Search Documents

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Eugene F. Broome, Hugh A. Walls

A diffusion measurement technique based on a shear cell comprised of only two segments is described. The diffusion boundary value problem for the finite capillary geometry is solved in general for any arbitrary initial concentration profile and is subsequently specialized for the modified shear cell problem. Effects of convection and mixing at the shear interface were found to be negligible. Mercury self-diffusion coefficients were determined from -25° to 252°C. These data are in good agreement with those found by Meyer. ALTHOUGH diffusion in liquid metals has been of interest for over two centuries, the need for measurement techniques of improved accuracy and precision has become increasingly apparent as additional data have been obtained and theory has become more refined. These conditions reflect the experimental difficulties inherent in liquid diffusion measurements, in which transport by other processes, such as convection, tends to mask the diffusive transport. Frequently the disagreement between several theoretical predictions is less than that found between different sets of data obtained for a system. Moreover, as has been shown by Nachtrieb,1 diffusion data are needed over much larger temperature ranges if the functional dependence on temperature is to be known. Thus, improved techniques must be devised if experimental data are to augment fundamental understanding of the liquid state and to meet technological needs. The available techniques have been discussed elsewhere.' Of these, only the capillary-reservoir, long capillary, and shear cell techniques will be discussed briefly in terms of experimental advantages and disadvantages. These methods served to establish design criteria for the modified shear cell described here. The capillary-reservoir technique of Anderson and saddington3 has been the most widely used method in recent years. The method offers experimental simplicity relative to other methods and has been employed for high-temperature measurements. Moreover, the mathematical relationship between the measured concentration ratio and the diffusion coefficient is such that smaller values of the ratio are achieved for a specified diffusion time relative to other methods. The amplified errors between the concentration ratio and the calculated diffusion coefficient are diminished at lower values of the ratio.' The method also permits multiple determination by the simultaneous use of several capillaries. Disadvantages of the capillary-reservoir method are primarily associated with the hydrodynamic ef- fects of convection and of placing the capillary in the reservoir. These effects are most pronounced in the region near the open end of the capillary and produce an ill-defined boundary condition between the capillary and the reservoir. Such effects are not amenable to experimental or mathematical correction2 (although this has been suggested4). The long-capillary method of Careri, Paoletti, et al.5-10 involves filling one half of a small capillary tube of 150 to 200 mm total length with material of one composition or radioactivity and the other half with the second part of the diffusion couple. This arrangement eliminates the adverse hydrodynamic effects associated with the capillary-reservoir technique; however, certain other experimental difficulties are encountered in this method. The more significant of these difficulties involve the melting, expansion, contraction, and solidification of the diffusion system. The dependence in some cases of the diffusion coefficient on the capillary diameter noted by Careri et a1.7 (termed the "wall effect") has been alternatively explained by Nachtriebl as a convection effect during solidification. In mutual diffusion measurements, the convection problems associated with melting and solidification are increased because of the differences in melting points and in expansion coefficients between the halves of the diffusion couple. However, the errors caused by convection effects within this method are usually less than those in the capillary-reservoir method. Furthermore, the concentration profile needed to determine concentration-dependent diffusion coefficients by the Boltzmann-Matano analysis can be obtained from this method. Of the previous attempts to use shear cells, only the cell used by Nachtrieb and Petit11,12 appears to have yielded good data. They reduced the mechanical complexity of the conventional shear cell by using a cell comprised of only four segments. Three of these segments were filled with ordinary mercury and the fourth with radioisotopic mercury in their determination of mercury self-diffusion coefficients. The average concentration (radioactivity) was determined in each segment following a period of isothermal diffusion. These concentration values were fitted to concentration profiles obtained from the Stefan-Kawalki tables, and the diffusion coefficients were evaluated. Thus, although the number of cell segments is reduced in their method, some information about the concentration profile can be obtained in terms of the Stefan-Kawalki analysis. Moreover, their cell is suitable for measurement of diffusion coefficients at elevated pressure, as they successfully demonstrated with mercury. Consideration of the design and experimental features of the methods discussed above suggested several criteria for the new cell: 1) a ''total" capillary system, as opposed to a capillary-reservoir system, should reduce adverse convection effects; 2) such a capillary system should avoid the problems en-

Jan 1, 1969

By Norman F. Patton

The subject assigned is so broad that thorough discussion is well-nigh impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. Avenues of Distribution Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer's margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the different communities he serves. His business includes all sizes of anthracite. The third, and by far the most general method, consists in selling to retail dealers, shipments being made direct from the breakers to the yards of the dealers. In large consuming areas, such as the metropolitan districts of New York or Philadelphia, one operator may sell to several

Jan 1, 1936

By Norman F. Patton

The subject assigned is so broad that thorough discussion is well-nigh impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. Avenues of Distribution Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer's margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the different communities he serves. His business includes all sizes of anthracite. The third, and by far the most general method, consists in selling to retail dealers, shipments being made direct from the breakers to the yards of the dealers. In large consuming areas, such as the metropolitan districts of New York or Philadelphia, one operator may sell to several

Jan 1, 1936

By J. C. Rengel

Why and how the nuclear industry entered the electric power generation business is discussed in terms that nuclear energy was an undoubtedly additional energy resource and that it had promise of becoming a virtually inexhaustible generating power if breeder reactors could be devised. The growth of nuclear power, its total generation capacity, are related to the need of increasing energy requirements. The use of atomic energy for power generation will grow if it can compete economically with other fuels. The rate of growth, the time scale and direction of technical development is dependent on ore supplies. It is predicted that by 1980, 50% of all new power installations will be nuclear stations. INTRODUCTION Ten years ago, the nuclear industry was virtually unborn, the Atomic Energy Act of 1954 had just been signed, and peaceful applications of atomic power was little more than a phrase. Serious discussion of the practical application of nuclear energy to electric utility installations in the West was highly unlikely. The questions: Why and how did the nuclear industry enter the electric power generation business at all?; What is the predicted growth of nuclear power?; What technological changes do we predict?; How will the above changes affect the utilities? will in part be answered by this paper. WHY NUCLEAR POWER? The only justification for the West as for any other section of the country for atomic power is economics. Whatever energy source will provide the lowest generation cost will prevail; the only electric utilities which have shown an interest in nuclear power are those to whom it means lower generation costs. It is true that the Government sponsored the development of this technology long before there was any evidence of better economics; but a Government must take a very long-range view and it is the only type of organization that can afford to look more than twenty or thirty years into the future. The Government looked at projections such as shown in Fig. 1, which shows various rates of energy consumption, and matched these against estimates of fossil fuel resources. This showed that we will exhaust our low-cost fossil fuel supplies within 75 to 100 years and our total known fuel supplies within 150 to 200 years. The decision to invest in nuclear energy rested, therefore, on two arguments: a) It was undoubtedly an additional energy resource; and b) It has promise of becoming a virtually inex-haustable resource if breeder reactors could be devised if, while generating power, the reactors would produce more fissile materials than they consumed. This decision produced an unexpected bonus: nuclear power became competitive with fossil power much earlier than had been expected and, as shown in Fig. 2, forced the coal industry to take a hard look at its own position. I believe that the drop of coal prices shown here is the direct result of the entry of nuclear power into the energy supply business. At this point, it ought to be explained why and under what conditions nuclear power can be cheaper than fossil power. Fossil fuel cost to the utility is composed of two factors: a) Mining; and b) Transportation. As a result, the cost of fossil fuel to the utilities varies from 126, 106 Btu to 306, 106 Btu and higher. Nuclear energy is highly concentrated and the transportation factor becomes insignificant. Today the cost of nuclear fuel to the utility ranges between 156

Jan 1, 1967

By Edgar Marburg, William R. Webster

The desirability of bringing about greater uniformity in specifications governing iron and steel is generally recognized, and has found expression within recent years, in the efforts of numerous technical societies in that direction. When the International Association for Testing Materials was organized at Zurich in 1895, a committee was appointed, charged as follows: " On the basis of existing specifications, to seek methods and means for the introduction of international specifications for testing and inspecting iron and steel of all kinds." The American representation on this international committee consisted originally of five, and now of eight members. In view of the magnitude and importance of the subject, the Executive Committee of the American Section of the International Association for Testing Materials, since incorporated as the American Society for Testing Materials, appointed a committee of 34 members, including the American members of the above-named international committee, to frame standard American specifications for iron and steel. This committee reported on specifications for (1) Structural Steel for ridges and Ships; (2) Structural Steel for Buildings; (3) Open-Hearth Boiler-Plate and Rivet-Steel; (4) Steel Rails; (5) Steel Splice-Bars; (6) Steel Axles; (7) Steel Tires; (8) Steel Forgings; (9) Steel Castings ; (10) Wrought-Iron. These specifications were designed to be fairly representa-tive of the best current American practice, and were adopted by letter-ballot of the Society in August, 1901. The leading engineering societies have participated at various times in the discussion of these specifications and have lent valuable assistance through the appointment of special committees on like, or closely related, subjects. The American Society of Civil Engineers discussed the spec-

Jan 1, 1905

By D. A. Munro, G. P. Contractor

Fourteen 50-lb laboratory melts were investigated to determine the effect of uranium on the tenpering characteristics of loo-carbon (0.06 to 0.1 pct C) steels. It was found that uranium additions, particularly in the range 0.30 to 0.45 pct, enhanced the hardness and both ultimate and yield strength of the experivzental steels in the quenched and tempered condition. The structural and morphological chazges indicated that uranium retarded tempering of the tnartensite, thereby hindering the normal formation of polygonal ferrite formed in the late stages of tempering. The effect of this was to make possible the re-tension of the acicilar ferritic structure in the uranium-bearing' steels. The iraniuin-bearing steels also showed IVidnzanstatten-type growth of ferrite plates and had large prior austenite grains containing assenzblies of fine ferrite grains, mainly acicular in geometry. The fine-grained ferrite structure and the presence of more numerous and apparently smaller precipitates in the uranium-bearing steels are thought to he principally responsible for the itnproved tensile strength and hardness of the experinzental uranium-bearing steels. At ternperirzg temperatures above 455% (850'F) the ferrite in the higher-uraniun steels nzaintained acicularity and, hence, its strength and resistance to tempering. Uranium did not produce a secondary hardening peak. However, it retarded softening during the third stage of tempering because of its effect of inhibiting the grouth of cementite particles and of retaining the acicularity of ferrite plates. The resistance to coalescence accounted for the slow grocth of the ferrite grains in the uranium-modified steels and, hence, fov the persistence of the acicular ferrite structure. IT had been found previously1 that uranium additions up to about 0.45 pct had no significant effect on the tensile properties of low-carbon steel (0.06 to 0.10 pct C) in the as-rolled and normalized conditions, Fig. 1. On the other hand, it was observed that uranium in excess of about 0.30 pct had an embrittling effect as revealed by Charpy V-notch impact results. It was also noted that, as the uranium content increased, the morphology of pearlite changed from lamellar to feathery and the ferrite grains showed an etching effect resembling striated or dashed markings, suggestive of precipitation. The sharp drop in the impact properties shown in Fig. 2 warranted an assumption that the uranium content of about 0.30 to 0.45 pct may produce some secondary hardening reaction on tempering, analogous to that associated with a Cr-Mo-V steel, which shows very poor CVN toughness at the secondary hardness peak in the tempering curve.1' With this background and the reported findings of Hasegawa and noda that low-carbon uranium-treated steel showed signs of secondary hardening, the present investigation was undertaken to determine the effect of uranium additions on the mechanical properties of 0.10 pct C steels. No attempts were made to investigate in detail the mechanisms of hardening, although some suggestions based on the experiments are made. MATERIALS AND PROCEDURES A series of 50-lb induction-furnace melts was made using AISI 1008 rimming steel billets as the melting stock. The melting, forging, and rolling techniques proven satisfactory in previous projects'-3 were employed as a guide for this investigation. The steel was deoxidized with aluminum (2 lb per ton) prior to the addition of high-purity uranium. The analysis of each melt is given in Table I. Properties were evaluated as a function of heat treatment and are presented in terms of hardness and tensile strength vs tempering temperatures. The variation of hardness with the tempering temperature was studied on the quenched and tempered specimens, some of which measured 0.50 by 0.25 in. diam and the others 0.40-in. cubes. Before quenching, the specimens were vacuum-sealed in glass tubes and normalized at 900°C (1650°F) for 20 min. Following this treatment, the sealed specimens were hardened by austenitizing at 955°C (1750°F) for 20 min and water quenching, and then tempered for 1 hr in the range 150 to 730°C

Jan 1, 1967

By P. G. Shewmon

A novel technique for determining the surface energy (?) and its derivative with respect to orientation, (?') is described. Essentially it involves the 'floating" of a wedge on the substrate, said wedge being made of a material which is not wet or only slightly wet by the substrate, i. e., as a greased needle "floats" on water. A thermodynamic analysis of a system in which the wedge is supported entirely by surface energy is given. If the original suyface is not at a cusp orientation, the surface tension is directly measurable from the groove angle formed. If the original surface is at a cusp orientation, there may or may not be a groove depending on the relative value of ?' and the weight of the wedge. Experiments primarily on copper and silver showed that sapphire, quartz and refractory metal wedges were wet while graphite wedges were not. The technique was demonstrated to work using graphite wedges, but the results obtained were not as eccurate as those obtained by other workers using the wire-creep experiments. It is concluded that the technique might prove most useful with non-metals where ?' is large and filament creep experiments would be quite difficult. If an absolute value of the surface free energy (?) of a metal is to be determined, the most reliable methods used to date measure an average over the various orientations exposed on a polycrystalline sample. For example, ? for silver, gold, and copper have been measured by determining the force required to just keep a thin wire,' or foil,' specimen from contracting under the influence of ?. Herring 3 has predicted and experiment confirms, that the sensitivity of this method is inversely proportional to the grain size.' Thus it cannot be used to measure ? for a particular orientation by using a foil single crystal or a very coarse-grained specimen. An accurate value if ? for tungsten averaged over a range of orientations has been determined using a field emission technique. The same techniques cannot or have not been used to measure ? for non-metallic solids, and as a result the values available are much less accurate.4 This Paper resents a means of making an absolute determination of ? for a particular surface orientation on any solid, as long as the given surface orientation does not break up into other orientations during an anneal. Experimentally ? is found to vary with orientation and at a few low index orientations it is found to have a cusped minimum, i.e., the derivative of ? with respect to the orientation of the surface changes discontinuously at the low index orientation, see Fig. 1. The slope of a plot of ? vs orientation (herein designated ?') is called the torque on the surface, since it tends to rotate the exposed surface toward the low index orientation, or if the surface is at the cusp orientation it opposes any force tending to rotate the surface out of the low index orientation. The ratio ?'/? has been determined for a few metals, but in cases where this ratio is high there is presently no means of determining either ?'/? or the absolute value of ?' for the orientations present on an annealed surface. The technique discussed herein also provides a means of determining an absolute value of ?' for those orientations which deviate only infinitesimally from a cusp orientation. It should work best on surfaces where ?'/? is large; that is, for cases where no other technique is available for measuring ?'. Aside from trying to learn more about surfaces through measuring ? and ?', the primary reason for wanting values of ? or ?' is to study adsorption. From measurements of the variation of ? for a particular orientation with the concentration of an impurity, one can obtain the number of impurity atoms adsorbed per unit area (Ti) on that orientation using the Gibbs adsorption equation.' where µi is the chemical potential of the adsorbed impurity. Thus, if absolute values of ? could be obtained for the free surface of a given surface orientation as a function of µi, ri could be determined for the given orientation. Furthermore, by equilibrating a grain boundary with the given surface at various values of ki, one could also determine ri for the grain boundary. Similarly Robertson 6 has pointed out that if y is taken to be a continuous function of and µi, then a2 ?/a @a µ2 = a2 ?/a pi a +. Thus, at all orientations away from cusps the following equation holds From a measurement of ?' vs ki, it is thus possible

Jan 1, 1963

The Cuajone and Toquepala copper projects are located in the extreme southern area of Peru. Since 1960, Southern Peru Copper Company has operated the Toquepala open -pit mine, flotation mill, 110 smelter, townsites, power plants, and railroad. Toquepala and 10, the smelter and port location, are connected by a 110-mile-long (176 lun) railroad. Much of Toquepala's infrastructure has been used for the Cuajone project. Cuajone, at an elevation of 11,400 ft (3475 m), required five standard-guage railroad tunnels with a combined length of 17 miles (27.2 km) to connect with Toquepala so concentrates could be shipped to the no smelter. The total cost of Cuajone is estimated at $726 million for a designed annual capacity of 180,000 tons of copper, equivalent to about $4,000 per ton of installed production capacity. This relatively low cost per ton, by today's standards, has been made possible through the use of the 110-to Toquepala railroad, the ability to expand the 110 copper smelter, and other favorable factors. To mine the 468 million tons of copper sulfide or e at a grade of 1.0% copper, approximately 24 1 million tons of waste were stripped- before mining of ore to supply the new Botiflaca 45, 000 ton per day concentrator. The mining rate must exceed 300,000 tons of waste plus ore per day to maintain the 45, 0 00 tpd sulfide ore milling rate which was to be reached at the end of 1976. Waste stripping is done with 15 cu yd electric shovels and 120 -ton trucks. Ore mining is done with 8 and 9 yd shovels. A railroad connects the pit with the 60 in. by 89 in. Allis-Chalmers gyratory crusher. Side-dump railroad cars of 50.cu yd capacity dump onto a 0 16 ft 9 in. long (5. 1 m) grizzly inclined at 40º with 7 to 8 in. (178 to 203 rnrn) bar spacings. The grizzly is divided into two 22 ft 4 in. (6.8 m) wide sections and two side -dump railroad cars discharge simultaneously into the 150-ton capacity dump pocket. A Barco rock manipulator is used for breaking or removing oversize from the dump pocket. The bin receiving the grizzly undersize has a capacity of 5,000 tons, and the pocket beneath the crusher holds 900 tons. Each is equipped with an 84 in. apron feeder, which feeds a 60 in. (1.52 m) conveyor belt to the 150,000 ton coarse ore stockpile, where the ore is distributed by a 72 in. (1. 83 m) tripper conveyor. The 45, 000 live tons in the coarse ore stockpile are reclaimed by twelve 48 in. (1. 22 m) apron feeders. Maintenance on the crusher eccentric is made easy by an eccentric

Jan 1, 1978

By Homer Turner

COALS, other than anthracite, have been so thoroughly studied under the microscope during recent years, that we now know what kinds of plants and what parts of plants form the bulk of lower rank coals from peat to bituminous coal. The microscope has also shown the state of preservation of such vegetation as well as the nature and distribution of products of plant decay. These and further details have been ascertained mainly through the employment of two methods of attack, section cutting and maceration. Anthracite has failed to respond to these methods, so well adapted to the study of lower rank coals and, therefore, has been neglected by investigators to such an extent that there is much doubt as to its microscopical characteristics. The object of this paper is to lift anthracite from its realm of obscurity by demonstrating the wealth of microscopical detail that is revealed when reflected light is used on a properly polished and etched surface and, further, to show the relationship between anthracite and bituminous coal.

Jan 2, 1925

By E. V. Daveler

The milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. Character of Ore The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver............ 0.10 oz. Magnesia......... 0.4 per cent. Silica............. 59.7percent. Sulfur............ 1.2 per cent. Iron.............. 5.2 per cent. Lead............. 0.1 per cent. Alumina.......... 21.4percent. Zinc............. 0.2percent.. Lime............. 5.0 per cent. Experimental Work Investigations at the old Perseverance stamp mill had developed the following points: Roughing concentration following stamping gives a fair recovery.

Jan 1, 1920

By J. C. Wright

A practical program of education for workers of the mining industries is being formulated by the Federal Board for Vocational Education in cooperation with the states in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational education and for cooperation with the states in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the 1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manfactures Mines and quaRRies Employees.......... 7,405,313 1,109,410 Capital............. $18,428,269,706 53,380,525,841 Value of product..... $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all states have set up educational and technical standards for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some states, every miner must have a certificate, which is issued by the mine examining board only after an oral examination. Did these state laws not call for definite and comprehensive plans for the vocational education of men in the mining regions, the conditions

Jan 1, 1919

By AIME AIME

The name and address of the school are given first, followed by the length of the regular undergraduate curriculum, the degree granted, types of courses giben, and the name of the man in charge. This covers only work for the first or Bachelor degree in each case. The following abbreviations are used: B. Bachelor Cer. Ceramic. E. Engineer or Engineering Eng. Engineering or Engineer Geol. Geologist, Geological, or Geology M. Mines or Mining Met. Metallurgy or Metallurgical Mng. Mining Pet. Petroleum Ref. Refining S. Science Tech. Technology or Technical

Jan 1, 1939

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a previous paper.1 The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques.

Jan 12, 1953

By D. J. Jr. McAdam

RESULTS of a general survey of corrosion-fatigue phenomena at the Naval Engineering Experiment Station were presented in five previous papers.1-5 In these papers references were given to the work of Haigh in 1917.6 The five papers mentioned gave a general survey of the behavior of metals when tested to failure under simultaneous corrosion and cyclic stress. As a result of this survey the fourth paper gave a tentative analysis of the corrosion-fatigue process. According to this analysis, if the initial stress is below the endurance limit but above the corrosion-fatigue limit, the corrosion-fatigue process is divided into two periods. The first period is the formation of pits. As the initial stress is below the endurance limit, the pitting is assumed to be due to corrosion, not to fatigue. The corrosion pitting, however, is not the ordinary pitting of stressless corrosion, but is an accelerated pitting due to the effect of the cyclic stress on the corrosion. As the pit progresses, both the actual stress and the effective solution pressure increase. The increase of actual stress is due to increasing stress concentration at the bottoms of the pits. The increase of effective solution pressure is due to the increase of actual stress. The mutual intensification of stress and solution pressure continues until the actual stress at the bottoms of the pits surpasses the endurance limit. The second period of corrosion-fatigue then begins. In this period the process is merely fatigue accelerated by the corrosion. The cracks advance at a continually accelerated rate until the specimen breaks.

Jan 1, 1930

THE National Coal Association held its annual meeting at Cleveland on Nov. 14-16, 1928, having changed the time from the spring to the autumn to avoid conflict with the great number of meetings ordinarily held in the spring. Institute members were \\yell to the fore in its activities, the president, E. C. Mahan (who was reelected for another term!, C. E. Bockus, treasurer, and the secretary, H. L. Gancly, being A. I. M. E. members, as are many of the directors. At the first session, our past president, S. A. Taylor, presented a 1;aper which is reprinted in part herewith. At the Thurs- day session W. D. Brennan presided, Walter Barllum led the discussion on membership, and Otis Mouser led the discussion on taxation. In the afternoon, J. P. Williams, Jr., led the discussion on research. Rembrandt Peale presided at the annual dinner in the evening. At the concluding session on Friday resolutions were adopted, among them one in which the Association "reaffirms its attitude toward proposed Federal legislation affecting the bituminous coal industry by saying that it opposes legislation which would seek to single out this industry for regulatory action. This particularly applies to such bills as S4490."

Jan 1, 1928

By Alfred E. Hunt, Geo. H. Clapp

The great advantage to he gained by a careful inspection of all materials used in construction, in regard to safety and permanency, and to accuracy of workmanship, has been longer recognized in Great Britain and on the Continent than in America. This is probably owing to the way in which great enterprises have been " rushed" in the United States. Time and cheap first cost, in too many instances, have been considered of more importance than absolute safety and durability; the structures being afterwards strengthened if this was found necessary. This has been most noticeable in railroads built through " new " country, where the object in view has been to reach the terminal point and get to work. These " loose " methods are now being very largely done away with, and a large proportion of the structures lately built are not only carefully inspected during the process of

Jan 1, 1891

By Chauncey L. Berrien

The United Verde Copper Company's mine is at Jerome, Ariz. The orebodies arc of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. Three types of ore are mined; schist porphyry and the so-called "heavy" or "massive sulfide" ore. Approximately 50 per cent. of the total tonnage mined at present is of the latter class. A representative analysis of this ore indicates 42 to 46 per cent. sulfur. Because of the high sulfur content, blasting in this ore is an extremely hazardous operation. not only does it endanger the lives of men who may be in the mine at blasting time but it also becomes a potential fire menace when timber is in close proximity to shots being fired in these massive sulfides. The origin of the fires of 38 years ago, embers of which are glowing to this day, may perhaps be attributed to dust explosions due to blasting in the massive sulfides of those early square-set stopes. Dust Explosions Dust explosions in coal mines are a common source of mine disasters. That such explosions may be of common occurrence in metal mines is not generally known, but it is known that metal-mine dust will explode and such explosions have been investigated by the U. S. Bureau of Mines at the Pittsburgh Experiment Station. Samples of "heavy sulfide" ore from the United Verde mine were used in the tests. After studying the results of the tests it was concluded1 that: 1. Dust explosions were initiated in sulfide ore dust in the gallery with a charge of as low as 75 g. of 60 per cent. gelatin dynamite. 2. The exploding dust generated considerable pressure.

Jan 1, 1930

Jan 1, 1891

By J. L. Lytton, T. E. Tietz

The recovery of flour stress of recrylstallized are-cast molyhdenum after 10 pet prestrain at 150°C was studied for recovery temperatures of 725o 801o and 901oC. The yield phenomenon observed after recovery was such that the yield drop diminished and disappeared as recovery proceeded. A fractional flow-stress recovery parameter fr, was developed and it was shown that, independent of recovery ternperatzwe, equal f, values of about 0.16 produced superposition of stress-strain curves except for the initial yield phenomenon. The activation energy for low degrees oj recovery was found to he 32,600 cal per mole, in close agreement with a reported valzie for difjzdsion of carbon in molybdenum. For values of fr greater than about 0.15 where recovery was thought to predominate over strain aging, the activation energy varied from 43,600 to 82,500 cal per mole and increased with increasing recovery and recovery temperature. A 10 pet pre-strain shifted the ductile-brittle transition temperature, as indicated by tensile elongation, from 10°C. to about -22"C. A 100-hr recovery anneal at 801oC was shown to shift the transition temperature to about —5oC, the major shift occurring during the first hour of recovery. ThE recovery of cold-worked metals is accompanied by changes in the arrangement of the dislocations generated during cold work. In recent years, the use of transmission electron microscopy has allowed direct observation of some of the dislocation configurations formed, such as "tangles", networks, cells, subboundaries, and loops. These observations have recently been reviewed by Keh and Weissmann.' Accordingly, some understanding has been gained concerning the nature of the dislocation rearrangements involved. The relationship between recovery and the decrease of mechanical strength, however, has only recently been explored. Previous efforts of the authors were directed toward investigating the decrease of tensile flow stress of aluminum and Al-1 pet Mg during recovery2 and the effects of concurrent elastic and plastic strain on the flow-stress recovery of aluminum.3 In addition, an investigation of the effect of four different solute additions on the tensile flow-stress recovery of aluminum has been made.4 Many important metals, however, have the bee crystal structure, e.g., iron, molybdenum, tungsten, vanadium, columbium, tantalum, and chromium. These metals might be expected to behave differently during recovery from those with other crystal structures for two reasons. First, the previous and present investigations of aluminum and its alloys have shown that tensile flow-stress recovery is strongly affected by foreign atoms in the lattice. In the bee metals, interstitial impurities are usually present and might be expected to have various effects upon both flow behavior and recovery. For example, heterogeneous yielding might occur during prestraining. The diffusion of these interstitials can also relock dislocations during recovery so that a yield point might be obtained upon restraining (strain aging). Second, some of the bee metals (e.g., iron, molybdenum, and tungsten) undergo the familiar structure-sensitive ductility transition and exhibit brittle fracture at suitably low temperatures. It is of considerable interest to determine the effects of recovery on the transition temperature of such metals. The purpose of the present investigation was to extend our knowledge of flow-stress recovery to the bee metals and to study the effects of recovery on the ductile-brittle transition temperature. Unalloyed recrystallized are-cast molybdenum was chosen as a test material, since it exhibits a well-defined ductility transition near room temperature. As in the previous studies, the degree of recovery was measured in terms of the decrease of tensile flow stress. Prestraining and restraining were carried out at 150°C to avoid the possibility of brittle fracture. EXPERIMENTAL PROCEDURE The are-cast molybdenum sheet used in this investigation was obtained from the Climax Molybdenum Co. of Michigan. It was 0.060 in. thick by 10

Jan 1, 1964