. Effusion runs are started in an atmosphere of purified helium which is quickly evacuated as soon as the cell attains thermal equilibrium. Less than one minute is necessary to obtain high vacuum after evacuation begins, and the temperature seldom varies by more than 0.5oC from the value obtained prior to pumping out the helium. RESULTS The results of this investigation along with other pertinent data are tabulated in Table I. Fig. 2 is the familiar graph of log P against T-10 K. At least mean squares analysis of the data presented in Table I yields the following equation: log1DJP = 8.790 - 6472 x T"1 [3] The deviations of the individual measurements from the values calculated with Eq. 131 are given in column six of Table I; the average deviation is 4.0% of the calculated value. Although the partial molal properties change significantly with composition within the single phase region, the integral thermodynamic value should remain relatively constant. Hence the results of the following calculations, which use the data obtained for the eutectic composition, are probably representative of the equi-atomic compound. Eq. [4] describes the vapor pressure of pure Cd as a function of temperature and may be combined with Eq. [3] to

Jan 1, 1962

By E. Stansfield, J. W. Sutherland

It is well known that the ash left when coal is burned is not the same either in chemical composition or in weight as the mineral matter originally present in the coal. This mineral matter has been referred to as "mineral impurity," "ash-forming constituents" and "corrected ash." The authors prefer the simple name used in the title and throughout this paper. The mineral matter in a sample of coal cannot be isolated unchanged and then weighed; but if the relation between the weight of mineral matter in the coal and the weight of ash remaining when the coal is burned can be ascertained, the weight of mineral matter in the sample can be calculated from the determined weight of ash. When the weight of mineral matter in the sample is known, the weight of pure coal can be found by subtraction. This pure coal must be the basis of accurate coal classification. W. F. Wheeler,l,3 W. Brinsmaid,2 S. W. Parr, and many subsequent workers have studied the relation between mineral matter and ash. Wheeler and Parr and others have deduced formulas for calculating this ratio, and used heavy-solution separations for checking the accuracy of their formulas. Brinsmaid hand-picked and analyzed two separate samples (and mixtures of these) and based thereon a graphical method of deducing the ratio. In the Fuel Testing Laboratories of the Scientific and Industrial Research Council of Alberta, a graphical method, based on heavy-solution fractionation of coal samples, has been used with marked success for the past 7¼ years for determining the mineral matter-ash ratio. This method resembles that employed by Brinsmaid in 1907.

Jan 1, 1930

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air-pollution control is included. However, there are clear indications that the natural gas supply from the conliguous 48 states and continental shelves will not keep up with this rapid growth in demand indefinitely. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale -by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current mine-mouth prices - 60-70 million tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase in gas demand. Although annual discoveries (gross additions to proved reserves) of natural gas in the United States are still on a general upward trend from the current level of 22 trillion cu ft annually, most forecasters do not expect this to increase substantially in the foreseeable future. For example, the updated (to include 1966 and 1967 data) mathematical model of natural gas discovery and production in the U.S. developed by the Institute of Gas Technology (IGT)' projects that discoveries will level out at about 25 trillion cu ft annually in the late 1970's and during the 1980's and then decline to about 21 trillion cu ft by the year 2000 (Fig. 1). This adds up to a new supply for the period 1968-2000 of about 790 trillion cu ft. Experts who usually reflect the producers' viewpoint, such as Radford L. Schantz of Foster Associates,* are relatively more pessimistic. In contrast, a forecast just made by the U.S. Dept. of the Interior is much more optimistic.3 It assumes an increase in gas discoveries of 2.2% per year over the period 1965-80, reaching about 30 trillion cu ft in 1980. If this rate of increase were extended to the year 2000, annual discoveries would reach 46 trillion cu ft at that time, for a total over the period 1968-2000 of about 1100 trillion cu ft. To these forecasts of new gas discoveries must be added proved reserves of roughly 290 trillion cu ft,4 bringing total U.S. supplies for the rest of the century to nearly 1100 trillion cu ft (IGT) and possibly as high as 1400 trillion cu ft (U.S. Dept. of the Interior). This is approximately the same range as that of two estimates of total remaining recoverable natural gas supply: Potential Gas Committee, 980 trillion cu ft5 and IGT, 1450 trillion cu ft.6 Only the 1965 estimate by the U.S. Geological Survey7 suggests that economically recoverable natural gas supplies will not be exhausted around the end of the century. These forecasts are, naturally, based on the assumption that changes in technological, economic, and regulatory environment as they affect the gas industry will be of an evolutionary, not revolutionary, nature. The various forecasts of potential natural gas supply must now be compared to forecasts of natural gas demand (Table I). The general consensus is that the recent Future Requirements Committee projection to 1990' (extended to the year 2000 by the most recent U.S. Bureau of Mines (USBM) projection9) represents the minimum gas requirements (Table 11). They add up to a total of 1030 trillion cu ft for the period 1968-2000. Even this minimum anticipated gas demand exceeds the total remaining supply estimate by the Potential Gas Committee and would nearly exhaust the proved reserves plus new discoveries projected by IGT. The supply situation would appear much tighter if the demand projections of the Texas Eastern Transmission Gorp.10 and the American Gas Assn.(A.GA.)'' were used (Table I). Yet, these higher forecasts probably do not include the effects of such new markets as gas fuel cells, use of liquefied natural gas as a transport fuel, etc. They also may not fully reflect the impact of air quality control on the fuel market. Obviously, the probable discrepancy between projected supply and demand can only be accommodated in four ways. 1) Rapid increase in exploration and drilling activity to provide new supplies in the amount projected by the optimistic U.S. Dept. of the Interior forecast, coupled with an increase in net pipeline imports from Canada and Mexico from the present 0.5 trillion cu ft per year

Jan 1, 1970

By J. L. Gregg, C. W. Kuttner

ReceNtly there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wiredrawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification. Constituents and Their Identification As far back as 1915 attempts were made to utilize tungsten carbides commercially, but the great brittleness of these carbides made these first attempts unsuccessful. Later, successful dies were made by sintering the powdered carbides with small amounts of iron, nickel, or cobalt. Due to the high melting points of the tungsten carbides (2600" to 2800" C.), it is difficult to melt the carbides without volatilizing almost quantitatively the added element of the iron group. Inasmuch as the added metal does not exceed 20 per cent. and is usually present in much smaller amounts, some understanding of the tungsten-carbon equilibrium dia-

Jan 1, 1929

By C. W. Kuttner, J. L. Gregg

ReceNtly there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wiredrawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification. Constituents and Their Identification As far back as 1915 attempts were made to utilize tungsten carbides commercially, but the great brittleness of these carbides made these first attempts unsuccessful. Later, successful dies were made by sintering the powdered carbides with small amounts of iron, nickel, or cobalt. Due to the high melting points of the tungsten carbides (2600" to 2800" C.), it is difficult to melt the carbides without volatilizing almost quantitatively the added element of the iron group. Inasmuch as the added metal does not exceed 20 per cent. and is usually present in much smaller amounts, some understanding of the tungsten-carbon equilibrium dia-

Jan 1, 1929

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By John D. Roach

DURING an investigation of the yttrium-hydrogen system aimed at producing solid yttrium hydride specimens containing various amounts of hydrogen, it was observed that yttrium containing approximately 2 wt pct H exhibited a tendency to crack and crumble to a powder on standing in air at room temperature. It was also observed that longer hydriding times, at a given temperature, increased this susceptibility to powdering without an increase in hydrogen content, also that moisture in the air is necessary for the observed effects to occur. Even if cracking did not occur, there was a continual formation of a light gray powder on the as-treated surface of the hydrided yttrium and this reaction continues until the entire hydrided piece has been reduced to a powder. Storing the hydrided specimens in the absence of air or removing the surface either by machining or grinding were effective means of preventing this disintegration of hydrided yttrium. In an attempt to determine the reason for this powdering phenomenon, the surfaces of a number of as-hydrided yttrium specimens were examined by X-ray techniques. In all cases the X-ray pattern obtained showed the major phase to be yttrium hydride (YH2) as would be expected since the specimens contained 2 to 2.2 wt pct H. In some cases a trace of yttrium oxide was observed. There was also a third phase present on the surface of these hydrided specimens which could not immediately be identified. This unknown phase was a face-centered cubic material, NaC1-type structure, with a lattice parameter of 4.855 and a calculated density of 5.914 g per cc. Very slight hand polishing of the surface of the hydrided yttrium specimens completely removed both the unknown phase and the traces of oxide so that only the yttrium hydride pattern remained. Based on the X-ray patterns the quantity of the unknown phase on the surface of the hydrided yttrium appeared to be directly related to the susceptibility of the material to powdering. Work at the Denver Research Institute on the yttrium-nitrogen binary system showed that yttrium nitride (YN) is a face-centered cubic material with a lattice parameter of 4.878A and a density of 5.890 g per cc. They also noted that this compound rapidly disintegrated to a powder on standing in air. The unknown pattern observed in the above specimens corresponds very closely to that of the nitride—fcc structure, 4.885 parameter, and density of 5.914 g per cc. The presence of this thin film of nitride on the surface of the hydrided specimens probably accounts for the observed powder formation and crumbling. The nitride reacts with the water vapor in the air (verified by private communication from Dr. C. Huffine, General Electric Co.) to yield yttrium oxide and ammonia. Ammonia is readily detected when hydrided yttrium specimens were allowed to stand in bottled moist air. The powder formed on the surface of the hydrided specimens was shown by X-ray analysis to be yttrium oxide. This reaction appears to occur primarily at the grain boundaries since discrete particles of yttrium hydride separate from the specimens during this powdering process. The reaction of yttrium nitride with water vapor is believed to be as follows: 2YN + 3H2O - Y203 + 2NH3. Despite the fact that this nitride is present only as an extremely thin surface film, if the above reaction is not prevented by removing this film from the surface either by machining or grinding, the reaction continues until the entire hydrided piece has been reduced to a powder. To account for this continuation of the reaction, it is believed that the following reactionalsooccurs: 2YH2 + 2NH3 -2YN + 5H2. The nitride produced by the latter reaction reacts in turn with water vapor. The reaction therefore becomes autocatalytic and continues until the hydride has been consumed and the entire piece reduced to oxide powder. The amount of nitride required to initiate this reaction is quite small and this nitrogen contamination can occur from a number of sources—hydrogen gas employed, minute leak in the hydriding apparatus or even from degassing of the reaction vessel itself. Longer hydriding times increase the possibility of nitrogen contamination and this is especially true when a dynamic gas system is employed in the hydriding process. The production of stable, solid hydrided yttrium is dependent on the complete absence of nitrogen contamination during processing. If such contamination does occur, powdering of the hydrided product can be prevented by removing the nitride from the surface e.g. grinding or by preventing access of air to the pieces e.g. sealing in wax or plastic. The author wishes to express his appreciation to General Electric Co. for sponsoring this research and for permission to publish the results of work under Subcontract AT-93.

Jan 1, 1962

By H. J. Hand

STATISTICAL methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,' written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science,, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should .they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. † Many Useful Statistical Devices Available.-Many statistical methods of attack are available for the analysis of plant data. It is the object of this paper to discuss applications of some of these methods to the solution

Jan 1, 1938

By W. O. Crosby

INTRODUCTION. THE crystalline belt of the Atlantic Seaboard, south of New York, attains its maximum breadth of 220 miles on the northern border of North Carolina; and in this State it is most widely characterized by the occurrence of gold in workable deposits. Half a dozen auriferous belts have been recognized by Nitze and Hanna.1 These are, in the main, coincident in position and trend with the NE.-SW. zones of metamorphic slates and schists, which, more than any other feature, give character to the geological map of North Carolina. The central gold-belts, accompanying the main zone of slates and associated igneous rocks, are much the more important and persistent, and may be regarded as continuous northward across Virginia and southward into South Carolina. Tile eastern belt, on the other band, is the shortest and, economically, one of the least important. Its extreme length does not exceed 25 miles, the narrow band of slaty rocks to which it belongs passing, both NE. and SW., beneath the coastal-plain formations. But, although limited in area and production, this belt is, perhaps, comparable with the central belts or any part of the sea-board crystallines in the variety of conditions under which the gold occurs. It lies chiefly in the NE. part of Franklin county and the NW. part of Nash county, on the watershed of Fishing creek and other tributaries of Tar river. The elevation is between 400 and 500 ft. ; and the Tertiary peneplain has here an exceptionally perfect development, the reliefs separating the slightly incised stream-courses consisting of broad, flat-topped peneplain remnants, bounded by gentle lateral slopes.

Mar 1, 1908

By A. U. Seybolt, R. L. Fullman

THE Hume-Rothery rule relating the relative sizes of the solvent and solute atoms in a substitutional solid solution for moderate to extensive solubility is, of course, well known and much used in the design of alloys. No such rule has been obtained for interstitial solid solutions, although a qualitatively similar relationship would be expected. Among the most common interstitial elements, oxygen, carbon, and nitrogen which can dissolve in important amounts in the transition metals, only in the case of oxygen is there enough solubility data available for an examination of the possibilities of a simple relationship between the extent of solubility and the properties of the metal solvents. Three properties were examined: 1—size of the octahedral space V into which oxygen atoms fit, 2— the elastic modulus E, and 3—the free energy ?F of formation of a low oxide, such as is known to be, or would be expected to be, in equilibrium with the terminal solid solution. The size factor or octahedral volume is so closely associated with the well known Hume-Rothery con- cept of size factor that additional development of this subject is hardly necessary. The octahedral volume used was not corrected to an elevated temperature, as this correction would have made no significant difference. The second factor, Young's modulus E, must be considered, since it is a measure of the strain energy required to force neighboring atoms apart so that an oxygen atom may enter the octahedral volume. The temperature dependence of the elastic modulus of many metals has been reported by Köster,1 but for a rather limited temperature range. Since the

Jan 1, 1955

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923